In a pure resistive circuit?

In a pure resistive circuit?

In a pure resistive circuit current is in phase with the voltage.

Related questions

Description : In a pure resistive circuit, the average power Pavg is ______ the peak power Pmax. (1) Double (2) One-half of (3) One-fourth (4) Equal to

Last Answer : In a pure resistive circuit, the average power Pavg is One-half of the peak power Pmax.

Description : What is the power factor of purely resistive circuit.

Last Answer : Unity that is 1

Description : In a pure capacitive circuit if the supply frequency is reduced to 1/2, the current will?

Last Answer : In a pure capacitive circuit if the supply frequency is reduced to 1/2, the current will be reduced by half.

Description : In a pure inductive circuit if the supply frequency is reduced to 1/2, the current will?

Last Answer : In a pure inductive circuit if the supply frequency is reduced to 1/2, the current will be doubled.

Description : Pure inductive circuit takes power from the A.C. line when?

Last Answer : It takes power when voltage decreases and current increases.

Description : In a pure inductive circuit?

Last Answer : Voltage lagging in inductor

Description : Pure inductive circuit?

Last Answer : Pure inductive circuit takes power from the line during some part of the cycle and then returns back to it during other part of the cycle.

Description : Give the circuit analysis of current source inverter with resistive load. What are the main difference between voltage source inverter and current source inverter?

Last Answer : Current source inverter (CSI): In current source inverter, the output current is independent of load. The input current of current source inverter is constant. Current source converter converts DC input current to ... are connected in parallel. In CSI diodes are connected in series.

Description : A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is :

Last Answer : A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is : 200 V

Description : Single-phase Midpoint controlled rectifier with Resistive load

Last Answer : Single-phase Midpoint controlled rectifier with Resistive load:  1) During positive half cycle of AC supply, a is positive with respect to b , this makes T1 forward biased and T2 is reverse ... voltage reverses the polarity and T2 is turned off. The operation is as shown in waveforms.

Description : An A.C. voltage is impressed across a pure resistance of 3.5 ohms in parallel with a pure inductance of impedance of 3.5 ohms?

Last Answer : An A.C. voltage is impressed across a pure resistance of 3.5 ohms in parallel with a pure inductance of impedance of 3.5 ohms, both resistance and inductance carry equal currents.

Description : The r.m.s. value of pure cosine function is?

Last Answer : 0.707 of peak value

Description : Pure substances

Last Answer : Any material that is not a mixture, is called a pure substance. Pure substances include elements and compounds. It is much more difficult to break down pure substances into their parts, and complex chemical methods are needed to do this.

Description : A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is (A) 300 W (B) 150 W (C) 45 W (D) 20 W

Last Answer : A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is 150 W

Description : At ______ frequencies the parallel R-L circuit behaves as purely resistive.

Last Answer : At very high frequencies the parallel R-L circuit behaves as purely resistive.

Description : Briefly explain how the power factor of an inductive circuit can be improved.

Last Answer : As we know that power factor should be corrected to ensure that the current supplied is cost friendly. Meaning the power factor should be around one but not greater than one(0.8-0.9) in a ... an inductive circuit due to the inductive reactance which oppose the change of current in the ac circuit.

Last Answer : It is denoted as τ, tau and has the value of 1/RC. We

Description : role of tuned LC circuit in tuned amplifier.

Last Answer : In order to pick up and amplify the desired radio frequency signal, the resistive load in the audio amplifier is replaced by a tuned circuit (also called a parallel resonant circuit)as shown ... desired radio frequency signal. (ii)Amplification of the selected signal to a suitable voltage level.

Description : State Ohm’s law for electric circuit.

Last Answer : Ohms law -States that the current flows in a circuit is directly proportional to the applied voltage (V) and inversely the proportional resistance provided with the temperature main constant

Description : Define active circuit and passive circuit.

Last Answer : Active circuit: Active Circuit is one which contains at least one source of e.m.f. or energy, is called active circuit.  Passive Circuit: Passive Circuit is one which does not contain any source of e.m.f. or energy in it, is called passive circuit.

