What will be the phase angle between two alternating waves of equal frequency...

What will be the phase angle between two alternating waves of equal frequency, when one wave attains maximum value the other is at zero value ?
by

1 Answer

Answer :

90° will be the phase angle between two alternating waves of equal frequency, when one wave attains maximum value the other is at zero value.

by

Related questions

Two waves of the same frequency have opposite phase when the phase angle between them is?

Description : Two waves of the same frequency have opposite phase when the phase angle between them is?

Last Answer : Two waves of the same frequency have opposite phase when the phase angle between them is 180°.

The product of apparent power and cosine of the phase angle between circuit voltage and current is?

Description : The product of apparent power and cosine of the phase angle between circuit voltage and current is?

Last Answer : In parllpar reasonans RLC circuit the current is

Explain the concept of lagging and leading phase angle by waveform.

Description : Explain the concept of lagging and leading phase angle by waveform.

Last Answer : i) Leading phase angle :  When two ac quantities of same frequency do not attain their respective zero or peak values simultaneously, then the quantities are said to be out-of-phase quantities. The ... Similarly, in the second diagram, the voltage is said to be lagging the current by  Φ.

Phase margin is the amount of angle to make the system

Description : Phase margin is the amount of angle to make the system  (1) Oscillatory (2) Stable (3) Unstable (4) Exponential

Last Answer : Phase margin is the amount of angle to make the system Unstable 

The r.m.s. value of a sinusoidal A.C. current is equal to its value at an angle of______degrees.

Description : The r.m.s. value of a sinusoidal A.C. current is equal to its value at an angle of______degrees.

Last Answer : 45

When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a

Description : When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a load is 30°, the displacement power factor of the rectifier is

Last Answer : When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a load is 30°, the displacement power factor of the rectifier is √3/2

Tangent of angle of friction is equal to?

Description : Tangent of angle of friction is equal to?

Last Answer : Tangent of angle of friction is equal to coefficient of friction.

How to find total impedance Z, current I and Impedance angle ?

Description : How to find total impedance Z, current I and Impedance angle ?

Last Answer : How to find total impedance Z, current I and Impedance angle ?

Define: i) Firing angle ii) Conduction angle

Description : Define: i) Firing angle ii) Conduction angle

Last Answer : i) Firing angle: The firing angle of a thyristor is defined as the angle between the zero crossing of the applied voltage and the instant at which the thyristor is triggered or fired. It is a ... off. It is a measure of the duration for which the thyristor conducts current during each AC cycle.

The power factor angle and torque angle of a salient pole synchronous generator drawing a current of 1.0 pu

Description : The power factor angle and torque angle of a salient pole synchronous generator drawing a current of 1.0 pu from a lagging load are 45o and 15o, respectively. The direct axis and quadrature axis currents, respectively, are (A) 0.5 pu ... pu, 0.5 pu (C) 0.707 pu, 0.707 pu (D) 0.5 pu, 0.5 pu

Last Answer : The power factor angle and torque angle of a salient pole synchronous generator drawing a current of 1.0 pu from a lagging load are 45o and 15o, respectively. The direct axis and quadrature axis currents, respectively, are 0.866 pu, 0.5 pu

Torque angle for the synchronous machine is the angle between

Description : Torque angle for the synchronous machine is the angle between (A) stator magnetic field and rotor magnetic field (B) stator magnetic field and net magnetic field in the air gap (C) rotor magnetic field and net magnetic field in the air gap (D) excitation voltage and impedance voltage drop

Last Answer : Torque angle for the synchronous machine is the angle between rotor magnetic field and net magnetic field in the air gap

Angle of friction is the?

Description : Angle of friction is the?

Last Answer : Angle of friction is the angle between normal reaction and the resultant of normal reaction and the limiting friction.

If the current in a capacitor leads the voltage by 80°, the loss angle of the capacitor is?

Last Answer : If the current in a capacitor leads the voltage by 80°, the loss angle of the capacitor is 10°.

