[31] With both S1 and S2 open, the core flux waveform will be [GATE 2009]
A. a sinusoidal at fundamental frequency
B. flat-topped with third harmonic
C. peaky with third-harmonic
D. none of these

1 Answer

Answer :

B. Flat topped with third harmonic

Related questions

Description : 32 With S2 closed and S1 open, the current waveform in the delta winding will be [GATE 2009] A. a sinusoidal at fundamental frequency B. flat-topped with third harmonic C. only third-harmonic D. none of these

Last Answer : C. Only third harmonic

Description : [53] The iron loss of the transformer is negligible during short circuit test because A. The entire input is just sufficient to meet Cu losses only B. Flux produced is a small fraction of the normal flux C. Iron core becomes fully saturated D. Supply frequency is held constant

Last Answer : B. Flux produced is a small fraction of the normal flux

Description : Why not reduce the noise in the core by reducing the amount of flux?

Last Answer : Transformer voltages are fixed by system requirements. The ratio of these voltages to the number of turns in the winding determines the amount of magnetization. This ratio of voltage to turns is determined ... flux at the normal voltage is fixed. This also fixes the level of noise and vibration.

Description : 27] In a transformer, the leakage flux of each winding is proportional to the current in that winding because A. Ohm's law applies to magnetic circuits B. Leakage paths do no saturate C. the two windings are electrically isolated D. mutual flux is confined to the core

Last Answer : B. Leakage path do not saturate

Description : 12] Which is not the basic element of the transformer? A. core B. primary winding C. secondary winding D. mutual flux

Last Answer : D. Mutual flux

Description : If the fundamental frequency is 200 megahertz, what is the third harmonic?

Last Answer : 600 megahertz.

Description : 46 The core used in high frequency transformer is usually A. Copper core B. Cost iron core C. Air core D.Mid steel core

Last Answer : C. Air core

Last Answer : The core used in high frequency transformer is usually air core .

Description : The output waveform produced due to time base generator in a CRO is a) saw tooth b) sinusoidal c) linear d) helical

Last Answer : a) saw tooth

Description : Describe the operation of inductor with sinusoidal AC voltage as input. Draw waveform for voltage across and current through the inductor. Draw its phasor representation.

Last Answer : An alternating voltage is applied to a purely inductive coil, a back e.m.f. is produced due to self-inductance of the coil. The back e.m.f. at every step, opposes the rise of fall of current through the coil ... drop, the applied voltage has to overcome this self induced e.m.f. only.

Description : Draw sinusoidal waveform of 3 phase emf and indicate the phase sequence.

Last Answer : Phase sequence is R-Y-B.

Description : 49 The open circuit test is carried out in a transformer to find the A. Cu loss B. Core loss C. Total loss D. Insulation resistance

Last Answer : B. Core loss

Description : When secondary of a current transformer is open-circuited its iron core will be?

Last Answer : When secondary of a current transformer is open-circuited its iron core will be hot because of heavy iron losses taking place in it due to high flux density.

Description : If coils 'R1-R2-R3' at the receiver of figure 'B' shown in the illustration turned opposite of those in the transmitter, what corrective action should be taken to have both turn in the same direction? EL-0092 A ... is needed. C. Interchange leads 'R1' and 'R3'. D. Interchange leads 'R2' and 'R3'.

Last Answer : Answer: C

Description : The statements s1 and s2 are given as: s1: Context sensitive languages are closed under intersection, concatenation, substitution and inverse homomorphism. s2: Context free languages are closed under complementation, ... is not correct and s2 is correct. (D) Both s1 and s2 are not correct.

Last Answer : (B) s1 is correct and s2 is not correct.

Description : A pushdown automation M = (Q, Σ, Γ, δ, q0, z, F) is set to be deterministic subject to which of the following condition(s), for every q ∈ Q, a ∈ Σ ∪ {λ} and b ∈ Γ (s1) δ(q, a, b) contains at most one ... ) must be empty for every c ∈ Σ (A) only s1 (B) only s2 (C) both s1 and s2 (D) neither s1 nor s2

Last Answer : (C) both s1 and s2

Description : Consider the following statements for priority queue: S1: It is a data structure in which the intrinsic ordering of the elements does determine the result of its basic operations. S2: The elements of a priority queue ... . (C) SI is incorrect and S2 is correct. (D) Both S1 and S2 are correct.

Last Answer : (D) Both S1 and S2 are correct.

Description : Which is the correct statement(s) for Non Recursive predictive parser? S1: First(α) = {t | α => * t β for some string β } => *tβ S2: Follow(X) = { a | S => * αXa β for some strings ... and S2 is correct. (C) S1 is correct and S2 is incorrect. (D) Both statements S1 and S2 are correct. 

