An Oil-filled cable has a working stress of ___________ kV/mm. 

(A) 10 (B) 12 (C) 13 (D) 15

1 Answer

Answer :

Answer : (D) 15

Related questions

Description : Oil-filled cable has a working stress of __________ kV/mm (A) 10 (B) 12 (C) 13 (D) 15

Last Answer : Ans: D This is defined by dielectric strength of mineral oil i.e. 15 kV/mm.

Description : If a cable of homogeneous insulation has a maximum stress of 10 kV/mm, then the dielectric strength of insulation should be (a) 5 kV/mm (b) 10 kV/mm (a) 15 kV/mm (d) 30 kV/mm

Last Answer : (b) 10 kV/mm

Description : Cables, generally used beyond 66 kV are (a) oil filled (b) S.L. type (c) belted (d) armoured

Last Answer : (a) oil filled

Description : For LV applications (below 1 kV), ______________ cables are used. (A) Paper insulated. (B) Plastic. (C) Single core cables. (D) Oil filled.

Last Answer : Ans: C For low voltage applications single core cables are suitable.

Description : A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum permissible stress in the dielectric is not to exceed 20 kV/mm. For economical size, the overall core diameter of the cable is (A) 28.2 mm (B) 26.4 mm (C) 24.4 mm (D) 22.0 mm

Last Answer : A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum permissible stress in the dielectric is not to exceed 20 kV/mm. For economical size, the overall core diameter of the cable is 22.0 mm

Description : A dash pot consists of a cylinder 10 cm in diameter in which slides a piston 12 cm long having a radial clearance of 1 mm. The cylinder is filled with oil having a viscosity of 1 poise. What will be the resistance offered ... with a velocity of 3 cm/sec a.1090 kg b.100 kg c.10900 kg d.10 kg e.50 kg

Last Answer : c. 10900 kg

Description : Dielectric strength of rubber is around (a) 5 kV/mm (b) 15 kV/mm (c) 30 kV/mm (d) 200 kV/mm

Last Answer : (c) 30 kV/mm

Description : A practical formula for determining the thickness of insulation between low voltage and high voltage windings is (a) 1 + 0.2 kVmm (6) 2 + 0.5 kVmm (c) 4 + 0.7 kV mm (d) 5 + 0.9 kV mm

Last Answer : (d) 5 + 0.9 kV mm

Description : Is a cable is to be designed for use on 1000 kV, which insulation would you prefer ? (a) Polyvinyle chloride (b) Vulcanised rubber (c) Impregnated paper (d) Compressed SFe gas (e) none of the above

Last Answer : (d) Compressed SFe gas

Description : If the width of a pavement slab is 7.5 m, thickness 20 cm and working stress 1400 kg/cm2 , spacing of 10 mm tie bars for the longitudinal joint, is (A) 10 cm (B) 20 cm (C) 30 cm (D) 40 cm

Last Answer : Answer: Option C

Description : As per chart on energy consumption the supply unit of furnace oil is ……… a. kWh c. kV b. kg. d. Watts

Last Answer : kg

Description : 99. As per chart on energy consumption the supply unit of furnace oil is ……… a. kWh c. kV b. kg. d. Watts

Last Answer : kg.

Description : Cables for 220 kV lines are invariably (a) mica insulated (b) paper insulated (c) compressed oil or compressed gas insulated (d) rubber insulated (e) none of the above

Last Answer : (c) compressed oil or compressed gas insulated

Description : 63 The dielectric strength of transformer oil is expected to be A. 1kV B. 33kV C. 100kV D. 330 kV

Last Answer : B. 33kv

Description : The dielectric strength of transformer oil should be (A) 100 V. (B) 5 KV. (C) 30 KV. (D) 132 KV.

Last Answer : (C) 30 KV.

Description : A three-phase, 33 kV oil circuit breaker is rated 1200 A, 2000 MVA, 3 s. The symmetrical breaking current is  (A) 1200 A (B) 3600 A (C) 35 kA (D) 104.8 kA

Last Answer : A three-phase, 33 kV oil circuit breaker is rated 1200 A, 2000 MVA, 3 s. The symmetrical breaking current is 35 kA 

Description : ECE Board Exam March 1996 Crosstalk coupling is ___________. A. dBm (disturbing pair) minus dBm (disturbed pair) B. the difference between readings on a cable pair with a tone and a cable pair without ... a cable C. signals from one circuit that get into another circuit D. All of these are true

Last Answer : D. All of these are true

Description : 802.3 is the standard for 10BASE5 Ethernet that uses ___________ cable as shared medium. A. Twisted pair cable B. Coaxial cable C. Fiber optic cable D. None of the above 

Last Answer : B. Coaxial cable 

Description : A 3-phase star-connected 75 MVA, 25 kV 3-phase synchronous generator has a synchronous reactance of 1.0 p.u. The per unit value to a 90 MVA base and 30 kV is (A) 2/15 p.u. (B) 5/6 p.u. (C) 1.0 p.u. (D) 1.2 p.u.

