For measurements on high voltage capacitors, the suitable bridge is?

by

1 Answer

Answer :

For measurements on high voltage capacitors, the suitable bridge is Schering bridge.

by

Related questions

The voltage drop, for constant voltage transmission is compensated by installing (a) inductors (b) capacitors (c) synchronous motors (d) all of above (e) none of the above

Description : The voltage drop, for constant voltage transmission is compensated by installing (a) inductors (b) capacitors (c) synchronous motors (d) all of above (e) none of the above

Last Answer : (c) synchronous motors

Series capacitors on transmission lines are of little use when the load VAR requirement is (a) large (b) small (b) fluctuating (d) any of the above

Description : Series capacitors on transmission lines are of little use when the load VAR requirement is (a) large (b) small (b) fluctuating (d) any of the above

Last Answer : (b) small

In a substation the following equipment is not installed (a) exciters (b) series capacitors (c) shunt reactors (d) voltatre transformers

Description : In a substation the following equipment is not installed (a) exciters (b) series capacitors (c) shunt reactors (d) voltatre transformers

Last Answer : (a) exciters

Which capacitors are suitable for DC filter circuits?

Description : Which capacitors are suitable for DC filter circuits?

Last Answer : Electrolytic capacitors are suitable for DC filter circuits.

In a tap changing transformer, the tappings are provided on (a) primary winding (b) secondary winding (c) high voltage winding (d) any of the above

Description : In a tap changing transformer, the tappings are provided on (a) primary winding (b) secondary winding (c) high voltage winding (d) any of the above

Last Answer : (b) secondary winding

The power transmitted will be maximum when (a) corona losses are minimum (b) reactance is high (c) sending end voltage is more (d) receiving end voltage is more

Description : The power transmitted will be maximum when (a) corona losses are minimum (b) reactance is high (c) sending end voltage is more (d) receiving end voltage is more

Last Answer : (c) sending end voltage is more

The material generally used for armour of high voltage cables is (a) aluminium (b) steel (c) brass (d) copper

Description : The material generally used for armour of high voltage cables is (a) aluminium (b) steel (c) brass (d) copper

Last Answer : (b) steel

The material commonly used for insulation in high voltage cables is (a) lead (b) paper (c) rubber (d) none of the above

Description : The material commonly used for insulation in high voltage cables is (a) lead (b) paper (c) rubber (d) none of the above

Last Answer : (b) paper

High voltage transmission lines use (a) suspension insulators (b) pin insulators (c) both (a) and (b) (d) none of the above

Description : High voltage transmission lines use (a) suspension insulators (b) pin insulators (c) both (a) and (b) (d) none of the above

Last Answer : (a) suspension insulators

Most of the high voltage transmission lines in India are (a) underground (b) overhead (c) either of the above (d) none of the above

Description : Most of the high voltage transmission lines in India are (a) underground (b) overhead (c) either of the above (d) none of the above

Last Answer : (b) overhead

State the advantages of use of high voltage in transmission of Electric power.

Description : State the advantages of use of high voltage in transmission of Electric power. 

Last Answer : Advantages: 1. As Transmission voltage increases, current decreases. 2. As current decreases, cross section of conductor decreases. 3. As cross section of conductor decreases, its ... high voltage transmission line, successful interconnection of transmission line is possible than low voltage. 

Limitation and application of High Voltage DC (HVDC)

Description : Limitation and application of High Voltage DC (HVDC)

Last Answer : Limitation and application of High Voltage DC (HVDC) :  Limitation:- 1) It is difficult to step up and step down DC voltage like AC voltage. 2) Special cooling ... conventional/non-conventional) 12) Increasing existing grid utilization. 13) Interconnection of different grids or networks

Step-down transformer converts high voltage and low current into:

Description : Step-down transformer converts high voltage and low current into:  (A) How voltage and high current (B) High voltage and low current (C) Low voltage and high current (D) None of the above

Last Answer : Step-down transformer converts high voltage and low current into: Low voltage and high current

The contacts of high voltage switches used in power system are submerged in oil. The main purpose of the oil is to?

