For maximum transfer of power, internal resistance of the source should be?

For maximum transfer of power, internal resistance of the source should be?

by

1 Answer

Answer :

For maximum transfer of power, internal resistance of the source should be equal to load resistance.

by

Related questions

Maximum Power Transfer Theorem 1

Description : Maximum Power Transfer Theorem 1

Last Answer : Maximum Power Transfer Theorem 1

State maximum power transfer theorem for DC circuit.

Description : State maximum power transfer theorem for DC circuit.

Last Answer : Maximum power transfer theorem for DC circuit: The maximum power transfer theorem states that the source or a network transfers maximum power to load only when the load resistance is equal ... removed (disconnected) ii) All internal independent sources are replaced by their internal resistances.

Define the following terms as referred to battery. a) E.M.F b) Internal resistance c) Ah efficiency d) WAh efficiency

Description : Define the following terms as referred to battery. a) E.M.F b) Internal resistance c) Ah efficiency d) WAh efficiency

Last Answer : a) E.M.F : The electromotive force of a battery is defined as the energy spent or the work done in taking a unit positive charge around the complete circuit of the battery i.e., in ... input required to restore the initial state of charge, under specified conditions, is called Watt-hr efficiency.

"Maximum power output is obtained from a network when the load resistance...

Description : "Maximum power output is obtained from a network when the load resistance is equal to the output resistance of the network as seen from the terminals of the load". The above statement is associated with?

Last Answer : "Maximum power output is obtained from a network when the load resistance is equal to the output resistance of the network as seen from the terminals of the load". The above statement is associated with Maximum power transfer theorem.

For high efficiency of transfer of power, internal resistance of the source should be?

Description : For high efficiency of transfer of power, internal resistance of the source should be?

Last Answer : For high efficiency of transfer of power, internal resistance of the source should be less than the load resistance.

The internal resistances of an ideal current source, and an ideal voltage source are, respectively,

Description : The internal resistances of an ideal current source, and an ideal voltage source are, respectively, (A) 0, ∞ (B) ∞, ∞ (C) ∞, 0 (D) 0,0

Last Answer : The internal resistances of an ideal current source, and an ideal voltage source are, respectively, ∞, 0

An independent voltage source in series with an impedance ZS=R+jXS delivers a maximum average power to

Description :  An independent voltage source in series with an impedance ZS=R+jXS delivers a maximum average power to a load impedance ZL when A) ZL = R B) ZL = jXS C) ZL = R-jXS D) ZL = R+jXS 

Last Answer :  An independent voltage source in series with an impedance ZS=R+jXS delivers a maximum average power to a load impedance ZL when ZL = R-jXS

_______ electric power is the most common method used by electrical grids to transfer power.

Description : _______ electric power is the most common method used by electrical grids to transfer power.  (A) One-phase (B) Two-phase (C) Three-phase (D) None of the above

Last Answer : Three-phase electric power is the most common method used by electrical grids to transfer power. 

The reactive power transfer over a line mainly depends on

Description : The reactive power transfer over a line mainly depends on

Last Answer : The reactive power transfer over a line mainly depends on lVsl- lVRl

A certain power MOSFET has a maximum junction temperature specification of 1500o C, a junction-to-case

Description : A certain power MOSFET has a maximum junction temperature specification of 1500o C, a junction-to-case thermal resistance of 1.00 C/W, and a junction-to ambient thermal resistance of 600 C/W. If the ambient temperature is 300o C ... the device will be A) 1.52 W B) 1.72 W C) 1.92W D) 2.00 W

Last Answer : A certain power MOSFET has a maximum junction temperature specification of 1500o C, a junction-to-case thermal resistance of 1.00 C/W, and a junction-to ambient thermal resistance of  ... 300o C, then the maximum allowable power dissipation in the device will be 2.00 W 

The maximum reluctance power of a salient-pole synchronous motor having direct-axis reactance, 1.0 pu and

Description : The maximum reluctance power of a salient-pole synchronous motor having direct-axis reactance, 1.0 pu and quadrature-axis reactance, 0.5 pu, and input voltage, 1.0 pu is (A) 0.25 pu (B) 0.5 pu (C) 1.0 pu (D) 1.5 pu

Last Answer : The maximum reluctance power of a salient-pole synchronous motor having direct-axis reactance, 1.0 pu and quadrature-axis reactance, 0.5 pu, and input voltage, 1.0 pu is 0.5 pu

The condition for maximum power in case of D.C. motor is?

Last Answer : (b) Clostridium butylicum Lipase Removal of oil stains

The mechanical power developed by a shunt motor will be maximum when the ratio of back e.m.f. to applied voltage is?

Last Answer : The mechanical power developed by a shunt motor will be maximum when the ratio of back e.m.f. to applied voltage is 0.5.

