A sensitive galvanometer produces large deflection for a?

by

1 Answer

Answer :

A sensitive galvanometer produces large deflection for a small value of current.

by

Related questions

Most sensitive galvanometer is?

Last Answer : Most sensitive galvanometer is spot ballistic galvanometer.

Damping of the Ballistic galvanometer is made small to?

Last Answer : Damping of the Ballistic galvanometer is made small to get first deflection large.

vertical deflection system and explain its operation.

Description : vertical deflection system and explain its operation.

Last Answer : The main function of the vertical deflection system , is to provide an amplified signal of proper level to derive the vertical deflection plates without any distortion. For amplification of the ... suppression, reduced nonlinear effects because none of the plates are at ground potential.

The vertical deflection of an electron beam on the screen of a CRO is measured to be 8 mm. Now, the

Description : The vertical deflection of an electron beam on the screen of a CRO is measured to be 8 mm. Now, the potential difference between the Y-plates is doubled, and simultaneously the pre-accelerating anode voltage is reduced to half of ... on the screen would become (A) 64 mm (B) 32 mm (C) 8 mm (D) 1 mm

Last Answer : The vertical deflection of an electron beam on the screen of a CRO is measured to be 8 mm. Now, the potential difference between the Y-plates is doubled, and simultaneously the pre-accelerating ... of its previous value. Then, the vertical deflection of the beam on the screen would become 32 mm

Usually wide and sensitive speed control is desired in case of?

Last Answer : Usually wide and sensitive speed control is desired in case of colliery winders.

How to Shrink Large Pores

Description : How to Shrink Large Pores

Last Answer : How to Shrink Large Pores Large pores can be a hassle, especially in a world full of airbrushed models with no visible pores filling our magazine pages. Large pores can also lead to a tendency ... add calamine or sandalwood powder to the tomato juice before applying. Rinse it off with warm water.

A large AC generator, supplying power to an infinite bus, has a sudden short-circuit occurring at its terminals

Description : A large AC generator, supplying power to an infinite bus, has a sudden short-circuit occurring at its terminals. Assuming the prime mover input and the voltage behind the transient reactance to remain constant immediately after the fault, acceleration of the generator rotor is

Last Answer : A large AC generator, supplying power to an infinite bus, has a sudden short-circuit occurring at its terminals. Assuming the prime mover input and the voltage behind the transient reactance ... , acceleration of the generator rotor is inversely proportional to the moment of inertia of the machine

Large capacity generators are invariably?

Last Answer : Large capacity generators are invariably hydrogen cooled.

Interruption of large currents by relay requires?

Last Answer : Interruption of large currents by relay requires arc suppressing blow out coils, wide separation of the opened contacts, high speed opening of contacts.

In a galvanometer, the deflection becomes one half when the galvanometer is shunted by a 20 ohm resistor.

Description : In a galvanometer, the deflection becomes one half when the galvanometer is shunted by a 20 ohm resistor. The galvanometer resistance is 

Last Answer : In a galvanometer, the deflection becomes one half when the galvanometer is shunted by a 20 ohm resistor. The galvanometer resistance is 10 Ohm

In a moving coil galvanometer, the deflection of the coil q is related to the electrical current i by the relation

Description : In a moving coil galvanometer, the deflection of the coil q is related to the electrical current i by the relation

Last Answer : In a moving coil galvanometer, the deflection of the coil q is related to the electrical current i by the ... theta^(2)` D. `I prop sqrt(theta)`

A galvanometer having resistance of `50 Omega` requires a current of `100 Omega A` to given full scale deflection. How much resistance is required to

Description : A galvanometer having resistance of `50 Omega` requires a current of `100 Omega A` to given full scale deflection. How much resistance is required to

Last Answer : A galvanometer having resistance of `50 Omega` requires a current of `100 Omega A` to given full scale ... in series D. `10^(5)Omega` in parallel

A galvanometer has a coil of resistance `100 Omega` and gives a full-scale deflection for `30 mA` current. If it is to work as a voltmeter of `30 V` r

Description : A galvanometer has a coil of resistance `100 Omega` and gives a full-scale deflection for `30 mA` current. If it is to work as a voltmeter of `30 V` r

