A feeder, in a transmission system, feeds power to
(a) distributors
(b) generating stations
(c) service mains
(d) all of the above

1 Answer

Answer :

(a) distributors

Related questions

Description : are the conductors, which connect the consumer's terminals to the distribution (a) Distributors (b) Service mains (c) Feeders (d) None of the above

Last Answer : (b) Service mains

Description : Transmitted power remaining the same, if supply voltage of a D.C. 2-wire feeder is increased 100 percent, saving in copper is (a) 25 percent (b) 50 percent (c) 75 percent (d) 100 percent

Last Answer : (b) 50 percent

Description : The loads on distributors systems are generally (a) balanced (b) unbalanced (c) either of the above (d) none of the above

Last Answer : (b) unbalanced

Description : The distributors for residential areas are (a) single phase (b) three-phase three wire (c) three-phase four wire (d) none of the above

Last Answer : (c) three-phase four wire

Description : Which of the following equipment, for regulating the voltage in distribution feeder, will be most economical ? (a) Static condenser (b) Synchronous condenser (c) Tap changing transformer (d) Booster transformer

Last Answer : (d) Booster transformer

Description : Which of the following is usually not the generating voltage ? (a) 6.6 kV (b) 8.8 kV (c) 11 kV (d) 13.2 kV

Last Answer : (b) 8.8 kV

Description : When the interconnector between two stations has large reactance (a) the transfer of power will take place with voltage fluctuation and noise (b) the transfer of power will take place with least loss ... out of step be¬cause of large angular displacement between the stations (d) none of the above

Last Answer : (c) the stations will fall out of step be¬cause of large angular displacement between the stations

Description : The angular displacement between two interconnected stations is mainly due to (a) armature reactance of both alternators (b) reactance of the interconnector (c) synchronous reactance of both the alternators (d) all of the above

Last Answer : (a) armature reactance of both alternators

Description : Constant voltage transmission entails the following disadvantage (a) large conductor area is required for same power transmission (b) short-circuit current of the system is increased (c) either of the above (d) none of the above

Last Answer : (b) short-circuit current of the system is increased

Description : Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at ... of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Last Answer : (a) Increase of short-circuit current of the system

Description : What are the factors that limit the maximum power transfer capability in a transmission line?

Last Answer : Answer: Some of the factors which limits the maximum power transfer are: 1. Electrical phase shift 2. Voltage drop 3. Thermal effects in the line

Description : For transmission of power over a distance of 500 km, the transmission voltage should be in the range (a) 150 to 220 kV (b) 100 to 120 kV (c) 60 to 100 kV (d) 20 to 50 kV

Last Answer : (a) 150 to 220 kV

Description : For transmission of power over a distance of 200 km, the transmission voltage should be (a) 132 kV (b) 66 kV (c) 33 kV (d) 11 kV

Last Answer : (a) 132 kV

Description : Which of the following materials is not used for transmission and distribution of electrical power ? (a) Copper (b) Aluminium (c) Steel (d) Tungsten

Last Answer : (d) Tungsten

Description : Explain some of the methods to improve the strength of transmission system?

Last Answer :  Introducing or adding of new transmission lines in to the system to avoid the overloading of the existing lines  Application of devices such as series capacitors in the right location of ... system  Adoption of multi-voltage levels an multi-circuits in the existing ac transmission system

Description : A 3-phase 4 wire system is commonly used on (a) primary transmission (b) secondary transmission (c) primary distribution (d) secondary distribution

Last Answer : (d) secondary distribution

Description : What are the problems associated with EHV transmission?

Last Answer : Answer: The problems associated with EHV transmission are corona loss and radio interference, requirement of heavy supporting structures and insulation requirments

Description : What is the material used for overhead transmission lines?

Last Answer : Answer: ACSR conductors are employed.

Description : What for series and shunt compensation provided in EHV transmission lines?

Last Answer : Answer: Series capacitance is provided in EHV lines to artificially reduce the series reactance of the line so as to improve stability, voltage regulation and transmission efficiency Shunt compensation ... reduce the line susceptance so as to improve the voltage regulation under light load condition

Description : Series capacitors on transmission lines are of little use when the load VAR requirement is (a) large (b) small (b) fluctuating (d) any of the above

Last Answer : (b) small

Description : In the analysis of which of the following lines shunt capacitance is neglected ? (a) Short transmission lines (b) Medium transmission lines (c) Long transmission lines (d) Medium as well as long transmission lines

Last Answer : (a) Short transmission lines

Description : The voltage drop, for constant voltage transmission is compensated by installing (a) inductors (b) capacitors (c) synchronous motors (d) all of above (e) none of the above

Last Answer : (c) synchronous motors

Description : Transmission voltage of ll kV is normally used for distances upto (a) 20—25 km (b) 40—50 km (c) 60—70 km (d) 80—100 km

