The output stage of a practical amplifier is always - - - coupled

by

1 Answer

Answer :

The output stage of a practical amplifier is always Transformer coupled

by

Related questions

Draw circuit diagram of two stage RC coupled amplifier using BJT

Description : Draw circuit diagram of two stage RC coupled amplifier using BJT

Last Answer : BJT - To amplify input signal. R1 & R2 = Biasing resistor to provide DC biasing voltage RE = Emitter resistor to control gain RL = Load resistor to carry load current Cin = Cout = Coupling capacitors to block DC CE = emitter bypass resistor

State the need of cascade amplifier and draw circuit diagram of 2-stage direct coupled amplifier.

Description : State the need of cascade amplifier and draw circuit diagram of 2-stage direct coupled amplifier.

Last Answer : Need:- The voltage (or power) gain, obtained from a single stage small signal amplifier, is limited. Therefore, it is not sufficient for all practical applications. Therefore, in order to obtain greater voltage and power gain, cascade amplifiers are used.

Draw the single stage RC coupled amplifier circuit and explain its’s operation.

Description : Draw the single stage RC coupled amplifier circuit and explain its’s operation.

Last Answer : Operation:- The capacitors C1 and C2 are called as the coupling capacitors. As the load resistor RL (not shown in the diagram) is coupled to the amplifier through the coupling capacitor ... connected in the common emitter (CE) configuration. Therefore, this amplifier is called CE amplifier. 

In the illustrated circuit, the amplifier is connected in what basic configuration? EL-0045 A. common emitter B. common collector C. darlington paired, capacitor coupled D. common base

Description : In the illustrated circuit, the amplifier is connected in what basic configuration? EL-0045 A. common emitter B. common collector C. darlington paired, capacitor coupled D. common base

Last Answer : Answer: D

Refers to one of the front end circuit of a VHF TV superheterodyne receiver which is usually a separate circuit coupled to the mixer. A. Antenna feed B. AGC C. RF amplifier D. Local oscillator

Description : Refers to one of the front end circuit of a VHF TV superheterodyne receiver which is usually a separate circuit coupled to the mixer. A. Antenna feed B. AGC C. RF amplifier D. Local oscillator

Last Answer : D. Local oscillator

In a resistance loaded, RC coupled amplifier the dc component is blocked by A) Load resistance RL B) Coupling capacitor, CC C) RB D) The transistor.

Description : In a resistance loaded, RC coupled amplifier the dc component is blocked by A) Load resistance RL B) Coupling capacitor, CC C) RB D) The transistor.

Last Answer : B) Coupling capacitor, CC

The Bandwidth of an RC-coupled amplifier is limited by: A) coupling capacitors at the low frequency end and bypass capacitors at the high frequency end B) coupling capacitors at the high frequency end and bypass capacitors at the low frequency end C) bypass and coupling capacitors at the low frequency end and shunt capacitors at the high frequency end and D) shunt capacitors at the low frequency end and bypass as well as coupling capacitors at the high frequency end.

Description : The Bandwidth of an RC-coupled amplifier is limited by: A) coupling capacitors at the low frequency end and bypass capacitors at the high frequency end B) coupling capacitors at the high frequency ... at the low frequency end and bypass as well as coupling capacitors at the high frequency end.

Last Answer : C) bypass and coupling capacitors at the low frequency end and shunt capacitors at the high frequency end and

What problem is caused in an rf amplifier by a loosely coupled transformer?

Description : What problem is caused in an rf amplifier by a loosely coupled transformer?

Last Answer : A too-narrow bandpass.

applications of RC coupled amplifier

Description :  applications of RC coupled amplifier

Last Answer : Applications of RC coupled amplifier: (i) Widely used as Voltage amplifiers. (ii) They are used in Public Address System. (iii) In Tape recorders. (iv) In stereo amplifiers (v) In T.V. V.C.R. and C.D. Players.

advantages and disadvantages of direct coupled amplifier over RC coupled amplifier.

Description : advantages and disadvantages of direct coupled amplifier over RC coupled amplifier. 

Last Answer : Advantages:  Due to absence of coupling capacitors, the gain does not reduce on the lower frequency side.  This amplifier can amplify dc signals. Reduced cost and complexity due to absence of ...   The output waveform has a dc shift.  Poor frequency response at a higher frequency.

transformer coupled amplifier

Description :  transformer coupled amplifier

Last Answer :  transformer coupled amplifier

State the need of multistage amplifier. Draw frequency response of R-C coupled amplifier.