Last Answer : A galvanometer has a coil of resistance `100 Omega` and gives a full-scale deflection for `30 mA` current. ... Omega` C. `1000 Omega` D. `1800 Omega`

A galvanometer having internal resistance `10 Omega` required `0.01` A for a full scale deflection. To convert this galvanometer to a voltmeter of ful

Description : A galvanometer having internal resistance `10 Omega` required `0.01` A for a full scale deflection. To convert this galvanometer to a voltmeter of ful

Last Answer : A galvanometer having internal resistance `10 Omega` required `0.01` A for a full scale deflection. ... Omega` in series D. `12010 Omega` in parallel

A galvanometer of resistance `50 Omega` is connected to a battery of 8 V along with a resistance of `3950 Omega` in series. A full scale deflection of

Description : A galvanometer of resistance `50 Omega` is connected to a battery of 8 V along with a resistance of `3950 Omega` in series. A full scale deflection of

Last Answer : A galvanometer of resistance `50 Omega` is connected to a battery of 8 V along with a resistance of `3950 Omega ... `. A. 1950 B. 7900 C. 2000 D. 7950

A galvanometer of resistance `50 Omega ` is connected to a battery of `3 V` along with resistance of `2950 Omega` in series. A full scale deflection o

Description : A galvanometer of resistance `50 Omega ` is connected to a battery of `3 V` along with resistance of `2950 Omega` in series. A full scale deflection o

Last Answer : A galvanometer of resistance `50 Omega ` is connected to a battery of `3 V` along with resistance of `2950 ... `Omega` C. 5550 `Omega` D. 6050 `Omega`

In a potentiometer experiment, the galvanometer shows no deflection when a cell is connected across `60 cm` of the potentiometer wire. If the cell is

Description : In a potentiometer experiment, the galvanometer shows no deflection when a cell is connected across `60 cm` of the potentiometer wire. If the cell is

Last Answer : In a potentiometer experiment, the galvanometer shows no deflection when a cell is connected across `60 cm` of ... ` C. `1.2Omega` D. `1.5Omega`

`AB` is a wire of uniform resistance. The galvanometer `G` shows no deflection when the length `AC = 20 cm` and `CB = 80 cm`. The resistance `R` is eq

Description : `AB` is a wire of uniform resistance. The galvanometer `G` shows no deflection when the length `AC = 20 cm` and `CB = 80 cm`. The resistance `R` is eq

Last Answer : `AB` is a wire of uniform resistance. The galvanometer `G` shows no deflection when the length `AC = 20 cm ... ` B. `8Omega` C. `20Omega` D. `40Omega`

Why galvanometer show opposite deflection?

Description : Why galvanometer show opposite deflection?

Last Answer : What is the answer ?

A galvanometer with 20 ohms coil resistence has a full-scale deflection of 10 mA. A 0.02 ohm is placed across the meter to increase its rating capacity. What is the new full scale current for the meter?

Description : A galvanometer with 20 ohms coil resistence has a full-scale deflection of 10 mA. A 0.02 ohm is placed across the meter to increase its rating capacity. What is the new full scale current for the meter?

Last Answer : False.

The current I passing through the galvanometer coil is related to the angle of deflection θ as a) I ∝ θ b) I 1/∝ θ c) I ∝ θ 2 d) I 1/∝ θ 2

Description : The current I passing through the galvanometer coil is related to the angle of deflection θ as a) I ∝ θ b) I 1/∝ θ c) I ∝ θ 2 d) I 1/∝ θ 2

Last Answer : a) I ∝ θ

A galvanometer of 65 Ω resistance gives full scale deflection with 4 mA current. In order to convert it into ammeter, the range of 10 A is connected with it, the shunt resistance should be a) 0.1 Ω b) 0.2 Ω c) 0.06 Ω d) 0.03 Ω

Description : A galvanometer of 65 Ω resistance gives full scale deflection with 4 mA current. In order to convert it into ammeter, the range of 10 A is connected with it, the shunt resistance should be a) 0.1 Ω b) 0.2 Ω c) 0.06 Ω d) 0.03 Ω

Last Answer : d) 0.03 Ω

When measuring insulation resistance of cables using d.c. source, the galvanometer used should be initially

Description : When measuring insulation resistance of cables using d.c. source, the galvanometer used should be initially short circuited because  (A) Cables have a low value of capacitance which draws a high ... high value of charging current (D) Cables have a low value of capacitance and initial resistance

Last Answer : When measuring insulation resistance of cables using d.c. source, the galvanometer used should be initially short circuited because Cables have a high value of capacitance which draws a high value of charging current

A galvanometer has

Last Answer : A galvanometer has Eddy current damping.

