The current in a circuit with resistance in 6 amp. When an additional ...

The current in a circuit with resistance in 6 amp. When an additional resistance of 4 ohms is inserted the current drops to 4 amp. The original resistance in ohms is
by

1 Answer

Answer :

The current in a circuit with resistance in 6 amp. When an additional resistance of 4 ohms is inserted the current drops to 4 amp. The original resistance in ohms is 8.

by

Related questions

As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the total current in the circuit? EL-0036 A. 0.6 amp B. 0.833 amp C. 1.2 amps D. 2.4 amps

Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the total current in the circuit? EL-0036 A. 0.6 amp B. 0.833 amp C. 1.2 amps D. 2.4 amps

Last Answer : Answer: A

What is the total current in the illustrated circuit with a 6 volt battery if the resistance of R1 is 2 ohms, R2 is 4 ohms, and R3 is 4 ohms? EL-0021 A. 0.6 amp B. 1 amp C. 4 amps D. 6 amps

Description : What is the total current in the illustrated circuit with a 6 volt battery if the resistance of R1 is 2 ohms, R2 is 4 ohms, and R3 is 4 ohms? EL-0021 A. 0.6 amp B. 1 amp C. 4 amps D. 6 amps

Last Answer : Answer: D

In the illustrated circuit, if the battery is 24 VDC, the resistance of R1 is 24 ohms, and the resistance of R2 is 24 ohms, the total current is _________. EL-0019 A. 2 amps B. 1 amp C. 1/2 amp D. 2.4 amps

Description : In the illustrated circuit, if the battery is 24 VDC, the resistance of R1 is 24 ohms, and the resistance of R2 is 24 ohms, the total current is _________. EL-0019 A. 2 amps B. 1 amp C. 1/2 amp D. 2.4 amps

Last Answer : Answer: A

What would be the total current flowing in the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 1 amp B. 2 amps C. 5 amps D. 15 amps

Description : What would be the total current flowing in the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 1 amp B. 2 amps C. 5 amps D. 15 amps

Last Answer : Answer: B

When shipboard electrical distribution circuits are connected in parallel, additional parallel circuits will cause the total circuit resistance to _____________. A. increase, causing a drop in the line current B. increase, causing a decrease in the line voltage C. decrease, causing an increase in the line voltage D. decrease, causing an increase in the line current

Description : When shipboard electrical distribution circuits are connected in parallel, additional parallel circuits will cause the total circuit resistance to _____________. A. increase, causing a drop in the line current B ... an increase in the line voltage D. decrease, causing an increase in the line current

Last Answer : Answer: D

A 4 ῼ resistor carrying 2 Amp current will dissipate power equal to

Last Answer : A 4 ῼ resistor carrying 2 Amp current will dissipate power equal to 16 watts.

As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 24 kohms, and R2 is 3610 ohms what is the current flowing through R1? EL-0036 A. .434 milliamps B. .005 amp C. 6.00 amps D. 2.4 milliamps

Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 24 kohms, and R2 is 3610 ohms what is the current flowing through R1? EL-0036 A. .434 milliamps B. .005 amp C. 6.00 amps D. 2.4 milliamps

Last Answer : Answer: A

As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the current flowing through R1? EL-0036 A. 0.6 amp B. 0.833 amp C. 1.2 amps D. 2.4 amps

Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the current flowing through R1? EL-0036 A. 0.6 amp B. 0.833 amp C. 1.2 amps D. 2.4 amps

Last Answer : Answer: A

As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the current flowing through R2? EL-0036 A. 0.6 amp B. 0.833 amp C. 1.2 amps D. 2.4 amps

Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the current flowing through R2? EL-0036 A. 0.6 amp B. 0.833 amp C. 1.2 amps D. 2.4 amps

Last Answer : Answer: A

What is the current through R2 of the circuit illustrated if the resistances of R1 is 2 ohms, R2 is 4 ohms, and R3 is 4 ohms with a 6 volt battery? EL-0021 A. 0.5 amp B. 1.5 amps C. 3.0 amps D. 6 amps