Last Answer : A 3-phase star-connected 75 MVA, 25 kV 3-phase synchronous generator has a synchronous reactance of 1.0 p.u. The per unit value to a 90 MVA base and 30 kV is 5/6 p.u.

Description : The corona loss of a 3-phase transmission line is 100 kW at 60 kV/phase and 25 kW at 50 kV/phase. The disruptive critical voltage is (A) 40 kV (B) 43.6 kV (C) 49.6 kV (D) 50 kV

Last Answer : The corona loss of a 3-phase transmission line is 100 kW at 60 kV/phase and 25 kW at 50 kV/phase. The disruptive critical voltage is 40 kV

Description : A 1100 kVA, 11 kV/1.1 kV conventional two-winding transformer is connected as a 12.1 kV/11 kV step-down auto-transformer. The rating of the auto-transformer is (A) 1000 kVA (B) 1100 kVA (C) 11000 kVA (D) 12100 kVA

Last Answer : A 1100 kVA, 11 kV/1.1 kV conventional two-winding transformer is connected as a 12.1 kV/11 kV step-down auto-transformer. The rating of the auto-transformer is 12100 kVA

Description : In a certain three -wire Y -connected generator, the phase voltages are 2 kV. The magnitudes of the line voltages will be: A. 2,000 V B. 6,000 V C. 666 V D. 3,464 V

Last Answer : In a certain three -wire Y -connected generator, the phase voltages are 2 kV. The magnitudes of the line voltages will be: 3,464 V

Description : A 3-phase circuit breaker is rated at 1250 A, 2000 MVA, 33 kV, 4s. Its making current capacity will be   (a) 35 kA (b) 89 kA (c) 79 kA (d) 69 kA

Last Answer : 89

Description : The per unit impedance of a circuit element is 0.30. If the base kV and base MVA are halved, then the new value of the per unit impedance of the circuit element will be:  (A) 0.3 (B) 0.6 (C) 0.003 (D) 0.006 

Last Answer : 3

Description : A single phase transformer rated at 3000 kVA, 69 kV 4.16 kV, 60 Hz has a total internal impedance Zp of 127 ohm, referred to the primary side. Calculate the primary current if the secondary is accidentally short circuited.  (A) 43.5 A (B) 543 A (C) 9006 A (D) 721 A 

Last Answer : 543A

Description : A 60 Hz, 4 pole turbo generator rated 100 MVA, 13.8 KV has an inertia constant of 10 MJ/MVA. Find the stored energy in the rotor at synchronous speed.  (A) 10 MJ (B) 100 J (C) 1000 J (D) 1000 MJ 

Last Answer : c

Description : how can we express 0.40 kV in volts?

Last Answer : Kvx1000=400v

Description : Earthquakes that occur along faults are created when ___________ a) Melted rock is erupted along the fault zone b) Stress builds up until rocks break c) The earth shifts and moves along fracture d) Answers b and c

Last Answer : d) Answers b and c

Description : What are the safety features of oil filled transformers?

Last Answer : Environmental safety in case of spillage.There has to be a dyke wall for oil containment in case of spillage so that the oil does not get into ground / land.Oil level must be ... tested and minimum value must be maintained.Oil Cooling arrangement must be maintained.No leakage in radiators.

Description : Figure 'B' shown in the illustration represents a/an ____________. EL-0091 A. magnetic amplifier B. Scott-T transformer C. saturable-core reactor D. oil-filled toroid

Last Answer : Answer: A

Description : Figure 'A' shown in the illustration represents a/an _______________. EL-0091 A. magnetic amplifier B. Scott-T transformer C. saturable-core reactor D. oil-filled toroid

Last Answer : Answer: C

Description : 07. A closed tank is completely filled with an oil. If it is made to move with a horizontal acceleration, then the pressure at the back end will be more than that at the front end. A) Correct B) Incorrect

Last Answer : A

Description : It is difficult to maintain oil filled cables. (a) Yes (b) No

Last Answer : (a) Yes

Description : The advantage of oil filled cables is (a) more perfect impregnation (b) smaller overall size (c) no ionisation, oxidation and formation of voids (d) all of the above

Last Answer : (d) all of the above

Description : In an oil filled transformer, oil is provided for (A) cooling (B) insulation (C) lubrication (D) both (A) and (B)

Last Answer : In an oil filled transformer, oil is provided for (A) cooling (B) insulation (C) lubrication (D) both (A) and (B)

Description : Under normal operating conditions, the bearings are filled with the proper type of lubricant after every hours of working about a) 6 hours b) 8 hoursc) 10 hours d) 12 hours

Last Answer : c) 10 hours

Description : When asked about the quality of Electrico's distribution system, Mark Johnson proclaims that 95 percent of all orders are filled within two working days. This statement represents the firm's A)mission statement. B)response factor. C)shipping objective. D)customer commitment. E)service standard.

