A dc shunt generator has a speed of 800 rpm when delivering 20 A to the load at the terminal voltage of 220V. If the same machine is run as a motor it takes a line current of 20A from 220V supply. The speed of the machine as a motor will be (A) 800 rpm. (B) more than 800 rpm. (C) less than 800 rpm. (D) both higher or lower than 800 rpm.

A dc shunt generator has a speed of 800 rpm when delivering 20 A to the load at the
terminal voltage of 220V. If the same machine is run as a motor it takes a line
current of 20A from 220V supply. The speed of the machine as a motor will be
(A) 800 rpm. (B) more than 800 rpm.
(C) less than 800 rpm. (D) both higher or lower than 800 rpm.
by

1 Answer

Answer :

(C) less than 800 rpm.
by

Related questions

The simplest method of controlling the terminal voltage of compound-wound DC generator is with a _____________. A. hand-operated field rheostat connected in series with the shunt field circuit B. separate exciter in a series with the shunt field C. carbon pile regulator in series with the load D. balance coil diverting neutral current through the shunt field

Description : The simplest method of controlling the terminal voltage of compound-wound DC generator is with a _____________. A. hand-operated field rheostat connected in series with the shunt field circuit B. ... in series with the load D. balance coil diverting neutral current through the shunt field

Last Answer : Answer: A

When 220V dc shunt alternator generating the voltage at rated value. If direction of rotation is reversed, then alternator will a) Build up its voltage with same polarity b) Build up its voltage with opposite polarity c) No build up of voltage d) None

Description : When 220V dc shunt alternator generating the voltage at rated value. If direction of rotation is reversed, then alternator will a) Build up its voltage with same polarity b) Build up its voltage with opposite polarity c) No build up of voltage d) None

Last Answer : Ans: No build up of voltage

Which of the terms listed best describes a compound-wound DC generator having a higher voltage at no load than at full load? A. Flat compounded B. Over compounded C. Under compounded D. Terminal compounded

Description : Which of the terms listed best describes a compound-wound DC generator having a higher voltage at no load than at full load? A. Flat compounded B. Over compounded C. Under compounded D. Terminal compounded

Last Answer : Answer: C

An open shunt field in a direct current machine may be located by connecting the field circuit to an external power source, equal to the rated field voltage or less, and tested with a voltmeter from _____________. A. one line terminal to each coil lead in succession B. one field coil to each adjacent field coil in turn C. any suitable ground to any available line lead D. any field pole to each field coil lead

Description : An open shunt field in a direct current machine may be located by connecting the field circuit to an external power source, equal to the rated field voltage or less, and tested with a voltmeter from ... C. any suitable ground to any available line lead D. any field pole to each field coil lead

Last Answer : Answer: A

The terminal voltage of a DC shunt generator drops on load because of all of the following

Description : The terminal voltage of a DC shunt generator drops on load because of all of the following except : (A) Armature reaction (B) Armature resistance drop (C) Commutation (D) Field weakening due to armature reaction and armature resistance drop

Last Answer : (D) Field weakening due to armature reaction and armature resistance drop

A 4 pole lap wound dc shunt motor rotates at the speed of 1500 rpm, has a flux of 0.4 mWb and the total number of conductors are 1000. What is the value of emf? (A) 100 Volts. (B) 0.1 Volts. (C) 1 Volts. (D) 10 Volts.

Description : A 4 pole lap wound dc shunt motor rotates at the speed of 1500 rpm, has a flux of 0.4 mWb and the total number of conductors are 1000. What is the value of emf? (A) 100 Volts. (B) 0.1 Volts. (C) 1 Volts. (D) 10 Volts.

