Explain Briefly What Happens When The Intr Signal Goes High In The 8085?

Explain Briefly What Happens When The Intr Signal Goes High In The 8085?
by

1 Answer

Answer :

Answer :The INTR is a maskable interrupt for the 8085. It has the lowest priority and is also non vectored. When this INTR signal goes into the high state the following things occur / take place:
For every instruction that is executed the 8085 checks the status of this interrupt./Till an instruction is completed the signal of INTR will remain high. Once an instruction is completed the processor sends an acknowledgement signal INTA. As soon as the INTA signal goes low a new opcode is placed on the data bus for transfer.
Once the new instruction is received the processor saves the address of new instruction into the STACK and an interrupt service subroutine begins.
by

Related questions

The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse

Description : The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse width of the INTR signal so that it is recognized successfully? A) 5.6 µs B) 5.7 µs C) 5.8 µs D) 5.9 µs

Last Answer : The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse width of the INTR signal so that it is recognized successfully? A) 5.6 µs B) 5.7 µs C) 5.8 µs D) 5.9 µs

In 8085, whenever a signal is received at TRAP terminal, its program execution is transferred to a subroutine

Description : In 8085, whenever a signal is received at TRAP terminal, its program execution is transferred to a subroutine on address A) 0000 H B) 002C H C) 0024 H D) 0004 H

Last Answer : In 8085, whenever a signal is received at TRAP terminal, its program execution is transferred to a subroutine on address 0024 H

What Are The Two Major Differences Between Intr And Other Interrupts ( Hardware)?

Description : What Are The Two Major Differences Between Intr And Other Interrupts ( Hardware)?

Last Answer : Answer :The two major differences between INTR and the other hardware interrupts are as follows:All the hardware interrupts are vectored interrupts but the INTR interrupt is not so. An INTR interrupt will ... saved but in the case of other hardware interrupts the locations is saved in the stack.

Explain Briefly The Flag Register In The 8085 Microprocessor.?

Description : Explain Briefly The Flag Register In The 8085 Microprocessor.?

Last Answer : Answer :The flag register in 8085 is an 8-bit register which contains 5 bit positions. These five flags are of 1bit F/F and are known as zero, sign, carry, parity and auxiliary carry. ... addition and subtraction operations. The parity flag is used for results containing an even number of one's.

Explain Briefly The Trap Input For The 8085.?

Description : Explain Briefly The Trap Input For The 8085.?

Last Answer : Answer :The TRAP input is sensitive to both edge and level. The pulse width for this signal should be in excess as compared to the normal noise width. A second trap will never be able to ... to low transition. The pulse widths are wider than normal widths so as to prevent unwanted false triggers.

Describe Briefly The Accumulator Register Of 8085.?

Description : Describe Briefly The Accumulator Register Of 8085.?

Last Answer : Answer :It is one of the most important 8 bit register of 8085 It is responsible for coordinating input and output to and from the microprocessor through it. The primary purpose of ... logical operations. This accumulator register is mainly used for arithmetic, logical, store and rotate operations.

In 8085 Which Is Called As High Order / Low Order Register?

Description : In 8085 Which Is Called As High Order / Low Order Register?

Last Answer : Answer :Flag is called as Low order register & Accumulator is called as High order Register.

Explain In Brief The Control And Timing Circuitry Of The 8085.?

Description : Explain In Brief The Control And Timing Circuitry Of The 8085.?

Last Answer : Answer :The timing and control circuitry section of the 8085 is responsible for the generation of timing and control signals so that instructions can be executed. The types of signals involved ... of control signals for the executions of instructions and for the sync between external devices.

Explain All The Addressing Modes Of The 8085 With The Help Of Examples.?

Description : Explain All The Addressing Modes Of The 8085 With The Help Of Examples.?

Last Answer : Answer :The various types of addressing modes of the 8085 are as follows: Direct addressing: The instructions in itself contain the opearand. For ex. STA5513H or in/out instructions such as IN PORT C. ... etc. Implicit addressing: this form of addressing contains no operands. For ex. RAR, CMA etc.

Does The 8085 Support Externally Initiated Operations? If Yes How?

