2 Answers

Answer :

In bjt the movement of electrons and hole totally depend on current.

Answer :

In  BJT  there  is  movement  of   electrons  and  holes   accros  the  junctions  which  is  basicaly  current  flow.

Related questions

Last Answer : No, BJT is a current controlled device .

Last Answer : BJT is current controlled device.

Last Answer : No, IGBT is not the current controlled device. IGBT is a voltage controlled device. IGBT have combine qualities of MOSFET and BJT. The high switching speed of MOSFET and low conduction losses of BJT. Also, IGBT which stands for Insulated Gate Bipolar Transistor have high input impedance.

Description :  If the base current of a BJT is 250 µA and emitter current is 15 mA, then the common base current gain will be A) 0.98 B) 0.41 C) 59 D) 55  

Last Answer :  If the base current of a BJT is 250 µA and emitter current is 15 mA, then the common base current gain will be 0.98 

Description : A current controlled voltage source is equivalent to :  (A) series voltage feed -back amplifier (B) shunt current feed -back amplifier (C) shunt voltage feed -back amplifier (D) series current feed -back amplifier

Last Answer : A current controlled voltage source is equivalent to : shunt voltage feed -back amplifier

Description : A 3 -phase, fully controlled, converter is feeding power into a DC load at a constant current of 150 A, the rms value of the current flowing through each thyristor of the converter is

Last Answer : Please show the solution for this question

Description : When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a load is 30°, the displacement power factor of the rectifier is

Last Answer : When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a load is 30°, the displacement power factor of the rectifier is √3/2

Last Answer : The gravity controlled instrument has crowded scale because current is proportional to sine of deflection angle.

Description : An FET is a better chopper than a BJT because it has (A) lower offset voltage (B) higher series ON resistance (C) lower input current (D) higher input impedance

Last Answer : An FET is a better chopper than a BJT because it has lower offset voltage

Description : What is a BJT?

Last Answer : Bipolar Junction Transistor (BJT): BJT is a Bipolar device. (Uses both electrons and holes charge carrier for current conduction) Two Junctions (Emitter junction & collector ... mode (Current amplification) Cutoff mode (Open switch) Saturation mode (Close switch)

Last Answer : Yes IGBT is costlier than BJT and MOSFET.

Last Answer : Yes BJT have internal capacitances.

Last Answer : BJT act as switch in saturation and  cutoff region ( ON state in saturation region and OFF state in cut-off region )

Last Answer : In cut-off region of BJT both the emitter-base junction and collector-base junction are reverse biased.

Last Answer : Active region of BJT act as amplifier.

Last Answer : Active , Saturation , Cut-off region of operations in BJT.

Last Answer : Yes BJT have second breakdown problem.

Last Answer : BJT have three terminals Base, emitter and collector.

Last Answer : When Q-point is at cut off region means it is just above the horizontal axis VCE

Last Answer : The proper flow of zero signal collector current and the maintenance of the proper collector emmiter voltage during passage of single called as transistor biasing

Last Answer : Beta is the current gain which is the ratio of collector current to base current.

Last Answer : BJT control the flow of electron so it is a active device.

Last Answer : Bipolar junction transistor

Last Answer : Transformer coupled amplifiers Direct coupled amplifiers Multistage amplifiers Darlington amplifiers Emmiter follower

Description : what are bjt transistors?

Last Answer : Bjt transistor is a type of transistor which  uses both electrons and hole charge carrier.bjts are used as switches and amplifiers.They amplify currents.

Last Answer : MOSFET  are voltage controlled devices.

Last Answer : Thyristor can only be turned on by small gate pulse but it cannot be turn off by using gate hence thyristor is called semi controlled device.

Last Answer : already answered here is mosfet current controlled device?

Description : State reason BJT is called as bipolar junction transistor.

Last Answer : BJT is called bipolar junction transistor because in BJT current conduction takes place due to majority as well as minority charge carriers.

Description : State 2 advantages of JFET over BJT.

Last Answer : Advantages of JFET over BJT: 1) High input impedance 2) Better thermal stability 3) Produce less noise 4) Smaller than BJT 5) Rugged in construction and simpler to fabricate 6) High degree of isolation between Input and Output. 

Description : List specification of BJT.

Last Answer : * The bipolar junction transistor (BJT) has small signal current gain, α (hfb). * Maximum collector current Ic (max). * Maximum collector to emitter voltage, VCE (max). * Collector to emitter ... . * Collector to emitter cut off voltage, VCEO. * Base emitter saturation voltage, VBE (sat).

Description : List configurations of BJT. 

Last Answer : Configurations of BJT : 1) Common Base (CB) configuration 2) Common Emitter (CE) configuration 3) Common Collector (CC) configuration

Description : State the need of biasing of BJT.

Last Answer : Need of biasing: The basic need of transistor biasing is to keep the base-emitter (B-E) junction properly forward biased and the collector-emitter (C-E) junction properly reverse biased ... transistor biasing is necessary for normal and proper operation of transistor to be used for amplification. 

Description : Draw circuit diagram of voltage divider biasing list two advantages of voltage divider biasing of BJT.

Last Answer : Two advantages of voltage divider biasing of BJT. 1. It is very simple method of transistor biasing. 2. The biasing conditions can be very easily set. 3. there is no loading of ... 5. The resistor RE introduces a negative feedback. So all the advantages of negative feedback are obtained. 

Description : Compare BJT with FET

Last Answer : FET BJT It is unipolar device i.e. current in the device is carried either by electrons or holes It is bipolar device i.e. current in the device is carried either by ... from minority- carrier storage effects & therefore has lower switching speeds & cut-off frequencies. 

Description : Compare between BJT and FET on the basis of (i) Biolar/Unipolar (ii) Tharmal Runaway (iii) Noise (iv) Applications

Last Answer : Parameter BJT FET Bipolar/Unipolar It is bipolar device i.e. current in this device is carried by electrons and holes. It is unipolar device i.e. current ... in oscilloscopes, electronic voltmeters and other measuring and testing equipment because of their high input impedance.

Description : Which phenomenon is present in thyristors but absent in BJT, MOSFET and IGBT ? (A) forward conduction (B) latching (C) forward blocking (D) reverse breakdown

Last Answer : Which phenomenon is present in thyristors but absent in BJT, MOSFET and IGBT ? (A) forward conduction (B) latching (C) forward blocking (D) reverse breakdown

Description : What is the difference between BJT and FET?

Last Answer : BJT  is  a  current  opperated   transistor  while  FET   is  a  field   opperated  transistor.

Description : What is a BJT amplifier?

Last Answer : Bilpolar Juntion transistor , this fuction is control the current

Description : How can BJT be used as an amplifier?