Description : What is the current through R2 of the circuit illustrated if the resistances of R1 is 2 ohms, R2 is 4 ohms, and R3 is 4 ohms with a 6 volt battery? EL-0021 A. 0.5 amp B. 1.5 amps C. 3.0 amps D. 6 amps

Last Answer : Answer: B

In the illustrated circuit the voltage is 12 VDC and the resistance is 3 ohms. If the battery is rated for 120 amp-hours, how long before the voltage will drop to 1.75 volts per cell? EL-0018 A. 12 hours B. 1.75 days C. 30 hours D. 2.5 days

Description : In the illustrated circuit the voltage is 12 VDC and the resistance is 3 ohms. If the battery is rated for 120 amp-hours, how long before the voltage will drop to 1.75 volts per cell? EL-0018 A. 12 hours B. 1.75 days C. 30 hours D. 2.5 days

Last Answer : Answer: C

When an additional resistor is connected across an existing parallel circuit, the total resistance:

Description : When an additional resistor is connected across an existing parallel circuit, the total resistance: A. remains the same B. decreases by the value of the added resistor C. increases by the value of the added resistor D. decreases

Last Answer : When an additional resistor is connected across an existing parallel circuit, the total resistance: decreases

The illustrated circuits are used to measure ___________. EL-0024 A. resistance B. gauss or magnetic field strength C. battery discharge rate in Amp-hours D. current

Description : The illustrated circuits are used to measure ___________. EL-0024 A. resistance B. gauss or magnetic field strength C. battery discharge rate in Amp-hours D. current

Last Answer : Answer: A

If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω

Description : If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω

Last Answer : 500Ω

A 1:5 step-up transformer has 120V across the primary and 600 ohms resistance across the secondary. Assuming 100% efficiency, the primary current equals (A) 0.2 Amp. (B) 5 Amps. (C) 10 Amps. (D) 20 Amps.

Description : A 1:5 step-up transformer has 120V across the primary and 600 ohms resistance across the secondary. Assuming 100% efficiency, the primary current equals (A) 0.2 Amp. (B) 5 Amps. (C) 10 Amps. (D) 20 Amps.

Last Answer : I1= V1 /R1 = 120/600 = 0.2 (η = 100%, losses are zero ∴V1 = VR = I1R1)

Calculate the resistance of shunt required to make a milliammeter which gives maximum deflection for a current of 15 mA and which has a resistance of 5 Ω; read up to 10 Amp.

Description : Calculate the resistance of shunt required to make a milliammeter which gives maximum deflection for a current of 15 mA and which has a resistance of 5 Ω; read up to 10 Amp.

Last Answer : Answer :

What is the line current of a circuit when the current transformer of 1000 : 5 rating measures 4 amp?

Description : What is the line current of a circuit when the current transformer of 1000 : 5 rating measures 4 amp? (A) 5000 amp (B) 1000 amp (C) 400 amp (D) 800 amp 

Last Answer : What is the line current of a circuit when the current transformer of 1000 : 5 rating measures 4 amp? (A) 5000 amp (B) 1000 amp (C) 400 amp (D) 800 amp 

Describe the concept of virtual ground with reference to op-Amp.

Description : Describe the concept of virtual ground with reference to op-Amp.

Last Answer : Virtual ground concept:-In circuit point A is virtual ground. Figure shows inverting amplifier using op-amp. In this circuit non-inverting terminal is connected to the actual ground. Due to ... zero potential without actually grounding is known as virtual ground concept. Circuit diagram: 

Block Diagram of op-Amp

Description : Block Diagram of op-Amp

Last Answer : Block Diagram: The OP-AMP is basically a different amplifier i.e. it will amplify the voltage which is differentially present between its input terminals.  1.Input stage: The ... normally a complementary output stage. It increases the OPAMP. It also provides a low output resistance. 