Description : Does The 8085 Support Externally Initiated Operations? If Yes How?

Last Answer : Answer :Yes the 8085 does support several externally initiated operations. The possible operations and the corresponding pins for them in the 8085 are as follows: It supports resetting ( this is possible ... It also has a HOLD pin which can basically pause the operation till required/ as required.

Mention The Different Types Of Data Transfers Possible In The 8085.?

Description : Mention The Different Types Of Data Transfers Possible In The 8085.?

Last Answer : Answer :The various types of data transfer operations possible are: Data transfer is possible between two registers. It is also possible between a memory location and a register. Also it can occur between ... . In reality data is never transferred it can only be copied from one location to another.

Mention The Various Functional Blocks Of The 8085 Microprocessor.?

Description : Mention The Various Functional Blocks Of The 8085 Microprocessor.?

Last Answer : Answer :The various functional blocks of the 8085 microprocessor are: Registers Arithmetic logic unit Address buffer Increment / decrement address latch Interrupt control Serial I/O control Timing and control circuitry Instructions decoder and machine cycle encoder.

How Can Signals Be Classified For The 8085 Microprocessor?

Description : How Can Signals Be Classified For The 8085 Microprocessor?

Last Answer : Answer :The signals of the 8085 microprocessor based on their functions can be classified into 7 categories namely: Frequency and power signals Address and data buses The control bus Interrupt Signals Serial Input / Output signals DMA signals Reset Signals

Can An Rc Circuit Be Used As Clock Source For 8085?

Description : Can An Rc Circuit Be Used As Clock Source For 8085?

Last Answer : Answer :Yes, it can be used, if an accurate clock frequency is not required. Also, the component cost is low compared to LC or Crystal.

How Many Interrupts Are There In 8085?

Description : How Many Interrupts Are There In 8085?

Last Answer : Answer :There are 12 interrupts in 8085.

In What Way Interrupts Are Classified In 8085?

Description : In What Way Interrupts Are Classified In 8085?

Last Answer : Answer :In 8085 the interrupts are classified as Hardware and Software interrupts.

Which Stack Is Used In 8085?

Description : Which Stack Is Used In 8085?

Last Answer : Answer :LIFO (Last In First Out) stack is used in 8085.In this type of Stack the last stored information can be retrieved first.

What Are The Various Flags Used In 8085?

Description : What Are The Various Flags Used In 8085?

Last Answer : Answer :Sign flag, Zero flag, Auxillary flag, Parity flag, Carry flag.

What Are The Various Registers In 8085?

Description : What Are The Various Registers In 8085?

Last Answer : Answer :Accumulator register, Temporary register, Instruction register, Stack Pointer, Program Counter are the various registers in 8085.

List any four salient features of 8085 microprocessor

Description : List any four salient features of 8085 microprocessor

Last Answer : Features of 8085:  1. 16 address line so 216=64 Kbytes of memory can be addressed.  2. Operating clock frequency is 3MHz and minimum clock frequency is 500 KHz.  3. On chip bus controller ... duty cycle TTL clock  10. Provide 2 serial I/O lines, so peripheral can be interfaced with 8085 μp

The 8085 Microprocessor has

Description : The 8085 Microprocessor has A) 8-bits Data bus and 16-bits Address bus B) 8-bits Data bus and 8-bits Address bus C) 16-bits Data bus and 16-bits Address bus D) 32-bits Data bus and 8-bits Address bus 

Last Answer : B) 8-bits Data bus and 8-bits Address bus. 

In 8085 microprocessor, how many T-states does OPCODE FETCH machine cycle normally require

Description : In 8085 microprocessor, how many T-states does OPCODE FETCH machine cycle normally require (i.e., when HOLD and WAIT signals are NOT forced)? A) 4 to 6 B) 3 to 8 C) 2 to 3 D) 8 to 12 

Last Answer : In 8085 microprocessor, how many T-states does OPCODE FETCH machine cycle normally require (i.e., when HOLD and WAIT signals are NOT forced)? A) 4 to 6 B) 3 to 8 C) 2 to 3 D) 8 to 12 

Then number of T-states of the instruction STA in 8085 microprocessor is

Description : Then number of T-states of the instruction STA in 8085 microprocessor is A) 10 B) 12 C) 13 D) 16 

Last Answer : Then number of T-states of the instruction STA in 8085 microprocessor is 13 

What is the size of memory which can be accessed by direct accessing in 8085 microprocessor?

