Iron losses in a D.C. machine are independent of variations in (a) speed (b) load (c) voltage (d) speed and voltage

Iron losses in a D.C. machine are independent of variations in
(a) speed
(b) load
(c) voltage
(d) speed and voltage
by

1 Answer

Answer :

Ans: b
by

Related questions

In case of D.C. machines, mechanical losses are primary function of (a) current (b) voltage (c) speed (d) none of above

Description : In case of D.C. machines, mechanical losses are primary function of (a) current (b) voltage (c) speed (d) none of above

Last Answer : Ans: c

A separately excited generator as compared to a self-excited generator (a) is amenable to better voltage con-trol (b) is more stable (c) has exciting current independent of load current (d) has all above features

Description : A separately excited generator as compared to a self-excited generator (a) is amenable to better voltage con-trol (b) is more stable (c) has exciting current independent of load current (d) has all above features

Last Answer : Ans: d

Copper brushes in D.C. machine are used (a) where low voltage and high currents are involved (b) where high voltage and small cur-rents are involved (c) in both of the above cases (d) in none of the above cases

Description : Copper brushes in D.C. machine are used (a) where low voltage and high currents are involved (b) where high voltage and small cur-rents are involved (c) in both of the above cases (d) in none of the above cases

Last Answer : Ans: a

In a four-pole D.C. machine (a) all the four poles are north poles (b) alternate poles are north and south (c) all the four poles are south poles (d) two north poles follow two south poles

Description : In a four-pole D.C. machine (a) all the four poles are north poles (b) alternate poles are north and south (c) all the four poles are south poles (d) two north poles follow two south poles

Last Answer : Ans: b

The material for commutator brushes is generally (a) mica (b) copper (c) cast iron (d) carbon

Description : The material for commutator brushes is generally (a) mica (b) copper (c) cast iron (d) carbon

Last Answer : Ans: d

Iron losses in a D.C. machine are independent of variations in?

Last Answer : Iron losses in a D.C. machine are independent of variations in load.

The insulating material used between the commutator segments is normally (a) graphite (b) paper (c) mica (d) insulating varnish

Description : The insulating material used between the commutator segments is normally (a) graphite (b) paper (c) mica (d) insulating varnish

Last Answer : Ans: c

Brushes of D.C. machines are made of (a) carbon (b) soft copper (c) hard copper (d) all of above

Description : Brushes of D.C. machines are made of (a) carbon (b) soft copper (c) hard copper (d) all of above

Last Answer : Ans: a

In D.C. generators, current to the external circuit from armature is given through (a) commutator (b) solid connection (c) slip rings (d) none of above

Description : In D.C. generators, current to the external circuit from armature is given through (a) commutator (b) solid connection (c) slip rings (d) none of above

Last Answer : Ans: a

In lap winding, the number of brushes is always (a) double the number of poles (b) same as the number of poles (c) half the number of poles (d) two

Description : In lap winding, the number of brushes is always (a) double the number of poles (b) same as the number of poles (c) half the number of poles (d) two

Last Answer : Ans: b

In a commutator (a) copper is harder than mica (b) mica and copper are equally hard (c) mica is harder than copper (d) none of the above

Description : In a commutator (a) copper is harder than mica (b) mica and copper are equally hard (c) mica is harder than copper (d) none of the above

Last Answer : Ans: c

During short circuit test iron losses are negligible because A. The current on secondary side is negligible B. The voltage on secondary side does not vary C. The voltage applied on primary side is low D. Full-load current is not supplied to the transformer

Description : During short circuit test iron losses are negligible because A. The current on secondary side is negligible B. The voltage on secondary side does not vary C. The voltage applied on primary side is low D. Full-load current is not supplied to the transformer

Last Answer : C) the voltage applied on primary side is low

During short circuit test iron losses are negligible because A. The current on secondary side is negligible B. The voltage on secondary side does not vary C. The voltage applied on primary side is low D. Full-load current is not supplied to the transformer

Description : During short circuit test iron losses are negligible because A. The current on secondary side is negligible B. The voltage on secondary side does not vary C. The voltage applied on primary side is low D. Full-load current is not supplied to the transformer

Last Answer : C) the voltage applied on primary side is low

The voltage control in electric supply networks in required on account of which of the following reasons ? (a) Adjustment of voltage at consumers premises within statutory limits (b) Control of active and reactive power (c) Adjustment of short period daily and seasonal voltage variations in accordance with variations of load (d) All of the above

Description : The voltage control in electric supply networks in required on account of which of the following reasons ? (a) Adjustment of voltage at consumers premises within statutory limits (b) Control of ... daily and seasonal voltage variations in accordance with variations of load (d) All of the above

Last Answer : (d) All of the above

A three phase induction motor is driving full -load torque which is independent of speed. If the line voltage...