In a D.C. shunt motor, under the conditions of maximum power, the current in the armature will be?

Last Answer : In a D.C. shunt motor, under the conditions of maximum power, the current in the armature will be more than full-load current.

In a power plant if the maximum demand on the plant is equal to the plant capacity, then?

Last Answer : In a power plant if the maximum demand on the plant is equal to the plant capacity, then plant reserve capacity will be zero.

Maximum demand on a power plant is?

Last Answer : Maximum demand on a power plant is the greatest of all "short time interval averaged" demand during a period.

The maximum load that a power transformer can carry is limited by its?

Description : The maximum load that a power transformer can carry is limited by its?

Last Answer : The maximum load that a power transformer can carry is limited by its voltage ratio.

What is the maximum value of power factor?

Description : What is the maximum value of power factor?

Last Answer : 1 is the maximum value of power factor.

The synchronous motor will develop maximum power when the load angle is?

Description : The synchronous motor will develop maximum power when the load angle is?

Last Answer : The synchronous motor will develop maximum power when the load angle is 900.

When an alternating current passes through an ohmic resistance the electrical power converted into heat is?

Description : When an alternating current passes through an ohmic resistance the electrical power converted into heat is?

Last Answer : When an alternating current passes through an ohmic resistance the electrical power converted into heat is true power.

What is the relationship between power and resistance?

Description : What is the relationship between power and resistance?

Last Answer : P = I2R Where P = power I = Current R = Resistance

When resistance element of a heater fuses and then we reconnect it ...

Description : When resistance element of a heater fuses and then we reconnect it after removing a portion of it, the power of the heater will?

Last Answer : When resistance element of a heater fuses and then we reconnect it after removing a portion of it, the power of the heater will increase.

Write down the steps involved for internal thread cutting on lathe machine.

Description : Write down the steps involved for internal thread cutting on lathe machine.

Last Answer : Steps involved for internal thread cutting on lathe machine  1) Hole is first bored to the root diameter of the thread. 2) Tool is fixed on the tool post or on the boring bar adjusted the angle of ... the start. 10) Keep going until the calculated depth of cut has been reached on the top slide.

List the types of Internal wiring in residential installations –

Description : List the types of Internal wiring in residential installations –

Last Answer : 1) Cleat wiring 2) Batten wiring 3) Wooden casing capping wiring 4) PVC conduit wiring 5) PVC casing capping wiring 6) Concealed wiring

State the concept of internal voltage drop.

Description : State the concept of internal voltage drop.

Last Answer : Concept of internal voltage drop: Every practical source offers some opposition to the current due to its internal parts or components. e.g. a 12V battery has electrodes made up of conducting ... internal voltage drop, the terminal voltage of practical voltage source is always less than its emf. 

What is internal voltage drop and terminal voltage?

Description : What is internal voltage drop and terminal voltage?

Last Answer : It is not permissible to just connect the positive terminal to the negative terminal of a cell with a copper wire. It will overheat and get damaged. This happens because the electromotive force (emf) ... than the nominal voltage (emf) of the cell and this lower voltage is called terminal voltage.

Sketch internal design of 4x3 ROM.

Description : Sketch internal design of 4x3 ROM.

Last Answer : The internal design of 4x3 ROM

Large internal faults are protected by?

Last Answer : Large internal faults are protected by merz price percentage differential protection.

does the BJT have internal capacitance?

Last Answer : Yes BJT have internal capacitances.

EPROM internal structure

Description : EPROM internal structure

Last Answer : EPROM (Erasable Programmable ROM): EPROM stands for Erasable Programmable ROM.Data is stored in EPROM memory cell as an electrostatic charge on highly insulated conductor. The charge can remain for ... figure shows EPROM memory cell consisting of a single NMOS filed effect transistor. 

Thevenin resistance Rth is found?

Description : Thevenin resistance Rth is found?

Last Answer : Thevenin resistance Rth is found between same open terminals as for Etk.

Mention The Steps In The Interrupt Driven Mode Of Data Transfer.?

Description : Mention The Steps In The Interrupt Driven Mode Of Data Transfer.?

Last Answer : Answer :The steps followed in this type of transfer are as follows: The peripheral device would request for an interrupt. The request acknowledgement for the transfer is issued at the end of ... coordinates by the ISS. Again the Interrupt system is enabled and the above steps are repeated.

How to Write a Job Transfer Request ?

Description : How to Write a Job Transfer Request ?

Last Answer : How to Write a Job Transfer Request No matter which type of industry you are in, there may come a point in your career when you would not want to settle for the current position that you have at ... push that your boss needs to finally take notice of the work that you have been doing in the past.

