The e.m.f. induced in the primary of a transformer: ...

The e.m.f. induced in the primary of a transformer: 

(A) is in phase with the flux (B) lags behind the flux by 90 degree (C) leads the flux by 90 degree (D) is in phase opposition to that of flux
by

1 Answer

Answer :

The e.m.f. induced in the primary of a transformer: leads the flux by 90 degree 

by

Related questions

Mention the factors on which the magnitude of the e.m.f induced in the transformer depends.

Description : Mention the factors on which the magnitude of the e.m.f induced in the transformer depends.

Last Answer : 1) E.m.f in the primary coil 2) Number of turns in the primary coil 3) Number of turns in the secondary coil 4) The core material

Which of the following quantity maintains the same direction whether a D.C. machine runs as a generator or as a motor a. Induced e.m.f. b. Armature Current c. Field Current d. Supply Current

Description : Which of the following quantity maintains the same direction whether a D.C. machine runs as a generator or as a motor a. Induced e.m.f. b. Armature Current c. Field Current d. Supply Current  

Last Answer : Which of the following quantity maintains the same direction whether a D.C. machine runs as a generator or as a motor a. Induced e.m.f. b. Armature Current c. Field Current d. Supply Current  

Which law states that induced e.m.f and current always opposes the cause producing them?

Description : Which law states that induced e.m.f and current always opposes the cause producing them?

Last Answer : Lenz's law states that induced e.m.f and current always opposes the cause producing them.

These self inductance of a circuit is defined as twice the work done against the induced e.m.f.

Description : These self inductance of a circuit is defined as twice the work done against the induced e.m.f. on establishing unit current in the coil. If the current to be established in the coil is doubled, the work done ... induced e.m.f. will be  1. Doubled  2. Halved  3. four times  4. Quarter times 

Last Answer : These self inductance of a circuit is defined as twice the work done against the induced e.m.f. on establishing unit current in the coil. If the current to be established in the coil is doubled, the work done against the induced e.m.f. will be four times

For the production of induced e.m.f. field system of an electric machine_________.

Last Answer : For the production of induced e.m.f. field system of an electric machine may be on stator or rotor.

In transformer, alternating current is induced inA. primary coilB. secondary coilC. iron coreD. resistor

Description : In transformer, alternating current is induced inA. primary coil B. secondary coil C. iron core D. resistor

Last Answer : primary coil

28.In a two winding transformer, the emf /turn in secondary winding is always......the induced emf power turn in primary A. equal to k times B. equal to 1/k times C. equal D. greater than

Description : 28.In a two winding transformer, the emf /turn in secondary winding is always......the induced emf power turn in primary A. equal to k times B. equal to 1/k times C. equal D. greater than

Last Answer : C. equal

6 In a two winding transformer, the primary and secondary induced emf E1 & E2 are always A. equal in magnitude B. anti phase with each other C. in phase with each other D. determined by load on transformer secondary

Description : 6 In a two winding transformer, the primary and secondary induced emf E1 & E2 are always A. equal in magnitude B. anti phase with each other C. in phase with each other D. determined by load on transformer secondary

Last Answer : C. In phase with each other

The emf induced in the primary of a transformer (A) is in phase with the flux. (B) lags behind the flux by 90 degree. (C) leads the flux by 90 degree. (D) is in phase opposition to that of flux.

Description : The emf induced in the primary of a transformer (A) is in phase with the flux. (B) lags behind the flux by 90 degree. (C) leads the flux by 90 degree. (D) is in phase opposition to that of flux.

Last Answer : (C) leads the flux by 90 degree.

What is the back E.M.F in Transformer ?

Description : What is the back E.M.F in Transformer ?

Last Answer : Back emf in transformer is when apply voltage in primary side of transformer. This voltage produce flux according to Faraday law electro magnetic induction. This flux called mutual flux and this ... secondary flux oppos the applied voltage according to lenz law. its called back emf of transformer

Magnitude of induced e.m.f is proportional to A. rate of change of current B. rate of change of voltage C. rate of change of magnetic flux linkage D. rate of change of resistance

Description : Magnitude of induced e.m.f is proportional to A. rate of change of current B. rate of change of voltage C. rate of change of magnetic flux linkage D. rate of change of resistance

Last Answer : rate of change of magnetic flux linkage

A straight wire of length 0.20 m moves at a steady speed of 3.0 m s-1 at right angles to the magnetic field of flux density 0.10 T. The e.m.f induced across ends of wire is A. 0.5 V B. 0.06 V C. 0.05 V D. 0.04 V