The coupling angle or load angle of synchronous motor is defined as the angle between the?

Last Answer : The coupling angle or load angle of synchronous motor is defined as the angle between the rotor and the stator poles of opposite polarity.

What is meant by firing angle of thyristor?

Description : What is meant by firing angle of thyristor?

Last Answer : The point at which SCR is triggered is known as firings angle of thyristor.

What is the maximum value of torque angle in synchronous motor?

Description : What is the maximum value of torque angle in synchronous motor?

Last Answer : The maximum value of torque angle in synchronous motor is 90 degrees electrical.

The synchronous motor will develop maximum power when the load angle is?

Description : The synchronous motor will develop maximum power when the load angle is?

Last Answer : The synchronous motor will develop maximum power when the load angle is 900.

what is firing angle?

Description : what is firing angle?

Last Answer : Firing angle is time in electrical degrees from the instant the valve voltage is positive to the application of firing pulse to the valve (start of conduction). Also called delay angle.

If two sinusoids of the same frequency but of different amplitudes and phase angles are subtracted, the resultant is?

Last Answer : If two sinusoids of the same frequency but of different amplitudes and phase angles are subtracted, the resultant is a sinusoid of the same frequency.

State the application of phase sequence indicator; clip on ammeter, frequency meter & P.F. meter.

Description : State the application of phase sequence indicator; clip on ammeter, frequency meter & P.F. meter.

Last Answer : Phase Sequence Indicator:  1. For finding correct phase sequence of supply  2. For obtaining exact instant of parallel operation of alternators.  3. For obtaining reversal of rotation ...  4. In electroplating industries   5. In various processes industries for measuring power factor

List any two methods of reactive power measurement in 3 phase circuit.

Description : List any two methods of reactive power measurement in 3 phase circuit.

Last Answer : Methods of reactive power measurement in 3 phase circuit: (i) Two single phase wattmeter method (ii) One single phase wattmeter method

State any two disadvantages of one wattmeter method of measurement of 3 phase power.

Description : State any two disadvantages of one wattmeter method of measurement of 3 phase power.

Last Answer : State any two disadvantages of one wattmeter method of measurement of 3 phase power. Disadvantages of one wattmeter method:- 1. Only used for balanced load 2. It can not be used for ... connection then neutral point must be available 4. Delta connection must be opened to connect current coil.

When the phase difference between two sinusoidal quantities is 90° they are said to be ______

Description : When the phase difference between two sinusoidal quantities is 90° they are said to be ______ A) Phase right angle B) Phase quadrature C) Phase sinuright D) None of these

Last Answer : When the phase difference between two sinusoidal quantities is 90° they are said to be Phase quadrature

Explain MCB and ELCB with connection diagram supplying single phase load.

Description : Explain MCB and ELCB with connection diagram supplying single phase load. 

Last Answer : OR OR Explanation: * MCB provides short circuit protection. * MCB provides overload protection * ELCB provides earth fault protection. * MCB is in series with ... occurs, the ELCB cuts off the power within the time of 0.1 sec. automatically to protect the personnel. 

Why is a capacitor used in a single phase motor and not in three phase motor ?

Description : Why is a capacitor used in a single phase motor and not in three phase motor ?

Last Answer : In 1-phase induction motor capacitor work is generate the auxiliary winding current than excite the main winding to rotor starts rotate. After rotor start rotating about 75% of their speed than auxiliary ... emf to start the motor.so,in 3-phase induction motor is self start induction motor.

Define Amplitude and Phase of Sinusoidal quantity.

Description : Define Amplitude and Phase of Sinusoidal quantity.

Last Answer : Amplitudes are expressed either as instantaneous values or mostly as peak values.  Amplitude is the fluctuation or displacement of a wave from its mean value.  Phase is the position of a ... .  Phase an expression of relative displacement between or among waves having the same frequency . 

working principle of single phase motor

Description : working principle of single phase motor

Last Answer : The Stator of single phase induction motor houses two windings  1. Main (Running) winding 2. Auxiliary (Starting ) winding Rotor of single phase induction motor is ... with starting winding or a capacitor may be permanently connected in series with Auxiliary (Starting ) winding.

