In a power supply a shorted input capacitor is likely to result in

by

1 Answer

Answer :

In a power supply a shorted input capacitor is likely to result in No voltage output.

by

Related questions

If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the input signal C) Need for high dc collector supply D) Clipping of output in the negative half of the input signal

Description : If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the ... for high dc collector supply D) Clipping of output in the negative half of the input signal

Last Answer : B) Clipping of output in the positive half of the input signal

A capacitor is to be tested with a megohmmeter. If the meter is connected to a shorted capacitor, the meter pointer should _____________. A. immediately swing to the maximum resistance value B. deflect to zero and remain at that position C. swing to a high reading and gradually decrease D. swing to zero then gradually increase with slight pointer movements down scale

Description : A capacitor is to be tested with a megohmmeter. If the meter is connected to a shorted capacitor, the meter pointer should _____________. A. immediately swing to the maximum resistance value ... and gradually decrease D. swing to zero then gradually increase with slight pointer movements down scale

Last Answer : Answer: B

A capacitor can be tested using a megohmmeter or an ohmmeter. If the meter is connected to a shorted capacitor, the meter pointer should _____________. A. immediately swing to the maximum resistance value for the capacitor B. first swing quickly to 'zero', then gradually move up the scale as the capacitor charges C. immediately deflect to and remain at zero D. immediately swing to a high reading and then gradually decrease

Description : A capacitor can be tested using a megohmmeter or an ohmmeter. If the meter is connected to a shorted capacitor, the meter pointer should _____________. A. immediately swing to the maximum resistance ... deflect to and remain at zero D. immediately swing to a high reading and then gradually decrease

Last Answer : Answer: C

One diode of a full-wave rectifier has burned out in a shorted condition. Therefore, the output will be ____________. A. zero B. a rectified half-wave C. a rectified full-wave D. equal to the AC input

Description : One diode of a full-wave rectifier has burned out in a shorted condition. Therefore, the output will be ____________. A. zero B. a rectified half-wave C. a rectified full-wave D. equal to the AC input

Last Answer : Answer: D

What is the reactance property at the input of a shorted quarter wavelength line? A. A parallel LC circuit B. A pure inductive reactance C. A series LC circuit D. A pure capacitive reactance

Description : What is the reactance property at the input of a shorted quarter wavelength line? A. A parallel LC circuit B. A pure inductive reactance C. A series LC circuit D. A pure capacitive reactance

Last Answer : A. A parallel LC circuit

Characteristics impedance of a transmission line is the impedance measured at the ___________ when its length is infinite. A. input B. shorted end of the line C. output D. midsection

Description : Characteristics impedance of a transmission line is the impedance measured at the ___________ when its length is infinite. A. input B. shorted end of the line C. output D. midsection

Last Answer : A. input

A cylindrical rotor synchronous motor is switched on to the supply with its field windings shorted on

Description : A cylindrical rotor synchronous motor is switched on to the supply with its field windings shorted on themselves, the motor will .  A) Not start B) Start but will not run at synchronous speed C) Start as an induction motor and then run as a synchronous motor D) Start and run as a synchronous motor

Last Answer : A cylindrical rotor synchronous motor is switched on to the supply with its field windings shorted on themselves, the motor will Start but will not run at synchronous speed

What is aggregate supply exceeds aggregate demand what is likely to result?

Description : What is aggregate supply exceeds aggregate demand what is likely to result?

Last Answer : Need answer

How do you eliminate radio frequency variation of an oscillator transmitter caused by its supply voltage? A. Use new power supply B. Lossen power supply shielding C. Use of regulated power supply D. Use of high capacitor in the supply circuit

Description : How do you eliminate radio frequency variation of an oscillator transmitter caused by its supply voltage? A. Use new power supply B. Lossen power supply shielding C. Use of regulated power supply D. Use of high capacitor in the supply circuit

Last Answer : C. Use of regulated power supply

If the output filter capacitor in a power supply actually had a value twice its stated value, which of the

Description : If the output filter capacitor in a power supply actually had a value twice its stated value, which of the following symptoms would be found?   a. The output voltage would be doubled and a small ... would be greater than expected.  d. The output and ripple voltage would be less than expected.

Last Answer : b. The ripple voltage would be half of what is expected and a small increase in the output voltage would be detected. 