Description : A straight wire of length 0.20 m moves at a steady speed of 3.0 m s-1 at right angles to the magnetic field of flux density 0.10 T. The e.m.f induced across ends of wire is A. 0.5 V B. 0.06 V C. 0.05 V D. 0.04 V

Last Answer : 0.06 V

E.M.F can be induced in a circuit by A. changing magnetic flux density B. changing area of circuit C. changing the angle D. all of above

Description : E.M.F can be induced in a circuit by A. changing magnetic flux density B. changing area of circuit C. changing the angle D. all of above

Last Answer : all of above

The left hand rule correlates to (a) current, induced e.m.f. and direction of force on a conductor (b) magnetic field, electric field and direction of force on a conductor (c) self induction, mutual induction and direction of force on a conductor (d) current, magnetic field and direction of force on a conductor

Description : The left hand rule correlates to (a) current, induced e.m.f. and direction of force on a conductor (b) magnetic field, electric field and direction of force on a conductor (c) self induction, ... and direction of force on a conductor (d) current, magnetic field and direction of force on a conductor

Last Answer : (d) current, magnetic field and direction of force on a conductor

The introduction of interpoles in between the main pole improves the performance of d.c. machines, because (A) The interpole produces additional flux to augment the developed torque. (B) The flux waveform is improved with reduction in harmonics. (C) The inequality of air flux on the top and bottom halves of armature is removed. (D) A counter e.m.f. is induced in the coil undergoing commutation.

Description : The introduction of interpoles in between the main pole improves the performance of d.c. machines, because (A) The interpole produces additional flux to augment the developed torque. (B) The flux waveform is ... armature is removed. (D) A counter e.m.f. is induced in the coil undergoing commutation.

Last Answer : Ans: D Counter e.m.f is produced, it neutralizes the reactive emf.

The voltage regulation of an alternator having 0.75 leading p.f. load, no-load induced e.m.f. of 2400V and ...

Description : The voltage regulation of an alternator having 0.75 leading p.f. load, no-load induced e.m.f. of 2400V and rated terminal voltage of 3000V is —————————————  A) 20% B) —20% C) 150 D) -26.7

Last Answer : -20

When a magnet is in motion relative to a coil the induced e.m.f. does not depend upon

Last Answer : When a magnet is in motion relative to a coil the induced e.m.f. does not depend upon resistance of the coil.

The induced e.m.f. in the armature conductors of a d.c. motor is?

Description : The induced e.m.f. in the armature conductors of a d.c. motor is?

Last Answer : The induced e.m.f. in the armature conductors of a d.c. motor is sinusoidal.

If residual magnetism is present in a D.C. generator, the induced e.m.f. at zero speed will be?

Description : If residual magnetism is present in a D.C. generator, the induced e.m.f. at zero speed will be?

Last Answer : If residual magnetism is present in a D.C. generator, the induced e.m.f. at zero speed will be zero.

In any rotating machine that part which houses the conductors and in which e.m.f. induced is to be utilised is called?

Last Answer : In any rotating machine that part which houses the conductors and in which e.m.f. induced is to be utilised is called armature.

The e.m.f. induced in the armature of a shunt generator is 600 V. The armature resistance is 0.1 ohm...

Description : The e.m.f. induced in the armature of a shunt generator is 600 V. The armature resistance is 0.1 ohm. If the armature current is 200 A, the terminal voltage will be?

Last Answer : The e.m.f. induced in the armature of a shunt generator is 600 V. The armature resistance is 0.1 ohm. If the armature current is 200 A, the terminal voltage will be 580 V.

If B is the flux density, I the length of conductor and v the velocity of conductor, then induced e.m.f. is given by?

Last Answer : If B is the flux density, I the length of conductor and v the velocity of conductor, then induced e.m.f. is given by Blv.

While applying Fleming's right-hand rule to And the direction of induced e.m.f., the thumb points towards?

Last Answer : While applying Fleming's right-hand rule to And the direction of induced e.m.f., the thumb points towards direction of motion of conductor, if forefinger points along the lines of flux.

Fleming's right-hand rule regarding direction of induced e.m.f., correlates?

Last Answer : Fleming's right-hand rule regarding direction of induced e.m.f., correlates magnetic flux, direction of motion and the direction of e.m.f. induced.

According to Fleming's right-hand rule for finding the direction of induced e.m.f...

Description : According to Fleming's right-hand rule for finding the direction of induced e.m.f., when middle finger points in the direction of induced e.m.f., forefinger will point in the direction of?