In a ballistic galvanometer, the deflecting torque is proportional to

Last Answer :  In a ballistic galvanometer, the deflecting torque is proportional to the current through coil.

An Aryton shunt is used to make a D'Arsonval galvanometer into a

Last Answer : An Aryton shunt is used to make a D'Arsonval galvanometer into a multi range ammeter.

While testing cables the galvanometer used should be initially ...

Description : While testing cables the galvanometer used should be initially short-circuited in order to protect it from sudden initial inrush currents as the cable have:

Last Answer : While testing cables the galvanometer used should be initially short-circuited in order to protect it from sudden initial inrush currents as the cable have: A high value of initial capacitance

A ballistic galvanometer is used to measure:

Last Answer : A ballistic galvanometer is used to measure: Charge

The ballistic galvanometer is usually lightly damped so that:

Last Answer : The ballistic galvanometer is usually lightly damped so that: Amplitude of the first swing is large.

A 0-10 A ammeter has a guaranteed accuracy of 1% of full scale deflection, the limiting error while reading

Description : A 0-10 A ammeter has a guaranteed accuracy of 1% of full scale deflection, the limiting error while reading 2.5 A will be (a) 1% (b) 2% (c) 4% (d) None of these 

Last Answer : A

A permanent magnet moving coil ammeter has a coil resistance of 99 ohm and Full Scale Deflection (FSD)

Description : A permanent magnet moving coil ammeter has a coil resistance of 99 ohm and Full Scale Deflection (FSD) current of 0.1mA. Shunt resistance is 1 ohm. Current through the meter at 0.5 F.S.D is:

Last Answer : A permanent magnet moving coil ammeter has a coil resistance of 99 ohm and Full Scale Deflection (FSD) current of 0.1mA. Shunt resistance is 1 ohm. Current through the meter at 0.5 F.S.D is: 0.05mA

A moving coil instrument has a resistance of 10 W and gives full scale deflection when carrying

Description : A moving coil instrument has a resistance of 10 W and gives full scale deflection when carrying a current of 50 mA. To measure current upto 100 A, we will have to connect • 10 W resistance in series • 10 W resistance in parallel • 10/1999 W resistance in series • 10/1999 W resistance in parallel

Last Answer : A moving coil instrument has a resistance of 10 W and gives full scale deflection when carrying a current of 50 mA. To measure current upto 100 A, we will have to connect 10/1999 W resistance in parallel

In a gravity controlled instrument, the deflection angle is proportional to

Last Answer :  In a gravity controlled instrument, the deflection angle is proportional to sine inverse of measurand.

The full-scale deflection current of an ammeter is 1 mA and its internal resistance is 100Ohm. ...

Description : The full-scale deflection current of an ammeter is 1 mA and its internal resistance is 100Ohm. This is to have full deflection when 100V is measured. What is the value of series resistor to be used?

Last Answer : The full-scale deflection current of an ammeter is 1 mA and its internal resistance is 100Ohm. This is to have full deflection when 100V is measured. 99.99 K ohms is the value of series resistor to be used.

The full-scale deflection current of an ammeter is 1 mA and its internal...

Description :  The full-scale deflection current of an ammeter is 1 mA and its internal resistance is 100Ohm. If this meter is to have full deflection at 5A, what is the value of the shunt resistance to be used?

Last Answer :  The full-scale deflection current of an ammeter is 1 mA and its internal resistance is 100Ohm. If this meter is to have full deflection at 5A, 1/49.99 ohms is the value of the shunt resistance to be used.

