What is meant by Voltmeter & Ammeter ?

What is meant by Voltmeter & Ammeter ?
by

1 Answer

Answer :

Voltmeter measures the voltage of any load or any line and the voltmeter has to be connected parallel to the load. The ammeter measures the current flowing through a load or the current of an electrical line. The ammeter is connected in series with the load.
by

Related questions

What if I connect to voltmeter series ?

Description : What if I connect to voltmeter series ?

Last Answer : If connected to the volt meter series, no text can be found on the meter. Because the internal resistance of the voltmeter is infinite.

What is ammeter shunt ?

Description : What is ammeter shunt ?

Last Answer : A small amount of radial coupling in parallel with the coil to increase the range of ammeter is called ammeter shunt.

How range of A.C. ammeter & A.C. voltmeter is extended? Draw suitable diagram.

Description : How range of A.C. ammeter & A.C. voltmeter is extended? Draw suitable diagram.

Last Answer : Extension of A.C. Ammeter Range: The range of a.c. ammeter can be extended by using CT, the arrangement is shown in figure. The CT is current transformer having less number of primary turns carrying high ... high magnitude of source voltage. In this way range of a.c. voltmeter can be extended.

What are the physical quantities measured with voltmeter and ammeter ?

Description : What are the physical quantities measured with voltmeter and ammeter ?

Last Answer : : The voltage difference between two points of a circuit is measured with a voltmeter. And the flow rate of an electric circuit is measured with an ammeter.

How to connect voltmeter and ammeter to circuit ?

Description : How to connect voltmeter and ammeter to circuit ?

Last Answer : : A voltmeter is connected in parallel with the two points of voltage circuit to measure the voltage difference. Again, to measure the flow rate of an electric circuit, ammeters are added to the electromagnetic circuit.

A voltmeter of range 2 V and resistance `300 Omega` cannot be converted into ammeter of range

Description : A voltmeter of range 2 V and resistance `300 Omega` cannot be converted into ammeter of range

Last Answer : A voltmeter of range 2 V and resistance `300 Omega` cannot be converted into ammeter of range A. `1 A` B. `1 mA` C. `100 mA` D. `10 mA`

A milli voltmeter of 25 milli volt range is to be converted into an ammeter of 25 ampere range. The value (in ohm) of necessary shunt will be

Description : A milli voltmeter of 25 milli volt range is to be converted into an ammeter of 25 ampere range. The value (in ohm) of necessary shunt will be

Last Answer : A milli voltmeter of 25 milli volt range is to be converted into an ammeter of 25 ampere range. The value (in ohm) ... 001` B. `0.01` C. 1 D. `0.05`

In the circuit shown in figure ammeter and voltmeter are ideal. If `E=4 V,R=9Omega` and `r=1Omega` then readings of ammeter and voltmeter are

Description : In the circuit shown in figure ammeter and voltmeter are ideal. If `E=4 V,R=9Omega` and `r=1Omega` then readings of ammeter and voltmeter are

Last Answer : In the circuit shown in figure ammeter and voltmeter are ideal. If `E=4 V,R=9Omega` and `r=1Omega` then readings of ... V C. 3 A, 4 V D. 4 A, 4 V

In the circuit shown here, the readings of the ammeter and voltmeter are

Description : In the circuit shown here, the readings of the ammeter and voltmeter are

Last Answer : In the circuit shown here, the readings of the ammeter and voltmeter are A. 6 A, 60 V B. `0.6` A, 6 V C. 6 A, 6 V D. 6/11 A, 6/11 V

An ammeter and a voltmeter of resistance `R` connected in seires to an electric cell of negligible internal resistance. Their readings are `A` and `V`

Description : An ammeter and a voltmeter of resistance `R` connected in seires to an electric cell of negligible internal resistance. Their readings are `A` and `V`

Last Answer : An ammeter and a voltmeter of resistance `R` connected in seires to an electric cell of negligible ... increase D. A will increase and V will decrease

By mistake, a voltmeter is connected in series and an ammeter is connected in parallel, with a resistance in an electrical circuit. What will happen t

Description : By mistake, a voltmeter is connected in series and an ammeter is connected in parallel, with a resistance in an electrical circuit. What will happen t

Last Answer : By mistake, a voltmeter is connected in series and an ammeter is connected in parallel, with a ... be damaged D. Only the voltmeter will be damaged

Conversion of heat into electrical er is achieved by using – (1) Ammeter (2) Hydrometer (3) Voltmeter (4) Thermocouple

Description : Conversion of heat into electrical er is achieved by using – (1) Ammeter (2) Hydrometer (3) Voltmeter (4) Thermocouple

Last Answer : (4) Thermocouple Explanation: Thermoelectric generators convert thermal energy into electricity by using heat from the body - or any object with a temperature gradient - as their energy source. ... energy into electricity. Bismuth telluride and its alloys are commonly used in thermocouples.

