A potentiometer may be used for?

by

1 Answer

Answer :

A potentiometer may be used for measurement of resistance, measurement of current, calibration of ammeter, calibration of voltmeter.

by

Related questions

When the voltage across a battery is measured using a D.C potentiometer, the reading shows 1.08 V. But

Description : When the voltage across a battery is measured using a D.C potentiometer, the reading shows 1.08 V. But when the same voltage is measured using a Permanent Magnet Moving Coil (PMMC) voltmeter, the voltmeter reading shows 0.99 ... resistance of the battery, in Ohm , is (A) 150 (B) 100 (C) 50 (D) 200

Last Answer : When the voltage across a battery is measured using a D.C potentiometer, the reading shows 1.08 V. But when the same voltage is measured using a Permanent Magnet Moving Coil (PMMC) voltmeter, ... resistance of the voltmeter is 1100 Ohm , the internal resistance of the battery, in Ohm , is 100

In an AC. co-ordinate potentiometer, the currents in the phase and quadrature potentiometer are adjusted to be?

Last Answer : In an AC. co-ordinate potentiometer, the currents in the phase and quadrature potentiometer are adjusted to be out of phase by 90°.

The stator of phase shifting transformer for use in conjunction with an A.C. potentiometer usually has a?

Last Answer : The stator of phase shifting transformer for use in conjunction with an A.C. potentiometer usually has a two-phase winding.

To measure an A. C. voltage by using an A.C. potentiometer, it is desirable that...

Description : To measure an A. C. voltage by using an A.C. potentiometer, it is desirable that the supply for the potentiometer in taken?

Last Answer : To measure an A. C. voltage by using an A.C. potentiometer, it is desirable that the supply for the potentiometer in taken from the same source as the unknown voltage.

In order to achieve high accuracy, the slide wire of a potentiometer should be?

Last Answer : In order to achieve high accuracy, the slide wire of a potentiometer should be as long as possible.

Basically a potentiometer is a device for?

Last Answer : Basically a potentiometer is a device for comparing two voltages.

To measure a resistance with the help of a potentiometer it is?

Last Answer : To measure a resistance with the help of a potentiometer it is not necessary to standardise the potentiometer.

A rheostat differs from potentiometer in the respect that it?

Description : A rheostat differs from potentiometer in the respect that it?

Last Answer : A rheostat differs from potentiometer in the respect that it has higher wattage rating.

can we use potentiometer for measuring resistance?

Last Answer : Yes we can use potentiometer for measuring resistance.

A d.c. potentiometer is designed to measure up to about 2V with a slide wire of 800 mm. A standard cell of

Description : A d.c. potentiometer is designed to measure up to about 2V with a slide wire of 800 mm. A standard cell of emf 1.18V obtains balance at 600 mm. A test cell is seen to obtain balance at 680 mm. The emf0fthe test cell is  A)1.00V B)1.34V C)1.50V D)1.70V 

Last Answer : A d.c. potentiometer is designed to measure up to about 2V with a slide wire of 800 mm. A standard cell of emf 1.18V obtains balance at 600 mm. A test cell is seen to obtain balance at 680 mm. The emf0fthe test cell is 1.34V

Potentiometer sensitivity can be increased by

Last Answer : Potentiometer sensitivity can be increased by Increasing the length of potentiometer wire.

What is a potentiometer in Arduino?

Description : What is a potentiometer in Arduino?

Last Answer : A potentiometer in Arduino is a variable resistor that can be used to control the brightness of an LED, the speed of a motor, or the volume of a speaker.

What is a potentiometer in Arduino?

Description : What is a potentiometer in Arduino?

Last Answer : A potentiometer in Arduino is a variable resistor that can be used to adjust the voltage level or control the position of a servo motor.

What is a potentiometer in Arduino?

Description : What is a potentiometer in Arduino?

Last Answer : A potentiometer is an electronic component used in Arduino projects to vary the resistance in a circuit.

How can I wire a doubled up Potentiometer to cut two different frequencies?