Last Answer : According to Fleming's right-hand rule for finding the direction of induced e.m.f., when middle finger points in the direction of induced e.m.f., forefinger will point in the direction of lines of force.

When the armature of a D.C. motor rotates, e.m.f. induced is

Last Answer : When the armature of a D.C. motor rotates, e.m.f. induced is back e.m.f.

Why the earthing transformer primary voltage is 16.5 kV rated in main generator even though actual voltage during the E/F is root 3 times less?

Description : Why the earthing transformer primary voltage is 16.5 kV rated in main generator even though actual voltage during the E/F is root 3 times less?

Last Answer : The transformer should not saturate during E/F otherwise it will cause ferroresonance with the GT winding capacitance. Dangerous O/V and neutral shifting will occur. During loss of load or field ... saturation. Saturation can also occur due to point on wave of application causing flux doubling. 

The value of flux involved in the e.m.f. equation of a transformer is ?

Last Answer : Power on primary and secondary side of transformer A. Remains Approximately constant B. Are always different C. Is always 100kVA D. None of these

(a) Define permeability. (b) Define MMF. (c) Define form factor of an alternating quantity. (d) Define frequency and time period of an alternating quality. (e) Define transformation ratio of transformer. (f) State the EMF equation of a 1 transformer and state the meaning of each term used. (g) Give two applications of single phase motors.

Description : (a) Define permeability. (b) Define MMF. (c) Define form factor of an alternating quantity. (d) Define frequency and time period of an alternating quality. (e) Define transformation ratio of transformer. ... and state the meaning of each term used. (g) Give two applications of single phase motors. 

Last Answer : Permeability : It is the ability of a magnetic/Non magnetic material to allow setting up of flux in it.  MMF : The magneto motive force (MMF) is the force required to setup flux in a magnetic / ... applications of single phase motors : Water pumps, ceiling fan, lathe machine

The induced current in transformer which produced in the direction perpendicular to flux, is known as: a. Conventional current b. electronic current c. Perpendicular current d. Eddy current

Description : The induced current in transformer which produced in the direction perpendicular to flux, is known as: a. Conventional current b. electronic current c. Perpendicular current d. Eddy current

Last Answer : c. Perpendicular current

What will happen if the primary of a transformer is connected to D.C. supply?

Description : What will happen if the primary of a transformer is connected to D.C. supply?  (A) Transformer will operate with low efficiency (B) Transformer will operate with high efficiency (C) No effect (D) Transformer may start to smoke and burn 

Last Answer : What will happen if the primary of a transformer is connected to D.C. supply?  (A) Transformer will operate with low efficiency (B) Transformer will operate with high efficiency (C) No effect (D) Transformer may start to smoke and burn 

A certain transformer has 200 turns in the primary winding, 50 turns in the secondary winding and 120 volts

Description : A certain transformer has 200 turns in the primary winding, 50 turns in the secondary winding and 120 volts applied to the primary. What is the voltage across the secondary?  (A) 30 Volts (B) 480 Volts (C) 120 Volts (D) 60 Volts

Last Answer : A certain transformer has 200 turns in the primary winding, 50 turns in the secondary winding and 120 volts applied to the primary. What is the voltage across the secondary?  (A) 30 Volts (B) 480 Volts (C) 120 Volts (D) 60 Volts

A 230 V/460 V single-phase transformer operating at 20 A and unity power factor has primary referred

Description : A 230 V/460 V single-phase transformer operating at 20 A and unity power factor has primary referred resistance of 0.2 Ω and reactance of 0.5 Ω. The approximate primary induced emf is (A) 216 V (B) 226 V (C) 234 V (D) 236 V

Last Answer : A 230 V/460 V single-phase transformer operating at 20 A and unity power factor has primary referred resistance of 0.2 Ω and reactance of 0.5 Ω. The approximate primary induced emf is 226 V

The primary turns of a 444 V/222 V, 50 Hz single-phase transformer with a core cross- sectional area of...

Description : The primary turns of a 444 V/222 V, 50 Hz single-phase transformer with a core cross-sectional area of 100 cm2, and a maximum flux density of 1.0 T is (A) 100 (B) 200 (C) 222 (D) 400

Last Answer : The primary turns of a 444 V/222 V, 50 Hz single-phase transformer with a core cross-sectional area of 100 cm2, and a maximum flux density of 1.0 T is 200

A 1:5 step-up transformer has 120V across the primary and 600 ohms resistance across the secondary....

