1 Answer

Answer :

Hi Voltage Of measurement Equipment , ,,,,, 1 / electrostatic Volt Meters 2 / Royal Crotch Voltmeter 3 / Attracted Dix Type Electro Static Voltmeter.

Related questions

Description : Describe with neat circuit diagram the method of measurement of power in a High voltage, high current a.c circuit.

Last Answer : Circuit diagram:  Explanation:  The primary winding of P.T is connected across high voltage side and secondary winding is connected to pressure coil of low range wattmeter. The high voltage is ... is used Real power consumed = reading of wattmeter x ratio of C.T x ratio of P.T

Description : The device used ' for the measurement of current, voltage and resistance is: A. AVO meter B. Galvanometer C. Ammeter D. Ohm meter

Last Answer : ANSWER: A

Description : Instruments of Measure The device used ' for the measurement of current, voltage and resistance is: A. AVO meter B. Galvanometer C. Ammeter D. Ohm meter

Last Answer : ANSWER: A

Description : The device used ' for the measurement of current, voltage and resistance is: A. AVO meter B. Galvanometer C. Ammeter D. Ohm meter

Last Answer : ANSWER: A

Description : The device used ' for the measurement of current, voltage and resistance is: A. AVO meter B. Galvanometer C. Ammeter D. Ohm meter

Last Answer : ANSWER: A

Description : The most common unit of noise measurement in white noise voltage testing. A. NPR B. dBm C. dBW D. dBrn

Last Answer : A. NPR

Description : What is the necessity of shaft voltage measurement?

Last Answer : It is to observe insulation of bearing 6 & 7 and hydrogen seal assembly. It requires minimum leakage current (<100mA) through bearings and shaft seals to avoid pitting of bearings. ... >100mA, clean the insulation provided between bearing pedestal and seal housing with earth. 

Description : For dynamic strain measurement, the Wheatstone bridge used is of __________ type. (A) Voltage sensitive null (B) Voltage sensitive deflected (C) Current sensitive deflected (D) None of these

Last Answer : (B) Voltage sensitive deflected

Description : When taking a voltage measurement, which lead of the voltmeter should you connect to the circuit first?

Last Answer : Ground.

Description : On what range should you set the voltmeter prior to taking a voltage measurement?

Last Answer : Highest.

Description : Voltage measurement in a high impedance circuit requires a voltmeter with

Last Answer : high input impedance

Description : Explain the measurement of voltage and frequency using CRO.

Last Answer : Voltage Measurement: CRO displays the voltage signal as a function of time on its screen. The amplitude of that voltage signal is constant, but we can vary the number of divisions that cover the voltage ... /division nv is the number of divisions that cover the signal in vertical direction.

Description : Weins bridge is used for measurement of frequency in the applied voltage waveform is measurement of frequency in the applied voltage waveform is   (A)sinusoidal (B) square (C) rectangular (D) triangular

Last Answer : Weins bridge is used for measurement of frequency in the applied voltage waveform is measurement of frequency in the applied voltage waveform is sinusoidal 

Description : Define mean solar day. Explain the method for measurement of time.

Last Answer : Define mean solar day. Explain the method for measurement of time.

Description : Volumetric method of water measurement are

Last Answer : Ans.Furrows, Sprinklers and Drippers

Description : Which of the following is a method of indirect measurement of soil moisture?

Last Answer : Ans.Neutron moisture meter

Description : Which one of the following is not a method of measurement of National Income? (1) Value Added Method (2) Income Method (3) Investment Method (4) Expenditure Method

Last Answer : (3) Investment Method Explanation: Primarily there are three methods of measuring national income. The methods are product method, income method and expenditure method. Product method is given by Dr. Alfred ... properties where evidence of rates is slight, such as hotels, cinema, car park and etc.

Description : Capillary tube method of viscosity measurement is based on the (A) Hagen-Poiseuille’s equation (B) Stoke's law (C) Navier-stokes equation (D) None of these

Last Answer : (A) Hagen-Poiseuille’s equation

Description : Helium-mercury method is used for the measurement of the __________ of the catalyst. (A) Surface area (B) Porosity (C) Pore volume (D) Both (B) & (C)

Last Answer : (D) Both (B) & (C)

Description : The payback method for the measurement of return on investment (A) Gives a correct picture of profitability (B) Underemphasises liquidity (C) Does not measure the discounted rate of return (D) Takes into account the cash inflows after the recovery of investments

Last Answer : (C) Does not measure the discounted rate of return

Description : The rate of evaporation from reservoirs may be determined by (A) Pan-measurement method (B) Empirical formulae (C) Storage equation method (D) All the above

Last Answer : Answer: Option D

Description : Phytometer method is generally used for the measurement of (A) Interception (B) Evaporation (C) Transpiration (D) None of these

Last Answer : Answer: Option C

Description : According to ISI method of measurement, the order of the sequence is (A) Length, breadth, height (B) Breadth, length, height (C) Height, length, breadth (D) None of these

Last Answer : (A) Length, breadth, height

Description : What is a device that provides a method of sampling energy from within a waveguide for measurement or use in another circuit?