Last Answer : The contacts of high voltage switches used in power system are submerged in oil. The main purpose of the oil is to extinguish the arc.

Why is it cheaper to transmit electrical energy at high voltage?

Description : Why is it cheaper to transmit electrical energy at high voltage?

Last Answer : Because of the electrical energy was step upped by transformers the transformer have high efficiency than the electric energy is cheaper

What is meant by extra high voltage transmission?

Description : What is meant by extra high voltage transmission?

Last Answer : HT & LT  two types transmission in industrial line 

Why high voltage can reduce power loss?

Description : Why high voltage can reduce power loss?

Last Answer : when voltage has increased due to reduced current flow, thus power loss given by ( I^2R) will be low due to reduced current(I^2) provided that resistance (R) is constant.

Why high voltage is used in power transmission?

Description : Why high voltage is used in power transmission?

Last Answer : The primary reason that power is transmitted at high voltages is to increase efficiency. ... The lower current that accompanies high voltage transmissionreduces resistance in the conductors aselectricity flows ... This means that thin, light-weight wires can beused in long-distance transmission.

What are the advantages of high voltage transmission?

Description : What are the advantages of high voltage transmission?

Last Answer : Advantages:  1. As Transmission voltage increases, current decreases. 2. As current decreases, cross section of conductor decreases. 3. As cross section of conductor decreases ... line increases  12. As transmission voltage increases power handling capacity of transmission line increases 

does the high voltage side of Transformer winding have more number of turns?

Last Answer : yes High Voltage side of Transformer winding have more number of turns. and low voltage side of Transformer winding have less number of turns.

Why does surge impedance loading (SIL) increase with increase in voltage level?

Description : Why does surge impedance loading (SIL) increase with increase in voltage level?

Last Answer : Answer: SIL varies as the square of the operating voltage, so SIL increases with increase in voltage level

Electro-mechanical voltage regulators are generally used in (a) reactors (b) generators (c) transformers (d) all of the above

Description : Electro-mechanical voltage regulators are generally used in (a) reactors (b) generators (c) transformers (d) all of the above

Last Answer : (b) generators

When an alternator connected to the bus-bar is shut down the bus-bar voltage will (a) fall (b) rise (c) remain unchanged (d) none of the above

Description : When an alternator connected to the bus-bar is shut down the bus-bar voltage will (a) fall (b) rise (c) remain unchanged (d) none of the above

Last Answer : (c) remain unchanged

The frequency of voltage generated, in case of generators, can be increased by (a) using reactors (b) increasing the load (c) adjusting the governor (d) reducing the terminal voltage (e) none of the above

Description : The frequency of voltage generated, in case of generators, can be increased by (a) using reactors (b) increasing the load (c) adjusting the governor (d) reducing the terminal voltage (e) none of the above

Last Answer : (c) adjusting the governor

When the interconnector between two stations has large reactance (a) the transfer of power will take place with voltage fluctuation and noise (b) the transfer of power will take place with least loss (c) the stations will fall out of step be¬cause of large angular displacement between the stations (d) none of the above

Description : When the interconnector between two stations has large reactance (a) the transfer of power will take place with voltage fluctuation and noise (b) the transfer of power will take place with least loss ... out of step be¬cause of large angular displacement between the stations (d) none of the above

Last Answer : (c) the stations will fall out of step be¬cause of large angular displacement between the stations

For transmission of power over a distance of 500 km, the transmission voltage should be in the range (a) 150 to 220 kV (b) 100 to 120 kV (c) 60 to 100 kV (d) 20 to 50 kV

Description : For transmission of power over a distance of 500 km, the transmission voltage should be in the range (a) 150 to 220 kV (b) 100 to 120 kV (c) 60 to 100 kV (d) 20 to 50 kV