In a 741 Op-Amp, there is 20 dB/decade fall-off starting at a relatively low frequency. This is due to the

Description : In a 741 Op-Amp, there is 20 dB/decade fall-off starting at a relatively low frequency. This is due to the (A) applied load (B) internal compensation (C) impedance of the source (D) power dissipation in the chip

Last Answer : In a 741 Op-Amp, there is 20 dB/decade fall-off starting at a relatively low frequency. This is due to the internal compensation

In an op-amp differentiator

Last Answer : In an op-amp differentiator the amplitude of output is proportional to rate of change of input.

A long wire carrying 100 amp is placed in an external magnetic field of...

Description : A long wire carrying 100 amp is placed in an external magnetic field of 50 gauss. The wire is at right angles to the field.

Last Answer : The field is null above the wire and crowded below

Without any additional circuitry, an 8:1 MUX can be used to obtain:...

Description : Without any additional circuitry, an 8:1 MUX can be used to obtain:  (1) Some but not all Boolean functions of 3 variables (2) All function of 3 variables but none of 4 variables (3) All functions of 3 variables and some but not all of 4 variables (4) All functions of 4 variables

Last Answer : A

Output resistance of an actual op-amp is A. 45Ω B. 46Ω C. 70Ω D. 75Ω

Description : Output resistance of an actual op-amp is A. 45Ω B. 46Ω C. 70Ω D. 75Ω

Last Answer : 75Ω

Why the input resistance of an ideal OPAMP is infinite and output resistance is zero? secondly, how can we measure these resistances(input and output) in case of an ideal OPAMPand Real OP-AMP in the following conditions when 1- load is not connected. 2- load is connected.

Description : Why the input resistance of an ideal OPAMP is infinite and output resistance is zero? secondly, how can we measure these resistances(input and output) in case of an ideal OPAMPand Real OP-AMP in the following conditions when 1- load is not connected. 2- load is connected.

Last Answer : Ans- Ideal OP-AMP is a power ful concept. If one goes through the history of amplifying devices it becomes clear that less it loads the previous stage better the output signal. ie ... . Can refer application notes by device manufacturer available in internet for more precise and practical solutions.

How many 1500 watt heaters can you run on a 20 amp circuit?

Description : How many 1500 watt heaters can you run on a 20 amp circuit?

Last Answer : As you did not specify the voltage of the circuit, I will I will assume your heaters are 110 volt portable heaters not 220 volt baseboard heaters.Each heater will draw 1500 watts / 110 volts = 13.64 ... more than half of the 20 ampere rating of the circuit, you can only run one of these heater.

Describe how Op-Amp is used as adder using circuit diagram and output voltage equation.

Description : Describe how Op-Amp is used as adder using circuit diagram and output voltage equation.

Last Answer : Summing Amplifier Circuit In this simple summing amplifier circuit, the output voltage, ( Vout ) now becomes proportional to the sum of the input voltages, V1, V2, V3, etc. Then we can ... to the non-inverting input of the op-amp, it will produce the positive sum of the input voltages.

Explain the function of sample and hold circuit by using op-amp.

Description : Explain the function of sample and hold circuit by using op-amp.

Last Answer : sample and hold circuit by using op-amp The n-channel MOSFET is driven by a control voltage VC acts as a switch. The control voltage VC is applied to the gate of the MOSFET ... called sample period. The time period during which the voltage across capacitor is constant is called Hold period.

A non inverting closed loop op amp circuit generally has a gain factor

Last Answer : A non inverting closed loop op amp circuit generally has a gain factor Greater than one.

In the common–emitter transistor circuit, if the current gain is 100 and the collector current is 10 mA, the

Description : In the common–emitter transistor circuit, if the current gain is 100 and the collector current is 10 mA, the base current is: (1) 10 µA (2) 100 µA (3) 1 A (4) 10 A 

Last Answer : In the common–emitter transistor circuit, if the current gain is 100 and the collector current is 10 mA, the base current is: 100 µA

The transient current in lossless L-C circuit when excited from an AC source is, sine wave

Description : The transient current in lossless L-C circuit when excited from an AC source is, sine wave  (a) Critically damped (b) Underdamped (c) Overdamped (d) Undamped

Last Answer : The transient current in lossless L-C circuit when excited from an AC source is, sine wave Undamped

A step voltage E is applied to a series R-L circuit. The rate of change of current is maximum at t = _:

Description : A step voltage E is applied to a series R-L circuit. The rate of change of current is maximum at t = _:  (1) Zero (2) Infinity (3) L/R (4) R/L 

Last Answer : A step voltage E is applied to a series R-L circuit. The rate of change of current is maximum at t = Zero.

