A fuse is always installed in a circuit is

by

1 Answer

Answer :

A fuse is always installed in a circuit is Series.

by

Related questions

During maintenance of circuit breakers, _______________. A. always smooth roughened contact surfaces with a file B. never pass more than rated breaker current through the overload heater element C. inspect for wear and misalignment of main contacts D. assume heater elements installed are of correct size

Description : During maintenance of circuit breakers, _______________. A. always smooth roughened contact surfaces with a file B. never pass more than rated breaker current through the overload heater element C. ... wear and misalignment of main contacts D. assume heater elements installed are of correct size

Last Answer : Answer: C

The rating of fuse wire is always expressed in

Description : The rating of fuse wire is always expressed in   (a) volts (b) amperes (c) ampere-volt (d) ampere-hours 

Last Answer : The rating of fuse wire is always expressed in Amperes 

What is the difference between a fuse and a circuit breaker ?

Description : What is the difference between a fuse and a circuit breaker ?

Last Answer : Fuse : It is a type of soft metal wire which, when more than the required current flows through the wire, burns it, disconnects the electrical circuit from the source and protects the valuable ... or fault in the power supply line . This breaks the static contact and protects it from accidents.

Which covalent fuse wire is connected to the main circuit ?

Description : Which covalent fuse wire is connected to the main circuit ?

Last Answer : The fuse wire is connected to the main circuit in a class co-op.

A factory is served by a 220 V supply line. In a circuit protected by a fuse marked 10 A, the maximum number of 100 W lamps in parallel that can be tu

Description : A factory is served by a 220 V supply line. In a circuit protected by a fuse marked 10 A, the maximum number of 100 W lamps in parallel that can be tu

Last Answer : A factory is served by a 220 V supply line. In a circuit protected by a fuse marked 10 A, the maximum number of ... on, is A. 11 B. 22 C. 33 D. 66

Why will too many electrical devices operating at one time after blow a fuse or trip a circuit breaker?

Description : Why will too many electrical devices operating at one time after blow a fuse or trip a circuit breaker?

Last Answer : The load exceeds the limit of the breaker or fuse. For example a20 amp breaker on a 120 volt circuit will handle 2400 watts. Exceedthat wattage and the breaker will trip or the fuse will blow.

The fuse in an electric circuit is connected in

Description : The fuse in an electric circuit is connected in

Last Answer : series with the live wire

Which one of the following applications software’s is used to obtain an accurate root locus for? a) LISP b) MATLAB c) dBase d) Oracle Ans: B 6.Lenz devised a rule to find out direction of a)current induced in a circuit b)electromagneticdifference c)potential difference d)flow of power in fuse

Description : Which one of the following applications software’s is used to obtain an accurate root locus for? a) LISP b) MATLAB c) dBase d) Oracle Ans: B 6.Lenz devised a rule to find out direction of a)current induced in a circuit b)electromagneticdifference c)potential difference d)flow of power in fuse

Last Answer : Ans: A

What is the function of a fuse wire? (a) To prevent an unduly high electric current from passing through a circuit (b) To increase the current supply (c) To decrease the current supply (d) To stabilise the voltage

Description : What is the function of a fuse wire? (a) To prevent an unduly high electric current from passing through a circuit (b) To increase the current supply (c) To decrease the current supply (d) To stabilise the voltage

Last Answer : Ans:(a)

In an electrical circuit, a fuse is connected (a) in the live wire (b) in the neutral wire (c) in the earth wire (d) anywhere—it makes no difference

Description : In an electrical circuit, a fuse is connected (a) in the live wire (b) in the neutral wire (c) in the earth wire (d) anywhere—it makes no difference

Last Answer : Ans:(a)

The function of fuse in an electrical circuit is (a) avoid electric shocks (b) regulate the flow of current (c) break the circuit in case of overloading or short circuiting (d) switch off current

Description : The function of fuse in an electrical circuit is (a) avoid electric shocks (b) regulate the flow of current (c) break the circuit in case of overloading or short circuiting (d) switch off current

Last Answer : Ans:(c)

The fuse in an electric circuit is connected in – (1) series with neutral (2) parallel to live (3) parallel to neutral (4) series with live

Description : The fuse in an electric circuit is connected in – (1) series with neutral (2) parallel to live (3) parallel to neutral (4) series with live

Last Answer : (4) series with live Explanation: A fuse wire is a safety wire connected in series with the live wire that has high resistivity and low melting point. Fuses are always connected in ... large current supply or malfunctioning in the electric connections, it melts and breaks the electric circuit.

