What is voltage voltage regulator IC ?

1 Answer

Answer :

: All the ICs that are used to regulate or control the voltage are called voltage regulator ICs. The function of the voltage regulator IC is to regulate the voltage. E.g. IC 7805.

Related questions

Description : Describe the functional pin diagram of regulator IC 78XX and 79XX.

Last Answer : IC 78XX: Explanation: 78XX series of IC regulators is representative of three terminal devices that are available with several fixed positive output voltages. It has three terminals labeled ... can also use 25μF aluminum electrolytic capacitor. Values given may be increased without limit. 

Description : Give some examples of monolithic IC voltage regulators

Last Answer : 78XX series fixed output, positive voltage regulators 79XX series fixed output, negative voltage regulators 723 general purpose regulator.

Description : What are the advantages of IC voltage regulators?

Last Answer : *low cost *high reliability *reduction in size *excellent performance

Description : Sketch pin configuration of IC 723. State functions of each pin. Sketch circuit diagram for obtaining 6V output d.c. regulated voltage using IC 723.

Last Answer : 1) Pin configuration of IC 723 :  2) Functions of each pin:-  V+ and V-: These are the supply voltage terminals of the IC. V+ is the positive terminal and V- is the negative terminal.  Non ... Expression Vout = Vref * (R2 / R1+R2)  Assume any value of R2, R1 can be calculated. 

Description : What is a voltage regulator in Arduino?

Last Answer : A voltage regulator in Arduino is an electronic component that regulates the voltage level of a circuit and ensures that it remains constant.

Description : Where is voltage regulator located on 1970 Chevelle?

Last Answer : It is attached to the inside of the radiator support.

Description : The illustrated device is a _______. EL-0064 A. full wave bridge rectifier B. half wave bridge rectifier C. solid state voltage regulator D. direct current (DC) filter

Last Answer : Answer: A

Description : When paralleling two AC generators, the frequency of the incoming machine immediately prior to closing its breaker should be ____________. A. controlled by placing the governor switch in the automatic ... regulator C. slightly greater than the bus frequency D. slightly less than the bus frequency

Last Answer : Answer: C

Description : The device labeled 'REG SW' in the illustration is used to ___________. EL-0003 A. shift from the automatic voltage regulator to the manual voltage regulator B. shift the governor control from manual to ... device 'REG ADJ' or device 'MAN ADJ' D. supply regulated control power to the switchboard

Last Answer : Answer: A

Description : The voltage developed by an AC generator is controlled by varying the ____________. A. speed of the prime mover B. AC excitation to the field C. DC excitation to the field D. DC excitation of the voltage regulator

Last Answer : Answer: C

Description : In the illustration, the component labeled 'EXC' is _______. EL-0003 A. a separate class II regulated DC generator for critical direct current loads B. a generator feeding the FLD ... to drive the governor for turbogenerator speed. D. the electronic driver for the switchboard metering circuits

Last Answer : Answer: B

Description : The frequency of an alternator is controlled from the main switchboard by adjusting the _____________. A. frequency meter B. voltage regulator C. governor control D. sychroscope switch

Last Answer : Answer: C

Description : Equal power factors on paralleled AC generators are maintained by an automatic _____________. A. voltage regulator B. reverse power relay C. reverse current relay D. governor control switch

Last Answer : Answer: A

Description : The cycles per second developed by the alternator aboard your vessel is determined by _____________. A. the speed of the engine driving the alternator B. the resistance applied to the field rheostat C. the synchronous speed of induction D. the adjustments made to the voltage regulator

Last Answer : Answer: A

Description : When securing an AC generator, you should FIRST ___________. A. open the generator circuit breaker B. switch the voltage regulator to 'manual' C. decrease the field excitation to minimum D. reduce the load on the unit

Last Answer : Answer: D

Description : Prior to starting an AC generator prime mover, the voltage regulator cutout switch should be placed in the __________. A. manual position B. bus neutral position C. raise voltage position D. transfer position