When a voltage of 124 VDC is applied to the illustrated circuit with a resistance of 17.8 ohms the current will be ________. EL-0018 A. 0.143 amps B. 2.555 amps C. 6.966 amps D. 141.8 milliamps

Description : When a voltage of 124 VDC is applied to the illustrated circuit with a resistance of 17.8 ohms the current will be ________. EL-0018 A. 0.143 amps B. 2.555 amps C. 6.966 amps D. 141.8 milliamps

Last Answer : Answer: C

When a voltage of 112 VDC is applied to the circuit illustrated with a resistance of 17.8 ohms the current will be________. EL-0018 A. .158 amps B. 5.82 amps C. 6.29 amps D. 129.8m amps

Description : When a voltage of 112 VDC is applied to the circuit illustrated with a resistance of 17.8 ohms the current will be________. EL-0018 A. .158 amps B. 5.82 amps C. 6.29 amps D. 129.8m amps

Last Answer : Answer: C

When a voltage of 112 VDC is applied to the illustrated circuit with a resistance of 237 ohms the current will be ________. EL-0018 A. 1.47 amps B. 2.11 amps C. 347 milliamps D. 472.6 milliamps

Description : When a voltage of 112 VDC is applied to the illustrated circuit with a resistance of 237 ohms the current will be ________. EL-0018 A. 1.47 amps B. 2.11 amps C. 347 milliamps D. 472.6 milliamps

Last Answer : Answer: D

When a voltage of 110 VDC is applied to the illustrated circuit with a resistance of 17.8 ohms the current will be________. EL-0018 A. 2.88 amps B. 6.18 amps C. 127.8m amps D. 161 amps

Description : When a voltage of 110 VDC is applied to the illustrated circuit with a resistance of 17.8 ohms the current will be________. EL-0018 A. 2.88 amps B. 6.18 amps C. 127.8m amps D. 161 amps

Last Answer : Answer: B

When a voltage of 95 VDC is applied to the illustrated circuit with a resistance of 12 ohms the current will be _______. EL-0018 A. 6.126 amps B. 1.515 amps C. 7.916 amps D. 107 amps

Description : When a voltage of 95 VDC is applied to the illustrated circuit with a resistance of 12 ohms the current will be _______. EL-0018 A. 6.126 amps B. 1.515 amps C. 7.916 amps D. 107 amps

Last Answer : Answer: C

What is the total current of the illustrated circuit if the battery is 12 VDC and the resistance of R1 is 2 ohms, R2 is 3 ohms and R3 is 6 ohms? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps

Description : What is the total current of the illustrated circuit if the battery is 12 VDC and the resistance of R1 is 2 ohms, R2 is 3 ohms and R3 is 6 ohms? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps

Last Answer : Answer: D

When a voltage of 115 VDC is applied to the illustrated circuit with a resistance of 17.8 ohms the current will be _______. EL-0018 A. 0.154 amps B. 2.755 amps C. 6.46 amps D. 0.1328 amps

Description : When a voltage of 115 VDC is applied to the illustrated circuit with a resistance of 17.8 ohms the current will be _______. EL-0018 A. 0.154 amps B. 2.755 amps C. 6.46 amps D. 0.1328 amps

Last Answer : Answer: C

In the illustrated circuit, what is the voltage of the battery if the resistance of R1 is 150 ohms, the total resistance is 250 ohms and the current though R2 is 25 milliamps? EL-0036 A. 12 volts B. 24 volts C. 1.5 volts D. 6.25 volts