Last Answer : (a) 150 to 220 kV

Constant voltage transmission entails the following disadvantage (a) large conductor area is required for same power transmission (b) short-circuit current of the system is increased (c) either of the above (d) none of the above

Description : Constant voltage transmission entails the following disadvantage (a) large conductor area is required for same power transmission (b) short-circuit current of the system is increased (c) either of the above (d) none of the above

Last Answer : (b) short-circuit current of the system is increased

Which of the following equipment, for regulating the voltage in distribution feeder, will be most economical ? (a) Static condenser (b) Synchronous condenser (c) Tap changing transformer (d) Booster transformer

Description : Which of the following equipment, for regulating the voltage in distribution feeder, will be most economical ? (a) Static condenser (b) Synchronous condenser (c) Tap changing transformer (d) Booster transformer

Last Answer : (d) Booster transformer

For transmission of power over a distance of 200 km, the transmission voltage should be (a) 132 kV (b) 66 kV (c) 33 kV (d) 11 kV

Description : For transmission of power over a distance of 200 km, the transmission voltage should be (a) 132 kV (b) 66 kV (c) 33 kV (d) 11 kV

Last Answer : (a) 132 kV

By which of the following a bus-bar is rated ? (a) Current only (b) Current and voltage (c) Current, voltage and frequency (d) Current, voltage, frequency and short time current

Description : By which of the following a bus-bar is rated ? (a) Current only (b) Current and voltage (c) Current, voltage and frequency (d) Current, voltage, frequency and short time current

Last Answer : (d) Current, voltage, frequency and short time current

Transmission voltage of ll kV is normally used for distances upto (a) 20—25 km (b) 40—50 km (c) 60—70 km (d) 80—100 km

Description : Transmission voltage of ll kV is normally used for distances upto (a) 20—25 km (b) 40—50 km (c) 60—70 km (d) 80—100 km

Last Answer : (a) 20—25 km

Which of the following is usually not the generating voltage ? (a) 6.6 kV (b) 8.8 kV (c) 11 kV (d) 13.2 kV

Description : Which of the following is usually not the generating voltage ? (a) 6.6 kV (b) 8.8 kV (c) 11 kV (d) 13.2 kV

Last Answer : (b) 8.8 kV

As compared to a 2-wire D.C. distributor, a 3-wire distributor with same maximum voltage to earth uses only (a) 31.25 percent of copper (b) 33.3 percent of copper (c) 66.7 percent of copper (d) 125 percent of copper

Description : As compared to a 2-wire D.C. distributor, a 3-wire distributor with same maximum voltage to earth uses only (a) 31.25 percent of copper (b) 33.3 percent of copper (c) 66.7 percent of copper (d) 125 percent of copper

Last Answer : (a) 31.25 percent of copper

Transmitted power remaining the same, if supply voltage of a D.C. 2-wire feeder is increased 100 percent, saving in copper is (a) 25 percent (b) 50 percent (c) 75 percent (d) 100 percent

Description : Transmitted power remaining the same, if supply voltage of a D.C. 2-wire feeder is increased 100 percent, saving in copper is (a) 25 percent (b) 50 percent (c) 75 percent (d) 100 percent

Last Answer : (b) 50 percent

The voltage of the single phase supply to residential consumers is (a) 110 V (b) 210 V (c) 230 V (d) 400 V

Description : The voltage of the single phase supply to residential consumers is (a) 110 V (b) 210 V (c) 230 V (d) 400 V

Last Answer : (c) 230 V

Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at the line terminals (c) Possibility of better protection for the line due to possible use of higher terminal reactants (d) Improvement of power factor at times of moderate and heavy loads (e) Possibility of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Description : Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at ... of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Last Answer : (a) Increase of short-circuit current of the system

The phenomenon qf rise in voltage at the receiving end of the open-circuited or lightly loaded line is called the (a) Seeback effect (b) Ferranti effect (c) Raman effect (d) none of the above