Description : How can I wire a doubled up Potentiometer to cut two different frequencies?

Last Answer : answer:Not quite sure I understand (and even if I do, not sure I can help, but I'll try). Are you saying that you want to re-purpose your tone knob to be a balance knob between the two ... pickups wired in parallel) that will widen on the treble side above 5 and widen on the base side below 5?

What is a potentiometer ?

Description : What is a potentiometer ?

Last Answer : : Potentiometer is a device used to measure voltage difference and electromagnetic force in a voltage drop method.

In a potentiometer experiment the balancing with a cell is at length 240 cm. On shunting the cell with a resistance of `2Omega`, the balancing length

Description : In a potentiometer experiment the balancing with a cell is at length 240 cm. On shunting the cell with a resistance of `2Omega`, the balancing length

Last Answer : In a potentiometer experiment the balancing with a cell is at length 240 cm. On shunting the cell with a ... Omega` C. `4 Omega` D. `2 Omega`

Potentiometer measures the potential difference more accurately than a voltmeter, because

Description : Potentiometer measures the potential difference more accurately than a voltmeter, because

Last Answer : Potentiometer measures the potential difference more accurately than a voltmeter, because A. it does not ... resistance D. it has a low resistance

In potentiometer experiment, a cell of emf `1.25 V` gives balancing length of 30 cm. If the cell is replaced by another cell, then balancing length is

Description : In potentiometer experiment, a cell of emf `1.25 V` gives balancing length of 30 cm. If the cell is replaced by another cell, then balancing length is

Last Answer : In potentiometer experiment, a cell of emf `1.25 V` gives balancing length of 30 cm. If the cell is replaced by another ... . `~=1.47 V` D. `~=1.37 V`

An electron in potentiometer experiences a force `2.4xx10^(-19)N`. The length of potentiometer wire is 6m. The emf of the battery connected across the

Description : An electron in potentiometer experiences a force `2.4xx10^(-19)N`. The length of potentiometer wire is 6m. The emf of the battery connected across the

Last Answer : An electron in potentiometer experiences a force `2.4xx10^(-19)N`. The length of potentiometer wire is 6m. The emf of ... 6 V B. 9 V C. 12 V D. 15 V

A potentiometer wire of length 10 m and resistance `10 Omega` per meter is connected in serice with a resistance box and a 2 volt battery. If a potent

Description : A potentiometer wire of length 10 m and resistance `10 Omega` per meter is connected in serice with a resistance box and a 2 volt battery. If a potent

Last Answer : A potentiometer wire of length 10 m and resistance `10 Omega` per meter is connected in serice with a ... Omega` C. `190 Omega` D. `90 Omega`

A potentiometer wire of length `100 cm` having a resistance of `10 Omega` is connected in series with a resistance `R` and a cell of emf `2V` of negli

Description : A potentiometer wire of length `100 cm` having a resistance of `10 Omega` is connected in series with a resistance `R` and a cell of emf `2V` of negli

Last Answer : A potentiometer wire of length `100 cm` having a resistance of `10 Omega` is connected in series with a ... Omega` C. `790 Omega` D. `840 Omega`

A potentiometer wire has length `4 m` and resistance `8 Omega`. The resistance that must be connected in series with the wire and an accumulator of e.

Description : A potentiometer wire has length `4 m` and resistance `8 Omega`. The resistance that must be connected in series with the wire and an accumulator of e.

Last Answer : A potentiometer wire has length `4 m` and resistance `8 Omega`. The resistance that must be connected in ... Omega` C. `44 Omega` D. `48 Omega`

A potentiometer wire is `100 cm` long hand a constant potential difference is maintained across it. Two cells are connected in series first to support

Description : A potentiometer wire is `100 cm` long hand a constant potential difference is maintained across it. Two cells are connected in series first to support

Last Answer : A potentiometer wire is `100 cm` long hand a constant potential difference is maintained across it. Two cells are connected ... C. `3 : 2` D. `5 : 1`

Assertion : In potentiometer experiment, null point cannot be obtained if emf of unknown battery is more than the emf of known battery. Reason : By in

Description : Assertion : In potentiometer experiment, null point cannot be obtained if emf of unknown battery is more than the emf of known battery. Reason : By in

Last Answer : Assertion : In potentiometer experiment, null point cannot be obtained if emf of unknown battery is ... If Assertion is false but Reason is true.