Description : A three phase induction motor is driving full -load torque which is independent of speed. If the line voltage drops to 90% of the rated value, % increase in motor copper losses  (a) 23% (b) -18% (c) 123% (d) None of these

Last Answer : A three phase induction motor is driving full -load torque which is independent of speed. If the line voltage drops to 90% of the rated value, % increase in motor copper losses (a) 23% (b) -18% (c) 123% (d) None of these

In a given transformer for a given applied voltage, losses which remain constant irrespective of load changes are?

Description : In a given transformer for a given applied voltage, losses which remain constant irrespective of load changes are?

Last Answer : In a given transformer for a given applied voltage, losses which remain constant irrespective of load changes are hysteresis and eddy current losses.

A 500 kVA, 3-phase transformer has iron losses of 300 W and full load copper losses of 600 W. The percentage

Description : A 500 kVA, 3-phase transformer has iron losses of 300 W and full load copper losses of 600 W. The percentage load at which the transformer is expected to have maximum efficiency is  (A) 50.0% (B) 70.7% (C) 141.4% (D) 200.0%

Last Answer : A 500 kVA, 3-phase transformer has iron losses of 300 W and full load copper losses of 600 W. The percentage load at which the transformer is expected to have maximum efficiency is 70.7%

A transformer has maximum efficiency at 3/4 full load. The ratio of its iron losses and full load copper loss is : -

Description :  A transformer has maximum efficiency at 3/4 full load. The ratio of its iron losses and full load copper loss is : -  a) 16/9 b) 4 / 3 c) 3/4 d) 9 /16

Last Answer :  A transformer has maximum efficiency at 3/4 full load. The ratio of its iron losses and full load copper loss is : -  9 /16

A dc shunt generator has a speed of 800 rpm when delivering 20 A to the load at the terminal voltage of 220V. If the same machine is run as a motor it takes a line current of 20A from 220V supply. The speed of the machine as a motor will be (A) 800 rpm. (B) more than 800 rpm. (C) less than 800 rpm. (D) both higher or lower than 800 rpm.

Description : A dc shunt generator has a speed of 800 rpm when delivering 20 A to the load at the terminal voltage of 220V. If the same machine is run as a motor it takes a line current of 20A from 220V supply. The speed of ... . (B) more than 800 rpm. (C) less than 800 rpm. (D) both higher or lower than 800 rpm.

Last Answer : (C) less than 800 rpm.

A 3-phase 50HZ SCIM takes a power input of 30 KW at its full load speed of 1440 rpm. Total stator losses are 1 KW. The slip and rotor ohmic losses at full load are a) 0.02, 600 W b) 0.04, 580 W c) 0.04, 1160 W d) 0.04, 1200 W

Description : A 3-phase 50HZ SCIM takes a power input of 30 KW at its full load speed of 1440 rpm. Total stator losses are 1 KW. The slip and rotor ohmic losses at full load are a) 0.02, 600 W b) 0.04, 580 W c) 0.04, 1160 W d) 0.04, 1200 W

Last Answer : Ans: 0.04, 1160 W

The basic control action of a magnetic amplifier depends upon _____________. A. variations in the load capacitance B. changes in inductance C. type of core material D. construction of the core

Description : The basic control action of a magnetic amplifier depends upon _____________. A. variations in the load capacitance B. changes in inductance C. type of core material D. construction of the core

Last Answer : Answer: B

A diagram which shows the variations of the axial load for all sections of the span of a beam, is called (A) Bending moment diagram (B) Shear force diagram (C) Thrust diagram (D) Stress diagram

Description : A diagram which shows the variations of the axial load for all sections of the span of a beam, is called (A) Bending moment diagram (B) Shear force diagram (C) Thrust diagram (D) Stress diagram

Last Answer : Answer: Option C

How much load variations can be generally allowed for variable spring?

Description : How much load variations can be generally allowed for variable spring?

Last Answer : 25%

Speaker is a device that __________. A. convert current variations into sound waves B. none of these C. convert electrical energy to mechanical energy D. convert sound waves into current and voltage

Description : Speaker is a device that __________. A. convert current variations into sound waves B. none of these C. convert electrical energy to mechanical energy D. convert sound waves into current and voltage

Last Answer : A. convert current variations into sound waves

The phases of the moon are partially the result of the------? A. Changes in the shape of the moon B. Revolution of the moon around the earth (Answer) C. Variations in the moon’s gravitation D. Variations in the speed of rotation of the moon

Description : The phases of the moon are partially the result of the------? A. Changes in the shape of the moon B. Revolution of the moon around the earth (Answer) C. Variations in the moon’s gravitation D. Variations in the speed of rotation of the moon