Conductor resistance may be INDIRECTLY measured by using a/an _____________. A. voltmeter only B. ammeter only C. voltmeter and an ammeter D. ohmmeter only

Description : Conductor resistance may be INDIRECTLY measured by using a/an _____________. A. voltmeter only B. ammeter only C. voltmeter and an ammeter D. ohmmeter only

Last Answer : Answer: C

A multimeter may be damaged by taking a _____________. A. voltage reading while in the ammeter mode B. current reading while in the voltmeter mode C. resistance reading while in the ammeter mode D. resistance reading while in the voltmeter mode

Description : A multimeter may be damaged by taking a _____________. A. voltage reading while in the ammeter mode B. current reading while in the voltmeter mode C. resistance reading while in the ammeter mode D. resistance reading while in the voltmeter mode

Last Answer : Answer: A

You are calibrating a multimeter using internal batteries to supply power for resistance measurements. However, you are unable to adjust the pointer to 'zero' using the adjustment knob. Therefore, you should _____________. A. replace the batteries in the instrument B. measure resistance by dividing the voltmeter indication by the ammeter indication C. set the pointer using a bridge D. change scales to the R X 100 scale and adjust using the 'zero ohms' adjusting knob

Description : You are calibrating a multimeter using internal batteries to supply power for resistance measurements. However, you are unable to adjust the pointer to 'zero' using the adjustment knob. Therefore, you should ... change scales to the R X 100 scale and adjust using the 'zero ohms' adjusting knob

Last Answer : Answer: A

An internal resistance is placed in series with the meter movement of which of the following instruments? A. AC ammeter B. DC ammeter C. DC voltmeter D. Frequency meter

Description : An internal resistance is placed in series with the meter movement of which of the following instruments? A. AC ammeter B. DC ammeter C. DC voltmeter D. Frequency meter

Last Answer : Answer: C

The RPM of an AC generator can be measured with a/an _____________. A. ammeter B. voltmeter C. vibrating reed meter D. synchroscope

Description : The RPM of an AC generator can be measured with a/an _____________. A. ammeter B. voltmeter C. vibrating reed meter D. synchroscope

Last Answer : Answer: C

Which of the instruments listed could be use to locate a grounded field coil in a synchronous motor? A. Ammeter B. Voltmeter C. Megohmmeter D. Frequency meter

Description : Which of the instruments listed could be use to locate a grounded field coil in a synchronous motor? A. Ammeter B. Voltmeter C. Megohmmeter D. Frequency meter

Last Answer : Answer: C

A useful instrument for checking A.C. motor performance by measuring possible unbalanced currents is the _____________. A. hand or battery-operated megger B. vibrating-reed frequency meter C. hook-on voltmeter-ammeter D. D'Arsonval iron-vane probe

Description : A useful instrument for checking A.C. motor performance by measuring possible unbalanced currents is the _____________. A. hand or battery-operated megger B. vibrating-reed frequency meter C. hook-on voltmeter-ammeter D. D'Arsonval iron-vane probe

Last Answer : Answer: C

Which of the following meters uses a shunt connected in series with the load, but parallel with the meter movement? A. voltmeter B. power factor meter C. wattmeter D. ammeter

Description : Which of the following meters uses a shunt connected in series with the load, but parallel with the meter movement? A. voltmeter B. power factor meter C. wattmeter D. ammeter

Last Answer : Answer: D

To determine the state of charge of a nickel-cadmium battery, you would use a/an _____________. A. voltmeter B. hydrometer C. ammeter D. potentiometer

Description : To determine the state of charge of a nickel-cadmium battery, you would use a/an _____________. A. voltmeter B. hydrometer C. ammeter D. potentiometer

Last Answer : Answer: A

The basic meter movement responds to the flow of current through its coil. Therefore, this meter movement may be used as a/an _____________. A. voltmeter by placing a resistance in parallel with the coil B. ohmmeter by placing another meter movement in parallel with the coil C. wattmeter by placing a battery in parallel with the coil D. ammeter by placing a low resistance in parallel with the coil

Description : The basic meter movement responds to the flow of current through its coil. Therefore, this meter movement may be used as a/an _____________. A. voltmeter by placing a resistance in parallel with the ... in parallel with the coil D. ammeter by placing a low resistance in parallel with the coil