Last Answer : Ans: D Given N = 1500 rpm, Φ = 0.4 mWb, Z = 1000, P = 4, & A= 4 Therefore, Eb = NΦPZ / 60 A = 1500 x 0.4 x 4 x 1000 x 10^-3 / 60 x 4 = 60/6 = 10 volts

One method of testing for a reversed shunt field coil in a DC generator or motor is by connecting the field to a direct current source, at reduced field rated voltage, and test for polarity using a/an ____________. A. iron bar across each field B. magnetic compass placed near each field C. test lamp across adjacent fields D. copper jumper across the interpole connections

Description : One method of testing for a reversed shunt field coil in a DC generator or motor is by connecting the field to a direct current source, at reduced field rated voltage, and test for ... placed near each field C. test lamp across adjacent fields D. copper jumper across the interpole connections

Last Answer : Answer: B

A 220 V dc machine has an armature resistance o f 1-ohm. If the full load current is 20A, the difference...

Description : A 220 V dc machine has an armature resistance o f 1-ohm. If the full load current is 20A, the difference in the induced voltage when the machine is running as a motor, and as a generator is

Last Answer : A 220 V dc machine has an armature resistance o f 1-ohm. If the full load current is 20A, the difference in the induced voltage when the machine is running as a motor, and as a generator is 40 V.

A DC shunt motor has rated rpm of 480. Certain industrial application requires this motor to run at 540 rpm

Description : A DC shunt motor has rated rpm of 480. Certain industrial application requires this motor to run at 540 rpm for some time. Which speed control will be desirable? A) Ward Leonard control B) Armature ... ) Field resistance control D) It is not possible to run the motor at more than the rated rpm 

Last Answer : A DC shunt motor has rated rpm of 480. Certain industrial application requires this motor to run at 540 rpm for some time. Which speed control will be desirable? A) Ward Leonard control B) Armature ... Field resistance control D) It is not possible to run the motor at more than the rated rpm 

A 200 V dc shunt motor is running at 1000 rpm and drawing a current of 10 A. Its armature winding resistance

Description : A 200 V dc shunt motor is running at 1000 rpm and drawing a current of 10 A. Its armature winding resistance is 2 Ohm. It. is braked by plugging. The resistance to be connected in series with armature to restrict armature current to 10 A, is

Last Answer : A 200 V dc shunt motor is running at 1000 rpm and drawing a current of 10 A. Its armature winding resistance is 2 Ohm. It. is braked by plugging. The resistance to be connected in series with armature to restrict armature current to 10 A, is 36 Ohm

The no load speed of a d.c. shunt motor is 1140 rpm. At full load, the armature reaction weakens the main...

Description : The no load speed of a d.c. shunt motor is 1140 rpm. At full load, the armature reaction weakens the main flux by 5% whereas the armature circuit voltage drops by 10%. The motor full load speed in rpm will be: (A) 1080 (B) 1203 (C) 1000 (D) 1200

Last Answer : The no load speed of a d.c. shunt motor is 1140 rpm. At full load, the armature reaction weakens the main flux by 5% whereas the armature circuit voltage drops by 10%. The motor full load speed in rpm will be: 1080

A four pole turbogenerator is used in conjunction with a 160 pole propulsion motor. If the generator is turning at 3,200 RPM, what is the current speed of the propeller? A. 40 RPM B. 60 RPM C. 80 RPM D. 100 RPM

Description : A four pole turbogenerator is used in conjunction with a 160 pole propulsion motor. If the generator is turning at 3,200 RPM, what is the current speed of the propeller? A. 40 RPM B. 60 RPM C. 80 RPM D. 100 RPM

Last Answer : Answer: C

The most common source of excitation for synchronous motors is a/an _____________. A. low voltage battery B. motor attenuator set C. DC exciter generator D. AC supply

Description : The most common source of excitation for synchronous motors is a/an _____________. A. low voltage battery B. motor attenuator set C. DC exciter generator D. AC supply

Last Answer : Answer: C

As compared to shunt and compound DC motors, the series DC motor will have the highest torque because of its comparatively ____________ at the start. (A) Lower armature resistance. (B) Stronger series field. (C) Fewer series turns. (D) Larger armature current.