Description : State the need of multistage amplifier. Draw frequency response of R-C coupled amplifier.

Last Answer : The need of multistage amplifier The voltage (or power) gain, obtained from a single stage small signal amplifier, is limited. Therefore, it is not sufficient for all practical applications. Therefore, in ... to use a MULTISTAGE AMPLIFIER .  Frequency response of R-C coupled amplifier.

Compare RC coupled, transformer coupled and direct coupled amplifier based on four points.

Description : Compare RC coupled, transformer coupled and direct coupled amplifier based on four points.

Last Answer : Parameter RC coupled Transformer coupled Direct coupled  Coupling element Resistor and capacitor Transformer No element Impedance matching Poor Excellent good Frequency ... Low frequency amplifier,opamp Size and cost small Large and bulky least

List the advantages of RC coupled amplifier.

Description : List the advantages of RC coupled amplifier.

Last Answer : Advantages: 1. The frequency response is excellent 2. The circuit is very compact and extremely light 3. Cost is low because it employ resistors and capacitors which are cheap 

Harmonic distortion of the signal is produced in an RC coupled transistor amplifier. The probable

Description : Harmonic distortion of the signal is produced in an RC coupled transistor amplifier. The probable component responsible for this distortion is  (A) The transistor itself  (B) the power supply Vcc  (C) the coupling capacitor Cc  (D) the biasing resistors

Last Answer : Harmonic distortion of the signal is produced in an RC coupled transistor amplifier. The probable component responsible for this distortion is The transistor itself 

The main component responsible for the fall of gain of an RC coupled amplifier in low frequency

Description : The main component responsible for the fall of gain of an RC coupled amplifier in low frequency range is  (A) The active device itself (tube, or transistor)  (B) stray shunt capacitance Cs  (C) the grid leak resistance Rg  (D) coupling capacitor Cc

Last Answer : The main component responsible for the fall of gain of an RC coupled amplifier in low frequency range is coupling capacitor Cc

What is the use of RC coupled amplifier?

Last Answer : the RC coupled amplifier are using the following applications first in public address amplifier system  tape recorders TV VCR and CD players stereo amplifier  and these are the voltage amplification amplifiers

The voltage at the reference electrode of the circuit shown in the illustration is applied to the input of a/an ______________. EL-0090 A. class A detector whose output drives an autotransformer B. operational amplifier whose output controls a step-up voltage reactor C. amplitude modulator whose output drives an 2-stage isolation transformer D. magnetic amplifier whose output controls a saturable reactor

Description : The voltage at the reference electrode of the circuit shown in the illustration is applied to the input of a/an ______________. EL-0090 A. class A detector whose output drives an ... drives an 2-stage isolation transformer D. magnetic amplifier whose output controls a saturable reactor

Last Answer : Answer: D

Basic operating characteristics of the operational amplifier such as gain and stability are the function of its _____________. A. differential input stage B. power output stage C. feedback circuit D. supply voltages

Description : Basic operating characteristics of the operational amplifier such as gain and stability are the function of its _____________. A. differential input stage B. power output stage C. feedback circuit D. supply voltages

Last Answer : Answer: C

The first stage of a two-stage amplifier has a voltage gain of 10, a 600 Ω input resistor, a 1600Ω equivalent noise resistance and 27kΩ output resistor. For the second stage, these values are 25, 81kΩ, 19kΩ, and 1MΩ, respectively. Calculate the equivalent input-noise resistance of this two stage amplifier. A. 2,518 kΩ B. 2,518 Ω C. 251.8 Ω D. 12,518 Ω

Description : The first stage of a two-stage amplifier has a voltage gain of 10, a 600 Ω input resistor, a 1600Ω equivalent noise resistance and 27kΩ output resistor. For the second stage, these values are 25, 81kΩ, 19kΩ, and 1MΩ, ... this two stage amplifier. A. 2,518 kΩ B. 2,518 Ω C. 251.8 Ω D. 12,518 Ω

Last Answer : B. 2,518 Ω

One of the following is a high powered RF ac basic transmitter that has two or more stages, the oscillator stage which determines the frequency opereation and RF amplifier stage orstages that develop the high power output. The purpose of which is to develop a good frequency stability. A. Goldsmith B. MOPA C. Alexanderson D. Hartley

Description : One of the following is a high powered RF ac basic transmitter that has two or more stages, the oscillator stage which determines the frequency opereation and RF amplifier stage orstages that develop the ... to develop a good frequency stability. A. Goldsmith B. MOPA C. Alexanderson D. Hartley

Last Answer : B. MOPA

Draw the single stage class A power amplifier circuit diagram and draw the input and output waveforms.