Last Answer : (D) Both statements S1 and S2 are correct.

Description : Given the following statements: S1 : The grammars S→asb | bsa | ss | a and S→asb | bsa | a are not equivalent. S2: The grammars S→ss | sss | asb | bsa | λ and S→ss | asb | bsa | λ are equivalent. ... and S2 are correct (C) S1 is not correct and S2 is correct (D) Both S1 and S2 are not correct.

Last Answer : (A) S1 is correct and S2 is not correct.

Description : Consider the following statements S1 and S2 : S1 : A hard handover is one in which the channel in the source cell is retained and used for a while in parallel with the channel in the target cell. S2 : A soft handover ... and S2 is true. (C) Both S1 and S2 are true. (D) Both S1 and S2 are not true.

Last Answer : (D) Both S1 and S2 are not true.

Description : Given the following two statements: S1: If L1 and L2 are recursively enumerable languages over ∑, then L1⋃L2 and L1⋂L2 are also recursively enumerable. S2: The set of recursively enumerable languages is countable. ... correct (C) Both S1 and S2 are not correct (D) Both S1 and S2 are correct

Last Answer : (D) Both S1 and S2 are correct

Description : Consider the following statements : S1: A queue can be implemented using two stacks. S2: A stack can be implemented using two queues. Which of the following is correct ? (A) S1 is correct and S2 is not correct. ( ... S2 is correct. (C) Both S1 and S2 are correct. (D) Both S1 and S2 are not correct.

Last Answer : (C) Both S1 and S2 are correct.

Description : Consider following schedules involving two transactions: S1: r1(X); r1(Y); r2(X); r2(Y); w2(Y); w1(X) S2: r1(X); r2(X); r2(Y); w2(Y); r1(Y); w1(X) Which of the following ... . (3) S1 is not conflict serializable and S2 is conflict serializable. (4) Both S1 and S2 are not conflict serializable.

Last Answer : S1 is not conflict serializable and S2 is conflict serializable.

Description : An open pipe is suddenly closed at one end with the result that the frequency of third harmonic of he closed pipe is found to be higher by 100 Hx than

Last Answer : An open pipe is suddenly closed at one end with the result that the frequency of third harmonic of he closed pipe ... 300 Hz` C. `240 Hz` D. `480 Hz`

Description : Explain the sinusoidal harmonic reduction techniques for cylcoconverters.

Last Answer : sinusoidal

Description : Given the following Series S1 and S2: Write the command to find the sum of series S1 and S2 -Technology

Last Answer : print(S1+S2)

Description : If coils 'R1-R2-R3' at the receiver of figure 'B' shown in the illustration turned opposite of those in the transmitter by design, what corrective action should be taken? EL-0092 A. Reverse the 60 Hz supply ... is needed. C. Interchange leads 'R1' and 'R3'. D. Interchange leads 'R2' and 'R3'.

Last Answer : Answer: B

Description : The direction of rotation of the winch shown in the illustration is changed by reversing the _____________. EL-0102 A. direction of current through the shunt field B. polarity of voltage at 'S1' and 'S2' C. direction of current through the armature D. polarity of voltage at 'L1' and 'L2'

Last Answer : Answer: C

Description : If coils 'R1-R2-R3' at the receiver of figure 'B' shown in the illustration were in 180 degree error with those of the transmitter, what corrective action should be taken? EL-0092 A. Reverse the 60 Hz ... is proper operation. C. Interchange leads 'R1' and 'R3'. D. Interchange leads 'R2' and 'R3'.

Last Answer : Answer: A

Description : If coil 'R1-R2' at the receiver of figure 'A' shown in the illustration were in 180 degree error with respect to that of the transmitter, what corrective action should be taken? EL-0092 A. No action is ... and 'R2'. C. Interchange connections 'S1' and 'S2'. D. Interchange connections 'S1' and 'S3'.

Last Answer : Answer: B

Description : If coil 'R1-R2' at the receiver of figure 'A' shown in the illustration turned opposite of that in the transmitter, what corrective action should be taken? EL-0092 A. No action is necessary as this is ... . C. Interchange connections to 'S1' and 'S2'. D. Interchange connections to 'S1' and 'S3'.