Description : As compared to shunt and compound DC motors, the series DC motor will have the highest torque because of its comparatively ____________ at the start. (A) Lower armature resistance. (B) Stronger series field. (C) Fewer series turns. (D) Larger armature current.

Last Answer : (D) Larger armature current.

A 220/440 V, 50 Hz, 5 KVA, single phase transformer operates on 220V, 40Hz supply with secondary winding open circuited. Then (A) Both eddy current and hysteresis losses decreases. (B) Both eddy current and hysteresis losses increases. (C) Eddy current loss remains the same but hysteresis loss increases. (D) Eddy current loss increases but hysteresis loss remains the same.

Description : A 220/440 V, 50 Hz, 5 KVA, single phase transformer operates on 220V, 40Hz supply with secondary winding open circuited. Then (A) Both eddy current and hysteresis losses decreases. (B) Both ... same but hysteresis loss increases. (D) Eddy current loss increases but hysteresis loss remains the same.

Last Answer : (A) Both eddy current and hysteresis losses decreases.

When using a megohmmeter to determine which shunt field coil is grounded in a DC machine, you must ____________. A. insulate the field frame from the ship's hull B. disconnect each shunt field coil before testing C. use a motor driven high capacity megohmmeter D. remove all main line lead connections before testing

Description : When using a megohmmeter to determine which shunt field coil is grounded in a DC machine, you must ____________. A. insulate the field frame from the ship's hull B. disconnect each shunt ... C. use a motor driven high capacity megohmmeter D. remove all main line lead connections before testing

Last Answer : Answer: B

The speed of a d.c. shunt motor at no-load is (A) 5 to 10% (B) 15 to 20% (C) 25 to 30% (D) 35 to 40% higher than its speed at rated load.

Description : The speed of a d.c. shunt motor at no-load is (A) 5 to 10% (B) 15 to 20% (C) 25 to 30% (D) 35 to 40% higher than its speed at rated load.

Last Answer : (A) 5 to 10%

If the no load voltage of a certain generator is 220V and the rated load voltage is 200V, then the voltage regulation is: a. 1% b. 10% c. 20V d. 9%

Description : If the no load voltage of a certain generator is 220V and the rated load voltage is 200V, then the voltage regulation is: a. 1% b. 10% c. 20V d. 9%

Last Answer : If the no load voltage of a certain generator is 220V and the rated load voltage is 200V, then the voltage regulation is: a. 1% b. 10% c. 20V d. 9%

To conduct load test on a dc shunt motor, it is coupled to a generator which is identical to the motor. The field

Description : To conduct load test on a dc shunt motor, it is coupled to a generator which is identical to the motor. The field of the generator is also connected to the same supply source as the motor. The armature of generator is ... value of this load resistance is  (A) 1.0 (B) 0.98 (C) 0.96 (D) 0.94

Last Answer : To conduct load test on a dc shunt motor, it is coupled to a generator which is identical to the motor. The field of the generator is also connected to the same supply source as the motor. ... obtain rated armature current in both motor and generator. The p.u value of this load resistance is 0.96

Which of the listed electrical devices is represented by the symbol shown in the illustration? EL-0055 A. Fixed resistance resistor B. Coil with magnetic core C. DC motor or generator shunt field D. Transformer

Description : Which of the listed electrical devices is represented by the symbol shown in the illustration? EL-0055 A. Fixed resistance resistor B. Coil with magnetic core C. DC motor or generator shunt field D. Transformer

Last Answer : Answer: D

A d.c. shunt motor runs at no load speed of 1140 r.p.m. At full load, armature reaction weakens the main flux by 5% whereas the armature circuit voltage drops by 10%. The motor full load speed in r.p.m. is (A) 1080 (B) 1203 (C) 1000 (D) 1200

Description : A d.c. shunt motor runs at no load speed of 1140 r.p.m. At full load, armature reaction weakens the main flux by 5% whereas the armature circuit voltage drops by 10%. The motor full load speed in r.p.m. is (A) 1080 (B) 1203 (C) 1000 (D) 1200

