The voltage drop, for constant voltage transmission is compensated by installing
(a) inductors
(b) capacitors
(c) synchronous motors
(d) all of above
(e) none of the above

1 Answer

Answer :

(c) synchronous motors

Related questions

Description : Series capacitors on transmission lines are of little use when the load VAR requirement is (a) large (b) small (b) fluctuating (d) any of the above

Last Answer : (b) small

Description : Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at ... of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Last Answer : (a) Increase of short-circuit current of the system

Description : Constant voltage transmission entails the following disadvantage (a) large conductor area is required for same power transmission (b) short-circuit current of the system is increased (c) either of the above (d) none of the above

Last Answer : (b) short-circuit current of the system is increased

Description : Which of the following equipment, for regulating the voltage in distribution feeder, will be most economical ? (a) Static condenser (b) Synchronous condenser (c) Tap changing transformer (d) Booster transformer

Last Answer : (d) Booster transformer

Description : In a substation the following equipment is not installed (a) exciters (b) series capacitors (c) shunt reactors (d) voltatre transformers

Last Answer : (a) exciters

Description : For transmission of power over a distance of 500 km, the transmission voltage should be in the range (a) 150 to 220 kV (b) 100 to 120 kV (c) 60 to 100 kV (d) 20 to 50 kV

Last Answer : (a) 150 to 220 kV

Description : For transmission of power over a distance of 200 km, the transmission voltage should be (a) 132 kV (b) 66 kV (c) 33 kV (d) 11 kV

Last Answer : (a) 132 kV

Description : Transmission voltage of ll kV is normally used for distances upto (a) 20—25 km (b) 40—50 km (c) 60—70 km (d) 80—100 km

Last Answer : (a) 20—25 km

Description : High voltage transmission lines use (a) suspension insulators (b) pin insulators (c) both (a) and (b) (d) none of the above

Last Answer : (a) suspension insulators

Description : Most of the high voltage transmission lines in India are (a) underground (b) overhead (c) either of the above (d) none of the above

Last Answer : (b) overhead

Description : In a D.C. 3-wire distributor using balancers and having unequal loads on the two sides (a) both balancers run as generators (b) both balancers run as motors (c) balancer connected to lightly- loaded side runs as a motor (d) balancer connected to heavily- loaded side runs as a motor

Last Answer : (c) balancer connected to lightly- loaded side runs as a motor

Description : The angular displacement between two interconnected stations is mainly due to (a) armature reactance of both alternators (b) reactance of the interconnector (c) synchronous reactance of both the alternators (d) all of the above

Last Answer : (a) armature reactance of both alternators

Description : A booster is a (a) series wound generator (b) shunt wound generator (c) synchronous generator (d) none of the above

Last Answer : (a) series wound generator

Description : A uniformly-loaded D.C. distributor is fed at both ends with equal voltages. As compared to a similar distributor fed at one end only, the drop at the middle point is (a) one-fourth (b) one-third (c) one-half (d) twice (e) none of the above

Last Answer : (a) one-fourth

Description : Explain some of the methods to improve the strength of transmission system?

Last Answer :  Introducing or adding of new transmission lines in to the system to avoid the overloading of the existing lines  Application of devices such as series capacitors in the right location of ... system  Adoption of multi-voltage levels an multi-circuits in the existing ac transmission system

Description : What are the factors that limit the maximum power transfer capability in a transmission line?

Last Answer : Answer: Some of the factors which limits the maximum power transfer are: 1. Electrical phase shift 2. Voltage drop 3. Thermal effects in the line

Description : What are the problems associated with EHV transmission?

Last Answer : Answer: The problems associated with EHV transmission are corona loss and radio interference, requirement of heavy supporting structures and insulation requirments

Description : What is the material used for overhead transmission lines?

Last Answer : Answer: ACSR conductors are employed.

Description : What for series and shunt compensation provided in EHV transmission lines?

Last Answer : Answer: Series capacitance is provided in EHV lines to artificially reduce the series reactance of the line so as to improve stability, voltage regulation and transmission efficiency Shunt compensation ... reduce the line susceptance so as to improve the voltage regulation under light load condition

Description : In the analysis of which of the following lines shunt capacitance is neglected ? (a) Short transmission lines (b) Medium transmission lines (c) Long transmission lines (d) Medium as well as long transmission lines

Last Answer : (a) Short transmission lines

Description : Which of the following characteristics should the line supports for transmission lines possess ? (a) Low cost (b) High mechanical strength (c) Longer life (d) All of the above

Last Answer : (d) All of the above

Description : Which of the following relays is used on long transmission lines ? (a) Impedance relay (b) Mho's relay (c) Reactance relay (d) None of the above

Last Answer : (b) Mho's relay

Description : Which of the following materials is used for overhead transmission lines ? (a) Steel cored aluminium (b) Galvanised steel (c) Cadmium copper (d) Any of the above

Last Answer : (d) Any of the above

Description : A 3-phase 4 wire system is commonly used on (a) primary transmission (b) secondary transmission (c) primary distribution (d) secondary distribution

Last Answer : (d) secondary distribution

Description : A feeder, in a transmission system, feeds power to (a) distributors (b) generating stations (c) service mains (d) all of the above

Last Answer : (a) distributors

Description : Transmission line insulators are made of (a) glass (b) porcelain (c) iron (d) P.V.C.