Description : In the illustrated circuit, what is the voltage of the battery if the resistance of R1 is 150 ohms, the total resistance is 250 ohms and the current though R2 is 25 milliamps? EL-0036 A. 12 volts B. 24 volts C. 1.5 volts D. 6.25 volts

Last Answer : Answer: D

What is the current flowing through R3 of the illustrated circuit if the battery is 12 VDC and resistance of R1 is 2 ohms, R2 is 3 ohms, and R3 is 6 ohms? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps

Description : What is the current flowing through R3 of the illustrated circuit if the battery is 12 VDC and resistance of R1 is 2 ohms, R2 is 3 ohms, and R3 is 6 ohms? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps

Last Answer : Answer: A

What is the current flowing through R2 of the illustrated circuit if the voltage is 12 VDC and the resistance of R1 is 2 ohms, R2 is 3 ohms and R3 is 6 ohms? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps

Description : What is the current flowing through R2 of the illustrated circuit if the voltage is 12 VDC and the resistance of R1 is 2 ohms, R2 is 3 ohms and R3 is 6 ohms? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps

Last Answer : Answer: B

What is the current flow through R1 of the circuit illustrated if the resistance of R1 is 2 ohms, R2 is 3 ohms and R3 is 6 ohms with a 12 VDC battery? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps

Description : What is the current flow through R1 of the circuit illustrated if the resistance of R1 is 2 ohms, R2 is 3 ohms and R3 is 6 ohms with a 12 VDC battery? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps

Last Answer : Answer: C

What is the current flowing through R1 of the illustrated circuit with a 6 VDC battery if the resistance of R1 is 2 ohms, R2 is 4 ohms and R3 is 4 ohms? EL-0021 A. 0.5 amps B. 1.5 amps C. 3.0 amps D. 6 amps

Description : What is the current flowing through R1 of the illustrated circuit with a 6 VDC battery if the resistance of R1 is 2 ohms, R2 is 4 ohms and R3 is 4 ohms? EL-0021 A. 0.5 amps B. 1.5 amps C. 3.0 amps D. 6 amps

Last Answer : Answer: C

The amount of current flowing through a circuit with a 40 V source and 6.8 kΩ of resistance is equal to:

Description : The amount of current flowing through a circuit with a 40 V source and 6.8 kΩ of resistance is equal to: A. 27.2 mA B. 59 mA C. 5.9 mA D. 590 mA

Last Answer : The amount of current flowing through a circuit with a 40 V source and 6.8 kΩ of resistance is equal to:  5.9 mA

A wire of length 100 cm is connected to a cell of emf 2 V and negligible internal resistance. The resistance of the wire is `3 Omega`. The additional

Description : A wire of length 100 cm is connected to a cell of emf 2 V and negligible internal resistance. The resistance of the wire is `3 Omega`. The additional

Last Answer : A wire of length 100 cm is connected to a cell of emf 2 V and negligible internal resistance. The ... B. `47Omega` C. `57Omega` D. `35Omega`

A kiosk a) is data organised and presented in a manner that has additional value beyond t he value of the data itself b) combines microscopic electronic components on a single integrated circuit that processes bits according to software instructions c) is a computer station that provides the public with specific and useful information and service d) describes a computer's type, processor, and operating system e) None of these

Description : A kiosk a) is data organised and presented in a manner that has additional value beyond t he value of the data itself b) combines microscopic electronic components on a single integrated circuit that ... and service d) describes a computer's type, processor, and operating system e) None of these

Last Answer : c) is a computer station that provides the public with specific and useful information and service

Low volt, High Amp current?

Description : Low volt, High Amp current?

Last Answer : Imagine a car battery. They are 12-15V and are capable of delivering 600 amps - when there is a conductor with very low resistance across the terminal. (Volts / current = resistance) so 12 volts/ 600 ... connect yourself to a car battery you will only get 12v/1,000,000 ohms = 12 microamps. Nothing.