Last Answer : B. Revolution of the moon around the earth (Answer)

Which of the following is used to control the speed variations of the engine caused by the fluctuations of the engine turning moment? 1. D-slide valve 2. Governor 3. Flywheel 4. Meyer’s expansion valve

Description : Which of the following is used to control the speed variations of the engine caused by the fluctuations of the engine turning moment? 1. D-slide valve 2. Governor 3. Flywheel 4. Meyer’s expansion valve

Last Answer : 3. Flywheel

The stalling speed of an aeroplane is most affected by: a. Changes in air density b. Variations in aeroplane loading c. Variations in flight altitude d. Changes in pitch attitude

Description : The stalling speed of an aeroplane is most affected by: a. Changes in air density b. Variations in aeroplane loading c. Variations in flight altitude d. Changes in pitch attitude

Last Answer : b. Variations in aeroplane loading

You are attempting to parallel two AC generators and the synchroscope pointer stops at a position other than 0°. If you close the circuit breaker at this moment _____________. A. the incoming machine will accept all of the load B. the incoming machine will trip out on low voltage release C. a hazardous condition will be created by the cross current between the machines D. a hazardous condition will be created by the incoming machine being at a higher frequency than the bus

Description : You are attempting to parallel two AC generators and the synchroscope pointer stops at a position other than 0°. If you close the circuit breaker at this moment _____________. A. the incoming ... hazardous condition will be created by the incoming machine being at a higher frequency than the bus

Last Answer : Answer: C

Although saturable reactors are extremely useful in some applications, their gain is low because of ____________. A. core hysteresis losses B. inductive reactance in the control winding C. IR drop throughout the load winding D. all of the above

Description : Although saturable reactors are extremely useful in some applications, their gain is low because of ____________. A. core hysteresis losses B. inductive reactance in the control winding C. IR drop throughout the load winding D. all of the above

Last Answer : Answer: A

Petroff’s equation is used to find out (A) Load carrying capacity of the bearing (B) Frictional losses in the bearing (C) Unit bearing pressure on the bearing (D) Pressure distribution around the periphery of the journal

Description : Petroff’s equation is used to find out (A) Load carrying capacity of the bearing (B) Frictional losses in the bearing (C) Unit bearing pressure on the bearing (D) Pressure distribution around the periphery of the journal

Last Answer : (B) Frictional losses in the bearing

Which of the following methods does not take into account the maximum temperature rise under variable load conditions ? (a) Equivalent power method (b) Equivalent current method (c) Method of average losses (d) Equivalent torque method

Description : Which of the following methods does not take into account the maximum temperature rise under variable load conditions ? (a) Equivalent power method (b) Equivalent current method (c) Method of average losses (d) Equivalent torque method

Last Answer : (c) Method of average losses

By which of the following methods motor rating for variable load drives can be determined ? (a) Method of average losses (b) Equivalent current method (c) Equivalent torque method (d) Equivalent power method (e) All of the above.

Description : By which of the following methods motor rating for variable load drives can be determined ? (a) Method of average losses (b) Equivalent current method (c) Equivalent torque method (d) Equivalent power method (e) All of the above.

Last Answer : (e) All of the above.

Which losses in a transformer varies significantly with load

Description : Which losses in a transformer varies significantly with load  a. Hysteresis losses b. Eddy current losses c. Copper losses d. Core losses 

Last Answer : Which losses in a transformer varies significantly with load Copper losses

If the lagging power factor of the load decreases, the line losses will

Description : If the lagging power factor of the load decreases, the line losses will (A) Decrease (B) Increase (C) Flrst decrease and then Increase (D) Remain same

Last Answer : If the lagging power factor of the load decreases, the line losses will Increase

A 150 kW electric motor has an efficiency of 92 %, when it operates at full load. Calculate the losses in the...

Description : A 150 kW electric motor has an efficiency of 92 %, when it operates at full load. Calculate the losses in the machine.  (A) 92 kW (B) 150 kW (C) 163 kW (D) 13 kW 

Last Answer : efficiency  -output /input * 100 150/0.92----------163(input) losses-----(163--150)  ---------13kw.

In a synchronous motor which losses varies with load?

Description : In a synchronous motor which losses varies with load?

Last Answer : In a synchronous motor, copper losses varies with load.

In synchronous motor, does the winding losses vary with load?

Description : In synchronous motor, does the winding losses vary with load?

Last Answer : No, in the synchronous motor the winding losses do not vary with load.