A three-phase, squirrel cage, induction motor will run hot due to a/an ______________. A. improper brush position B. reversed commutating pole C. shorted stator D. high power factor

Description : A three-phase, squirrel cage, induction motor will run hot due to a/an ______________. A. improper brush position B. reversed commutating pole C. shorted stator D. high power factor

Last Answer : Answer: C

The winch shown in the illustration will not operate in any speed in the lowering direction and at an abnormal speed in 'first point hoist'. The possible cause is that _______________. EL-0102 A. contactor coil '3M' has many shorted turns B. resistor 'R8-A2' has an open C. contacts '1M' in the power circuit are badly corroded D. master switch contacts 'MS6' have weak springs

Description : The winch shown in the illustration will not operate in any speed in the lowering direction and at an abnormal speed in 'first point hoist'. The possible cause is that _______________. EL-0102 A. ... '1M' in the power circuit are badly corroded D. master switch contacts 'MS6' have weak springs

Last Answer : Answer: B

A capacitor and coil in parallel is called

Description : A capacitor and coil in parallel is called

Last Answer : 1. A tuned circuit

A dielectric material is placed in between the plates of a capacitor, it

Last Answer : A dielectric material is placed in between the plates of a capacitor, it Increases the capacitance.

A capacitor stores energy in

Last Answer : A capacitor stores energy in Dielectric dipole

The capacitor charging current is

Last Answer : The capacitor charging current is An exponential growth function

The voltage across a capacitor _____ the current through it by ______

Last Answer : The voltage across a capacitor Lags the current through it by 90

For a pure capacitor, the voltage current relationship is:

Last Answer : For a pure capacitor, the voltage-current relationship is: Voltage lags current by 90*

Why shunt capacitor is used?

Description : Why shunt capacitor is used?

Last Answer : To improve voltage at receiving end and power factor

Why capacitor bank is used?

Description : Why capacitor bank is used?

Last Answer : In industrial or factory used E.B Power supply must be maintained above 0.90 power factor is compulsory for avoid EB Penalty. So APFC ( automatic Power factor control ) panel is used to maintained balance the load and PF maintained.

How do you charge a capacitor with a battery?

Description : How do you charge a capacitor with a battery?

Last Answer : The  capacitor  is  connected   in  parallel  with   the  battery.

What is the symbol of a capacitor?

Description : What is the symbol of a capacitor?

Last Answer : symbol of a capacitor

Which side of a capacitor is negative?

Description : Which side of a capacitor is negative?

Last Answer : In electrolytic type negative is shorter lead and usually mark in the tank. But of course not applicable to non-polar.

does capacitor store energy ?

Description : does capacitor store energy ?

Last Answer : yes capacitor stores energy

when capacitor act as open circuit?

Description : when capacitor act as open circuit?

Last Answer : When a DC is applied to capacitor it acts as open circuit .

which capacitor stores more charge ?

Description : which capacitor stores more charge ?

Last Answer : supercapacitor

what does a capacitor do?

Description : what does a capacitor do?

Last Answer : It store energy in.the form of charges It allows AC but restricted DC

In the illustration, the small battery and Rb are in the circuit to apply ________. EL-0022 A. forward bias to the emitter-base B. reverse bias to the emitter-base C. a 'reference charge' on the input capacitor D. a buffer between the input ground and the emitter ground

Description : In the illustration, the small battery and Rb are in the circuit to apply ________. EL-0022 A. forward bias to the emitter-base B. reverse bias to the emitter-base C. a 'reference charge' on the input capacitor D. a buffer between the input ground and the emitter ground

Last Answer : Answer: A

In an LC choke-input filter, what prevents the rapid charging of the capacitor?

Description : In an LC choke-input filter, what prevents the rapid charging of the capacitor?

Last Answer : The CEMF of the inductor

In an LC choke-input filter, what prevents the rapid charging of the capacitor?

Description : In an LC choke-input filter, what prevents the rapid charging of the capacitor?

Last Answer : Counter electro-motive force of the inductor.

A capacitor-start single phase induction motor is switched on to supply with its capacitor replaced by...

Description : A capacitor-start single phase induction motor is switched on to supply with its capacitor replaced by an inductor of equivalent reactance value. It will?

Last Answer : A capacitor-start single phase induction motor is switched on to supply with its capacitor replaced by an inductor of equivalent reactance value. It will not start at all.