Last Answer : (a) 20—25 km

Description : Which of the following characteristics should the line supports for transmission lines possess ? (a) Low cost (b) High mechanical strength (c) Longer life (d) All of the above

Last Answer : (d) All of the above

Description : Which of the following relays is used on long transmission lines ? (a) Impedance relay (b) Mho's relay (c) Reactance relay (d) None of the above

Last Answer : (b) Mho's relay

Description : Which of the following materials is used for overhead transmission lines ? (a) Steel cored aluminium (b) Galvanised steel (c) Cadmium copper (d) Any of the above

Last Answer : (d) Any of the above

Description : Transmission line insulators are made of (a) glass (b) porcelain (c) iron (d) P.V.C.

Last Answer : B

Description : In transmission lines the cross-arms are made of (a) copper (b) wood (c) R.C.C. (d) steel

Last Answer : (d) steel

Description : High voltage transmission lines use (a) suspension insulators (b) pin insulators (c) both (a) and (b) (d) none of the above

Last Answer : (a) suspension insulators

Description : Most of the high voltage transmission lines in India are (a) underground (b) overhead (c) either of the above (d) none of the above

Last Answer : (b) overhead

Description : Which of the following are the constants of the transmission lines ? (a) Resistance (b) Inductance (c) Capacitance (d) All of the above

Last Answer : (d) All of the above

Description : By which of the following systems electric power may be transmitted ? (a) Overhead system (b) Underground system (c) Both (a) and (b) (d) None of the above

Last Answer : (c) Both (a) and (b)

Description : The power transmitted will be maximum when (a) corona losses are minimum (b) reactance is high (c) sending end voltage is more (d) receiving end voltage is more

Last Answer : (c) sending end voltage is more

Description : The presence of ozone due to corona is harmful because it (a) reduces power factor (b) corrodes the material (c) gives odour (d) transfer energy to the ground (e) none of the above

Last Answer : (b) corrodes the material

Description : The power factor of industrial loads is generally (a) unity (b) lagging (c) leading (d) zero

Last Answer : (b) lagging

Description : Which of the following distribution systems is more reliable ? (a) Radial system (b) Tree system (c) Ring main system (d) All are equally reliable

Last Answer : (c) Ring main system

Description : Which of the following D.C. distribution system is the simplest and lowest in first cost ? (a) Radial system (b) Ring system (c) Inter-connected system (d) None of the above

Last Answer : (a) Radial system

Description : Overhead system can be designed for operation up to (a) 11 kV (b) 33 kV (c) 66 kV (d) 400 kV

Last Answer : (c) 66 kV

Description : The underground system cannot be operated above (a) 440 V (b) 11 kV (c) 33 kV (d) 66 kV

Last Answer : (d) 66 kV

Description : Why does surge impedance loading (SIL) increase with increase in voltage level?

Last Answer : Answer: SIL varies as the square of the operating voltage, so SIL increases with increase in voltage level

Description : Electro-mechanical voltage regulators are generally used in (a) reactors (b) generators (c) transformers (d) all of the above

Last Answer : (b) generators

Description : When an alternator connected to the bus-bar is shut down the bus-bar voltage will (a) fall (b) rise (c) remain unchanged (d) none of the above

Last Answer : (c) remain unchanged

Description : The frequency of voltage generated, in case of generators, can be increased by (a) using reactors (b) increasing the load (c) adjusting the governor (d) reducing the terminal voltage (e) none of the above

Last Answer : (c) adjusting the governor

Description : The effect of corona can be detected by (a) presence of ozone detected by odour (b) hissing sound (c) faint luminous glow of bluish colour (d) all of the above

Last Answer : (d) all of the above

Description : In a tap changing transformer, the tappings are provided on (a) primary winding (b) secondary winding (c) high voltage winding (d) any of the above

Last Answer : (b) secondary winding

Description : For aluminium, as compared to copper, all the following factors have higher values except (a) specific volume (6) electrical conductivity (c) co-efficient of linear expansion (d) resistance per unit length for same cross-section

Last Answer : (6) electrical conductivity

Description : Aluminium has a specific gravity of (a) 1.5 (b) 2.7 (c) 4.2 (d) 7.8

Last Answer : (b) 2.7

Description : Pin type insulators are generally not used for voltages beyond (a) 1 kV (b) 11 kV (c) 22 kV (d) 33 kV

Last Answer : (d) 33 kV

Description : The current drawn by the line due to corona losses is (a) non-sinusoidal (b) sinusoidal (c) triangular (d) square

Last Answer : (a) non-sinusoidal

Description : The use of strain type insulators is made where the conductors are (a) dead ended (b) at intermediate anchor towers (c) any of the above (d) none of the above

Last Answer : (c) any of the above