Assertion : In case of potentiometer experiment, if emfs of known and unknown both batteries are increased two times, then null point length will rema

Description : Assertion : In case of potentiometer experiment, if emfs of known and unknown both batteries are increased two times, then null point length will rema

Last Answer : Assertion : In case of potentiometer experiment, if emfs of known and unknown both batteries are ... If Assertion is false but Reason is true.

A `1 Omega` resistance in series with an ammeter is balanced by 25 cm of potentiometer by 50 cm. The ammeter shows a reding of `1.5 A`. Then, the erro

Description : A `1 Omega` resistance in series with an ammeter is balanced by 25 cm of potentiometer by 50 cm. The ammeter shows a reding of `1.5 A`. Then, the erro

Last Answer : A `1 Omega` resistance in series with an ammeter is balanced by 25 cm of potentiometer by 50 cm. The ammeter shows a ... B. 3A C. `1.3 A` D. `0.3A`

A potentiometer circuit is setup as shown. The potential gradient across the potentiometer wire is `k "volt"//cm` and the ammeter present in the circu

Description : A potentiometer circuit is setup as shown. The potential gradient across the potentiometer wire is `k "volt"//cm` and the ammeter present in the circu

Last Answer : A potentiometer circuit is setup as shown. The potential gradient across the potentiometer wire is `k "volt"//cm` and ... (2)` D. `kl_(1)"and"kl_(2)`

In given figure, the potentiometer wire AB has a resistance of `5 Omega` and length 10 m . The balancing length AM for the emf of 0.4 V is

Description : In given figure, the potentiometer wire AB has a resistance of `5 Omega` and length 10 m . The balancing length AM for the emf of 0.4 V is

Last Answer : In given figure, the potentiometer wire AB has a resistance of `5 Omega` and length 10 m . The balancing length AM for ... B. 4 m C. `0.8` m D. 8 m

The length of a wire of a potentiometer is 100 cm, and the e.m.f. of its standard cell is E volt. It is employed to measure the e.m.f. of a battery wh

Description : The length of a wire of a potentiometer is 100 cm, and the e.m.f. of its standard cell is E volt. It is employed to measure the e.m.f. of a battery wh

Last Answer : The length of a wire of a potentiometer is 100 cm, and the e.m.f. of its standard cell is E ... current in the potentiometer wire D. `(30E)/(100)`

A potentiometer having the potential gradient of `2 mV//cm` is used to measure the difference of potential across a resistance of `10 ohm`. If a lengt

Description : A potentiometer having the potential gradient of `2 mV//cm` is used to measure the difference of potential across a resistance of `10 ohm`. If a lengt

Last Answer : A potentiometer having the potential gradient of `2 mV//cm` is used to measure the difference of potential across a ... `) A. 1 B. 2 C. 5 D. 10

AB is a potentiometer wire of length 100 cm and its resistance is `10Omega`. It is connected in series with a resistance R = 40 `Omega` and a battery

Description : AB is a potentiometer wire of length 100 cm and its resistance is `10Omega`. It is connected in series with a resistance R = 40 `Omega` and a battery

Last Answer : AB is a potentiometer wire of length 100 cm and its resistance is `10Omega`. It is connected in series with a ... `1.6V` C. `0.08V` D. `0.16V`

For a cell of e.m.f. 2 V , a balance is obtained for 50 cm of the potentiometer wire. If the cell is shunted by a `2Omega` resistor and the balance is

Description : For a cell of e.m.f. 2 V , a balance is obtained for 50 cm of the potentiometer wire. If the cell is shunted by a `2Omega` resistor and the balance is