Last Answer : Answer: D

Which of the listed meters uses a shunt connected in series with the load, but parallel with the meter movement? A. Voltmeter B. Power factor meter C. Ammeter D. Wattmeter

Description : Which of the listed meters uses a shunt connected in series with the load, but parallel with the meter movement? A. Voltmeter B. Power factor meter C. Ammeter D. Wattmeter

Last Answer : Answer: C

Which of the instruments listed should always be connected in series with a circuit? A. Ammeter B. Megohmmeter C. Wattmeter D. Voltmeter

Description : Which of the instruments listed should always be connected in series with a circuit? A. Ammeter B. Megohmmeter C. Wattmeter D. Voltmeter

Last Answer : Answer: A

In order to increase its range of measurement, a resistance would be placed in series with which of the following instruments? A. DC voltmeter B. DC ammeter C. frequency meter D. power factor meter

Description : In order to increase its range of measurement, a resistance would be placed in series with which of the following instruments? A. DC voltmeter B. DC ammeter C. frequency meter D. power factor meter

Last Answer : Answer: A

A switchboard, for a AC electrical distribution system, will be provided with which of the following components? A. Frequency meter. B. Ammeter C. Voltmeter D. All of the above

Description : A switchboard, for a AC electrical distribution system, will be provided with which of the following components? A. Frequency meter. B. Ammeter C. Voltmeter D. All of the above

Last Answer : Answer: D

To test the state of charge of a nickel-cadmium battery, you should use a/an ____________. A. ammeter B. voltmeter C. hydrometer D. potentiometer

Description : To test the state of charge of a nickel-cadmium battery, you should use a/an ____________. A. ammeter B. voltmeter C. hydrometer D. potentiometer

Last Answer : Answer: B

A resistance in a circuit of unknown value is to be tested using the voltmeter/ammeter method. Therefore, the meters should be connected with _____________. A. both meters in series with the resistance B. both meters in parallel with the resistance C. the ammeter in series and the voltmeter in parallel with the resistance D. the ammeter in parallel and the voltmeter in series with the resistance

Description : A resistance in a circuit of unknown value is to be tested using the voltmeter/ammeter method. Therefore, the meters should be connected with _____________. A. both meters in series with the ... parallel with the resistance D. the ammeter in parallel and the voltmeter in series with the resistance

Last Answer : Answer: C

Suppose the ammeter or voltmeter you are using in the Ohm’s law experiment does not have +ve and –ve terminal markings. How will you use such ammeter or voltmeter in the circuit?

Description : Suppose the ammeter or voltmeter you are using in the Ohm’s law experiment does not have +ve and –ve terminal markings. How will you use such ammeter or voltmeter in the circuit?

Last Answer : Answer. We will use a typical battery to determine this. Connect them with wire and the battery if their readings are positive then we have connected them correctly and if their readings in negative then we have connected in opposite polarity.

Electric current is measured by (1) Voltmeter (2) Anemometer (3) Commutator (4) Ammeter

Description : Electric current is measured by (1) Voltmeter (2) Anemometer (3) Commutator (4) Ammeter

Last Answer : (4) Ammeter

Desirable resistance of a ________ is achieved by connecting a high resistance Rh in series with a galvanometer a) Ammeter b) Ohmmeter c) LED d) Voltmeter

Description : Desirable resistance of a ________ is achieved by connecting a high resistance Rh in series with a galvanometer a) Ammeter b) Ohmmeter c) LED d) Voltmeter

Last Answer : d) Voltmeter

Instrument used to find the source of seismic waves is known as a) seismometer b) voltmeter c) galvanometer d) ammeter

Description : Instrument used to find the source of seismic waves is known as a) seismometer b) voltmeter c) galvanometer d) ammeter

Last Answer : a) seismometer

State any four precautions to be taken while using an Ammeter and Voltmeter.

Description : State any four precautions to be taken while using an Ammeter and Voltmeter. 

Last Answer : Precautions to be taken while using Ammeters: Ammeters are to be connected in series of circuits. 1. While connecting ammeters across emf source always a series resistance should be used. This ... first &then range should be decreased. 4. Loading effect can be minimized by using high sensitivity

Which of the following instruments should never have their test leads connected directly to a wall outlet: w) ammeter x) voltmeter y) oscilloscope z) frequency counter

Description : Which of the following instruments should never have their test leads connected directly to a wall outlet: w) ammeter x) voltmeter y) oscilloscope z) frequency counter

Last Answer : ANSWER: W -- AMMETER

Electric current is measured using which of the following instrument ? (1) Ammeter (2) Voltmeter (3) Anemometer (4) Wattmeter

Description : Electric current is measured using which of the following instrument ? (1) Ammeter (2) Voltmeter (3) Anemometer (4) Wattmeter

Last Answer : Ammeter

Conversion of heat into electrical er is achieved by using : (1) Ammeter (2) Hydrometer (3) Voltmeter (4) Thermocouple

Description : Conversion of heat into electrical er is achieved by using : (1) Ammeter (2) Hydrometer (3) Voltmeter (4) Thermocouple

Last Answer : Thermocouple

Use Voltmeter, ammeter, wattmeter to determine active, reactive and apparent power consumed in given R—C series circuit, draw phasor diagram.