The fuse in our domestic electric circuit melts when there is a high rise in – (1) Inductance (2) Current (3) Resistance (4) Capacitance

Description : The fuse in our domestic electric circuit melts when there is a high rise in – (1) Inductance (2) Current (3) Resistance (4) Capacitance

Last Answer : (2) Current Explanation: In electronics and electrical engineering, a fuse is a type of low resistance resistor that acts as a sacrificial device to provide over protection, of either the load ... fuse interrupts excessive current (blows) so that further damage by overheating or fire is prevented.

A device which is used to limit the current in an electrical circuit is called a - (1) Grid (2) Fuse (3) Hub (4) Conductor

Description : A device which is used to limit the current in an electrical circuit is called a - (1) Grid (2) Fuse (3) Hub (4) Conductor

Last Answer : (2) Fuse Explanation: A fuse places a limit on the amount of current that can be drawn by an electric circuit by opening (blowing or melting) when the current exceeds a preset limit. This protects the circuit and the surroundings from fire or damage in the case of an overload or short circuit.

Which of the following precautions should be taken when a blown fuse, rated at 10 amperes, is replaced? A. Short out the fuse before removing it from the circuit. B. Use needle-nose pliers to remove fuse from the circuit. C. Replace blown fuse with one of equal voltage and ampere capacity. D. Fuses of 10 ampere rating and less are virtually harmless when energized and may be handled freely.

Description : Which of the following precautions should be taken when a blown fuse, rated at 10 amperes, is replaced? A. Short out the fuse before removing it from the circuit. B. Use needle-nose pliers to ... D. Fuses of 10 ampere rating and less are virtually harmless when energized and may be handled freely.

Last Answer : Answer: C

If a voltage tester is being used to check for defective fuses in the circuit, shown in the illustration, which of the readings will indicate that fuse #2 is open? EL-0062 A. C-B full voltage B. A-D full voltage C. A-D no voltage D. C-B no voltage

Description : If a voltage tester is being used to check for defective fuses in the circuit, shown in the illustration, which of the readings will indicate that fuse #2 is open? EL-0062 A. C-B full voltage B. A-D full voltage C. A-D no voltage D. C-B no voltage

Last Answer : Answer: C

In the lighting distribution circuit shown in the illustration, if all switches are closed and fuse 'F2' were to open, all lights on branches ____________. EL-0013 A. '1', '2', and '3' would go out B. '1' and '3' would would burn dimly, while branch '2' would burn normally C. '1', '2', and '3' would burn dimly D. '1' and '3' would go out, while branch '2' would remain lit

Description : In the lighting distribution circuit shown in the illustration, if all switches are closed and fuse 'F2' were to open, all lights on branches ____________. EL-0013 A. '1', '2', and '3' would go out B. '1' ... and '3' would burn dimly D. '1' and '3' would go out, while branch '2' would remain lit

Last Answer : Answer: D

The schematic diagram shown in the illustration uses symbol 'A' to represent a/an _________. EL-0011 A. non-renewable fuse link B. circuit breaker coil C. overload relay coil D. thermal overload heater

Description : The schematic diagram shown in the illustration uses symbol 'A' to represent a/an _________. EL-0011 A. non-renewable fuse link B. circuit breaker coil C. overload relay coil D. thermal overload heater

Last Answer : Answer: D

In order to safely carry out repairs to a generator circuit breaker, it must be isolated from the bus. This is accomplished by opening the _____________. A. reverse power relay B. bus disconnect link C. generator bus fuse connections D. power directional relay