Why is a three phase denoted by R, Y, B ?

Description : Why is a three phase denoted by R, Y, B ?

Last Answer : phase 1 ,R =Red colour cable terminal, phase 2 Y=Yellow colour terminal cable,Phase 3 B=Blue colour cable terminal, N =Neutral. For identification.

Explain the working of a single phase capacitor start induction motor.

Description : Explain the working of a single phase capacitor start induction motor. 

Last Answer : Single phase capacitor start induction motor https://youtu.be/31lvvzU5Puc

State any four advantages of three phase induction motor.

Description : State any four advantages of three phase induction motor. 

Last Answer : Advantages of three phase induction motor https://youtu.be/27OIOCKN05U

What is Phase sequence? Draw waveforms of 3 phase emf.

Description : What is Phase sequence? Draw waveforms of 3 phase emf.

Last Answer : Phase sequence: It is the order in which the three phases reach their peak or maximum values. It is shown in below fig. the phase sequence is A-B-C (or R-Y-B). In the following waveforms, it is ... 120º, B- phase voltage attains its positive maximum value. So the phase sequence is R-Y-B. 

Define balanced 3 phase load.

Description : Define balanced 3 phase load.

Last Answer : Balanced 3 phase Load: Balanced three phase load is defined as star or delta connection of three equal impedances having equal real parts and equal imaginary parts. It takes same current of equal magnitude and equal phase angle.

With a neat sketch explain working of 1 phase dynamometer type power factor meter.

Description : With a neat sketch explain working of 1 phase dynamometer type power factor meter.

Last Answer : Working of 1 phase dynamometer type power factor meter : The current coil is connected in series with load. Two pressure coils marked as A and B are connected across the supply terminals ... becomes stationary and the pointer shows steady deflection corresponding to the power factor of the load. 

State the use of:- (i) Clip-on-ammeter (ii) Phase sequence indicator

Description : State the use of:- (i) Clip-on-ammeter (ii) Phase sequence indicator

Last Answer : (i) Clip-on-ammeter: used for measurement of current in cables/lines in live conditions without disconnecting them.  (ii) Phase sequence indicator: To determine /find the phase sequence of 3 phase supply. 

State the meaning of creeping error in 1 phase energy meter.

Description : State the meaning of creeping error in 1 phase energy meter.

Last Answer : Creeping error: It is defined as the slow and continuous rotation of the disc of the energy-meter when only pressure coil is energized with no current in the current coil (load current = 0). ... magnet on this iron wire is sufficient to prevent continues rotation of the disc on no load condition.

Define balanced and unbalanced load in three phase circuit.

Description : Define balanced and unbalanced load in three phase circuit.

Last Answer : Balanced Load: When all the imedances of 3 phases are equal in magnitude and of same nature then load is said to be balanced.  Unbalanced Load: When all the imedances of 3 phases are not equal in magnitude and of different nature then load is said to be unbalanced.

Describe the following errors and their compensation: (i) Phase error (ii) Speed error

Description : Describe the following errors and their compensation: (i) Phase error (ii) Speed error

Last Answer : (I) Phase error   1. In the phase error the phase difference angle between ∅ & ∅ is kept by using the shading band/ring  2. If the design and location of Shading band/ring is ... of brake magnet. By changing the position of the brake magnet speed of the rotating disc can be controlled. 

Describe with neat diagram phase sequence indicator.

Description : Describe with neat diagram phase sequence indicator.

Last Answer : Phase Sequence Indicator: There are two types of phase sequence indicators: (a) Rotating type phase sequence indicator (b) Static type phase sequence indicator (a) Rotating Type Phase Sequence ... of the supply is reversed or altered, then the lamp 1 will glow brighter than the lamp 2.

Draw and explain RC phase shift Oscillator.