Last Answer : B

Description : In transmission lines the cross-arms are made of (a) copper (b) wood (c) R.C.C. (d) steel

Last Answer : (d) steel

Description : Which of the following are the constants of the transmission lines ? (a) Resistance (b) Inductance (c) Capacitance (d) All of the above

Last Answer : (d) All of the above

Description : Which of the following materials is not used for transmission and distribution of electrical power ? (a) Copper (b) Aluminium (c) Steel (d) Tungsten

Last Answer : (d) Tungsten

Description : The frequency of voltage generated, in case of generators, can be increased by (a) using reactors (b) increasing the load (c) adjusting the governor (d) reducing the terminal voltage (e) none of the above

Last Answer : (c) adjusting the governor

Description : Why does surge impedance loading (SIL) increase with increase in voltage level?

Last Answer : Answer: SIL varies as the square of the operating voltage, so SIL increases with increase in voltage level

Description : Electro-mechanical voltage regulators are generally used in (a) reactors (b) generators (c) transformers (d) all of the above

Last Answer : (b) generators

Description : When an alternator connected to the bus-bar is shut down the bus-bar voltage will (a) fall (b) rise (c) remain unchanged (d) none of the above

Last Answer : (c) remain unchanged

Description : When the interconnector between two stations has large reactance (a) the transfer of power will take place with voltage fluctuation and noise (b) the transfer of power will take place with least loss ... out of step be¬cause of large angular displacement between the stations (d) none of the above

Last Answer : (c) the stations will fall out of step be¬cause of large angular displacement between the stations

Description : In a tap changing transformer, the tappings are provided on (a) primary winding (b) secondary winding (c) high voltage winding (d) any of the above

Last Answer : (b) secondary winding

Description : By which of the following a bus-bar is rated ? (a) Current only (b) Current and voltage (c) Current, voltage and frequency (d) Current, voltage, frequency and short time current

Last Answer : (d) Current, voltage, frequency and short time current

Description : The power transmitted will be maximum when (a) corona losses are minimum (b) reactance is high (c) sending end voltage is more (d) receiving end voltage is more

Last Answer : (c) sending end voltage is more

Description : Which of the following is usually not the generating voltage ? (a) 6.6 kV (b) 8.8 kV (c) 11 kV (d) 13.2 kV

Last Answer : (b) 8.8 kV

Description : As compared to a 2-wire D.C. distributor, a 3-wire distributor with same maximum voltage to earth uses only (a) 31.25 percent of copper (b) 33.3 percent of copper (c) 66.7 percent of copper (d) 125 percent of copper

Last Answer : (a) 31.25 percent of copper

Description : Transmitted power remaining the same, if supply voltage of a D.C. 2-wire feeder is increased 100 percent, saving in copper is (a) 25 percent (b) 50 percent (c) 75 percent (d) 100 percent

Last Answer : (b) 50 percent

Description : The material generally used for armour of high voltage cables is (a) aluminium (b) steel (c) brass (d) copper

Last Answer : (b) steel

Description : The material commonly used for insulation in high voltage cables is (a) lead (b) paper (c) rubber (d) none of the above

Last Answer : (b) paper

Description : The voltage of the single phase supply to residential consumers is (a) 110 V (b) 210 V (c) 230 V (d) 400 V

Last Answer : (c) 230 V

Description : The phenomenon qf rise in voltage at the receiving end of the open-circuited or lightly loaded line is called the (a) Seeback effect (b) Ferranti effect (c) Raman effect (d) none of the above

Last Answer : (b) Ferranti effect

Description : By which of the following methods string efficiency can be improved ? (a) Using a guard ring (b) Grading the insulator (c) Using long cross arm (d) Any of the above (e) None of the above

Last Answer : (d) Any of the above

Description : Owing to skin effect (a) current flows through the half cross-section of the conductor (b) portion of the conductor near the surface carries more current and core of the conductor carries less current (c) ... core of the conductor carries more cur¬rent (d) any of the above (e) none of the above

Last Answer : (b) portion of the conductor near the surface carries more current and core of the conductor carries less current

Description : The steel used in steel cored conductors is usually (a) alloy steel (b) stainless steel (c) mild steel (d) high speed steel (e) all of the above

Last Answer : (c) mild steel

Description : There is a greater possibility of occurence of corona during (a) dry weather (b) winter (c) summer heat (d) humid weather (e) none of the above

Last Answer : (d) humid weather

Description : The presence of ozone due to corona is harmful because it (a) reduces power factor (b) corrodes the material (c) gives odour (d) transfer energy to the ground (e) none of the above

Last Answer : (b) corrodes the material

Description : For an overhead line, the surge impedance is taken as (a) 20-30 ohms (b) 70—80 ohms (c) 100—200 ohms (d) 500—1000 ohms (e) none of the above

Last Answer : (c) 100—200 ohms