Draw the output characteristics of BJT in CE configuration and label various regions on it.

1 Answer

Answer :

image

 output characteristics of BJT in CE configuration 

Related questions

Description : Draw: (i) Input characteristics of transistor in CE mode. (ii) Output characteristics of transistor in CE mode and show different regions on it.

Last Answer : (i) Input characteristics of transistor in CE mode.   (ii) Output characteristics of transistor in CE mode and show different regions on it.  

Description : Draw output characteristics of common emitter [CE] configuration and explain active, saturation and cut-off regions in detail. 

Last Answer : Characteristics of common emitter [CE] configuration Explanation :  (1) Active Region: In this region collector junction is reverse biased and emitter junction is forward biased. It is ... the transistor collector current is approximately given by VCC / RC and independent of base current. 

Description : State the applications of BJT.

Last Answer : Applications of BJT: 1. As a switch 2. As an amplifier 3. As a multivibrator 4. As a oscillator 5. As a timer circuit 6. As a Logic circuits 7. Delay circuits

Description : Sketch output characteristics of CE configuration. Show all the regions.

Last Answer : Sketch output characteristics of CE configuration. Show all the regions.

Description : Explain the operation of a full wave bridge rectifier with π filter using a neat diagram. Draw input and output waveforms.

Last Answer : During positive half-cycle of input, the secondary voltage VAB is positive, so diodes D1 and D2 forward biased and D3 and D4 reverse biased. The load current flows from terminal A ... smooth DC voltage appears across the load. The input and output waveforms are shown in the figure.

Description : Draw the input and output characteristics of CE configuration.

Last Answer : Input characteristics of CE configuration: Output characteristics of CE configuration:

Description : Define FHP motor and list various types.

Last Answer : Any motor rated less than one horse power may be called as fractional horse power motors(FHP) various types of FHP motors are: 1.Split phase induction motor 2. Capacitor start induction motor 3. Capacitor start capacitor run induction motor 4. Shaded pole induction motor. 

Description : Draw the block diagram of regulated power supply.

Last Answer : Block diagram of regulated power supply:

Description : Draw and explain: bridge rectifier with shunt capacitor filter.

Last Answer : Operation of bridge rectifier with capacitor filter is explained in different intervals with the help of the following wave form. Operation in interval at 0 to A: ... filter is very close to theideal dc voltage waveform as most of the ripple is removed from rectified output.

Description : Explain the operation of transistor as a switch and as an amplifier, with neat circuit diagrams. 

Last Answer : Explanation of transistor as a switch: The transistor can be used for two types of application viz. amplification and switching. For the amplification, transistor is biased in its active region. ... results in a large output voltage, which shows that the transistor works as an amplifier.

Description : List any 4 advantages and any 4 disadvantages of Integrated circuits.

Last Answer : Advantages of Integrated circuits:- 1. Extremely small size. 2. Very small weight . 3. Very low cost . 4. More reliable . 5. Lower power consumption . 6. Easy replacement ... achieved.  9.Large value of saturation resistance of transistors. 10.Voltage dependence of resistor and capacitors.

Description : Define filter and state it’s types.

Last Answer : A filter circuit may be defined as a circuit, which removes (or minimizes)the unwanted a.c. component of the rectifier output and allows only the d.c. component to reach the load. Types of filters 1) ... 2) Choke input filter(series inductor filter) 3) LC filter 4) π Filter 5) RC filter

Description : List different types of resistors and capacitors.

Last Answer : Types of Resistors: 1. Carbon Composition resistor 2. Thin film resistor 3. Thick film resistor 4. Wire wound resistor 5. Thermistor 6. LDR 7. Photo resistor Types of capacitors: 1 ... capacitor 2. Variable capacitor 3. Air ganged capacitor 4. PVC ganged capacitor 5. Trimmer capacitor

Description : Explain statically induced EMF and Dynamically induced EMF with neat diagrams.

Last Answer : Statically Induced EMF:- When changing magnetic field links with a stationary coil an emf is induced. This emf is called statically induced emf. Statically induced EMF is of two types: Self-induced ... cuts the field and an emf is induced. This emf is called dynamically induced emf.    

Description : Explain the working of auto-transformer and state any two advantages of it. 

Last Answer : Working of auto transformer :-It is a transformer with one winding only, part of this being common to both primary and secondary. In this transformer the primary and secondary are not electrically ... are less, so the efficiency of auto transformer is higher than that of two winding transformer.

Description : Define transformation ratio of a transformer.

Last Answer : Transformation Ratio (K) of a transformer: It is the ratio of secondary number of turns to primary number of turns. (OR) It is the ratio of secondary voltage to primary voltage. (OR ) It is the ratio of primary current to secondary current. OR

Description : Write the relation between RMS value and Average value.

Last Answer : The ratio of RMS value to average value is called the form factor of an alternating quantity.