Last Answer : Directional Coupler

Description : Which of the following is not a method of measurement of price elasticity of demand in economics (a) Total Outlay ; (b) Total savings ; (c) Point method ; (d) Arc method

Last Answer : ; (b) Total savings

Description : The …………………………….. measurement method of national income aggregates all the money spent by private citizens, firms and the government within the year. (a) Expenditure ;(b) Income ; (c) Input ; (e) Saving

Last Answer : (a) Expenditure 

Description : How productivity is measured? Explain any one method of productivity measurement.

Last Answer : Measurement of productivity: - For measurement of productivity, one must find out input and output of the system. To measure the input resources and goods or services supplied is a critical job ... , cutting tools, coolant etc. Material productivity measures in terms of goods produced.

Description : Explain any one method of measurement of productivity.

Last Answer : Methods of measurement of productivity Various sources are utilized for production like labour, raw material, machine etc. accordingly productivity is called as labour productivity , raw material productivity, ... man hour. Labour productivity measures in terms of man hours utilised.   

Description : Explain with sketch torque measurement using (i) Stroboscope method, (ii) Capacitive method.

Last Answer : (i) Stroboscope method:-- Explanation : The arrangement of two flanges A and B placed at a distance on the shaft is as shown. Flange A carries a scale while flange a ... By applying a radiometric algorithm to the received signals, the signed relative angle between the rotors is calculated.

Description : State the procedure of measurement of horizontal angle by repetition method. 

Last Answer : The horizontal angle is measured very precisely using method of repetition as follows : 1) Set-up the theodolite over station O and level it properly. 2) Set the vernier A and vernier B at 0°0'0 ... repeat the same procedure. 9) The mean of both angles gives the horizontal angle AOB. 

Description : Explain differential pressure measurement method as indirect method for level measurement.

Last Answer : Differential pressure measurement as indirect method for level measurement:  Closed vessel: Differential pressure (DP) transmitters used for liquid level application measure hydrostatic pressure head. In a closed ... side of the DP and the low pressure side is vented to atmosphere.  

Description : Explain the capacitance type level measurement method with neat diagram.

Last Answer : Capacitance level indicator  Explanation: It consists of two conductors separated from each other by dielectric material between them. There is an insulated capacitance probe fixed near and parallel to ... , the dielectric constant changes due to which capacitance changes. Thus any change.

Description : Explain with principle the instrument for air purge method of level measurement.

Last Answer : Air purge method for of level measurement:  Principle: When liquid is held in a tank, then it exerts equal pressure on the walls of the tank. Such a pressure is due to the weight ... the hydrostatic pressure. The gauge then measures the air pressure needed to overcome the pressure of the liquid.

Description : List any two direct methods of level measurement. Explain Hydrostatic method of level measurement. Give one advantage and one disadvantage of it.

Last Answer : ➢ Direct methods of level measurement Direct methods 1. Hook type 2. Sight glass type 3. Float type 4. Dip stick ➢ Hydrostatic method of level measurement. ➢ A liquid in ... - 1. Their calibration gets changed according to variations in product density. 2. Require compressed air.

Description : Which one of the following is not a method of measurement of National Income ? (1) Value Added Method (2) Income Method (3) Investment Method (4) Expenditure Method

Last Answer : Investment Method 

Description : Explain the effect of power factor on wattmeter reading in two wattmeter method for power measurement.

Last Answer : Effect of P.F. on Reading of Wattmeter in Two Wattmeter Method:

Description : Describe the resistive method for liquid level measurement. Write its advantages and disadvantages.

Last Answer : Working: This method uses mercury as a conductor as shown in the figure. A number of contact rods are placed at various liquid levels. As the level of liquid rises in the tank, head h ... connected in series is calibrated in terms of the liquid level and indicates the liquid level directly. 

Description : List advantages and disadvantages of Radiation type level measurement method. 