Description : Draw and explain RC phase shift Oscillator.

Last Answer : Circuit diagram of RC phase shift oscillator: WORKING: * Circuit consists of a single stage amplifier in common emitter configuration & RC phase shifting network. * R1, R2, RE provides biasing & CE ... . * The phase shift around the loop is 3600 only at one precise frequency.  

In an R-C phase shift oscillator, the minimum no. of R-C networks to be connected in cascade will be -

Description : In an R-C phase shift oscillator, the minimum no. of R-C networks to be connected in cascade will be -

Last Answer : In an R-C phase shift oscillator, the minimum no. of R-C networks to be connected in cascade will be 3

What is the slip (as a percentage) when a 6 pole single phase induction motor operating on 220 V and 60 Hz is

Description : What is the slip (as a percentage) when a 6 pole single phase induction motor operating on 220 V and 60 Hz is rotating at speed of 1140 rpm? A) 60% B) 5% C) 10% D) None of these

Last Answer : What is the slip (as a percentage) when a 6 pole single phase induction motor operating on 220 V and 60 Hz is rotating at speed of 1140 rpm? A) 60% B) 5% C) 10% D) None of these

What is the power factor when a single phase watt meter operating on 200 V and 5 A for 5 hours makes 2016

Description : What is the power factor when a single phase watt meter operating on 200 V and 5 A for 5 hours makes 2016 revolutions and the meter constant in revolution is 420? A) 0.04 B) 1.04 C) 0.96 D) None of these

Last Answer : What is the power factor when a single phase watt meter operating on 200 V and 5 A for 5 hours makes 2016 revolutions and the meter constant in revolution is 420? A) 0.04 B) 1.04 C) 0.96 D) None of these

A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum

Description : A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum permissible stress in the dielectric is not to exceed 20 kV/mm. For economical size, the overall core diameter of the cable is (A) 28.2 mm (B) 26.4 mm (C) 24.4 mm (D) 22.0 mm

Last Answer : A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum permissible stress in the dielectric is not to exceed 20 kV/mm. For economical size, the overall core diameter of the cable is 22.0 mm

When a V-V three phase transformer system is converted into a Δ-Δ system, increase in capacity of the system is

Description : When a V-V three phase transformer system is converted into a Δ-Δ system, increase in capacity of the system is (A) 86.6% (B) 50% (C) 57.7% (D) 73.2%

Last Answer : When a V-V three phase transformer system is converted into a Δ-Δ system, increase in capacity of the system is 73.2%

Phase modifier is normally installed

Description : Phase modifier is normally installed

Last Answer : Phase modifier is normally installed in case of long lines

In a three-phase supply floating neutral is undesirable because it way give rise to?

Description : In a three-phase supply floating neutral is undesirable because it way give rise to?

Last Answer : In a three-phase supply floating neutral is undesirable because it way give rise to unequal line voltages across the load.

The phase difference between voltage and current wave through...

Description : The phase difference between voltage and current wave through a circuit element is given as 30°. The essential condition is that?

Last Answer : The phase difference between voltage and current wave through a circuit element is given as 30°. The essential condition is that both waves must have same frequency.

The power consumed in a circuit element will be least when the phase difference between the current and voltage is?

Description : The power consumed in a circuit element will be least when the phase difference between the current and voltage is?

Last Answer : The power consumed in a circuit element will be least when the phase difference between the current and voltage is 90°.

write short notes on single phase system.

Description : write short notes on single phase system.

Last Answer : A "phase" in an electrical system is often referred to as the waveform (may be voltage or the current) of the power supply. The waveform in an AC system is typically ... domestic household or commercial supplies and street lighting. Industrial supplies requires three phase electrical supply .

how can we reverse the direction of rotation of three phase induction motor?

Description : how can we reverse the direction of rotation of three phase induction motor ?

Last Answer : The direction of rotation of three phase induction motor can be reversed by plugging i.e by changing any two out of three phases of the supply to the stator of the Induction motor terminal.