Description : Define (i) Permeability (ii) Reluctance.

Last Answer : Permeability: The capability of the magnetic material to conduct the magnetic flux is known as permeability (OR) It is defined as ratio of magnetic flux density B in a medium to the magnetic flux intensity ... as the property of a material due to which it opposes the creation of magnetic flux in it.

Description : Define EMF and state its unit.

Last Answer : Electromotive force(EMF): A potential difference generated by a source of electrical energy across its terminals which tends to produce an electric current in a circuit is called electromotive force. Unit of EMF is Volt

Description : Explain ideal voltage source with suitable diagram.

Last Answer : A voltage source is a two terminal device which can maintain a fixed voltage. An ideal voltage source can maintain the fixed voltage independent of the load resistance or the output current. ... the terminal voltage remains constant equal to V volts without load (RL = ∞) or with load

Description : State the need for filters and list the different types of filters.

Last Answer : Need for filters 1) Output of all rectifiers is pulsating dc voltage and most of citcuits which work on dc requires pure dc voltage. 2) So in order to get pure dc waveform, filters are connected at the ... 2) Choke input filter(series inductor filter) 3) LC filter 4) π Filter 5) RC filter

Description : List the different transistor configurations.

Last Answer : The three different transistor configurations are, 1. Common emitter configuration(CE) 2. Common base configuration(CB) 3. Common collector configuration(CC)

Description : State why transistor is called as a bipolar device.

Last Answer : In case of transistor (BJT), the current conduction takes place due to both electrons and holes, ie, due to both positive as well as negative polarity charge carriers. Therefore transistor is called a bipolar device. 

Description : List any two applications of LED.

Last Answer : 1) LEDs are used in 7 segment display and dot matrix display. 2) They are used in opto couplers. 3) They are used for indicating power ON/OFF conditions. 4) They are used in infrared remote controls. 5) They are used as indicators in various electronic circuits.

Description : Define passive components and classify them.

Last Answer : Passive components: The components which by themselves are not capable of amplifying (or processing) electrical signals are known as passive components. They require external energy source for their functioning. These are bidirectional devices.  Classification: Resistors, Capacitors, Inductors etc.

Description : Compare analog and digital ICs.

Last Answer : Sr. No. Analog ICs Digital ICs  1 Analog ICs accept and output analog data through its pins. Digital ICs deal with only logic data inputs and outputs.  2 Almost every ... IC for dedicated application. Works with TTL logic level and works in voltage range of 0-5V only.

Description : Compare autotransformer with two winding transformer.

Last Answer : Two winding transformer Auto transformer 1.It has two separate windings : a) primary, b)secondary.  1. An auto transformer has single winding which acts both as primary and secondary ... varied. 3. They find application as boosters in AC feeders to increase the voltage levels.

Description : Define: (i) Efficiency (ii) Voltage regulation of transformer.

Last Answer : i) Efficiency : It is the ratio of output power to the input power of the transformer.It is denoted by η. ii) Voltage Regulation of transformer: The ratio of the change in Secondary Terminal ... So where, VNL = No Load Secondary voltage VFL = Full load secondary voltage

Description : State Faraday's first and second law of electromagnetic induction.

Last Answer : i)Faraday's First Law: Whenever a conductor cuts the magnetic lines of force or is cut by the magnetic lines of force or flux linking with conductor changes, an emf is induced in the conductor.  ... Law: The magnitude of induced emf is directly proportional to the rate of change of flux.

Description : Write emf equation of a transformer.

Last Answer : E.M.F equation of transformer is given by where Фm= Maximum value of ac flux linking with primary and secondary winding. f = frequency of applied ac signal N= number of turns on primary or ... in primary = E1=4.44 Фm f N1volts  Voltage induced in primary = E2=4.44 Фm f N2volts

Description : State the types of single phase induction motors.

Last Answer : The types of single phase induction motors are: i) Resistance split phase induction motor. ii) Capacitor split phase inductor motor. a. Capacitor start induction run motor b. permanent capacitor motor c. capacitor start capacitor run induction motor iii) Shaded pole induction motor.

Description : State the working principle of I ø transformer.

Last Answer : Working principle of transformer : Transformer works on the principle of mutual electromagnetic induction. When AC voltage is applied to the primary winding of a transformer it causes ac current to flow ... in the secondary winding. The current flows in the secondary circuit if load is connected.

Description : Define: (i) Inductive reactance (ii) Impedance.

Last Answer : i) Inductive reactance: Inductive reactance is the opposition offered by an inductor to alternating current . It is denoted by XL and given by XL = 2πf LΩ = ωL Ω ii)Impedance: It is the total opposition offered to flow of AC current in an AC circuit. It is denoted by Z and the unit is ohm. 

Description : With the help of waveforms and phasor diagrams, show the phase relationship between voltage and current in pure inductive circuit.