Last Answer : For a cell of e.m.f. 2 V , a balance is obtained for 50 cm of the potentiometer wire. If the cell is ... B. `0.50Omega` C. `0.80Omega` D. `1.00Omega`

A potentiometer having the potential gradient of `2 mV//cm` is used to measure the difference of potential across a resistance of `10 ohm`. If a lengt

Description : A potentiometer having the potential gradient of `2 mV//cm` is used to measure the difference of potential across a resistance of `10 ohm`. If a lengt

Last Answer : A potentiometer having the potential gradient of `2 mV//cm` is used to measure the difference of potential across a ... `) A. 1 B. 2 C. 5 D. 10

A 2 V battery, a `990Omega` resistor and a potentiometer of 2 m length, all are connected in series of the resistance of potentiometer wire is `10Omeg

Description : A 2 V battery, a `990Omega` resistor and a potentiometer of 2 m length, all are connected in series of the resistance of potentiometer wire is `10Omeg

Last Answer : A 2 V battery, a `990Omega` resistor and a potentiometer of 2 m length, all are connected in series of the resistance ... 0.01Vm^(-1)` D. `0.1Vm^(-1)`

Two cells of emfs `E_(1)` and `(E_(2) (E_(1) gt E_(2))` are connected as shows in Fig. `6.45`. When a potentiometer is connected between `A` and `B`,

Description : Two cells of emfs `E_(1)` and `(E_(2) (E_(1) gt E_(2))` are connected as shows in Fig. `6.45`. When a potentiometer is connected between `A` and `B`,

Last Answer : Two cells of emfs `E_(1)` and `(E_(2) (E_(1) gt E_(2))` are connected as shows in Fig. `6.45`. When a ... `3:1` B. `1:3` C. `2:3` D. `3:2`

The resistivity of a potentiometer wire is `40xx10^(-8)Omega-m` and its area of cross section is `8xx10^(-6)m^(2)`. If 0.2 A current is flowing throug

Description : The resistivity of a potentiometer wire is `40xx10^(-8)Omega-m` and its area of cross section is `8xx10^(-6)m^(2)`. If 0.2 A current is flowing throug

Last Answer : The resistivity of a potentiometer wire is `40xx10^(-8)Omega-m` and its area of cross section is `8xx10^(-6)m^(2)` ... . `3.2xx10^(-2)V//m` D. `1V//m`

For measurement of potential difference, potentiometer is perferred in comparison to voltmeter because

Description : For measurement of potential difference, potentiometer is perferred in comparison to voltmeter because

Last Answer : For measurement of potential difference, potentiometer is perferred in comparison to voltmeter because A. ... does not take current from the circuit

Potentiometer wire of length `1 m` is connected in series with `490 Omega` resistance and `2 V` battery. If `0.2 mV/cm` is the potential gradient, the

Description : Potentiometer wire of length `1 m` is connected in series with `490 Omega` resistance and `2 V` battery. If `0.2 mV/cm` is the potential gradient, the

Last Answer : Potentiometer wire of length `1 m` is connected in series with `490 Omega` resistance and `2 V` battery. If ... 7.9Omega` C. `5.9Omega` D. `6.9Omega`

In a potentiometer experiment, the galvanometer shows no deflection when a cell is connected across `60 cm` of the potentiometer wire. If the cell is

Description : In a potentiometer experiment, the galvanometer shows no deflection when a cell is connected across `60 cm` of the potentiometer wire. If the cell is

Last Answer : In a potentiometer experiment, the galvanometer shows no deflection when a cell is connected across `60 cm` of ... ` C. `1.2Omega` D. `1.5Omega`

Define potentiometer?

Description : Define potentiometer?

Last Answer : A dual potentiometer is nothing but a potentiometer which has TWO channels.. Like two INs and two OUTs on the same unit.