Last Answer : Answer: A

Description : The instantaneous reduction in voltage of an AC generator, resulting from an increase in load, and prior to the automatic voltage regulator correcting the situation, is called voltage ____________. A. droop B. drop C. dip D. regulation

Last Answer : Answer: C

Description : Section II of the circuit shown in the illustration is the ____________. EL-0085 A. voltage regulator B. filter C. rectifier D. voltage transformer

Last Answer : Answer: C

Description : Section IV of the circuit shown in the illustration is the _____________. EL-0085 A. voltage regulator B. filter C. rectifier D. voltage transformer

Last Answer : Answer: A

Description : Section III of the circuit shown in the illustration is a _____________. EL-0085 A. voltage regulator B. filter C. rectifier D. voltage transformer

Last Answer : Answer: B

Description : A switchboard for an AC electrical system requires the use of which of the following devices? A. Frequency meter. B. Ohmmeter. C. Induction voltage regulator. D. Current transformer governor.

Last Answer : Answer: A

Description : The simplest method of controlling the terminal voltage of compound-wound DC generator is with a _____________. A. hand-operated field rheostat connected in series with the shunt field circuit B. ... in series with the load D. balance coil diverting neutral current through the shunt field

Last Answer : Answer: A

Description : Silicon diodes designed for a specific reverse breakdown voltage, become useful as an electronic power supply voltage regulator, called _____________. A. tunnel diodes B. hot-carrier diodes C. compensating diodes D. Zener diodes

Last Answer : Answer: D

Description : A constant output voltage from an AC generator is maintained by the _____________. A. prime mover governor B. exciter generator C. voltage regulator D. reverse power relay

Last Answer : Answer: C

Description : Regarding an AC generator connected to the main electrical bus; as the electric load and power factor vary, a corresponding change is reflected in the generator armature reaction. These changes in ... . governor speed droop setting B. voltage regulator C. balance coil D. phase-balance relay

Last Answer : Answer: B

Description : What is Automatic Voltage regulator (AVR)?

Last Answer : AVR is an abbreviation for Automatic Voltage Regulator. It is important part in Synchronous Generators; it controls the output voltage of the generator by controlling its excitation current. Thus it can control the output Reactive Power of the Generator.

Description : What Is Automatic Voltage Regulator(avr)?

Last Answer : AVR is an abbreviation for Automatic Voltage Regulator. It is important part in Synchronous Generators, it controls the output voltage of the generator by controlling its excitation current. Thus it can control the output Reactive Power of the Generator.

Description : List the important characteristics of a voltage regulator.

Last Answer : The output voltage is fixed at a specified value, The unregulated voltage must be at least 2V more than the regulated voltage.

Description : What is a linear voltage regulator?

Last Answer : Series or linear regulator uses a power transistor connected in series between the unregulated dc input and the load and it conducts in the linear region .The output voltage is controlled by the continous voltage drop taking place across the series pass transistor. 

Description : What is a voltage regulator?

Last Answer : A voltage regulator is an electronic circuit that provides a stable dc voltage independent of the load current, temperature, and ac line voltage variations.

Description : What is Automatic Voltage regulator (AVR)?

Last Answer :  AVR is an abbreviation for Automatic Voltage Regulator.  It is important part in Synchronous Generators; it controls the output voltage of the generator by controlling its excitation current. Thus it can control the output Reactive Power of the Generator.

Description : What Is Zener Diode? What Is Voltage Regulator?

Last Answer : The breakdown region of a p-n diode can be made very sharp and almost vertical diodes with almost vertical breakdown region are known a s zener diodes. A zener diode operating in the ... . Voltage regulator: The output remains constant despite changes in the input voltage due to zener effect.

Description : What Is Zener Diode? What Is Voltage Regulator?

Last Answer : The breakdown region of a p-n diode can be made very sharp and almost vertical diodes with almost vertical breakdown region are known a s zener diodes. A zener diode operating in the ... . Voltage regulator: The output remains constant despite changes in the input voltage due to zener effect.