Description : Basic Circuit Elements

Last Answer : Req= (1/1200 +1/560 + 1/2.1)^-1        = 2.1 ohms RT= 2.1 + 7.8      = 9.9 ohms IT = V/R = 24/9.9                = 2.4 A Veq= R I =  2.1 2 ... 7.8         = 12.096 w                 = 44.928 w _________________________________________ By: Ellis-Junior Kamatjipose [email protected]

Description : Compare combinational logic circuit and sequential logic circuit

Last Answer : Combinational logic Sequential logic The combinational logic circuit consists of logic gate only Sequential logic circuit consists of combinational logic circuit along with memory for storage of ... , multiplexer, demultiplexer etc E.g. counters, shift registers flip-flop etc

Description : What is unilateral and bilateral circuit?

Last Answer : Unilateral Circuit: If the characteristic (response or behavior) of circuit depends on the direction of flow of current through its elements, then the network is called as a unilateral network.  ... the direction of current through its elements, then the network is called as a bilateral network.

Description : Describe the difference between an open circuit and a short circuit.

Last Answer : Open circuit means the wire is cut meaning power will not flow and close circuit means wire is not cut and hence power will flow.Short circuit is the same as close circuit

Description : Series circuit rules

Last Answer : Series circuit rules

Description : Parallel rc circuit

Last Answer : Parallel rc circuit

Description : Parallel circuit rules

Last Answer : Parallel circuit rules

Description : Source free RL circuit 8

Last Answer : Source free RL circuit 8

Description : Source free RL circuit 7

Last Answer : Source free RL circuit 7

Description : Source free RL circuit 6

Last Answer : Source free RL circuit 6

Description : Source free RC circuit 2

Last Answer : Source free RC circuit 2

Description : Source free RC circuit 3

Last Answer : Source free RC circuit 3

Description : Source free RC circuit 4

Last Answer : Source free RC circuit 4

Description : Source free RC circuit 5

Last Answer : Source free RC circuit 5

Description : Source free RC circuit 6

Last Answer : Source free RC circuit 6

Description : Source free RC circuit 7

Last Answer : Source free RC circuit 7

Description : Source free RC circuit 8

Last Answer : Source free RC circuit 8

Description : Source free RL circuit 1

Last Answer : Source free RL circuit 1

Description : Source free RL circuit 2

Last Answer : Source free RL circuit 2

Description : Source free RL circuit 3

Last Answer : Source free RL circuit 3

Last Answer : Source free RL circuit 4

Last Answer : Source free RL circuit 5

Description : State maximum power transfer theorem for DC circuit.

Last Answer : Maximum power transfer theorem for DC circuit: The maximum power transfer theorem states that the source or a network transfers maximum power to load only when the load resistance is equal ... removed (disconnected) ii) All internal independent sources are replaced by their internal resistances.

Description : Mention the precautions to be taken while connecting CT and PT in the circuit.

Last Answer : Precautions to be taken while using instrument transformers: 1. Secondary of CT is never kept open circuited when it is energized. 2. Secondary of PT is never kept short circuited when it ... of the instrument transformers unless they are properly grounded. 8. Never connect to DC circuits.

Description : List any two methods of reactive power measurement in 3 phase circuit.

Last Answer : Methods of reactive power measurement in 3 phase circuit: (i) Two single phase wattmeter method (ii) One single phase wattmeter method

Description : Define balanced and unbalanced load in three phase circuit.

Last Answer : Balanced Load: When all the imedances of 3 phases are equal in magnitude and of same nature then load is said to be balanced.  Unbalanced Load: When all the imedances of 3 phases are not equal in magnitude and of different nature then load is said to be unbalanced.

Description : Draw the circuit diagram of crystal oscillator and explain its working.

Last Answer : To excite a crystal for operation in the series-resonant mode it may be connected as a series element in a feedback path, the crystal impedance is the smallest and the amount of positive feedback is the largest. ... which is good.  The resonant frequency is given as  Fo = 1/( 2 π √LC )

Description : Draw and explain Hartley Oscillator circuit diagram.

Last Answer : Function of each component: 1. An NPN transistor connected in a common emitter configuration works as the active device in amplifier stage and CE configuration provides 180°phase shift. 2. R1 and R2 ... circuit to the base-emitter circuit.  The frequency of oscillation is given as-

Description : Define- (i) Node (ii) Loop for a DC circuit

Last Answer : Ans: i) Node: A point or junction at which two or more elements of network are connected is called as node. ii) Loop: A closed path for flow of current in an electrical circuit is called loop.