Description : Draw the single stage class A power amplifier circuit diagram and draw the input and output waveforms.

Last Answer : Circuit diagram:- Input / Output waveforms:-

Amplifiers are coupled to - - - -

Last Answer : Amplifiers are coupled to Increase gain

In the inverting configuration, what is the voltage (for all practical purposes) at the inverting input to the operational amplifier if the input signal is a 1-volt, peak-to-peak sine wave?

Description : In the inverting configuration, what is the voltage (for all practical purposes) at the inverting input to the operational amplifier if the input signal is a 1-volt, peak-to-peak sine wave?

Last Answer : 0 volts.

Explain DC coupled drive circuit with unipolar output.

Description : Explain DC coupled drive circuit with unipolar output.

Last Answer : DC coupled drive circuit with unipolar output: The figure shows the circuit and waveforms

A practical current source is usually represented by....

Description : A practical current source is usually represented by  a. A resistance in series with an ideal current source.  b. A resistance in parallel with an ideal current source.  c. A resistance in parallel with an ideal voltage source.  d. None of the above. 

Last Answer : A practical current source is usually represented by a resistance in parallel with an ideal current source.

Output transformer is always a - - - - transformer

Last Answer : Output transformer is always a Stepdown transformer

The most practical way to control the voltage output of an AC generator is to vary the _____________. A. number of windings B. speed of the rotating field C. strength of the rotating magnetic field D. power factor of the load

Description : The most practical way to control the voltage output of an AC generator is to vary the _____________. A. number of windings B. speed of the rotating field C. strength of the rotating magnetic field D. power factor of the load

Last Answer : Answer: C

How is output voltage controlled in practical alternators?

Description : How is output voltage controlled in practical alternators?

Last Answer : By varying the voltage applied to the field windings.

Draw the practical AM diode detector circuit. Sketch its input and output waveforms.

Description : Draw the practical AM diode detector circuit. Sketch its input and output waveforms. 

Last Answer : Practical AM diode detector 1. Skip distance:-Skip distance is defined as the shortest distance from a transmitter, measured along the surface of earth at which a sky wave of fixed frequency ... had taken place from a surface located at a greater height, called Virtual height of this layer.

A differential amplifier has a differential gain of 28000 and CMRR is 60 dB. What will be the value of common

Description : A differential amplifier has a differential gain of 28000 and CMRR is 60 dB. What will be the value of common mode gain? A) Ac = 0.125 B) Ac = 0.33 C) Ac = 3 D) Ac = 28 

Last Answer : A differential amplifier has a differential gain of 28000 and CMRR is 60 dB. What will be the value of common mode gain? A) Ac = 0.125 B) Ac = 0.33 C) Ac = 3 D) Ac = 28 

What is the efficiency of Class-B amplifier?

Description : What is the efficiency of Class-B amplifier?  A) 68.50% B) 78.50% C) 88.50% D) 98.50%

Last Answer : What is the efficiency of Class-B amplifier?  A) 68.50% B) 78.50% C) 88.50% D) 98.50%

Which one of the following is another name for common-collector amplifier?

Description : Which one of the following is another name for common-collector amplifier?  A) Source follower B) Collector follower C) Base follower D) Emitter follower

Last Answer : Which one of the following is another name for common-collector amplifier?  A) Source follower B) Collector follower C) Base follower D) Emitter follower

Positive feedback is used in 1. Amplifier 2. Rectifier 3.Oscillator 4. Detector

Description : Positive feedback is used in 1. Amplifier 2. Rectifier 3.Oscillator 4. Detector 

Last Answer : Positive feedback is used in 1. Amplifier 2. Rectifier 3.Oscillator 4. Detector 

A buffer amplifier is usually associated with

Description : A buffer amplifier is usually associated with (A) High input resistance (B) Low output resistance (C) Unity Voltage Gain (D) All Of the above

