The speed of conversion is maximum in (A) Successive-approximation A/D converter. (B) Parallel-comparative A/D converter. (C) Counter ramp A/D converter. (D) Dual-slope A/D converter.

The speed of conversion is maximum in
(A) Successive-approximation A/D converter.
(B) Parallel-comparative A/D converter.
(C) Counter ramp A/D converter.
(D) Dual-slope A/D converter.
by

1 Answer

Answer :

Ans: B
The speed of conversion is maximum in Parallel-comparator A/D converter
(Speed of conversion is maximum because the comparisons of the input voltage are
carried out simultaneously.)
by

Related questions

The A/D converter whose conversion time is independent of the number of bits is (A) Dual slope (B) Counter type (C) Parallel conversion (D) Successive approximation.

Description : The A/D converter whose conversion time is independent of the number of bits is (A) Dual slope (B) Counter type (C) Parallel conversion (D) Successive approximation.

Last Answer : Ans: C The A/D converter whose conversion time is independent of the Number of bits is Parallel conversion. (This type uses an array of comparators connected in parallel and comparators compare the input voltage at a particular ratio of the reference voltage).

The conversation speed of an analog to digital converter is maximum with the following technique. (A) Dual slope AD converter. (B) Serial comparator AD converter. (C) Successive approximation AD converter. (D) Parallel comparator AD converter.

Description : The conversation speed of an analog to digital converter is maximum with the following technique. (A) Dual slope AD converter. (B) Serial comparator AD converter. (C) Successive approximation AD converter. (D) Parallel comparator AD converter.

Last Answer : (D) Parallel comparator AD converter.

In successive-approximation A/D converter, offset voltage equal to 1/2 LSB is added to the D/A converter’s output. This is done to (A) Improve the speed of operation. (B) Reduce the maximum quantization error. (C) Increase the number of bits at the output. (D) Increase the range of input voltage that can be converted

Description : In successive-approximation A/D converter, offset voltage equal to 1/2 LSB is added to the D/A converter's output. This is done to (A) Improve the speed of operation. (B) Reduce the maximum ... Increase the number of bits at the output. (D) Increase the range of input voltage that can be converted

Last Answer : (B) Reduce the maximum quantization error.

The conversion time of a 12 bit successive approximation A/D converter using a 1 MHz clock is

Last Answer : The conversion time of a 12 bit successive approximation A/D converter using a 1 MHz clock is 12μs.

For a certain 4 bit successive approximation A/D converter, the maximum ...

Last Answer : For a certain 4 bit successive approximation A/D converter, the maximum ladder output is +8V. if a constant +6V is applied to the analog input the sequence of binary states for the SA register is 0110.

In successive approximation converter input to the comparator is through

Description : In successive approximation converter input to the comparator is through (A) DAC (B) Latch (C) Flip-flop (D) Sample and hold circuit

Last Answer : In successive approximation converter input to the comparator is through DAC 

The device which changes from serial data to parallel data is (A) COUNTER (B) MULTIPLEXER (C) DEMULTIPLEXER (D) FLIP-FLOP

Description : The device which changes from serial data to parallel data is (A) COUNTER (B) MULTIPLEXER (C) DEMULTIPLEXER (D) FLIP-FLOP

Last Answer : Ans: C The device which changes from serial data to parallel data is demultiplexer. (A demultiplexer takes in data from one line and directs it to any of its N outputs depending on the status of the select inputs.)

The code where all successive numbers differ from their preceding number by single bit is (A) Binary code. (B) BCD. (C) Excess – 3. (D) Gray.

Description : The code where all successive numbers differ from their preceding number by single bit is (A) Binary code. (B) BCD. (C) Excess – 3. (D) Gray.

Last Answer : Ans: D The code where all successive numbers differ from their preceding number by single bit is Gray Code. (It is an unweighted code. The most important characteristic of this code is that only a single bit change occurs when going from one code number to next.)