Description : What is the size of memory which can be accessed by direct accessing in 8085 microprocessor? A) 64 kB B) 4 kB C) 128 kB D) 128 MB 

Last Answer : What is the size of memory which can be accessed by direct accessing in 8085 microprocessor? A) 64 kB B) 4 kB C) 128 kB D) 128 MB 

What is the size of SP register in 8085 microprocessor?

Description :  What is the size of SP register in 8085 microprocessor? A) 16 bits B) 8 bits C) 64 bits D) 48 bits

Last Answer :  What is the size of SP register in 8085 microprocessor? A) 16 bits B) 8 bits C) 64 bits D) 48 bits

The ALE line of an 8085 microprocessor is used to

Description : The ALE line of an 8085 microprocessor is used to (A) latch the output of an I/O instruction into an external latch. (B) deactivate the chip-select signal from memory devices. (C) find the interrupt ... of the TRAP interrupt. (D) latch the 8 bits of address lines AD7-AD0 into an external latch.

Last Answer : The ALE line of an 8085 microprocessor is used to latch the 8 bits of address lines AD7-AD0 into an external latch.

What is the significance of signal conditioner? Explain the need of following in mechatronics system. i) Isolator ii) Filter iii) Amplifier iv) Data converter

Description : What is the significance of signal conditioner? Explain the need of following in mechatronics system. i) Isolator ii) Filter iii) Amplifier iv) Data converter

Last Answer : Significance: Signal conditioning means manipulating an analog signal in such a way that it meets the requirements of the next stage for further processing. Signal inputs accepted by signal ... -frequency converters, current-to-voltage converters, current loop converters, and charge converters.  

For a signal conditioner explain the terms linearization and signal conversion.

Description : For a signal conditioner explain the terms linearization and signal conversion.

Last Answer : Definition :  1. linearization : Many primary elements produce nonlinear outputs and the signal must be linearized to produce a nearly ideal calibration. Specialized analog circuits such as offsetting circuits, ... signal. Even computer algorithms are also used. 2.Signal conversion :

2.The period of a signal is 10ms. What is its frequency in kilohertz?

Description : .2.The period of a signal is 10ms. What is its frequency in kilohertz?

Last Answer : 100

State different types of electrical signal and draw all types of waveforms.

Description : State different types of electrical signal and draw all types of waveforms.

Last Answer : Types of electrical signals 1) Sine wave 2) Triangular wave 3) Square wave Waveforms

basic characteristics of sound signal.

Description :  basic characteristics of sound signal.

Last Answer : Level and loudness: The amplitude of a sound wave determines its loudness or volume. A larger amplitude means a louder sound, and a smaller amplitude means a softer sound. The loudness of a ... the reproducing system should be capable of handling the maximum and minimum power in the same ratio. 

List different methods of demodulation of FM signal.

Description : List different methods of demodulation of FM signal.

Last Answer : Balanced Slope detection Ratio detector Foster Seeley discriminator Phase locked loop demodulator 

Analog signal

Description : Analog signal

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

If it takes a transmitted signal 1m sec to go up to the target and come back after reflection, how far is

Description :  If it takes a transmitted signal 1m sec to go up to the target and come back after reflection, how far is the transmitter from the target? A) 150 Km B) 150 m C) 15 Km D) 1500 m 

Last Answer :  If it takes a transmitted signal 1m sec to go up to the target and come back after reflection, how far is the transmitter from the target? A) 150 Km B) 150 m C) 15 Km D) 1500 m 

If a signal band limited to fm is sampled at a rate less than 2fm, then the constructed signal will be

Description :  If a signal band limited to fm is sampled at a rate less than 2fm, then the constructed signal will be A) Large in amplitude B) Small in amplitude C) Distorted D) Distortion less

Last Answer :  If a signal band limited to fm is sampled at a rate less than 2fm, then the constructed signal will be Distorted 

An energy signal has G(f) = 20. Its energy density spectrum is

Description :  An energy signal has G(f) = 20. Its energy density spectrum is A) 20 B) 100 C) 400 D) 800  

Last Answer : 400

What is the Laplace transform of step signal of 5 units magnitude?