Last Answer : A buffer amplifier is usually associated with (A) High input resistance (B) Low output resistance (C) Unity Voltage Gain (D) All Of the above

The effect of a finite gain of an operational amplifier used in an integrator is that

Description : The effect of a finite gain of an operational amplifier used in an integrator is that (A) it would not integrate (B) the slope of the output will vary with time (C) the final value of the output voltage will reduce (D) there will be instability in the circuit

Last Answer : The effect of a finite gain of an operational amplifier used in an integrator is that there will be instability in the circuit

In a klystron amplifier the input cavity is called:

Description : In a klystron amplifier the input cavity is called:  (1) Buncher (2) Catcher (3) Pierce gun (4) Collector

Last Answer : In a klystron amplifier the input cavity is called: Buncher.

Negative feedback in amplifier: ...

Description : Negative feedback in amplifier:  (1) Improves the SNR at input (2) Improve SNR at output (3) Reduces distortion (4) Decreases bandwidth

Last Answer : Negative feedback in amplifier: Reduces distortion.

Which amplifier will be preferred for highest gain?

Description : Which amplifier will be preferred for highest gain?  (1) Darlington pair (2) Cascade amplifier (3) Cascode amplifier (4) Depends on the circuitry

Last Answer : Cascode amplifier will be preferred for highest gain.

For biomedical applications the mostly used amplifier is ...

Description : For biomedical applications the mostly used amplifier is  A) Single ended amplifier B) Differential amplifier  C) Inverting operational amplifier D) Chopper amplifier

Last Answer : Inverting opamp

No. of 20 watts loud speakers permitted to connect an 250 watt amplifier are

Last Answer : No. of 20 watts loudspeakers permitted to connect an 250 watt amplifier are 12.

In a CB amplifier the maximum efficiency could be

Last Answer : In a CB amplifier the maximum efficiency could be 25%.

In deriving ac equivalent circuit for an amplifier circuit we short circuit

Last Answer : In deriving ac equivalent circuit for an amplifier circuit we short circuit all capacitors.

For an amplifier, the coupling method which gives the highest gain is

Last Answer : For an amplifier, the coupling method which gives the highest gain is Transformer coupling.

in which region BJT act as amplifier?

Last Answer : Active region of BJT act as amplifier.

What is operational amplifier?

Description : What is operational amplifier?

Last Answer : Operational amplifier is an amplifier which amplifies the input signal when we pass a low voltage signal .It has two terminals inverting and non inverting. It is an active device because it ... of negative feedback it provides the output waveform similar to the input waveform (truely amplified )

In the illustrated circuit, one advantage of the capacitor coupling over direct coupling is ____________. EL-0048 A. as the frequency decreased the capacitive reactance (Xc) increases B. the amplifier becomes more efficient at lower capacitance. C. the arrangement allows the coupling of the signal while it isolates the biasing of each stage. D. good frequency response.

Description : In the illustrated circuit, one advantage of the capacitor coupling over direct coupling is ____________. EL-0048 A. as the frequency decreased the capacitive reactance (Xc) increases B. the amplifier becomes ... of the signal while it isolates the biasing of each stage. D. good frequency response.

Last Answer : Answer: C

The circuit shown in the illustration functions as a ____________. EL-0087 A. pulse trigger circuit for an operational amplifier B. three stage, high gain class 'A' amplifier C. binary ripple counter or shift register D. free running multivibrator

Description : The circuit shown in the illustration functions as a ____________. EL-0087 A. pulse trigger circuit for an operational amplifier B. three stage, high gain class 'A' amplifier C. binary ripple counter or shift register D. free running multivibrator

Last Answer : Answer: C

What part or section of a TV receiver that separates the sound and video signals? A. IF stage B. Video amplifier C. Video detector D. Burst separator

Description : What part or section of a TV receiver that separates the sound and video signals? A. IF stage B. Video amplifier C. Video detector D. Burst separator

Last Answer : C. Video detector

When measuring a transmitter’s frequency against a suitable standard, the frequency to be measured is taken from the A. oscillator stage B. intermediate amplifier C. buffer stage D. final RF stage

Description : When measuring a transmitter’s frequency against a suitable standard, the frequency to be measured is taken from the A. oscillator stage B. intermediate amplifier C. buffer stage D. final RF stage

Last Answer : D. final RF stage