A 4-bit synchronous counter uses flip-flops with propagation delay times of 15 ns each. The maximum possible time required for change of state will be (A) 15 ns. (B) 30 ns. (C) 45 ns. (D) 60 ns.

Description : A 4-bit synchronous counter uses flip-flops with propagation delay times of 15 ns each. The maximum possible time required for change of state will be (A) 15 ns. (B) 30 ns. (C) 45 ns. (D) 60 ns.

Last Answer : Ans: A 15 ns because in synchronous counter all the flip-flops change state at the same time.

The MSI chip 7474 is (A) Dual edge triggered JK flip-flop (TTL). (B) Dual edge triggered D flip-flop (CMOS). (C) Dual edge triggered D flip-flop (TTL). (D) Dual edge triggered JK flip-flop (CMOS).

Description : The MSI chip 7474 is (A) Dual edge triggered JK flip-flop (TTL). (B) Dual edge triggered D flip-flop (CMOS). (C) Dual edge triggered D flip-flop (TTL). (D) Dual edge triggered JK flip-flop (CMOS).

Last Answer : Ans: C MSI chip 7474 dual edge triggered D Flip-Flop.

A weighted resistor digital to analog converter using N bits requires a total of (A) N precision resistors. (B) 2N precision resistors. (C) N + 1 precision resistors. (D) N – 1 precision resistors.

Description : A weighted resistor digital to analog converter using N bits requires a total of (A) N precision resistors. (B) 2N precision resistors. (C) N + 1 precision resistors. (D) N – 1 precision resistors.

Last Answer : (A) N precision resistors.

A 12 bit counter type A/D converter uses a 1 MHz clock. Its maximum conversion time is

Last Answer : A 12 bit counter type A/D converter uses a 1 MHz clock. Its maximum conversion time is 4096μs.

An eight stage ripple counter uses a flip-flop with propagation delay of 75 nanoseconds. The pulse width of the strobe is 50ns. The frequency of the input signal which can be used for proper operation of the counter is approximately (A) 1 MHz. (B) 500 MHz. (C) 2 MHz. (D) 4 MHz.

Description : An eight stage ripple counter uses a flip-flop with propagation delay of 75 nanoseconds. The pulse width of the strobe is 50ns. The frequency of the input signal which can be used for proper operation of the counter is approximately (A) 1 MHz. (B) 500 MHz. (C) 2 MHz. (D) 4 MHz.

Last Answer : Maximum time taken for all flip-flops to stabilize is 75ns x 8 + 50 = 650ns. Frequency of operation must be less than 1/650ns = 1.5 MHz.

How many flip-flops are required to construct mod 30 counter (A) 5 (B) 6 (C) 4 (D) 8

Description : How many flip-flops are required to construct mod 30 counter (A) 5 (B) 6 (C) 4 (D) 8

Last Answer : (A) 5

How many flip flops are required to construct a decade counter (A) 10 (B) 3 (C) 4 (D) 2

Description : How many flip flops are required to construct a decade counter (A) 10 (B) 3 (C) 4 (D) 2

Last Answer : Ans: C Decade counter counts 10 states from 0 to 9 ( i.e. from 0000 to 1001 ) Thus four FlipFlop's are required.

A ring counter consisting of five Flip-Flops will have (A) 5 states (B) 10 states (C) 32 states (D) Infinite states.

Description : A ring counter consisting of five Flip-Flops will have (A) 5 states (B) 10 states (C) 32 states (D) Infinite states.

Last Answer : Ans: A A ring counter consisting of Five Flip-Flops will have 5 states.

How many Flip-Flops are required for mod–16 counter? (A) 5 (B) 6 (C) 3 (D) 4

Description : How many Flip-Flops are required for mod–16 counter? (A) 5 (B) 6 (C) 3 (D) 4

Last Answer : (D) 4

Where can I find the detailed information about Successive Approximation method and discrete newton method？?

Description : Where can I find the detailed information about Successive Approximation method and discrete newton method？?