Free (threshed) seed carried over the Walker or rack in straw and discharge from the rear of machine is called as :- a) Cylinder loss b) Walker losses (rack loss) C) Shoe loss d) Gathering losses

Description : Free (threshed) seed carried over the Walker or rack in straw and discharge from the rear of machine is called as :- a) Cylinder loss b) Walker losses (rack loss) C) Shoe loss d) Gathering losses

Last Answer : b) Walker losses (rack loss)

Unthreshed seed discharge from the rear of the machine either in straw or in the material from the cleaning shoe is called :- a) Cylinder loss b) Walker losses(rack loss) C) Shoe loss d) Gathering losses

Description : Unthreshed seed discharge from the rear of the machine either in straw or in the material from the cleaning shoe is called :- a) Cylinder loss b) Walker losses(rack loss) C) Shoe loss d) Gathering losses

Last Answer : a) Cylinder loss

The armature of a dc machine is laminated to reduce: (A) Eddy current loss (B) Hysteresis loss (C) copper losses (D) friction and windage losses

Description : The armature of a dc machine is laminated to reduce: (A) Eddy current loss (B) Hysteresis loss (C) copper losses (D) friction and windage losses

Last Answer : Ans: A Thinner the laminations, greater is the resistance offered to the induced e.m.f., smaller the current and hence lesser the I2R loss in the core.

Losses in dc machine..?

Last Answer : Copper losses,iron losses,variable losses , constant losees

What is the percentage of stray losses in DC machine?

Description : What is the percentage of stray losses in DC machine?

Last Answer : Percentage of stray losses in DC machine is about 1 % .

what are the losses in DC machine?

Last Answer : Iron loss, copper loss and mechanical losses these are the losses in DC machine.

Line losses in a distribution circuit are kept to a minimum by __________. A. adding rubber insulation conductors to the circuit B. using higher current and lower voltage C. increasing the number of thermal relays in the circuit D. using higher voltage and lower current

Description : Line losses in a distribution circuit are kept to a minimum by __________. A. adding rubber insulation conductors to the circuit B. using higher current and lower voltage C. increasing the number of thermal relays in the circuit D. using higher voltage and lower current

Last Answer : Answer: D

For a shortened vertical antenna, where should a loading coil be placed to minimize losses and produce the most effective performance? A. As low as possible on the vertical radiator B. Near the center of the vertical radiator C. As close to the transmitter as possible D. At a voltage node

Description : For a shortened vertical antenna, where should a loading coil be placed to minimize losses and produce the most effective performance? A. As low as possible on the vertical radiator B. Near the center of the vertical radiator C. As close to the transmitter as possible D. At a voltage node

Last Answer : B. Near the center of the vertical radiator

The power transmitted will be maximum when (a) corona losses are minimum (b) reactance is high (c) sending end voltage is more (d) receiving end voltage is more

Description : The power transmitted will be maximum when (a) corona losses are minimum (b) reactance is high (c) sending end voltage is more (d) receiving end voltage is more

Last Answer : (c) sending end voltage is more

Explain the following energy conservation techniques: (i) By reducing I2R losses in Trans. system (ii) By optimizing distribution voltage.

Description : Explain the following energy conservation techniques: (i) By reducing I2R losses in Trans. system (ii) By optimizing distribution voltage.

Last Answer : i) By reducing I2R losses in Trans:  1. Opting for low resistance All Aluminum Alloy conductors (AAAC) in place of conventional aluminum cored steel reinforced (ACSR) lines. 2. ... line power losses. Thus maintaining the voltages at the specified levels leads to energy savings/conservation.

Justify. Power MOSFET is operated at high enough gate source voltage to minimize the conduction losses.

Description : Justify. Power MOSFET is operated at high enough gate source voltage to minimize the conduction losses. 

Last Answer : MOSFET is metal oxide field effect transistor. MOSFET is a voltage controlled device. MOSFET is majority carrier device. MOSFET are of two one is n-channel MOSFET and p-channel MOSFET. Gate, ... . Hence, power MOSFET is operated at high enough gate-source voltage to minimize the conduction losses.

Why are iron losses considered as constant losses in transformer?

Description : Why are iron losses considered as constant losses in transformer?

Last Answer : Iron losses depend on supply frequency and flux density in the core. For all normal operations, the frequency of flux reversals which is same as supply frequency is constant and the value of flux density ... . Hence iron losses remain constant under all load conditions. i-e from no-load to full-load

[53] The iron loss of the transformer is negligible during short circuit test because A. The entire input is just sufficient to meet Cu losses only B. Flux produced is a small fraction of the normal flux C. Iron core becomes fully saturated D. Supply frequency is held constant

Description : [53] The iron loss of the transformer is negligible during short circuit test because A. The entire input is just sufficient to meet Cu losses only B. Flux produced is a small fraction of the normal flux C. Iron core becomes fully saturated D. Supply frequency is held constant

Last Answer : B. Flux produced is a small fraction of the normal flux