Description : In order to safely carry out repairs to a generator circuit breaker, it must be isolated from the bus. This is accomplished by opening the _____________. A. reverse power relay B. bus disconnect link C. generator bus fuse connections D. power directional relay

Last Answer : Answer: B

If an electric motor fails to start, you should FIRST check the _____________. A. phase sequence B. ampere load C. fuse or circuit breaker D. line frequency

Description : If an electric motor fails to start, you should FIRST check the _____________. A. phase sequence B. ampere load C. fuse or circuit breaker D. line frequency

Last Answer : Answer: C

When testing for blown fuses in a three-phase supply circuit to a motor, you should first ___________________. A. apply the megger across the tops of the line fuses B. apply an ammeter diagonally across the top of the first line fuse and the bottom of the third line fuse C. apply the voltage tester across the bottoms of the line fuses D. ensure the circuit is de-energized, and then use a continuity tester

Description : When testing for blown fuses in a three-phase supply circuit to a motor, you should first ___________________. A. apply the megger across the tops of the line fuses B. apply an ammeter diagonally across ... of the line fuses D. ensure the circuit is de-energized, and then use a continuity tester

Last Answer : Answer: D

When an AC or a DC motor fails to start, the FIRST step in troubleshooting should be to check the ____________. A. motor windings for obvious opens B. motor controller leads for continuity C. fuse or circuit breaker D. motor controller leads for grounds

Description : When an AC or a DC motor fails to start, the FIRST step in troubleshooting should be to check the ____________. A. motor windings for obvious opens B. motor controller leads for continuity C. fuse or circuit breaker D. motor controller leads for grounds

Last Answer : Answer: C

In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, Federal Regulations (46 CFR) require the maximum fuse rating for that branch to be _________. EL-0013 A. 80% of the connected load B. 15 amps C. 20 amps D. 30 amps

Description : In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, Federal Regulations (46 CFR) require the maximum fuse rating for that branch to be _________. EL-0013 A. 80% of the connected load B. 15 amps C. 20 amps D. 30 amps

Last Answer : Answer: C

A circuit with a blown fuse would be described as a/an _____________. A. short circuit B. open circuit C. bonded circuit D. grounded circuit

Description : A circuit with a blown fuse would be described as a/an _____________. A. short circuit B. open circuit C. bonded circuit D. grounded circuit

Last Answer : Answer: B

In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, 46 CFR requires the maximum fuse rating for that branch to be _________. EL-0013 A. 15 amps B. 80% of the connected load C. 20 amps D. 30 amps

Description : In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, 46 CFR requires the maximum fuse rating for that branch to be _________. EL-0013 A. 15 amps B. 80% of the connected load C. 20 amps D. 30 amps

Last Answer : Answer: C

If a fuse of correct size and type blows frequently, ________________. A. try the next higher amperage rating B. try the next lower amperage rating C. look for trouble within the circuit D. reduce the applied voltage 10%

Description : If a fuse of correct size and type blows frequently, ________________. A. try the next higher amperage rating B. try the next lower amperage rating C. look for trouble within the circuit D. reduce the applied voltage 10%

Last Answer : Answer: C

You are using a mechanical voltage tester to check the fuses in a three-phase circuit supplying an electric motor. For which of the following reasons must the motor be stopped during the test? A. Testing an energized circuit presents a hazard to the testing personnel. B. A faulty fuse could go undetected with the motor energized. C. Reversed polarity of the circuit would be indicated by the voltage tester with the circuit energized. D. All of the above.

Description : You are using a mechanical voltage tester to check the fuses in a three-phase circuit supplying an electric motor. For which of the following reasons must the motor be stopped during the test? A. ... circuit would be indicated by the voltage tester with the circuit energized. D. All of the above.