Description : Hat Is Zener Diode? What Is Voltage Regulator?

Last Answer : The breakdown region of a p-n diode can be made very sharp and almost vertical diodes with almost vertical breakdown region are known a s zener diodes. A zener diode operating in the breakdown ... . It is this constant voltage that has made the zener diode an important device in voltage regulation.

Description : What is Zener Diode ? What is a voltage Regulator ?

Last Answer : The breakdown region of a p n diode can be made very sharp and almost vertical Diodes with almost vertical breakdown region are known as Zever Diodes. A Zener diodes operating in the breakdown ... VOLTAGE REGULATOR : The output remains constant despite changes in input voltage due to Zever effect.  

Description : A shunt-type voltage regulator is connected in serial/parallel (which one) with the load resistance.

Last Answer : In parallel.

Description : When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease (which one) in the resistance of the regulating device.

Last Answer : An increase.

Description : The purpose of a voltage regulator is to provide an output voltage with little or no __

Last Answer : Variation.

Description : The purpose of a voltage regulator is to provide an output voltage with little or no _

Last Answer : Variation.

Description : A shunt type voltage regulator is connected in series/parallel with the load resistance.

Last Answer : Parallel

Description : When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease in the resistance of the regulating device.

Last Answer : Increase.

Description : main function of the current regulator is A. To prevent the reversal flow of current from the battery when dynamo speed is drops. B. To safeguard against flow of high currents to battery when armature develops ... . C. To prevent building up of high voltage in a circuit. D. None of the above

Last Answer : B. To safeguard against flow of high currents to battery when armature develops more current.

Description : Explain Zener diode as voltage regulator. 

Last Answer : Zener Diodes can be used to produce a stabilised voltage output with low ripple under varying load current conditions. By passing a small current through the diode from a voltage source, via a ... across the load in spite of variations in the input voltage or changes in the load current. 

Description : Sketch circuit diagram of transistorized series voltage regulator and explain its working.

Last Answer : * This regulator has a transistor in series to the Zener regulator and both in parallel to the load. The transistor works as a variable resistor, regulating its collector emitter voltage in ... of output voltage compensates the initial increase in output voltage. Thus it acts as a regulator. 

Description : …Hi,  When we supply the microcontroller we use  12V step down transformer> rectifier> filter> 5V voltage regulator. Why not use? 5V transformer> rectifier>filter only. And what voltage regulator will do in our microcontroller?

Last Answer : The powering supply voltage to a microcontroller is 5v if you use a 5v transformer if there is loss of power your output voltage will be drop in the rectifier and there will be change in voltage these can be overcome using a regulator it will give a constant output

Description : Explain with circuit diagram operation of zener diode as a voltage regulator.

Last Answer : The function of a regulator is to provide a constant output voltage to a load connected in parallel with it in spite of the ripples in the supply voltage or the variation in the load ... V0 = VZ is obtained across RL, whenever the input voltage remains within a minimum and maximum voltage.

Description : A zener voltage regulator has load requirements of 12 V and 2 A. The zener diode minimum current requirement is 0.2 A. The minimum voltage at input is 24 V. What is the required value of series resistance with source? A) 5.45 Ω B) 6 Ω C) 7.2 Ω D) 6.38 Ω  

Last Answer : A zener voltage regulator has load requirements of 12 V and 2 A. The zener diode minimum current requirement is 0.2 A. The minimum voltage at input is 24 V. What is the required value of series resistance with source? A) 5.45 Ω B) 6 Ω C) 7.2 Ω D) 6.38 Ω  

Description : The device used for voltage regulator is

Last Answer : The device used for voltage regulator is zener diode

Last Answer : The voltage regulation in magnetic amplifier type voltage regulator is effected by varying the reactance.

Description : Thyristor controlled phase angle regulator

Last Answer : Thyristor controlled phase angle regulator