Description : What is the Laplace transform of step signal of 5 units magnitude?  A) 5s B) 5/s C) s/5 D) 1/s 

Last Answer : What is the Laplace transform of step signal of 5 units magnitude?  A) 5s B) 5/s C) s/5 D) 1/s 

The time base signal in Cathode Ray Oscilloscope (CRO) is

Description : The time base signal in Cathode Ray Oscilloscope (CRO) is  (1) A square wave signal (2) A sawtooth signal (3) A triangular wave signal (4) A sinusoidal signal

Last Answer : 2 Saw tooth 

Integration of step signal gives

Description : Integration of step signal gives (A) Impulse signal. (B) Ramp function. (C) Parabola. (D) Square pulse.

Last Answer : Integration of step signal gives Ramp function.

The standard for long distance analog signal transmission in process control industry is

Description : The standard for long distance analog signal transmission in process control industry is (A) 4-20 mV (B) 0-20 mA (C) 4-20 mA (D) 0-5 V

Last Answer : The standard for long distance analog signal transmission in process control industry is 4-20 mA

What are the advantages of a digital signal?

Description : What are the advantages of a digital signal?

Last Answer : It  has   only   two  variable   input  and  output (low   or    high)   (0  or    5).

Which of the following 8085 microprocessor hardware interrupt has the lowest priority? (A) RST 6.5 (B) RST 7.5 (C) TRAP (D) INTR

Description : Which of the following 8085 microprocessor hardware interrupt has the lowest priority? (A) RST 6.5 (B) RST 7.5 (C) TRAP (D) INTR 

Last Answer : Answer: D

In 8086, Example for Non maskable interrupts are a) Trapb) RST6.5 c) INTR

Description : In 8086, Example for Non maskable interrupts are a) Trapb) RST6.5 c) INTR

Last Answer : a) Trap

What are software interrupts? a) RST 0 - 7 b) RST 5.5 - 7.5 c) INTR, TRAP

Description : What are software interrupts? a) RST 0 - 7 b) RST 5.5 - 7.5 c) INTR, TRAP

Last Answer : a) RST 0

Which of the following is hardware interrupts? a) RST5.5, RST6.5, RST7.5 b) INTR, TRAP c) a & b

Description : Which of the following is hardware interrupts? a) RST5.5, RST6.5, RST7.5 b) INTR, TRAP c) a & b

Last Answer : c) a & b

Which interrupt has the highest priority? a) INTR b) TRAP c) RST6.5

Description : Which interrupt has the highest priority? a) INTR b) TRAP c) RST6.5

Last Answer : c) RST6.5

If you are to use [Control-c] as the interrupt key instead of [Del], then you will have to use A. tty ^c B. stty intr \^c C. stty echoe D. stty echo \^a E. None of the above

Description : If you are to use [Control-c] as the interrupt key instead of [Del], then you will have to use A. tty ^c B. stty intr \^c C. stty echoe D. stty echo \^a E. None of the above

Last Answer : B. stty intr \^c

What is the signal classification of 8085

Description : What is the signal classification of 8085

Last Answer : All the signals of 8085 can be classified into 6 groups • Address bus • Data bus • Control and status signals • Power supply and frequency signals • Externally initiated signals • Serial I/O ports

What is the function of IO/M signal in the 8085?

Description : What is the function of IO/M signal in the 8085?

Last Answer : It is a status signal. It is used to differentiate between memory locations and I/O operations. When this signal is low (IO/M = 0) it denotes the memory related operations. When this signal is high (IO/M = 1) it denotes an I/O operation.

Which signal of 8085 microprocessor is used to insert wait states ?

Description : Which signal of 8085 microprocessor is used to insert wait states ?   (a) Ready (b) ALE (c) HOLD (d) INTR

Last Answer : Which signal of 8085 microprocessor is used to insert wait states ?   (a) Ready (b) ALE (c) HOLD (d) INTR