In a free running oscilloscope the horizontal deflection system is driven by a ........waveform

Last Answer :  In a free running oscilloscope, the horizontal deflection system is driven by a Ramp waveform

The instrument having its deflection depends upon average value is:

Last Answer : The instrument having its deflection depends upon average value is:  Rectifier type

If two meters X and Y requires 40mA and 50mA respectively, to give full scale deflection, then:

Last Answer : If two meters X and Y requires 40mA and 50mA respectively, to give full scale deflection, then: X is more sensitive

The deflection of hot-wire instrument depends on:

Last Answer : The deflection of hot-wire instrument depends on: RMS value of the alternating current

Rotor shaft of a large electric motor supported between short bearings at both ends shows a deflection of 1.8 mm in middle of motor. Assuming rotor to be perfectly balanced and supported at knife edges at both ends, likely critical speed (rpm) of shaft isA 350 B 4430 C 705 D 2810

Description : Rotor shaft of a large electric motor supported between short bearings at both ends shows a deflection of 1.8 mm in middle of motor. Assuming rotor to be perfectly balanced and supported at knife edges at both ends, likely critical speed (rpm) of shaft isA 350 B 4430 C 705 D 2810

Last Answer : C 705

Deflection in a spring should be (a) Large (b) Small (c) Zero (d) None

Description : Deflection in a spring should be (a) Large (b) Small (c) Zero (d) None

Last Answer : (a) Large

Deflection in a spring should be (a) Large (b) Small (c) Zero (d) None

Description : Deflection in a spring should be (a) Large (b) Small (c) Zero (d) None

Last Answer : (a) Large

Deflection in a spring should be (a) Large (b) Medium (c) Small (d) None

Description : Deflection in a spring should be (a) Large (b) Medium (c) Small (d) None

Last Answer : (a) Large

In ______ machines, the size of the shaft is decided by the critical speed which depends on the deflection of the shaft. (a) small (b) medium (c) large (d) any of the above.

Description : In ______ machines, the size of the shaft is decided by the critical speed which depends on the deflection of the shaft. (a) small (b) medium (c) large (d) any of the above.

Last Answer : (c) large

Gas thermometers are more sensitive than the liquid thermometers because the gases – (1) have large coefficient of expansion (2) are lighter (3) have low specific heat (4) have high specific heat

Description : Gas thermometers are more sensitive than the liquid thermometers because the gases – (1) have large coefficient of expansion (2) are lighter (3) have low specific heat (4) have high specific heat

Last Answer : (1) have large coefficient of expansion Explanation: Gases are more sensitive to the temperature than liquids (such as mercury). That means gas expands more than the mercury for the same increase of temperature. Hence the has thermometer is more sensitive than liquid (mercury) thereto-meter.

Gas thermometers are more sensitive than the liquid thermometers because of the gases - (1) have low specific heat (2) have high specific heat (3) have large coefficient of expansion (4) are lighter

Description : Gas thermometers are more sensitive than the liquid thermometers because of the gases - (1) have low specific heat (2) have high specific heat (3) have large coefficient of expansion (4) are lighter

Last Answer : (1) have low specific heat Explanation: Gas thermometers are more sensitive because gas has low specific heat than liquids.

Gas thermometers are more sensitive than the liquid thermometers because the gases (1) have large coefficient of expansion (2) are lighter (3) have low specific heat (4) have high,specific heat

Description : Gas thermometers are more sensitive than the liquid thermometers because the gases (1) have large coefficient of expansion (2) are lighter (3) have low specific heat (4) have high,specific heat

Last Answer : have large coefficient of expansion

Who invented the galvanometer ?

Last Answer : : Discovered Galvanometer (Under Mary Ampere)

Assertion current sensitivity of a galvanometer is directley proportionall to the current through the coil. Reason Voltage sensitivity is inversely pr

Description : Assertion current sensitivity of a galvanometer is directley proportionall to the current through the coil. Reason Voltage sensitivity is inversely pr

Last Answer : Assertion current sensitivity of a galvanometer is directley proportionall to the current ... sensitivity is inversely proportional to voltage.

The coil of a moving coil galvanometer has an effective area of 4xx10^(-2)m^(2)`. It is suspended in a magnetic field of `5xx10^(-2)` Wb `m^(-2)`. If

Description : The coil of a moving coil galvanometer has an effective area of 4xx10^(-2)m^(2)`. It is suspended in a magnetic field of `5xx10^(-2)` Wb `m^(-2)`. If

Last Answer : The coil of a moving coil galvanometer has an effective area of 4xx10^(-2)m^(2)`. It is suspended in a ... D. current sensitivity is `40 deg` `A^(-1)`