Last Answer : Answer: B

An instantaneous-trip-type fuse will _____________. A. open as soon as the load current exceeds its set point B. allow a preset delay between overcurrent and melting C. open a circuit by using a time delay element with a magnetic trip D. reset itself when the overcurrent is corrected

Description : An instantaneous-trip-type fuse will _____________. A. open as soon as the load current exceeds its set point B. allow a preset delay between overcurrent and melting C. open a circuit by using a time delay element with a magnetic trip D. reset itself when the overcurrent is corrected

Last Answer : Answer: A

Component 'C' in section 'I' shown in the illustration represent ____________. EL-0093 A. a selectable holding coil arrangement B. a 'fuse blown' indicator circuit C. 'reset' and 'trouble' lamps D. a handset with switch and voice elements

Description : Component 'C' in section 'I' shown in the illustration represent ____________. EL-0093 A. a selectable holding coil arrangement B. a 'fuse blown' indicator circuit C. 'reset' and 'trouble' lamps D. a handset with switch and voice elements

Last Answer : Answer: D

Which of the following conditions is most likely to occur if a single element fuse were used to replace a blown dual element fuse in a motor controller circuit? A. The fuse will blow when the motor is started. B. The fuse works, but overheats at high motor loads. C. The motor runs at reduced voltage. D. The motor runs normally.

Description : Which of the following conditions is most likely to occur if a single element fuse were used to replace a blown dual element fuse in a motor controller circuit? A. The fuse will blow when the motor ... overheats at high motor loads. C. The motor runs at reduced voltage. D. The motor runs normally.

Last Answer : Answer: A

Before touching a small capacitor connected to a de-energized circuit, or even one that is completely disconnected, you should ____________. A. gently tap the body with a screwdriver B. tag it with a de-energized tag C. be equipped with an insulated fuse puller D. short circuit the terminals to make sure that the capacitor is discharged

Description : Before touching a small capacitor connected to a de-energized circuit, or even one that is completely disconnected, you should ____________. A. gently tap the body with a screwdriver B. tag it ... insulated fuse puller D. short circuit the terminals to make sure that the capacitor is discharged

Last Answer : Answer: D

Which of the listed items will stop a motor due to a reduction in voltage and restart it when the voltage is restored to normal? A. Low voltage protection circuit B. Non-renewable link fuse C. Renewable link fuse D. Low voltage release circuit

Description : Which of the listed items will stop a motor due to a reduction in voltage and restart it when the voltage is restored to normal? A. Low voltage protection circuit B. Non-renewable link fuse C. Renewable link fuse D. Low voltage release circuit

Last Answer : Answer: D

The part of a fuse that melts and opens the circuit is made of _____________. A. copper and antimony B. steel and babbitt C. aluminum or beryllium alloy D. zinc or an alloy of tin and lead

Description : The part of a fuse that melts and opens the circuit is made of _____________. A. copper and antimony B. steel and babbitt C. aluminum or beryllium alloy D. zinc or an alloy of tin and lead

Last Answer : Answer: D

A delayed-action fuse is most frequently used in which of the listed circuits? A. Lighting circuit B. Motor circuit C. Electric heater circuit D. Radar circuit

Description : A delayed-action fuse is most frequently used in which of the listed circuits? A. Lighting circuit B. Motor circuit C. Electric heater circuit D. Radar circuit

Last Answer : Answer: B

A circuit breaker differs from a fuse in that a circuit breaker _____________. A. melts and must be replaced B. is enclosed in a tube of insulating material with metal ferrules at each end C. gives no visual indication of having opened the circuit D. trips to break the circuit and may be reset

Description : A circuit breaker differs from a fuse in that a circuit breaker _____________. A. melts and must be replaced B. is enclosed in a tube of insulating material with metal ferrules at each end C. gives no visual indication of having opened the circuit D. trips to break the circuit and may be reset

Last Answer : Answer: D

A circuit breaker and a fuse have a basic similarity in that they both _____________. A. can be reset to energize the circuit B. should open the circuit when overloaded C. will burn out when an over current flow develops D. all of the above

Description : A circuit breaker and a fuse have a basic similarity in that they both _____________. A. can be reset to energize the circuit B. should open the circuit when overloaded C. will burn out when an over current flow develops D. all of the above

Last Answer : Answer: B

Why link is provided in neutral of an ac circuit and fuse in phase of ac circuit?

