60)The noise resulting from vibrations of laminations set by magnetic force, is termed as
A. magnetostriction
B. boo
C. hum
D. zoom

1 Answer

Answer :

C. Hum

Related questions

Description : 69 In case there are burrs on the edges of the laminations of the transformer, it is likely to result in A. Vibrations B. Noise C. Higher eddy currents loss D. Higher hysteresis loss

Last Answer : C. Higher eddy currents loss

Description : 61 The degree of mechanical vibrations produced by the laminations of a transformers depends on A. Tightness of clamping B. Gauge of laminations C. Size of laminations D. All of the above

Last Answer : D. All of the above

Description : In a power transformer, the fundamental frequency of the hum arising due to magnetostriction is  (a) equal to the line frequency (b) double the line frequency (c) 4 times the line frequency (d) not related to the line frequency

Last Answer : In a power transformer, the fundamental frequency of the hum arising due to magnetostriction is double the line frequency

Description : 77 The transformer laminations are insulated from each other by A. Mica strip B. Thin coat of varnish C. Paper D. Any of the above

Last Answer : B. Thin coat of varnish

Description : 70] Silicon steel used in laminations mainly reduces A. Hysteresis loss B. Eddy current losses C. Copper loss D. All of the above

Last Answer : A. Hysteresis loss

Description : 19 Transformer cores are built up from laminations rather than from solid metal so that A. Oil penetrates the core more easily B. Eddy current loss is reduced C. Less lamination is required for the windings D. Turn ratio is higher than voltage ratio

Last Answer : B. Eddy current loss is reduced

Last Answer : The thickness of laminations used in a transformer is usually 0.4 mm to 0.5 mm.

Last Answer : Silicon steel used in laminations mainly reduces hysteresis loss.

Last Answer : The transformer laminations are insulated from each other by thin coat of varnish.

Description : The noise produced by a transformer is termed as?

Last Answer : The noise produced by a transformer is termed as hum.

Description : Why do transformers hum?

Last Answer : Transformer noise is caused by a phenomenon which causes a piece of magnetic sheet steel to extend itself when magnetized. When the magnetization is taken away, it goes back to its original condition ... core. The degree of flux determines the amount of magnetostriction and hence, the noise level.

Description : The hum in a transformer is mainly attributed to?

Last Answer : The hum in a transformer is mainly attributed to magnetostriction.

Description : The major reason of hydrodynamic noise (i.e., noise resulting from liquid flow) is (A) Pipe vibrations (B) Cavitation (C) Boundary layer separation (D) Fluctuation in liquid flow

Last Answer : (B) Cavitation

Description : The phenomenon of magnetostriction occurs when a ferromagnetic substance is magnetized resulting in (a) Heating (b) Small changes in its dimensions (c) Small changes in its crystal structure (d) Some change in its mechanical properties

Last Answer : The phenomenon of magnetostriction occurs when a ferromagnetic substance is magnetized resulting in Small changes in its dimensions 

Description : 10] The main reason for generation of harmonics in a transformer could be A. Fluctuating load B. Poor insulation C. Mechanical vibrations D. Saturation of core

Last Answer : D) saturation of core

Description : The degree of mechanical vibrations produced by the laminations of a transformer depends on?

Last Answer : The degree of mechanical vibrations produced by the laminations of a transformer depends on tightness of clamping, gauge of laminations, size of laminations.

Description : Why not reduce the noise in the core by reducing the amount of flux?

Last Answer : Transformer voltages are fixed by system requirements. The ratio of these voltages to the number of turns in the winding determines the amount of magnetization. This ratio of voltage to turns is determined ... flux at the normal voltage is fixed. This also fixes the level of noise and vibration.

Description : What is the cause of noise in transformer?

Last Answer : The cause of noise in the transformer is mainly because of magnetostriction effect and also loosening of stampings and mechanical forces produced during working.

Last Answer : Noise level test in a transformer is a type test.

Last Answer : Transformer noise is generated due to vibration of core and winding this is because of magnetostriction and magnetomotive force.

Description : The reason for non existence of magnetic monopoles is a) The magnetic field cannot be split b) Due to permeability c) Due to magnetization d) Due to magnetostriction

Last Answer : a) The magnetic field cannot be split

Description : The energy in a magnetic material is due to which process? a) Emf b) Magnetization c) Magnetostriction d) Polarization

Last Answer : b) Magnetization

Description : The converse of magnetostriction is called the a) Magnetization b) Magnetic anisotropy c) Villari effect d) Curie effect

Last Answer : c) Villari effect

Description : Can 60 Hz Transformers be Used at Higher Frequencies?

Last Answer : A: Transformers can be used at fre¬quencies above 50 Hz up through 400 Hz with no limitations provided nameplate voltages are not exceeded. However, 50 Hz transformers will have less voltage ... Where better regulation and smaller physical size are required, contact us for special 400 Hz designs.

Description : Can 60 Hz transformers be operated at 50 Hz?

Last Answer : The transformers rated below 1 KVA can be used on 50 Hz service. Transformers 1 KVA and larger, rated at 60 Hz, should not be used on 50 Hz service, due to the higher losses and resultant heat ... designs are required for this service. However, any 50 Hz transformer will operate on a 60 Hz service.

Description : Why the efficiency of distribution transformer is 60 to 70 % and not 100%?

Last Answer : Distribution transformer is designed for maximum efficiency at 60% to 70% load as it normally doesn't operate at full load all the time. Its load depends on distribution demand. Whereas power transformer ... efficiency at 100% load as it always runs at 100% load being near to generating station.