The pH value of sewage is determined with the help of A. Imhoff Cone B. Turbid meter C. Potentiometer D. None of these

Description : The pH value of sewage is determined with the help of A. Imhoff Cone B. Turbid meter C. Potentiometer D. None of these

Last Answer : ANS: C

The electrical device shown in the illustration is a/an _____________. EL-0077 A. operating coil B. indicating lamp C. motor armature D. potentiometer

Description : The electrical device shown in the illustration is a/an _____________. EL-0077 A. operating coil B. indicating lamp C. motor armature D. potentiometer

Last Answer : Answer: D

In the illustrated amplifier, the RESET potentiometer A1R2 sets the stability of the control loop by changing the reset time constant. As the potentiometer is turned clockwise _________. EL-0060 A. the gain is increased B. the stability is increased by slowing the response time C. feedback is increased to the summing point at terminal 5 D. response time is increased decreasing stability

Description : In the illustrated amplifier, the RESET potentiometer A1R2 sets the stability of the control loop by changing the reset time constant. As the potentiometer is turned clockwise _________. EL-0060 A. ... is increased to the summing point at terminal 5 D. response time is increased decreasing stability

Last Answer : Answer: B

To determine the state of charge of a nickel-cadmium battery, you would use a/an _____________. A. voltmeter B. hydrometer C. ammeter D. potentiometer

Description : To determine the state of charge of a nickel-cadmium battery, you would use a/an _____________. A. voltmeter B. hydrometer C. ammeter D. potentiometer

Last Answer : Answer: A

As shown in the illustrations, ordered rudder angle is fed back from the ________________. EL-0097 A. power unit to the magnetic amplifier B. steering gear to the control potentiometer C. magnetic amplifier to the steering gear D. rudder yoke to the non-followup controller

Description : As shown in the illustrations, ordered rudder angle is fed back from the ________________. EL-0097 A. power unit to the magnetic amplifier B. steering gear to the control potentiometer C. magnetic amplifier to the steering gear D. rudder yoke to the non-followup controller

Last Answer : Answer: A

If Relay #5 changed contact position grounding the 'auto' input to the 'pitch controller module', pitch control would be effected by the _________________. EL-0095 A. pitch feedback potentiometer B. Engine room thrust split potentiometer C. Engine room thrust lever only D. Bridge thrust lever only

Description : If Relay #5 changed contact position grounding the 'auto' input to the 'pitch controller module', pitch control would be effected by the _________________. EL-0095 A. pitch feedback potentiometer B. Engine room thrust split potentiometer C. Engine room thrust lever only D. Bridge thrust lever only

Last Answer : Answer: B

As shown in the two illustrations for 'pitch control' and engine speed control', when the plant is in 'AUTO / CRUISE' propeller pitch is controlled by ___________. EL-0095 A. the 'trim potentiometer' and speed by either 'thrust lever' B. either 'thrust lever' and speed also by the selected Lever C. the split trim potentiometer and speed by its 'trim pot'. D. either 'thrust lever' and speed by the 'trim potentiometer'

Description : As shown in the two illustrations for 'pitch control' and engine speed control', when the plant is in 'AUTO / CRUISE' propeller pitch is controlled by ___________. EL-0095 A. the 'trim potentiometer' and ... and speed by its 'trim pot'. D. either 'thrust lever' and speed by the 'trim potentiometer'

Last Answer : Answer: D

The 'pitch controller module' shown in the illustration is fed the actual pitch position of the propeller from the _____________. EL-0095 A. 'pitch meter' B. 'pitch feedback potentiometer' C. #5 relay position D. pitch error signal

Description : The 'pitch controller module' shown in the illustration is fed the actual pitch position of the propeller from the _____________. EL-0095 A. 'pitch meter' B. 'pitch feedback potentiometer' C. #5 relay position D. pitch error signal

Last Answer : Answer: B

A suspected 'open' in a motor field can be tested by using a/an ____________. A. potentiometer B. megger C. wattmeter D. ammeter

Description : A suspected 'open' in a motor field can be tested by using a/an ____________. A. potentiometer B. megger C. wattmeter D. ammeter

Last Answer : Answer: B