Two resistances Rl and Ri are connected in series across the voltage source where Rl>Ri. The largest drop will be across?

1 Answer

Answer :

Two resistances Rl and Ri are connected in series across the voltage source where Rl>Ri. The largest drop will be across Rl.

Related questions

Description : The internal resistances of an ideal current source, and an ideal voltage source are, respectively, (A) 0, ∞ (B) ∞, ∞ (C) ∞, 0 (D) 0,0

Last Answer : The internal resistances of an ideal current source, and an ideal voltage source are, respectively, ∞, 0

Description : A DC voltage source is connected across a series RLC circuit. Under steady-state conditions, the applied DC voltage drops entirely across the

Last Answer : A DC voltage source is connected across a series RLC circuit. Under steady-state conditions, the applied DC voltage drops entirely across the C only

Description : In a series circuit with unequal resistances?

Last Answer : In a series circuit with unequal resistances the highest resistance has the highest voltage drop.

Description : Consider a circuit with four resistors in series connected to a voltage source. What happens to the voltage across each resistor, if the value of each of the resistors is doubled? A) It will double B) It will remain the same C) It will be halved D) It will become zero

Last Answer : Consider a circuit with four resistors in series connected to a voltage source. What happens to the voltage across each resistor, if the value of each of the resistors is doubled? A) It will double B) It will remain the same C) It will be halved D) It will become zero

Description : Source transformation Replace the circuit with voltage source in series with a single resistor

Last Answer : Source transformation Replace the circuit with voltage source in series with a single resistor

Description :  An independent voltage source in series with an impedance ZS=R+jXS delivers a maximum average power to a load impedance ZL when A) ZL = R B) ZL = jXS C) ZL = R-jXS D) ZL = R+jXS 

Last Answer :  An independent voltage source in series with an impedance ZS=R+jXS delivers a maximum average power to a load impedance ZL when ZL = R-jXS

Description : Series parallel resistances problem solution

Last Answer : Series parallel resistances problem solution

Description : What is the RMS voltage in a series RL circuit, if the voltage across R and L is 256 V and 192 V respectively? A) 320 V B) 448 V C) 64 V D) None of these

Last Answer : What is the RMS voltage in a series RL circuit, if the voltage across R and L is 256 V and 192 V respectively? A) 320 V B) 448 V C) 64 V D) None of these

Description :  With three resistances connected in parallel, if each dissipates 20 W the total power supplied by the voltage source equals?

Last Answer : Power is the only thing which is additive in both connection whether it is parallel or series connection so total power consumed will addition of all individual power =20+20+20 = 60 watt

Description : A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is :

Last Answer : A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is : 200 V

Description : Nodal Analysis with Voltage Sources dependent voltage source and two supernode

Last Answer : Nodal Analysis with Voltage Sources dependent voltage source and two supernode

Description : Nodal analysis example with voltage source and supernode

Last Answer : Nodal analysis example with voltage source and supernode

Description : Find power delivered by voltage source

Last Answer : Find power delivered by voltage source

Description : A voltage source inverter will have better performance if its  (1) load inductance is small and source inductance is large.  (2) both load and source inductance are small.  (3) both load and source inductances are large.  (4) load inductance is large and source inductance is small. 

Last Answer : A voltage source inverter will have better performance if its load inductance is large and source inductance is small. 

Description : A current controlled voltage source is equivalent to :  (A) series voltage feed -back amplifier (B) shunt current feed -back amplifier (C) shunt voltage feed -back amplifier (D) series current feed -back amplifier

Last Answer : A current controlled voltage source is equivalent to : shunt voltage feed -back amplifier

Description : A voltage source inverter is normally employed when  (1) source inductance is large and load inductance is small (2) source inductance is small and load inductance is large (3) both source and load inductance are small (4) both source and load inductance are large

Last Answer : 3

Description : Which of the following theorems enables a number of voltage (or current) source to be combined directly into a single voltage (or current) source. (1) compensation theorem (2) reciprocity theorem (3) superposition theorem (4) Millman's theorem

Last Answer : Which of the following theorems enables a number of voltage (or current) source to be combined directly into a single voltage (or current) source. (1) compensation theorem (2) reciprocity theorem (3) superposition theorem (4) Millman's theorem

Description : A network that consists of at least a voltage source or current source is called A) Active network B) Ideal network C) Sourced network D) Outsourced network

Last Answer : A network that consists of at least a voltage source or current source is called Active network

Description : In voltage source converter based HVDC transmission system the active power is controlled by changing (A) phase angle of the converter ac input voltage (B) supply frequency of the converter ac input voltage (C) magnitude of the converter ac input voltage (D) DC voltage at the inverter terminals

Last Answer : In voltage source converter based HVDC transmission system the active power is controlled by changing phase angle of the converter ac input voltage

Description : An ideal voltage source has?

Last Answer : An ideal voltage source has zero internal resistance.

Description : For a voltage source?

Last Answer : For a voltage source terminal voltage cannot be higher than source e.m.f.

Description : An ideal voltage source should have?

Last Answer : An ideal voltage source should have zero source resistance.