Last Answer : E)service standard.

Description : Is it possible to have a baby after eating MM kit ? After 1 day of eating MM kit, bleeding stopped and there was excess pain in the lower abdomen. I took painkillers and the pain did not subside ... Kit cause any problem for mother and baby. Please give me the correct answer I am under extra stress.

Last Answer : Usually when the fetal age is maximum 9 weeks or 63 days, it can be destroyed by using MM kit. But if it is more than that, abortion can no longer be done with MM kit It may be more or less , ... will not be harmed. There will be no problem in having a baby in the future or in the present baby.

Description : A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a  load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending  strain energy stored in the ... (A) 411 N mm  (B) 511 N mm  (C) 611 N mm  (D) 711 N mm 

Last Answer : (C) 611 N mm 

Description : A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so  that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the  value of E = 0.2 ... joist, is  (A) 200 mm  (B) 250 mm  (C) 300 mm  (D) 400 mm 

Last Answer : (D) 400 mm 

Description : If a concrete column 200 200 mm in cross-section is reinforced with four steel bars of 1200  mm2  total cross-sectional area. Calculate the safe load for the column if permissible stress in  concrete is 5 N/mm2 ... 15 Ec (A) 264 MN  (B) 274 MN  (C) 284 MN  (D) 294 MN 

Last Answer : (C) 284 MN 

Description : A load of 1960 N is raised at the end of a steel wire. The minimum diameter of the wire so that  stress in the wire does not exceed 100 N/mm2  is:  (A) 4.0 mm  (B) 4.5 mm  (C) 5.0 mm  (D) 5.5 mm

Last Answer : (C) 5.0 mm 

Description : If a steel rod of 20 mm diameter and 5 metres long elongates by 2.275 mm when subjected to an  axial pull of 3000 kg, the stress developed, is  (A) 9.5541 kg/cm2 (B) 95.541 kg/cm2 (C) 955.41 kg/cm2 (D) 9554.1 kg/cm

Last Answer : (C) 955.41 kg/cm2

Description : If a steel rod of 20 mm diameter and 5 metres long elongates by 2.275 mm when subjected to an  axial pull of 3000 kg, the stress developed, is  (A) 9.5541 kg/cm2 (B) 95.541 kg/cm2 (C) 955.41 kg/cm2 (D) 9554.1 kg/cm

Last Answer : (C) 955.41 kg/cm2

Description : A normally consolidated clay settled 10 mm when effective stress was increased from 100 kN/m² to 200 kN/m². If the effective stress is further increased from 200 kN/m² to 400 kN/m², then the settlement of the same clay is (A) 10 mm (B) 20 mm (C) 40 mm (D) None of the above

Last Answer : (A) 10 mm

Description : An R.C.C. column of 30 cm diameter is reinforced with 6 bars 12 mm placed symmetrically along the circumference. If it carries a load of 40, 000 kg axially, the stress is (A) 49.9 kg/cm2 (B) 100 kg/cm2 (C) 250 kg/cm2 (D) 175 kg/cm

Last Answer : Answer: Option A

Description : For an ordinary Portland cement (A) Residual does not exceed 10% when sieved through IS Sieve No. 9 (B) Soundness varies from 5 to 10 mm (C) Initial setting time is not less than 30 minutes (D) Compressive stress after 7 days, is not less than 175 kg/cm2

Last Answer : (C) Initial setting time is not less than 30 minutes

Description : Generally the strength of concrete is represented by the crushing stress of concrete cube of size [ A ] 50 mm [ B ] 100 mm [ C ] 150 mm [ D ] 250 mm

Last Answer : [ C ] 150 mm

Description : Compute the maximum shearing stress developed in a phosphor bronze spring having mean diameter of 200 mm and consisting of 24 turns of 20-mm diameter wire when the spring is stretched 100 mm. and G = 42 GPa. a. 51 MPa b. 31.89 MPa c. 80 MPa d. 70 MPa

Last Answer : b. 31.89 MPa