Description : How is magnetic leakage reduced to a minimum in commercial transformers?

Last Answer : By interleaving the primary and secondary windings.

Description : 72 Harmonics in transformer result in A. Increased core losses B. Increased I2R losses C. Magnetic interference with communication circuits D. All of the above

Last Answer : D. All of the above

Description : 68 The path of a magnetic flux in a transformer should have A. High resistance B. High reluctance C. Low resistance D. Low reluctance

Last Answer : D. Low reluctance

Description : 43 The purpose of providing an iron core in a transformer is to A.Provide support to windings B. Reduce hysteresis loss C. decrease the reluctance of the magnetic path D. reduce eddy current losses

Last Answer : C. Decrease the reluctance of the magnetic path

Description : 27] In a transformer, the leakage flux of each winding is proportional to the current in that winding because A. Ohm's law applies to magnetic circuits B. Leakage paths do no saturate C. the two windings are electrically isolated D. mutual flux is confined to the core

Last Answer : B. Leakage path do not saturate

Description : 21.The ordinary two winding transformer's primary and secondary windings always have A. different no of turns B. same size of copper wire C. a common magnetic circuit D. separate magnetic circuits

Last Answer : C. A common magnetic circuit

Description : The path of magnetic flux in a transformer should have?

Last Answer : The path of magnetic flux in a transformer should have low reluctance.

Description : The air gap in an induction motor should be checked periodically with a feeler gage to detect ____________. A. rotor contact with the laminations B. changes in armature magnetic strength C. excessive bearing wear D. electrical damage to the rotor

Last Answer : Answer: C

Description : In damped vibrations, the amplitude of the resulting vibration gradually reduces. This is due to the reason that an amount of energy is always dissipated to overcome the ________ * 1 point (A) Frictional resistance (B) Work done(C) Fluid pressure (D) Air pressure

Last Answer : (A) Frictional resistance

Description : In damped vibrations, the amplitude of the resulting vibration gradually reduces. This is due to the reason that an amount of energy is always dissipated to overcome the ________ a) Frictional resistance b) Work done c) Fluid pressure d) Air pressure

Last Answer : a) Frictional resistance

Description : In damped vibrations, the amplitude of the resulting vibration gradually diminishes. a) True b) False

Last Answer : a) True

Description : A control system with excessive noise, is likely to suffer from (a) saturation in amplifying stages (b) loss of gain (c) vibrations (d) oscillations

Last Answer : Ans: A

Description : Major sources of noise in furnace operation arises from air inspirators, combustion, side wall vibrations and fluctuation in the process heat load. A 50% increase in fuel firing rate may increase the furnace noise level by about __________ decibels. (A) 3 (B) 30 (C) 7 (D) 70

Last Answer : (A) 3

Description : An increase in the number of new cells in an organ or tissue that is reversible when the stimulus for production of new cells is removed is termed a) Hyperplasia. Hyperplasia occurs as cells multiply ... in the number of new cells in an organ or tissue continues after the stimulus is removed.

Last Answer : a) Hyperplasia. Hyperplasia occurs as cells multiply and are subjected to increased stimulation resulting in tissue mass enlargement.

Description : Piezoelectric effect is analogous to which phenomenon? a) Electrostriction b) Magnetostriction c) Anisotropy d) Magnetization

Last Answer : b) Magnetostriction

Description : The property due to which the resistance of some metal or compound vanishes under certain conditions is (A) Semi conductivity. (B) Super conductivity. (C) Curie point. (D) Magnetostriction.

Last Answer : (B) Super conductivity.

Description : Explain magnetostriction property. Explain generation of ultrasonic using magnetostriction

Last Answer : When a ferromagnetic material is magnetized then the material exhibit small change in its dimensions, this phenomenon is called magnetostriction effect. Iron crystal expands when magnetized in ... waves  1.ultrasonic signaling 2.ultrasonic cleaning 3.ultrasonic soldering 4.ultrasonic drilling.

Description : Noise occurring in the presence of signal resulting from a mismatch between the exact value of an analog signal and the closet available quantizing step in a digital coder. A. Quantizing noise B. Thermal noise C. Impulse noise D. Crosstalk

Last Answer : A. Quantizing noise

Description : Pick out the wrong statement about cavitation. (A) Sudden reduction of pressure in a fluid flow system caused by flow separation, vortex formation or abrupt closing of valve leads to cavitation ... (D) Large scale cavitation cannot damage pipeline, restrict fluid flow and damage steam turbine blades

Last Answer : (D) Large scale cavitation cannot damage pipeline, restrict fluid flow and damage steam turbine blades

Description : Aerodynamic noise resulting from turbulent gas flow is the most prevalent source of valve noise in fluid flow control. It is caused due to (A) Reynold stresses (B) Shear forces (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Description : Do you watch, "Here Comes Honey Boo Boo?" and why?

Last Answer : Oh dear God no! Horrible show, glorifying low intelligence,stupidity and outright child abuse. Bah Humbug!

Description : Do you applaud or boo CNN for replacing seasoned Photojournalists with their "Citizen Journalism Initiative"?

Last Answer : answer:We need both. Photojournalists (as you so rightly point out) do more than just snap a few shots at incidents that happen when they are present. They tell stories with their photos. They have ... . They have different roles. Both valuable in their own way but one does not replace the other.

Description : Boo!

Last Answer : BOO TOO!!!

Description : New years day. I'm at work, there's no one here but me, and I've done nothing but Fluther all day long! Hooray or boo for me?

Last Answer : Monitor those lines in 2009