Last Answer : Advantages : 1. Quite suitable for large reservoirs of 30-40 m diameter. 2. Continuous measurement is possible. 3. Non-contact device. 4. Measurement is independent on temperature, ... method due to radiation effects. 2. Adequate shielding is required to limit the radiation field intensity

Description : State two advantages and two disadvantages of photoelectric pick-up speed measurement method.

Last Answer : Advantages : 1) It is digital instrument so high accuracy. 2) Pulse amplitudes are constant. 3) This simplies the electronic circuitry. Disadvantages : 1) Light source must be replaced time to time. 2) The accuracy depends on the error represented by one pulse.

Description : Compare contact type and non-contact type speed measurement method.

Last Answer : Contact type method Non contact type method Physical contact between meter and shaft  No Physical contact between meterand shaft Consists of moving parts Does not consist of moving parts ... is less  Ex.AC / DC tachometer Ex. Rotary Encoder, Photo electric tachometer

Description : Name two methods for measurement of low, medium and high resistance. Give one advantage and one limitation of V- I method.

Last Answer : Methods for measurement of low resistance:  1. Ammeter voltmeter method  2. Kelvin's bridge method  3. Ohm meter method  4. Potentiometer method  5. Digital/analog multi-meter ... must be infinity for perfectly accurate measurement which is not possible.  2. Connection errors.

Description : State any two disadvantages of one wattmeter method of measurement of 3 phase power.

Last Answer : State any two disadvantages of one wattmeter method of measurement of 3 phase power. Disadvantages of one wattmeter method:- 1. Only used for balanced load 2. It can not be used for ... connection then neutral point must be available 4. Delta connection must be opened to connect current coil.

Description : Explain V- I method of measurement of medium resistance. 

Last Answer : In this method, use suitable source, ammeter and voltmeter and connect them as shown in the above diagram. Take reading of voltmeter and ammeter, then value of resistance = R = V/I Ω To minimise the error take 4 to 5 observation for the same resistance and take their average.

Description :  In the measurement of power of balanced load by two wattmeter method in a 3-phase circuit, The readings of the wattmeters are 4 kW and 2 kW respectively, the later is being taken after reversing the connections of current coil. the ... kVAR B) 0.2 & 6 √3 kVAR C) 0.32 & 2 kVAR D) 0.32 & 2 √3 kVAR

Last Answer :  In the measurement of power of balanced load by two wattmeter method in a 3-phase circuit, The readings of the wattmeters are 4 kW and 2 kW respectively, the later is being taken after reversing the ... of current coil. the power factor and reactive power of the load is 0.2 & 6 √3 kVAR

Description : For power measurement of three phase circuit by two wattmeter method, when the value of power factor is less than 0.5 lagging:

Last Answer : For power measurement of three phase circuit by two wattmeter method, when the value of power factor is less than 0.5 lagging: One of the wattmeter connections will have to be reversed

Description : Measurement of power and power factor of a 3-phase system by two wattmeter method can be obtained in case of  1. Balanced load and balanced source  2. Balanced source with 3-phase 3-wire unbalanced load  3. Unbalanced source with 3-phase 3 ... b) 2, 3 and 5 (c) 1, 2, 3, 4 and 5 (d) 1, 2, 3 and 5 

Last Answer : Measurement of power and power factor of a 3-phase system by two wattmeter method can be obtained in case of  1. Balanced load and balanced source  2. Balanced source with 3-phase 3-wire unbalanced load  3. Unbalanced source with 3- ... b) 2, 3 and 5 (c) 1, 2, 3, 4 and 5 (d) 1, 2, 3 and 5 

Description : In the measurement of power by two wattmeter method, when the readings of the two wattmeters are equal, the power factor is (A) Zero (B) Leading (C) Lagging (D) Unity

Last Answer : In the measurement of power by two wattmeter method, when the readings of the two wattmeters are equal, the power factor is Unity

Description : In two -wattmeter method of power measurement, if one wattmeter shows negative reading, then the power factor of the circuit is treated as (A) Unity (B) Lagging (C) Leading (D) Zero

Last Answer : Lagging   power   factor.

Description : Which method can be used for absolute measurement of resistance? A. Ohm's law method B. Wheatstone bridge method C. Both A & B D. None of these. 

Last Answer : Wheatstone bridge method can be used for absolute measurement of resistance.

Last Answer : In the case of power measurement by two wattmeter method in a balanced 3Φ system with a pure inductive load both the Wattmeter will indicate the same but of opposite sign.