Last Answer : Phasor Diagram:  

Description : List the types of induced emf.

Last Answer : The types of induced emf are : i) Statically induced emf , ii) Dynamically induced emf

Description : Define: (i) Electromagnetism (ii) Magnetic flux.

Last Answer : i)Electromagnetism : It is the magnetism generated by electricity. OR  It is defined as the phenomenon associated with electric and magnetic fields and their interactions with each other. ii) Magnetic flux : The total number of magnetic lines of force in a magnetic field is called magnetic flux.

Description : Identify type of BJT configuration having following features : (i) BJT configuration having the least current gain. (ii) KIT configuration called as voltage follower. (iii) BJT ... configuration suitable for voltage amplification. (vi) BJT configuration having the least output impedance.  

Last Answer : (i) BJT configuration having the least current gain : Common Base Configuration  (ii) KIT configuration called as voltage follower: Common Collector Configuration  (iii) BJT ... Emitter Configuration  (vi) BJT configuration having the least output impedance: Common Collector Configuration

Description : Compare BJT common base configuration with common collector configuration on the basis of (i) Current gain (ii) Voltage gain (iii) Input impedance (iv) Output impedance

Last Answer : Parameter Common Base Common Collector Current gain Low (About 1) High (1+β) Voltage gain High 1  Input impedance  Low High Output impedance High Low

Description : Draw the construction of BJT (NPN) and explain its working principle. State and explain different operating regions.

Last Answer : Construction of BJT (NPN): Working of NPN Transistor : The circuit diagram of the NPN transistor is shown in the figure below. The forward biased is applied across the emitter-base ... Zero with input current is Zero transistor in cut off. In this region transistor act as open switch

Description : Comparison of three configuration of BJT

Last Answer : Parameter Common Base(CB) Common Emitter (CE) Common collector (CC) Input terminal  Emitter Base Base Common terminal Base Emitter Collector Output terminal Collector Collector Emitter Gain factor Alpha(Ic/Ie) Beta(Ic/Ib) Gamma(Ie/Ib)

Description : What is CB, CE and CC configuration ?

Last Answer : Buffer : A device or a circuit used to isolate two pt'ne circuits or stages. The emitter follows is a example of buffer. Alpha = IC / IE Beta = IC / IB

Description : (i) Discuss ideal and practical voltage source (ii) Compare CB, CC and CE configuration

Last Answer : (i) Discuss ideal and practical voltage source Ideal voltage source The ideal voltage source has a constant voltage across its terminal, irrespective of the current drawn from the source. Ideal Voltage Source have zero ... to reduce. (ii) Compare CB, CC and CE configuration

Description : Compare between CB , CE & CC transistor configuration.

Last Answer : Parameter CB CE CC I/P impedance Low Or 50Ω Medium Or 600Ωto 4kΩ High Or 1 MΩ Current Gain Less than or equal to 1 High Highest Voltage Gain Medium Medium Less ... k Ω to 50 k Ω Low Or 50 Ω Phase shift between input and output 0° 360° 0° 

Last Answer : Active , Saturation , Cut-off region of operations in BJT.

Description : Draw O/P characteristics of CB configuration and explain its working.

Last Answer : In common base configuration, emitter is the input terminal, collector is the output terminal and base terminal is connected as a common terminal for both input and output. The base-emitter ... In this region, a small collector current flows called leakage current when emitter current is zero.

Description : Draw the characteristics of tunnel diode, showing operating regions. State two applications of tunnel diode.

Last Answer : Applications: One of the important application of a tunnel diode is in high speed computers where the switching times in the order of nanoseconds or picoseconds are desirable. A tunnel diode can be ... In digital networks. 2. As a high speed switch. 3. As a high frequency oscillator.

Description : Draw circuit diagram of two stage RC coupled amplifier using BJT

Last Answer : BJT - To amplify input signal. R1 & R2 = Biasing resistor to provide DC biasing voltage RE = Emitter resistor to control gain RL = Load resistor to carry load current Cin = Cout = Coupling capacitors to block DC CE = emitter bypass resistor

Description : Draw symbol of NPN transistor and state three configurations of transistor (BJT)

Last Answer : Configuration - Common Emitter Common Collector Common Base

Description : Draw circuit diagram of voltage divider biasing list two advantages of voltage divider biasing of BJT.

Last Answer : Two advantages of voltage divider biasing of BJT. 1. It is very simple method of transistor biasing. 2. The biasing conditions can be very easily set. 3. there is no loading of ... 5. The resistor RE introduces a negative feedback. So all the advantages of negative feedback are obtained. 

Description : A modern power semiconductor device IGBT is combines the characteristics of a) BJT and MOSFET b) FCT and GTO c) SCR and MOSFET d) SCR and BJT

Last Answer : Ans: BJT and MOSFET