Description : A 1:5 step-up transformer has 120V across the primary and 600 ohms resistance across the secondary. Assuming 100% efficiency, the primary current will be:  (A) 0.2 Amp. (B) 5 Amps. (C)10 Amps. (D) 20 Amps

Last Answer : C. 10A

The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary ...

Description : The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be; (A) 3.6 (B) 2.5 V (C) 3.0 V (D) 6.0 V

Last Answer : The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be: 3.0 V

If a transformer primary is energised from a square wave voltage source, its output voltage will be a: ...

Description : If a transformer primary is energised from a square wave voltage source, its output voltage will be a:  (A) square wave (B) sine wave (C) triangular wave (D) pulse wave

Last Answer : D

A large transformer operating at no load draws an exciting current Io of 5A, when the primary is connected to...

Description : A large transformer operating at no load draws an exciting current Io of 5A, when the primary is connected to a 120 V, 60 Hz source. From a wattmeter test, it is known that iron losses are equal to 180 W. Calculate ... power absorbed by the core.  (A) 600 var (B) 572 var (C) 180 var (D) 360 var 

Last Answer : 572var

if the rated voltage from the power lines is applied to the primary of a single-phase transformer...

Description : if the rated voltage from the power lines is applied to the primary of a single-phase transformer which is operated on no-load, then

Last Answer : if the rated voltage from the power lines is applied to the primary of a single-phase transformer which is operated on no-load, then input voltage is sinusoidal and input current is non sinusoidal.

For a 100% efficient transformer, the primary winding has 1000 turns ...

Description : For a 100% efficient transformer, the primary winding has 1000 turns and the secondary 100 turns. If the power input to the above transformer is 1000 watts, the power output is_________.

Last Answer : For a 100% efficient transformer, the primary winding has 1000 turns and the secondary 100 turns. If the power input to the above transformer is 1000 watts, the power output is 1000 watts.

A 5 m ladder of mass 25 kg is placed in a position where its inclination to a vertical wall is at 30?. A 100 kg man is to climb the ladder. If the coefficient of static friction is 0.25 the height along ladder at which the slipping will be induced would be a.2.4 m b.1.6 m c.0.8 m d.1.2 m e.0.5 m

Description : A 5 m ladder of mass 25 kg is placed in a position where its inclination to a vertical wall is at 30?. A 100 kg man is to climb the ladder. If the coefficient of static friction is 0.25 the height along ladder at which the slipping will be induced would be a.2.4 m b.1.6 m c.0.8 m d.1.2 m e.0.5 m

Last Answer : c. 0.8 m

Why do we use O/C & E/F protection on both sides of transformer?

Description : Why do we use O/C & E/F protection on both sides of transformer?

Last Answer : Power in feed exists on both ends.  

Define the following terms as referred to battery. a) E.M.F b) Internal resistance c) Ah efficiency d) WAh efficiency

Description : Define the following terms as referred to battery. a) E.M.F b) Internal resistance c) Ah efficiency d) WAh efficiency

Last Answer : a) E.M.F : The electromotive force of a battery is defined as the energy spent or the work done in taking a unit positive charge around the complete circuit of the battery i.e., in ... input required to restore the initial state of charge, under specified conditions, is called Watt-hr efficiency.

Five cells, each with an e.m.f. of 2V and internal resistance of 0.5Ω are connected in series.

Description : Five cells, each with an e.m.f. of 2V and internal resistance of 0.5Ω are connected in series. The resulting battery will have

Last Answer : Five cells, each with an e.m.f. of 2V and internal resistance of 0.5Ω are connected in series. The resulting battery will have An e.m.f. of 10V and an internal resistance of 2.5 Ω

The back e.m.f of a motor at the moment of starting : -

Description : The back e.m.f of a motor at the moment of starting : -  a) zero b) maximum c) minimum d) optimum

Last Answer : The back e.m.f of a motor at the moment of starting : - zero

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed

Last Answer : b) 51.6N/mm2

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Last Answer : b) 25.8N/mm2

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Last Answer : b) 25.8N/mm2

In the illustrated 450 VAC system, what should be provided between the bus and the device labeled 'F'? EL-0003 A. a potential transformer B. a current transformer C. an emergency disconnect device D. an audible alarm and indicating light

Description : In the illustrated 450 VAC system, what should be provided between the bus and the device labeled 'F'? EL-0003 A. a potential transformer B. a current transformer C. an emergency disconnect device D. an audible alarm and indicating light

Last Answer : Answer: A