What is RMS value ?

What is RMS value ?
by

1 Answer

Answer :

If a certain amount of heat is generated in a certain amount of DC current flows through a certain register at a certain time , if the same amount of heat is generated in the current flowing through the same resistor at the same time, then that DC current is called the effective or RMS value of AC current.
by

Related questions

What happens if the value of power factor is low ?

Description : What happens if the value of power factor is low ?

Last Answer : ( a) Current flows more , ( b) Copper loss increases , ( c) Heat increases , ( d) Output decreases , ( e) Voltage drop increases , ( f) Different electrical machinery heats up quickly. , ( G) The life span of various electrical machinery and appliances is reduced.

What is the value of voltage and current of transformer ?

Description : What is the value of voltage and current of transformer ?

Last Answer : The value of voltage and current of the transformer depends on the number of patches of wires in the transformer.

What is average value ?

Description : What is average value ?

Last Answer : The average amount of charge transferred by a certain amount of DC current flowing through a particular circuit at a given time, the same amount of charge that is transferred through the same circuit at the same time বলে is called the average value of that AC current.

What is the value of power factor ?

Description : What is the value of power factor ?

Last Answer : The value of power factor is Cos Theta

The RMS value of a sine-wave current may also be expressed as the _____________. A. average value B. maximum value C. effective value D. instantaneous value

Description : The RMS value of a sine-wave current may also be expressed as the _____________. A. average value B. maximum value C. effective value D. instantaneous value

Last Answer : Answer: C

What does the Voltmeter in AC mode show? Is it RMS value or peak value?

Description : What does the Voltmeter in AC mode show? Is it RMS value or peak value?

Last Answer : Multimeter in AC mode shows RMS value of the voltage or current. Also when it is DC mode it will show the RMS value only.

Find the power of a wave given that the RMS value of E and H are 6 and 4.5 respectively. a) 24 b) 27 c) 29 d) 32

Description : Find the power of a wave given that the RMS value of E and H are 6 and 4.5 respectively. a) 24 b) 27 c) 29 d) 32

Last Answer : b) 27

Alternating current measured in a transmission line will be a) Peak value b) Average value c) RMS value d) Zero

Description : Alternating current measured in a transmission line will be a) Peak value b) Average value c) RMS value d) Zero

Last Answer : c) RMS value

In a half wave rectifier the rms value of AC component of the waves (a) Zero (b) Equal to DC value (c) More than DC value (d) Less than DC value

Description : In a half wave rectifier the rms value of AC component of the waves (a) Zero (b) Equal to DC value (c) More than DC value (d) Less than DC value

Last Answer : b) Equal to DC value

6 The value of flux involved in the emf equation of a transformer is A. rms value B. rms value C. Maximum value D. Instantaneous value

Description : 6 The value of flux involved in the emf equation of a transformer is A. rms value B. rms value C. Maximum value D. Instantaneous value

Last Answer : C) maximum value

Write the relation between RMS value and Average value.

Description : Write the relation between RMS value and Average value.

Last Answer : The ratio of RMS value to average value is called the form factor of an alternating quantity.

Define RMS value and Average value of AC waveform.

Description : Define RMS value and Average value of AC waveform.

Last Answer : 1. RMS value:- For an alternating current, the RMS value is defined as that value of steady current (DC) which produces the same heat or power as is produced by the alternating current during the ... by averaging all the instantaneous values of its wave over a period of half cycle. Iav=0.637 Imax

Define following terms used in A.C. circuits : (i) Cycle (ii) Rms value (iii) Phase difference (iv) Average value

Description : Define following terms used in A.C. circuits : (i) Cycle (ii) Rms value (iii) Phase difference (iv) Average value

Last Answer : (i) Cycle:   A complete set of variation of an alternating quantity which is repeated at regular interval of time is called as a cycle. OR  Each repetition of an alternating quantity ... charge as is transferred by the alternating current during the same time under the same conditions. 

Define : i) Maximum Value ii) RMS Value of ac supply

Description : Define : i) Maximum Value ii) RMS Value of ac supply

Last Answer : i) Maximum Value :- The maximum or peak value attained by an alternating quantity during positive or negative half cycle, is called maximum value or peak value.  ii) RMS Value of ac ... as produced by the alternating current when flowing through the same resistance and for the same time. 

Define : i) Average value ii) RMS value of an AC Wave.