Last Answer : Answer: D

Description : If coil 'R1-R2' on the transmitter in figure 'A' shown in the illustration is turned 30 degrees clockwise, corresponding coil 'R1-R2' on the receiver should ____________. EL-0092 A. make coils 'S1 ... a higher voltage depending on the turns ratio D. align itself to the same position if free to move

Last Answer : Answer: D

Description : If = = in the system of equations a 1 x + b 1 y + c 1 = 0 and a 2 x + b 2 y + c 2 = 0 Statement 1 : This is the condition for inconsistent equations Statement 2 : There exists infinitely many solutions ... statements are true ? e) S1 only f) S1 and S2 g) S1 and S3 h) S2 only Answer: (d) S2 o

Last Answer : h) S2 only

Description : If = = in the system of equations a 1 x + b 1 y + c 1 = 0 and a 2 x + b 2 y + c 2 = 0 Statement 1 : This is the condition for inconsistent equations Statement 2 : There exists infinitely many ... parallel Which of the above statements are true ? a) S1 only b) S1 and S2 c) S1 and S3 d) S2 only

Last Answer : d) S2 only

Description : Derivation of Thiem's formula Q = 2 (s1 - s2)/2.3 log10 (r2/r1) is based on the assumption  (A) The aquifer is homogeneous, isotropic and of infinite depth and area  (B) The well is sunk ... (C) The flow lines are radial and horizontal, and the flow is laminar  (D) All the above 

Last Answer : (D) All the above 

Description : S1 and S2 are the draw downs in an observation well at times t1 and t2 after pumping. For  discharge Q and coefficient of transmissibility T, the relationship, is  (A) S2 - S1 = (2.3Q/ ) log10 (t2/t1)  (B) S2 - S1 ... - S1 = (2.3Q/4 ) loge (t2/t1)  (D) S2 - S1 = (2.3Q/4 ) loge (t1/t2

Last Answer : (B) S2 - S1 = (2.3Q/4 ) log10 (t2/t1) 

Description : the derivation of Thiem's formula, Q = (S1 - S2)/[2.3 log10( / )] the following assumption is not applicable (A) The aquifer is homogeneous and isotropic (B) Flow lines are radial and ... the water surface is too small (D) The well has been sunk up to the surface of the unconfined aquifer

Last Answer : Answer: Option D

Description : With the inputs shown below, what will be the output of S1, S2, and C2?

Last Answer : MSD of the sum.

Description : Given the following statements: S1: Every context-sensitive language L is recursive. S2: There exists a recursive language that is not context sensitive. Which statement is correct? (A) S1 is not correct and S2 is ... (C) S1 is correct and S2 is not correct. (D) S1 is correct and S2 is correct.

Last Answer : (D) S1 is correct and S2 is correct. 

Description : Given the following statements : S1 : If L is a regular language then the language {uv | uϵL, vϵLR} is also regular. S2 : L = {wwR} is regular language. Which of the following is true ? (A) S1 is not ... S2 is correct. (C) S1 is correct and S2 is not correct. (D) S1 is correct and S2 is correct.

Last Answer : (C) S1 is correct and S2 is not correct.

Description : Given the following statements : S1 : SLR uses follow information to guide reductions. In case of LR and LALR parsers, the look-aheads are associated with the items and they make use of the left context available to ... (C) S1 is correct and S2 is not correct. (D) S1 is correct and S2 is correct.

Last Answer : (D) S1 is correct and S2 is correct.

Description : Given the following statements :  S1 : The subgraph-isomorphism problem takes two graphs G1 and G2 and asks whether G1 is a subgraph of G2.  S2 : The set-partition problem takes as input a set S of numbers and ... S1 is P problem and S2 is P problem. (D) S1 is P problem and S2 is NP problem.

Last Answer : (B) S1 is NP problem and S2 is NP problem.

Description : Which of the following statement(s) is/are true with respect to software architecture? S1: Coupling is a measure of how well the things grouped together in a module belong together logically. S2: Cohesion is a measure of the ... ) Only S1 and S2 (2) Only S3 (3) All of S1, S2 and S3 (4) Only S1

Last Answer : Answer: 2

Description : A body is vibrating with simple harmonic motion of aplitude 5 cm frequency 10 vibrations per second. The maximum value of velocity in cm/s will be a.3.14 cm/s b.314 cm/s c.3140 cm/s d.31.4 cm/s e.31400 cm/s

Last Answer : b. 314 cm/s

Description : What are the factors affecting the selection of Maximum flux density?

Last Answer : 1. Net core weight: Higher the flux density lesser net weight of core. 2.Saving in copper:Higher the flux density lesser mean turn of windings. 3.Overall economy: Higher the flux ... High Flux density results in high losses and hence efficiency decreases 8.Hence high temperature rise and noise

Description : 68 The path of a magnetic flux in a transformer should have A. High resistance B. High reluctance C. Low resistance D. Low reluctance

Last Answer : D. Low reluctance

Description : 38] In a transformer the energy is conveyed from primary to secondary? A. Through cooling coil B. Through air C. By the flux D. None of the above

Last Answer : C. By the flux