Last Answer : answer:A DISCRETE NEWTON ALGORITHM FOR MINIMIZING A FUNCTION OF MANY VARIABLES SUCCESSIVE APPROXIMATIONS

Where are the successive approximation type ADC’s used?

Description : Where are the successive approximation type ADC’s used?

Last Answer : The Successive approximation ADCs are used in applications such as data loggers & instrumentation where conversion speed is important.

Explain in brief the principle of operation of successive Approximation ADC.

Description : Explain in brief the principle of operation of successive Approximation ADC.

Last Answer : The circuit of successive approximation ADC consists of a successive approximation register (SAR), to find the required value of each bit by trial & error.With the arrival of START command, SAR sets the MSB ... /P signal. This O/P is low or High. This process continues until all bits are checked.

Draw block diagram of successive approximation digital voltmeter. State its two advantages and two disadvantages

Description : Draw block diagram of successive approximation digital voltmeter. State its two advantages and two disadvantages

Last Answer : Block diagram Or Advantages: o It is economical method of analog to digital conversion. o The resolution is up to 5 important digits are obtained. Disadvantages: o ... depends on which type of switches are used. o The conversion time required for digital to analog converter.

Successive approximation technique is used for

Description : Successive approximation technique is used for

Last Answer : Successive approximation technique is used for A to D Conversion

Is it more difficult to run up a ramp with a slope of 15 or a ramp with a slope of 5 Explain.?

Description : Is it more difficult to run up a ramp with a slope of 15 or a ramp with a slope of 5 Explain.?

Last Answer : The answer depends on what causes the difficulty: the steepnessor the distance which you have to run.

Contour interval on a map sheet denotes (a) Vertical distance of contour lines above the datum plane (b) Vertical distance between two successive contour lines (c) Slope distance between two successive contour lines (d) Horizontal distance between two successive contour lines

Description : Contour interval on a map sheet denotes (a) Vertical distance of contour lines above the datum plane (b) Vertical distance between two successive contour lines (c) Slope distance between two successive contour lines (d) Horizontal distance between two successive contour lines

Last Answer : (b) Vertical distance between two successive contour lines

Define Asynchronous sequential circuit?

Description : Define Asynchronous sequential circuit?

Last Answer : In asynchronous sequential circuits change in input signals can affect memory element at any instant of time.

Define synchronous sequential circuit

Description : Define synchronous sequential circuit

Last Answer : In synchronous sequential circuits, signals can affect the memory elements only at discrete instant of time.

What are the different types of shift type?

Description : What are the different types of shift type?

Last Answer : There are five types. They are, Serial In Serial Out Shift Register Serial In Parallel Out Shift Register Parallel In Serial Out Shift Register Parallel In Parallel Out Shift Register Bidirectional Shift Register

Define shift registers.

Description : Define shift registers.

Last Answer : The binary information in a register can be moved from stage to stage within the register or into or out of the register upon application of clock ... arithmetic and logic operations used in microprocessors. This gives rise to group of registers called shift registers.

Define registers.

Description : Define registers.

Last Answer : A register is a group of flip-flops flip-flop can store one bit information. So an n-bit register has a group of n flip-flops and is capable of storing any binary information/number containing n-bits.

What is a master-slave flip-flop?

Description : What is a master-slave flip-flop?

Last Answer : A master-slave flip-flop consists of two flip-flops where one circuit serves as a master and the other as a slave.

What is edge-triggered flip-flop?

Description : What is edge-triggered flip-flop?

Last Answer : The problem of race around condition can solved by edge triggering flip flop. The term edge triggering means that the flip-flop changes state either at the positive ... negative edge of the clock pulse and it is sensitive to its inputs only at this transition of the clock.

Define race around condition.

Description : Define race around condition.

Last Answer : In JK flip-flop output is fed back to the input. Therefore change in the output results change in the input. Due to this in the positive half of the clock pulse if both J and K are high then output toggles continuously. This condition iscalled ‘race around condition’.