Description : Define : i) Average value ii) RMS value of an AC Wave.

Last Answer : i) Average value: The average value is defined as the average of all instantaneous values during one alternation . That is, the ratio of the sum of all considered instantaneous values to the ... as produced by the alternating current when flowing through the same resistance for the same time.

RMS value formula

Description : RMS value formula

Last Answer : RMS value formula

Define RMS value.

Description : Define RMS value.

Last Answer : RMS Value of Sinusoidal AC Waveform: The RMS value is the Root Mean Square value. It is defined as the square root of the mean value of the squares of the alternating quantity over one cycle ... power or heat as is produced by the alternating current during the same time under the same conditions.

The rms value of the current in a wire which carries a d.c. current of 10 A and a sinusoidal alternating current

Description : The rms value of the current in a wire which carries a d.c. current of 10 A and a sinusoidal alternating current of peak value 20 A is  (A) 10 A (B) 14.14 A (C) 15 A (D) 17.32 A

Last Answer : The rms value of the current in a wire which carries a d.c. current of 10 A and a sinusoidal alternating current of peak value 20 A is 17.32 A

If the peak value of a sine wave is 30 V, the rms value is?

Description : If the peak value of a sine wave is 30 V, the rms value is? A.19.08 V B.7.07 V C.0.707 V D.23.10 V

Last Answer : If the peak value of a sine wave is 30 V, the rms value is? A.19.08 V B.7.07 V C.0.707 V D.23.10 V

RMS value of rectangular wave of period T, having a value of +V for a duration T1(<T) and -V for the duration...

Description : RMS value of rectangular wave of period T, having a value of +V for a duration T1(

Last Answer : a

What is the meaning of RMS value?

Description : What is the meaning of RMS value?

Last Answer : RMS value means root mean square value. It is 0.707 times peak value of voltage or current. The ammeter and voltmeter records this rms value. RMS value for sine wave is more than average value. RMS ... same amount of heat as produce by AC when AC is flowing through the same resistance for same time.

What is the conductivity of molar ?

Description : What is the conductivity of molar ?

Last Answer : The density of a solution as cm. When one mole of electrolytic substance is dissolved in it, the conductivity obtained by multiplying it by the relative conductivity of the solution is called molecular conductivity of the solution .

How do I purchase a product ?

Description : How do I purchase a product ?

Last Answer : From Alibaba you can purchase products by paying MASTER CARD or through bank.

What is an analog signal ?

Description : What is an analog signal ?

Last Answer : Signals whose values ​​change continuously are called analog signals. For example- voltage of electricity supplied to the house.

What is Zener Diod ?

Description : What is Zener Diod ?

Last Answer : Zener diode is a special type of diode which, like ordinary diode, not only conducts current in the forward direction , but also in the opposite direction if the voltage exceeds the level of breakdown ... diode is to use the shunt regulator and the voltage reference as the voltage of the circuit.

What is the multiplying factor of shunt ?

Description : What is the multiplying factor of shunt ?

Last Answer : Answer : The ratio of load or matte current to ammeter current is called shunt multiplying power.

What is ammeter shunt ?

Description : What is ammeter shunt ?

Last Answer : A small amount of radial coupling in parallel with the coil to increase the range of ammeter is called ammeter shunt.

What is short circuit current ?

Description : What is short circuit current ?

Last Answer : Answer : A fault in an electrical system whose current, before or after the current flows through the load, is combined with one or more phases of neutral current which causes more current to flow than normal. The current is called short circuit current.

What is a current limiting reactor ? How many types and what are they ?

Description : What is a current limiting reactor ? How many types and what are they ?

Last Answer : Answer : A current limiting reactor is basically an inductive coil which limits the short circuit current by providing inductive reactance when required. Types: 1. Based on the structure- a) Dry type ... reactor. Basbar reactors are again of 2 types- a) Ring system reactor b) Tiber system reactor

What is the method of diagnosing short circuit current ?

Description : What is the method of diagnosing short circuit current ?

Last Answer : There are three methods for determining short circuit current , namely- 1) Ohmic method 2) Per unit method 3.) Percentage reactance method.

What are symmetrical and asymmetrical faults ?

Description : What are symmetrical and asymmetrical faults ?