Last Answer : (A) 1080

If a three-phase induction motor is operated under a light load and it develops an open in one of its supply lines, the motor will _____________. A. continue to run, but will vibrate and have reduced torque B. speed up due to the reduced number of poles C. run cooler due to reduced current flow D. stop

Description : If a three-phase induction motor is operated under a light load and it develops an open in one of its supply lines, the motor will _____________. A. continue to run, but will vibrate and have reduced ... speed up due to the reduced number of poles C. run cooler due to reduced current flow D. stop

Last Answer : Answer: A

In a diesel electric plant, raising the generator's field excitation will cause the DC propulsion motor to ________. A. increase in speed B. decrease in speed C. affect generator speed only D. affect main motor speed if done in conjunction with higher generator engine speeds

Description : In a diesel electric plant, raising the generator's field excitation will cause the DC propulsion motor to ________. A. increase in speed B. decrease in speed C. affect generator speed only D. affect main motor speed if done in conjunction with higher generator engine speeds

Last Answer : Answer: A

58 If a pump motor is run on 2/3rd of its supply voltage, it will A. Continue to deliver same power B. burn C. stall D. continue to run at lower speed

Description : 58 If a pump motor is run on 2/3rd of its supply voltage, it will A. Continue to deliver same power B. burn C. stall D. continue to run at lower speed

Last Answer : C. Stall

A cumulative dc compound motor runs at 1500 rpm. on full load. If its series field is short-circuited, its speed

Description : A cumulative dc compound motor runs at 1500 rpm. on full load. If its series field is short-circuited, its speed  (1) becomes zero (2) remains unchanged (3) increases (4) decreases

Last Answer : Increases. As it's cumulative compound motor, both series and shunt field both assist each other. If series field is short circuited, the overall field strength will decrease and atop of that ... speed is inversely proportional to field strength.  So, the speed will increase overall.

The prime mover of an AC two pole main propulsion generator drives the generator at 3600 RPM. If the main propulsion motor has 80 poles, what will be the propeller speed? A. 45 RPM B. 80 RPM C. 90 RPM D. 180 RPM

Description : The prime mover of an AC two pole main propulsion generator drives the generator at 3600 RPM. If the main propulsion motor has 80 poles, what will be the propeller speed? A. 45 RPM B. 80 RPM C. 90 RPM D. 180 RPM

Last Answer : Answer: C

As shown in the illustration, when the 'speed control' system is in 'SPLIT' _______________. EL-0096 A. Relays #1, #5 and #8 are not used B. the 'slew rated controller' is grounded through Relay #6 C. the RPM 'function generator' and 'thrust levers' have no control D. the 'E/P converters' are bypassed and air is fed directly to the governors via the 'load sharing valve'

Description : As shown in the illustration, when the 'speed control' system is in 'SPLIT' _______________. EL-0096 A. Relays #1, #5 and #8 are not used B. the 'slew rated controller' is grounded through Relay ... E/P converters' are bypassed and air is fed directly to the governors via the 'load sharing valve'

Last Answer : Answer: C

An 8 pole lap wound DC shunt generator is supplying 295A to a load. The field current of the generator is 5A....

Description :  An 8 pole lap wound DC shunt generator is supplying 295A to a load. The field current of the generator is 5A. The current per parallel path is: -  a) 300A b) 200A c) 150A d) 37.5A

Last Answer :  An 8 pole lap wound DC shunt generator is supplying 295A to a load. The field current of the generator is 5A. The current per parallel path is: - 37.5A

An alternator is delivering rated current at rated voltage and 0.8 power-factor lagging case. If it is required to deliver rated current at rated voltage and 0.8 power-factor leading, the required excitation will be (A) less. (B) more. (C) more or less. (D) the same.