Heat Transfer Software

Description : Heat Transfer Software

Last Answer : The process of heat transfer is used in many industries - the scientific industry, engineering industry and every industry you can possibly think of that uses thermal heat. Because of this, there is a need ... group, so you won't have to go through the hassle of copying information down for others.

Heat Transfer Machines

Description : Heat Transfer Machines

Last Answer : Heat transfer machines are just the thing you need in order to do heat transfers on your clothing or whatever surface you want to decorate. In order for you to stick designs and precious stones on porous and ... is best. This will also give you an idea of what kind of designs you can choose from.

Heat Transfer Experiments

Description : Heat Transfer Experiments

Last Answer : Heat transfer experiments are basically experiments that deal with temperature, its characteristics and qualities. Heat transfer experiments are done for many purposes, but mainly to do investigations on the ... three are learned, it helps to have a better understanding of heat transfers as well.

Fuel Transfer Pumps

Description : Fuel Transfer Pumps

Last Answer : A fuel transfer pump is used to move fuel from one container to another. These pumps are used to fuel cars, planes, agricultural equipment and other devices. They are typically used to transfer diesel and ... for quicker fueling. These models may cost more, but they will make your job a lot easier.

How to transfer an apartment to a non-residential fund?

Description : How to transfer an apartment to a non-residential fund?

Last Answer : Can a private entrepreneur use his apartment as an office? The answer to this question depends on the type of activity. To sew, write poetry, fill out accounting documents, engage in tutoring, write ... is unacceptable. If you are not satisfied with this decision, you can appeal it in court.

Calculate the rate of heat transfer by radiation from an unlagged steam pipe, 50 mm o.d. at 393K to air at 293K emissivity e = 0.9.

Description : Calculate the rate of heat transfer by radiation from an unlagged steam pipe, 50 mm o.d. at 393K to air at 293K emissivity e = 0.9.

Last Answer : Rate of heat transfer by radiation Assume length of pipe = 1 m

Give the unit of overall heat transfer coefficient in SI and MKS.

Description : Give the unit of overall heat transfer coefficient in SI and MKS.

Last Answer : Unit of overall heat transfer coefficient 1. In SI : W/m2K 2. In MKS : kcal/hr m2K

Define film heat transfer coefficient.

Description : Define film heat transfer coefficient.

Last Answer : Film heat transfer coefficient: Film heat transfer coefficient h is defined as the quantity of heat transferred in unit time through unit area at a temperature difference of 10 between the surface and surrounding.

Define steady state heat transfer.

Description : Define steady state heat transfer.

Last Answer : Steady state heat transfer: Heat transfer where temperature remains same with respect to time and the rate of heat transfer does not vary with time.

Transfer switch

Description : Transfer switch

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

A transfer function has a second order denominator and constant gain in the numerator

Description : A transfer function has a second order denominator and constant gain in the numerator

Last Answer : A transfer function has a second order denominator and constant gain in the numerator the system has two zeros at infinity

The transfer of energy for reaction turbines is based on _______

Description : The transfer of energy for reaction turbines is based on _______ A) Newton’s first law B) Newton’s second law C) Newton’s third law D) All the above

Last Answer : The transfer of energy for reaction turbines is based on Newton’s third law

With the knowledge of the state variable representation of a plant the transfer function of the plant

Description : With the knowledge of the state variable representation of a plant the transfer function of the plant 

Last Answer : With the knowledge of the state variable representation of a plant the transfer function of the plant can be determined completely

Explain data transfer mechanism in I2C protocol.

Description : Explain data transfer mechanism in I2C protocol. Compare it with CAN and USB protocol based on bit rate and area of applications.

Last Answer : I2C (Inter-Integrated Circuit): I2C stands for Inter-Integrated Circuit. I2C is a serial protocol. It was developed by Philips Semiconductor. I2C bus have two communication lines. One is serial data ( ... Mbps this is used for lower speed devices. Using USB we can connect upto 127 devices.

Define : i) Maximum Value ii) RMS Value of ac supply

Description : Define : i) Maximum Value ii) RMS Value of ac supply

Last Answer : i) Maximum Value :- The maximum or peak value attained by an alternating quantity during positive or negative half cycle, is called maximum value or peak value.  ii) RMS Value of ac ... as produced by the alternating current when flowing through the same resistance and for the same time. 

Define the following terms: 1) Virtual height 2) Actual height 3) Critical frequency. 4) Maximum usable frequency.

Description : Define the following terms: 1) Virtual height 2) Actual height 3) Critical frequency. 4) Maximum usable frequency.

Last Answer : 1) Virtual height:- The incident and refracted rays follow paths that are exactly the same as they have been if reflection had taken place from a surface located at a greater height, called ... angle of incidence is other than the normal is known as maximum unstable frequency. MUF= fc secθ