Description : Use Voltmeter, ammeter, wattmeter to determine active, reactive and apparent power consumed in given R—C series circuit, draw phasor diagram.

Last Answer : Use Voltmeter, ammeter, wattmeter to determine active, reactive and apparent power consumed in given R-C series circuit, draw phasor diagram. Practical Significance In the industry environment ... autotransformer position to zero and switch OFF the supply. 8. Draw the phasor diagram.

Use Voltmeter, ammeter, wattmeter to determine active, reactive and apparent power consumed in given R-L series circuit, draw phasor diagram.

Description : Use Voltmeter, ammeter, wattmeter to determine active, reactive and apparent power consumed in given R-L series circuit, draw phasor diagram.

Last Answer : Practical Significance In the industry environment Electrical Engineering diploma graduate are expected to measure basic parameters like voltage, frequency, time period etc. for R-L series circuits. Therefore ... /varying L. 7. Draw the phasor diagram for each of reading for verification.

Draw a typical electric circuit including ammeter and voltmeter.

Description : Draw a typical electric circuit including ammeter and voltmeter.

Last Answer : The figure shows typical electric circuit including ammeter and voltmeter. Ammeter is connected in series for measurement of current. Voltmeter is connected in parallel for measurement of voltage. Fuse is use ... are used. If the electric supply is DC the DC ammeter and DC voltmeter are used.

Which of the following will happen if a voltmeter is connected like an ammeter in series to the

Description : Which of the following will happen if a voltmeter is connected like an ammeter in series to the load ? (A) There will be almost no current in the circuit. (B) The meter will burn. (C) The measurement will be trio high. (D)  A very high current will flow.

Last Answer : Which of the following will happen if a voltmeter is connected like an ammeter in series to the load ? (A) There will be almost no current in the circuit. (B) The meter will burn. (C) The measurement will be trio high. (D)  A very high current will flow.

If a DC voltmeter is made from an ammeter having a fed of 100μA then its sensitivity (in KΩ/V) will be

Last Answer :  If a DC voltmeter is made from an ammeter having a fed of 100μA then its sensitivity (in KΩ/V) will be 10.

If a voltmeter is connected, like an ammeter in series to the load:

Last Answer : If a voltmeter is connected, like an ammeter in series to the load: Almost no current will flow in the circuit

What is meant by transformer ratio ?

Description : What is meant by transformer ratio ?

Last Answer : The relationship between the voltage, the number of punches and the current in the primary and secondary coils of a transformer is called the transformer ratio of the transformer. It can be ... Current Notice the image below. Hopefully it will be helpful to understand the transformation ratio.

What is meant by "integrated circuit" and "open circuit" ?

Description : What is meant by "integrated circuit" and "open circuit" ?

Last Answer : Answer : Integrated circuit refers to a complete electrical path through which electric current can flow through a horizontal electric field.

What is meant by digital electronics ?

Description : What is meant by digital electronics ?

Last Answer : A signal or symbol that has two defined layers , no unknown state, and whose layers change step by step over time and have specific steps , is called digital electronics.

What is meant by Logic Level of Digital Signal ?

Description : What is meant by Logic Level of Digital Signal ?

Last Answer : The voltage used to indicate binary '1' and '0' is called logic level.

What is meant by pulse rate or frequency of digital signal ?

Description : What is meant by pulse rate or frequency of digital signal ?

Last Answer : The number of vibrations per second in a signal is called Pulse rate .

What is meant by Digital Cycle Duty Cycle ?

Description : What is meant by Digital Cycle Duty Cycle ?

Last Answer : Duty Cycle = Vibration / Period X 100% . For example , if tw = T / 2 , Duty cycle = 50% .

What is meant by static properties ?

Description : What is meant by static properties ?

Last Answer : : When the voltages applied to different electrodes of the triode are insufficient or DC and no load resistance is included in the plate circuit and there is no signal at the input , it is called.

What is meant by constant current source ? What is a constant current source ?

Description : What is meant by constant current source ? What is a constant current source ?

Last Answer : A voltage source whose internal impedance is much higher than that of external load impedance is called a constant current source.