Description : An alternator is delivering rated current at rated voltage and 0.8 power-factor lagging case. If it is required to deliver rated current at rated voltage and 0.8 power-factor leading, the required excitation will be (A) less. (B) more. (C) more or less. (D) the same.

Last Answer : Ans: B Over excitation gives leading power factor and under excitation gives lagging p.f .

A balanced three-phase, 50 Hz voltage is applied to a 3 phase, 4 pole, induction motor. When the motor is delivering rated output, the slip is found to be 0.05. The speed of the rotor m.m.f. relative to the rotor structure is (A) 1500 r.p.m. (B) 1425 r.p.m. (C) 25 r.p.m. (D) 75 r.p.m.

Description : A balanced three-phase, 50 Hz voltage is applied to a 3 phase, 4 pole, induction motor. When the motor is delivering rated output, the slip is found to be 0.05. The speed of the rotor m.m.f. relative to the rotor structure is (A) 1500 r.p.m. (B) 1425 r.p.m. (C) 25 r.p.m. (D) 75 r.p.m.

Last Answer : (D) 75 r.p.m.

The speed of a multi-speed, squirrel-cage, induction motor operating in a fixed frequency system can be changed by _____________. A. reconnecting stator windings for different numbers of poles B. changing the RPM of the rotor flux C. changing the phase sequence of the applied voltage D. reconnecting the stator so that no poles have the same polarity

Description : The speed of a multi-speed, squirrel-cage, induction motor operating in a fixed frequency system can be changed by _____________. A. reconnecting stator windings for different numbers of poles B. ... sequence of the applied voltage D. reconnecting the stator so that no poles have the same polarity

Last Answer : Answer: A

An open armature connection in a DC propulsion motor could be caused by ____________. A. low-load operation B. clogged ventilation ducts C. sparking at the brushes D. a grounded shunt field coil

Description : An open armature connection in a DC propulsion motor could be caused by ____________. A. low-load operation B. clogged ventilation ducts C. sparking at the brushes D. a grounded shunt field coil

Last Answer : Answer: B

Regenerative braking (A) Can be used for stopping a motor. (B) Cannot be easily applied to DC series motors. (C) Can be easily applied to DC shunt motors (D) Cannot be used when motor load has overhauling characteristics.

Description : Regenerative braking (A) Can be used for stopping a motor. (B) Cannot be easily applied to DC series motors. (C) Can be easily applied to DC shunt motors (D) Cannot be used when motor load has overhauling characteristics.

Last Answer : Ans: B Because reversal of Ia would also mean reversal of field and hence of Eb

In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 1 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal ... 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: A

In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

A short in the shunt field of a DC motor is best located by _____________. A. visual inspection of the commutator B. applying AC voltage to each field coil and measuring the voltage drop across each field coil C. using a growler and hacksaw blade D. isolating each coil from the others and using a megohmmeter

Description : A short in the shunt field of a DC motor is best located by _____________. A. visual inspection of the commutator B. applying AC voltage to each field coil and measuring the voltage drop across ... using a growler and hacksaw blade D. isolating each coil from the others and using a megohmmeter

Last Answer : Answer: B

Which of the following actions must be carried out before a voltage tester can be used to test the three line fuses to a three-phase motor? A. The fuses must be removed from the circuit. B. The starter must be placed in the STOP position to stop the motor. C. The three line connections in the motor terminal box must be disconnected and tagged. D. Nothing need be done as long as the motor is running under a light load.

Description : Which of the following actions must be carried out before a voltage tester can be used to test the three line fuses to a three-phase motor? A. The fuses must be removed from the circuit. B. The ... disconnected and tagged. D. Nothing need be done as long as the motor is running under a light load.

Last Answer : Answer: B

A salient pole synchronous motor is running at no load. Its field current is switched off. The motor will (A) come to stop. (B) continue to run at synchronous speed. (C) continue to run at a speed slightly more than the synchronous speed. (D) continue to run at a speed slightly less than the synchronous speed.