Description : Justify. Power MOSFET is operated at high enough gate source voltage to minimize the conduction losses. 

Last Answer : MOSFET is metal oxide field effect transistor. MOSFET is a voltage controlled device. MOSFET is majority carrier device. MOSFET are of two one is n-channel MOSFET and p-channel MOSFET. Gate, ... . Hence, power MOSFET is operated at high enough gate-source voltage to minimize the conduction losses.

Description : what is ideal voltage source?

Last Answer : every voltage source have their own resistance that is called as internal resistance it is because of the resistance of electrodes and electrolytes in the battery interms of other supplyit have ... in universe it means ideal voltage source is this voltage source having internal resistance zero

Description : What is Voltage Source Inverter (VSI) ?

Last Answer : Voltage Source Inverter (VSI)  Inverter is device which converts Direct Current (DC) to Alternating Current (AC). There are two types of inverters one is Voltage source inverter ... VSI consist of two load terminals and three phase VSI consist of three load terminals.

Description : Accurate measurement of very low resistances is possible with (A) Megger (B) Wheatstone Bridge (C) Kelvin’s Double Bridge (D) Wagner’s Earthing Device

Last Answer : Accurate measurement of very low resistances is possible with Kelvin’s Double Bridge

Last Answer : Resistances can be measured with the help of ohmmeters and resistance bridges.

Description : are AC and DC resistances same?

Last Answer : Resistance is the ability of a circuit or element (which is called resistor) to oppose current. Examples of Resistors with the ability of high resistance are Wood, Air, Mica, Glass, Rubber, Tungsten ... constant. Therefore, only the original resistance of wire comes into play. they are not the same

Description : Two resistors are said to be connected in series when?

Last Answer : Two resistors are said to be connected in series when same current passes in turn through both.

Description : A 40 W bulb is connected in series with a room heater. If now 40 W bulb is replaced by 100 W bulb, the heater output will?

Last Answer : A 40 W bulb is connected in series with a room heater. If now 40 W bulb is replaced by 100 W bulb, the heater output will increase.

Description : Two 100W, 200V lamps are connected in series across a 200V supply. The total power consumed by each lamp will be in Watts

Last Answer : 4800

Description : Source free RL circuit 8

Last Answer : Source free RL circuit 8

Description : Source free RL circuit 7

Last Answer : Source free RL circuit 7

Description : Source free RL circuit 6

Last Answer : Source free RL circuit 6

Description : Source free RL circuit 1

Last Answer : Source free RL circuit 1

Description : Source free RL circuit 2

Last Answer : Source free RL circuit 2

Description : Source free RL circuit 3

Last Answer : Source free RL circuit 3

Last Answer : Source free RL circuit 4

Last Answer : Source free RL circuit 5

Description : In an ac series RLC circuit, the voltage across R and L is 20 V; voltage across L and C is 9 V and voltage across RLC is 15 V. What is the voltage across C?

Last Answer : In an ac series RLC circuit, the voltage across R and L is 20 V; voltage across L and C is 9 V and voltage across RLC is 15 V. What is the voltage across C? 7 V

Last Answer : When two D.C. series motors are connected in parallel, the resultant speed is normal speed.

Description : what is equivalent resistance when four 4 Ohm resistors are connected in i) series ii) parallel

Last Answer : equivalent resistance

Description : role of the series resistance connected in PMMC movement.

Last Answer : A PMMC Instrument can be used as voltmeter by just connecting a series resistance with the moving coil. This series resistance is called Voltmeter Multiplier. This combination of moving coil and ... current whose voltage is to be measured. Ideally the resistance of voltmeter should be infinite

Description : An inductor is connected in series with SCR to protect it from A) Excessive high voltage B) Excessive high dv/dt C) Excessive high di/dt D) Excessive large forward current 

Last Answer : An inductor is connected in series with SCR to protect it from Excessive high di/dt

Description : We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance R.A. voltmeter having a resistance of 1.2 kOhm is connected across 600 Ohm resistance and read 5v. The value of resistance R will be

Last Answer : We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance R.A. voltmeter having a resistance of 1.2 kOhm is connected across 600 Ohm resistance and read 5v. The value of resistance R will be 2.4 kOhm

Description : What is the total resistance if 5 resistors of 20 Ω each are connected in series? A) 100 Ω B) 4 Ω C) 20 Ω D) None of these

Last Answer : What is the total resistance if 5 resistors of 20 Ω each are connected in series? A) 100 Ω B) 4 Ω C) 20 Ω D) None of these

Last Answer : In a A.C. series motor armature coils are usually connected to commutator through resistance.

Last Answer : When a D.C. series motor is connected to A.C. supply, the power factor will be low because of high inductance of field and armature circuits.

Description : Cells are connected in series in order to?

Last Answer : Cells are connected in series in order to increase voltage available.

Description : When a voltage of one volt is applied, a circuit allows one micro ampere current to flow through it. The conductance of the circuit is?

Last Answer : If v = 1 volt and i = 1 micro amp, i= 10^(-6)   So R = V/I,  R= 1/10^(-6) , R= 10^6  And now Conductance G = 1/R  So G = 10^(-6) mho..... Answer