What is the operation of T flip-flop?

Description : What is the operation of T flip-flop?

Last Answer : T flip-flop is also known as Toggle flip-flop. • When T=0 there is no change in the output. • When T=1 the output switch to the complement state (ie) the output toggles.

What is the operation of JK flip-flop?

Description : What is the operation of JK flip-flop?

Last Answer : When K input is low and J input is high the Q output of flip-flop is set. When K input is high and J input is low the Q output of flip-flop is reset. When both the inputs ... are high it is possible to set or reset the flip-flop (ie) the output toggle on the next positive clock edge.

What is the operation of D flip-flop?

Description : What is the operation of D flip-flop?

Last Answer : In D flip-flop during the occurrence of clock pulse if D=1, the output Q is set and if D=0, the output is reset.

What are the different types of flip-flop?

Description : What are the different types of flip-flop?

Last Answer : There are various types of flip flops. Some of them are mentioned below they are, RS flip-flop SR flip-flop D flip-flop JK flip-flop T flip-flop

Define Flip flop.

Description : Define Flip flop.

Last Answer : The basic unit for storage is flip flop. A flip-flop maintains its output state either at 1 or 0 until directed by an input signal to change its state.

What are the classification of sequential circuits?

Description : What are the classification of sequential circuits?

Last Answer : The sequential circuits are classified on the basis of timing of their signals into two types. They are, 1)Synchronous sequential circuit. 2)Asynchronous sequential circuit.

What do you mean by comparator

Description : What do you mean by comparator

Last Answer : A comparator is a special combinational circuit designed primarily to compare the relative magnitude of two binary numbers.

Define multiplexer

Description : Define multiplexer

Last Answer : Multiplexer is a digital switch. If allows digital information from several sources to be routed onto a single output line.

What is priority Encoder?

Description : What is priority Encoder?

Last Answer : A priority encoder is an encoder circuit that includes the priority function. In priority encoder, if 2 or more inputs are equal to 1 at the same time, the input having the highest priority will take precedence.

Define Encoder?

Description : Define Encoder?

Last Answer : An encoder has 2n input lines and n output lines. In encoder the output lines generate the binary code corresponding to the input value.

What is binary decoder?

Description : What is binary decoder?

Last Answer : A decoder is a combinational circuit that converts binary information from n input lines to a maximum of 2n out puts lines.

Define Decoder

Description : Define Decoder

Last Answer : A decoder is a multiple - input multiple output logic circuit that converts coded inputs into coded outputs where the input and output codes are different.

Define Half adder and full adder

Description : Define Half adder and full adder

Last Answer : The logic circuit that performs the addition of two bits is a half adder. The circuit that performs the addition of three bits is a full adder.

Define combinational logic

Description : Define combinational logic

Last Answer : When logic gates are connected together to produce a specified output for certain specified combinations of input variables, with no storage involved, the resulting circuit is called combinational logic.

Convert the decimal number 3.375 to binary. 132) A) 0101.1100 B) 0011.1010 C) 0011.0011 D) 0011.01

Description : Convert the decimal number 3.375 to binary. 132) A) 0101.1100 B) 0011.1010 C) 0011.0011 D) 0011.01

Last Answer : D) 0011.01

Convert binary 1001 to octal. 131) A) 1018 B) 98 C) 108 D) 118

Description : Convert binary 1001 to octal. 131) A) 1018 B) 98 C) 108 D) 118

Last Answer : D) 118

Convert decimal 19 to octal. 130) A) 278 B) 218 C) 238 D) 178

Description : Convert decimal 19 to octal. 130) A) 278 B) 218 C) 238 D) 178

Last Answer : C) 238

The hexadecimal equivalent of decimal 88 is ________. 129) A) 6816 B) 5816 C) 5116 D) 551

Description : The hexadecimal equivalent of decimal 88 is ________. 129) A) 6816 B) 5816 C) 5116 D) 551

Last Answer : B) 5816