Description : A salient pole synchronous motor is running at no load. Its field current is switched off. The motor will (A) come to stop. (B) continue to run at synchronous speed. (C) continue to run at ... more than the synchronous speed. (D) continue to run at a speed slightly less than the synchronous speed.

Last Answer : (B) continue to run at synchronous speed.

If the connections for the field and the armature on a DC motor are reversed, _____________. A. the motor will run as a generator B. the motor will not run C. the direction of rotation will be the same D. the direction of rotation will be reversed

Description : If the connections for the field and the armature on a DC motor are reversed, _____________. A. the motor will run as a generator B. the motor will not run C. the direction of rotation will be the same D. the direction of rotation will be reversed

Last Answer : Answer: C

A 3-phase 50HZ SCIM takes a power input of 30 KW at its full load speed of 1440 rpm. Total stator losses are 1 KW. The slip and rotor ohmic losses at full load are a) 0.02, 600 W b) 0.04, 580 W c) 0.04, 1160 W d) 0.04, 1200 W

Description : A 3-phase 50HZ SCIM takes a power input of 30 KW at its full load speed of 1440 rpm. Total stator losses are 1 KW. The slip and rotor ohmic losses at full load are a) 0.02, 600 W b) 0.04, 580 W c) 0.04, 1160 W d) 0.04, 1200 W

Last Answer : Ans: 0.04, 1160 W

The distance between a generator and its load is 100 feet. What would be the approximate total voltage drop across a two wire supply cable if the current were 5.5 amperes and the resistance of the wire were 2.525 ohms per 1,000 feet? A. 0.5 volts B. 1.38 volts C. 1.90 volts D. 2.77 volts

Description : The distance between a generator and its load is 100 feet. What would be the approximate total voltage drop across a two wire supply cable if the current were 5.5 amperes and the resistance of the wire were 2.525 ohms per 1,000 feet? A. 0.5 volts B. 1.38 volts C. 1.90 volts D. 2.77 volts

Last Answer : Answer: D

What are the reason of fall of terminal voltage of a D.C.Shunt generator?

Description : What are the reason of fall of terminal voltage of a D.C.Shunt generator?

Last Answer : As the load current increases, the terminal voltage tends todrop due to increased current and drop in voltage due to internalwinding resistance.

Why does the speed of a DC shunt motor decrease as the load increases?

Description : Why does the speed of a DC shunt motor decrease as the load increases?

Last Answer : Because if the load is increasing then the torque must also be increase. If not then the speed of motor will decrease.

A 240 V, dc shunt motor draws 15 A while supplying the rated load at a speed of 80 rad/s.

Description : A 240 V, dc shunt motor draws 15 A while supplying the rated load at a speed of 80 rad/s. The armature resistance is 0.5 W and the field winding resistance is 80 W. The net Voltage across armature resistance at the time of plugging will be

Last Answer : A 240 V, dc shunt motor draws 15 A while supplying the rated load at a speed of 80 rad/s. The armature resistance is 0.5 W and the field winding resistance is 80 W. The net Voltage across armature resistance at the time of plugging will be 474 V

An unsaturated dc shunt motor runs at its rated speed when rated voltage is applied to it. If the

Description : An unsaturated dc shunt motor runs at its rated speed when rated voltage is applied to it. If the supply voltage to the motor is reduced by 25%, the speed of the motor  (a) Increases by 25% (b) Remains the same (c) Decreases by 25% (d) Decrease only slightly by an amount less than 25% 

Last Answer : An unsaturated dc shunt motor runs at its rated speed when rated voltage is applied to it. If the supply voltage to the motor is reduced by 25%, the speed of the motor Remains the same

As load is added to a shunt motor, the motor will _________. A. speed up B. continue to operate at the same speed C. slow down slightly D. stop

Description : As load is added to a shunt motor, the motor will _________. A. speed up B. continue to operate at the same speed C. slow down slightly D. stop

Last Answer : Answer: C