Description : Why link is provided in neutral of an ac circuit and fuse in phase of ac circuit?

Last Answer : Link is provided at a Neutral common point in the circuit from which various connections are taken for the individual control circuit and so it is given in a link form to withstand high Amps. ... So if any malfunction happens the fuse connected in the particular control circuit alone will blow off.

Why link is provided in neutral of an ac circuit and fuse in phase of ac circuit?

Description : Why link is provided in neutral of an ac circuit and fuse in phase of ac circuit?

Last Answer : A:Link is provided at a Neutral common point in the circuit from which various connection are taken for the individual control circuit and so it is given in a link form to withstand high Amps ... .So if any malfunction happen the fuse connected in the particular control circuit alone will blow off.

Differentiate between a fuse and a circuit breaker.

Description : Differentiate between a fuse and a circuit breaker.

Last Answer : Fuse is a low current interrupting device. It is a copper or an aluminium wire. Circuit breaker is a high current interrupting device and it act as a switch under normal operating conditions.

Why link is provided in neutral of an ac circuit and fuse in phase of ac circuit?

Description : Why link is provided in neutral of an ac circuit and fuse in phase of ac circuit?

Last Answer :  Link is provided at a Neutral common point in the circuit from which various connections are taken for the individual control circuit and so it is given in a link form to withstand high Amps.  ... Supply is on than due to open or break Neutral Voltage is increase and equipment may be damage.

Which of the following is the least expensive protection for overcurrent is low voltage system ? (a) Rewireable fuse (b) Isolator (c) Oil circuit breaker (d) Air break circuit breaker (e) None of the above

Description : Which of the following is the least expensive protection for overcurrent is low voltage system ? (a) Rewireable fuse (b) Isolator (c) Oil circuit breaker (d) Air break circuit breaker (e) None of the above

Last Answer : (a) Rewireable fuse

The main function of a fuse is to (a) protect the line (b) open the circuit (c) protect the appliance (d) prevent excessive currents (e) none of the above

Description : The main function of a fuse is to (a) protect the line (b) open the circuit (c) protect the appliance (d) prevent excessive currents (e) none of the above

Last Answer : (d) prevent excessive currents

The fuse in an electric circuit is connected in (1) series with neutral (2) parallel to live (3) parallel to neutral (4) series with live

Description : The fuse in an electric circuit is connected in (1) series with neutral (2) parallel to live (3) parallel to neutral (4) series with live 

Last Answer : series with live

A device which is used to limit the current in an electrical circuit is called a (1) Grid (2) Fuse (3) Hub (4) Conductor

Description : A device which is used to limit the current in an electrical circuit is called a (1) Grid (2) Fuse (3) Hub (4) Conductor 

Last Answer : Fuse

A fuse in a motor circuit provides protection against?

Last Answer : A fuse in a motor circuit provides protection against short-circuit and overload.

When changing fuses, you should always _____________. A. wear rubber boots B. use a fuse puller C. stand on a rubber mat D. wear safety glasses

Description : When changing fuses, you should always _____________. A. wear rubber boots B. use a fuse puller C. stand on a rubber mat D. wear safety glasses

Last Answer : Answer: B

When replacing fuses, always make sure _______________. A. to stand on a rubber mat and use rubber gloves B. to use insulated pliers or screwdriver C. the fuse clips are straight, tight, and in good contact D. to increase the fuse rating 10% to guard against 'nuisance blowing'

Description : When replacing fuses, always make sure _______________. A. to stand on a rubber mat and use rubber gloves B. to use insulated pliers or screwdriver C. the fuse clips are straight, tight, and in good contact D. to increase the fuse rating 10% to guard against 'nuisance blowing'

Last Answer : Answer: C

A tubular fuse should always be removed from a fuse panel with _____________. A. a screwdriver B. a pair of insulated metal pliers C. any insulated object D. fuse pullers

Description : A tubular fuse should always be removed from a fuse panel with _____________. A. a screwdriver B. a pair of insulated metal pliers C. any insulated object D. fuse pullers

Last Answer : Answer: D