In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 1 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal ... 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: A

In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

Basic operating characteristics of the operational amplifier such as gain and stability are the function of its _____________. A. differential input stage B. power output stage C. feedback circuit D. supply voltages

Description : Basic operating characteristics of the operational amplifier such as gain and stability are the function of its _____________. A. differential input stage B. power output stage C. feedback circuit D. supply voltages

Last Answer : Answer: C

A power supply produces a 0.6 W output with an input of 0.7 W. Its percentage of efficiency is:

Description : A power supply produces a 0.6 W output with an input of 0.7 W. Its percentage of efficiency is: A. 8.57% B. 42.85% C. 4.28% D. 85.7%

Last Answer : A power supply produces a 0.6 W output with an input of 0.7 W. Its percentage of efficiency is: 85.7%

A single-phase induction motor starts, comes up to about 75% rated speed, slows down to a lower speed, and accelerates again. The problem is most likely in the ____________. A. starting winding B. running winding C. starting capacitor D. running centrifugal switch

Description : A single-phase induction motor starts, comes up to about 75% rated speed, slows down to a lower speed, and accelerates again. The problem is most likely in the ____________. A. starting winding B. running winding C. starting capacitor D. running centrifugal switch

Last Answer : Answer: B

The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance C. reducing the input power to below its critical level. D. an impedance mismatch between the load and the line.

Description : The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance ... input power to below its critical level. D. an impedance mismatch between the load and the line.

Last Answer : D. an impedance mismatch between the load and the line.

Have you ever experienced a situation where a store or restaurant gave you the wrong change (shorted you) and what did you do about it?

Description : Have you ever experienced a situation where a store or restaurant gave you the wrong change (shorted you) and what did you do about it?

Last Answer : answer:If they “decided to stick” with the original, despite my insistence that I gave them $40, I’d demand the manager and have them count the drawer. I have absolutely no patience for shysters, and $10 is not “no big deal” to me.

Has anyone else had their dashboard lights shorted out by motor oil?

Description : Has anyone else had their dashboard lights shorted out by motor oil?

Last Answer : No, but…I had a new battery installed a couple years ago that flipped my gas gage needle backwards and while it has been spun around again, several times with a magnet, it still flips back into the dead zone every so often. haha Car stuff…PITA!

Why is the side-side shorted during the short circuit test in the transformer ?

Description : Why is the side-side shorted during the short circuit test in the transformer ?

Last Answer : During this test, any side of the transformer can be shorted, but for the following reasons, the side-side is shorted and 1. Lay-range instruments have the advantage of being connected to the high side ... both windings below 3% of the rated output , so it is convenient to measure on the high side.

How do you repair driver side airbag circuit low resistance or shorted Ford F150?

Description : How do you repair driver side airbag circuit low resistance or shorted Ford F150?

Last Answer : It might be a problem with the "clock spring".

When using the test set-up shown in the illustration, the lighted lamp indicates the winding is ____________. EL-0027 A. grounded B. good C. open D. shorted

Description : When using the test set-up shown in the illustration, the lighted lamp indicates the winding is ____________. EL-0027 A. grounded B. good C. open D. shorted

Last Answer : Answer: A

If a single-phase induction motor fails to start, the problem may be _____________. A. an open in the main winding B. a shorted shunt field C. a closed centrifugal switch D. low circuit frequency

Description : If a single-phase induction motor fails to start, the problem may be _____________. A. an open in the main winding B. a shorted shunt field C. a closed centrifugal switch D. low circuit frequency

Last Answer : Answer: A

If a DC motor runs faster than designed, with all other conditions being normal, the possible cause could be a/an ______________. A. shorted shunt field coil B. open armature coil C. reversed commutating pole D. overload

Description : If a DC motor runs faster than designed, with all other conditions being normal, the possible cause could be a/an ______________. A. shorted shunt field coil B. open armature coil C. reversed commutating pole D. overload

Last Answer : Answer: A

A shorted armature coil in a DC motor can be detected by _____________. A. sparking at the brushes B. shiny armature coil C. worn grooves in the armature D. undercut mica

Description : A shorted armature coil in a DC motor can be detected by _____________. A. sparking at the brushes B. shiny armature coil C. worn grooves in the armature D. undercut mica

Last Answer : Answer: A

If a single-phase induction motor fails to start, the problem may be _____________. A. an open in the run winding B. a shorted shunt field C. a closed centrifugal switch D. low circuit frequency

Description : If a single-phase induction motor fails to start, the problem may be _____________. A. an open in the run winding B. a shorted shunt field C. a closed centrifugal switch D. low circuit frequency

Last Answer : Answer: A