Last Answer : Symmetrical Fault: The same amount in each phase due to the float in the electrical system. The fault that causes hot current to flow is called semantic fault. Circuit breaker ratings are determined by ... through each fan is called an asymmetrical fault. The relay is set via asymmetrical font.

What is Basbar and Bas Kaplar ?

Description : What is Basbar and Bas Kaplar ?

Last Answer : Basbar : Basbar is basically a sheet or color of copper or aluminum. It is the job of the bus driver to deliver power to one or more lads with power from one or more cables. Bus ... is basically a combination of circuit breaker and isolator. There are fire proof walls around the bus coupler.

Why is the busbar sectionalized ?

Description : Why is the busbar sectionalized ?

Last Answer : Answer : If an error occurs in any part of the busbar, the operation of the entire busbar system will not stop. The maximum success of this system is due to the interconnection of different sections of the circuit and the smooth distribution in the outgoing circuit.

title : _

Description : title : _

Last Answer : Basbar is a type of copper and aluminum conductive sheet or mata rod , which collects electrical energy from one or more circuits and distributes that energy through one or more circuits.

Write different font names or different short circuit font names ?

Description : Write different font names or different short circuit font names ?

Last Answer : There are two main types of short circuit faults. Namely- 1. Semantic faults and 2. Asymmetrical font Symmetrical fault - a) Short circuit three phases together b) Short circuit asymmetrical fault with three ... result c) Double line to ground font d) Two phase one Circuit and third phase earth.

What is Electrical Fault ? What is the cause of the fault ?

Description : What is Electrical Fault ? What is the cause of the fault ?

Last Answer : Answer : Fault: When two or more conductors come in contact with each other while operating at normal voltage difference, the result is said to be organized. Causes of Fault: Faults are organized due to ... loss of line c) Lightning charge d) Voltage drop e) Loss of unbalance and stability etc.

What features should a switchgear have ?

Description : What features should a switchgear have ?

Last Answer : Switchgear should have the following characteristics- a) Sensitivity b) Detection ability c) Reliability d) High speed e) Durability. F) Expansion advantage g) Simplicity.

What are the components of switch gear ?

Description : What are the components of switch gear ?

Last Answer : The components of switch gear are: circuit breaker , relay , instrument transformer , housing , conductor etc.

What do you mean by switchgear ?

Description : What do you mean by switchgear ?

Last Answer : Answer : Switch gear does not mean a single corner object. It refers to the position of the electromagnetic system, including the connective , isolating , and maintenance equipment of normal activity .

What is an Earth Electrode ?

Description : What is an Earth Electrode ?

Last Answer : Puta metal part in the soil which connects to the soil is called earth electrode. Thank you all for today's electrical questions and answers.

What is Earthing Lead ?

Description : What is Earthing Lead ?

Last Answer : The wire that connects the earth continuity wire and the earth electrode is called the earthing lead.

What earthing is done in hilly areas ?

Description : What earthing is done in hilly areas ?

Last Answer : Sheet earthing is done in hilly areas. Shit electrodes are placed by digging trenches on the slopes of the hill.

What should be the size of rod earthing ?

Description : What should be the size of rod earthing ?

Last Answer : In case of iron or steel rod the diameter is 16 mm but in case of copper rod it is 12.5 mm. In both cases the length is at least 2.5 m. Is to be.

What does earth continuity mean ?

Description : What does earth continuity mean ?

Last Answer : The conduction wire that connects the earthing lead to the metal cover of electrical furniture, appliances, or wiring is called the earth continuity wire.

Which earthing is less expensive ?

Description : Which earthing is less expensive ?

Last Answer : Rod earthing is the least expensive. Because the soil does not have to be eroded, the cost is less than other earthing.

What should be the size of the pipe electrode ?

Description : What should be the size of the pipe electrode ?

Last Answer : The size of the pipe electrode should be 36 mm diameter 2 to 2.75 m long galvanized iron or steel pipe.

How many types of earthing and what are they ?

Description : How many types of earthing and what are they ?

Last Answer : There are two types of earthing , namely _ a) system earthing b) equipment earthing.

What are the essential elements for earthing ?

Description : What are the essential elements for earthing ?

Last Answer : They are _ a) earthen continuity b) earthing lead c) earthy electrode

What is the best earthing method ?

Description : What is the best earthing method ?

Last Answer : Pipe earthing method is best. This is because it is less expensive and when the soil dries out in the dry season , regular earthing can be done by pouring water through the pipes.