Description : The phenomenon qf rise in voltage at the receiving end of the open-circuited or lightly loaded line is called the (a) Seeback effect (b) Ferranti effect (c) Raman effect (d) none of the above

Last Answer : (b) Ferranti effect

A dummy strain gage is used in a quarter bridge strain gage circuit to :

Description : A dummy strain gage is used in a quarter bridge strain gage circuit to :  (A) compensate for changes in temperature and lead wire resistance  (B) produce more output voltage from the bridge  (C) increase the sensitivity of the bridge  (D) compensate lead wire resistance only

Last Answer : A dummy strain gage is used in a quarter bridge strain gage circuit to : compensate for changes in temperature and lead wire resistance 

The bridge method commonly used for finding mutual inductance is

Description : The bridge method commonly used for finding mutual inductance is (A) Heaviside Campbell bridge (B) Schering bridge (C) De Sauty bridge (D) Wien bridge

Last Answer : The bridge method commonly used for finding mutual inductance is Heaviside Campbell bridge

The bridge most suited for measurement of a four-terminal resistance in the range of 0.001 Ohm to 0.1 Ohm

Description : The bridge most suited for measurement of a four-terminal resistance in the range of 0.001 Ohm to 0.1 Ohm (A) Wien’s bridge (B) Kelvin double bridge (C) Maxwell’s bridge (D) Shering Bridge

Last Answer : The bridge most suited for measurement of a four-terminal resistance in the range of 0.001 Ohm to 0.1 Ohm (A) Wien’s bridge (B) Kelvin double bridge (C) Maxwell’s bridge (D) Shering Bridge

If an inductance is connected in one arm of bridge and resistances in the remaining three arms?

Last Answer : If an inductance is connected in one arm of bridge and resistances in the remaining three arms the bridge cannot be balanced.

In a Schering bridge the potential of the detector above earth potential is?

Last Answer : In a Schering bridge the potential of the detector above earth potential is a few volts only.

In an Anderson bridge, the unknown inductance is measured in terms of?

Last Answer : In an Anderson bridge, the unknown inductance is measured in terms of known capacitance and resistance.

A universal RLC bridge uses?

Description : A universal RLC bridge uses?

Last Answer : A universal RLC bridge uses Maxwell Wein bridge for measurement of inductance and modified De Santy's bridge for measurement of capacitance.

Capacitors

Description : Capacitors

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Why capacitors are used to improve power factor?

Description : Why capacitors are used to improve power factor?

Last Answer :  Capacitors generate reactive power instead of that drawn from source which is required by inductive loads.so it reduce the reactive current which is drawn from source to be drawn from capacitor.This control in Electric bills cost.

State any four types of capacitors.

Description : State any four types of capacitors.

Last Answer : Types of capacitors: i) Air capacitor ii) Paper capacitor iii) Mica capacitor iv) Ceramic capacitor v) Electrolytic capacitor vi) Poly-carbon capacitor

What is the charge on each capacitor when a 150 V is applied across two capacitors with values 5 μF and 10 μF,

Description : What is the charge on each capacitor when a 150 V is applied across two capacitors with values 5 μF and 10 μF, connected in series? A) 500 μC B) 0.5 μC C) 0.5 C D) None of these

Last Answer : What is the charge on each capacitor when a 150 V is applied across two capacitors with values 5 μF and 10 μF, connected in series? A) 500 μC B) 0.5 μC C) 0.5 C D) None of these

The circuit has resistors, capacitors and semi-conductor diodes. The circuit will be known as?

Description : The circuit has resistors, capacitors and semi-conductor diodes. The circuit will be known as

Last Answer : The circuit has resistors, capacitors and semi-conductor diodes. The circuit will be known as non-linear circuit.

Capacitors for power factor correction are rated in?

Description : Capacitors for power factor correction are rated in?

Last Answer : Capacitors for power factor correction are rated in kVAR.