A separately excited dc motor is required to be controlled, from a 3-phase supply, for its operation in the first...

A separately excited dc motor is required to be controlled, from a 3-phase supply, for its operation in the first quadrant only. The most preferred converter would be 

(a) 3-phase fully controlled converter (b) 3-phase fully controlled converter with free wheel diode (c) 3-phase dual converter (d) 3-phase half wave converter 
by

1 Answer

Answer :

A
by

Related questions

A single-phase half-controlled rectifier is driving a separately excited dc motor. The dc motor has a back emf

Description : A single-phase half-controlled rectifier is driving a separately excited dc motor. The dc motor has a back emf constant of 0.5 V/rpm. The armature current is 5 A without any ripple. The armature resistance is 2 Ohm. The ... of the motor will be  (A) 339 rpm (B) 359 rpm (C) 366 rpm (D) 386 rpm

Last Answer : 359

A separately excited dc motor operating in first quadrant is fed from 3-phase semi -converter free -wheeling

Description : A separately excited dc motor operating in first quadrant is fed from 3-phase semi -converter free -wheeling diode is open circuited, then the motor :  (A) can be operated in first quadrant (B) ... in first & second quadrants (C) can be operated in first & fourth quadrants (D) cannot be operated

Last Answer : A separately excited dc motor operating in first quadrant is fed from 3-phase semi -converter free -wheeling diode is open circuited, then the motor : can be operated in first & fourth quadrants

A DC chopper is used for regenerative braking of a separately excited DC motor. The DC supply

Description : A DC chopper is used for regenerative braking of a separately excited DC motor. The DC supply voltage is 400V. The armature current during regenerative braking is kept constant at 300 A with negligible ripple. For a duty cycle of 60% ... to the DC supply is  (a) 78 kW (b) 58 kW (c) 38 kW (d) 48 kW

Last Answer : 48

The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a

Description : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ (A) directly proportional to α and Φ (B) ... proportional to α and inversely proportional to Φ (D) directly proportional to Φ and inversely proportional to α

Last Answer : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ directly proportional to α and inversely proportional to Φ

The supply both to field and armature circuits are disconnected simultaneously in a separately excited dc...

Description : The supply both to field and armature circuits are disconnected simultaneously in a separately excited dc motor and it comes to a standstill in 5 sec. If the armature circuit of this motor is disconnected from supply with field ... rest in (1) 5 sec (2) 7 sec (3) 4 sec (4) A very long time  

Last Answer : 5 sec only.standstill time doesn't depend upon field excitation

Separately Excited DC motor

Description : Separately Excited DC motor

Last Answer : Separately Excited DC motor

A separately excited d.c. motor fed from single phase full converter with firing angle 60° runs at 1000 r.p.m.

Description : A separately excited d.c. motor fed from single phase full converter with firing angle 60° runs at 1000 r.p.m. If motor is connected to single phase semiconverter with the same firing angle of 60°, it would run at (a) 2000 rpm (b) 1850 rpm (c) 1500 rpm (d) 1000 rpm 

Last Answer : Ans =1500

What is the difference between self-excited and separately excited DC generator?

Description : What is the difference between self-excited and separately excited DC generator? 

Last Answer : Self-excited generator: In a self-excited generator the field winding is excited by an external DC source like a battery etc. Separately excited generator: In a separately excited generator the field poles ... is again fed to the field winding and goes on till the generator builds up voltage. 

what is separately excited motor ?

Description : what is separately excited motor ?

Last Answer : the field winding have different source power supply and armature have different power supply source

A separately excited d.c. machine is coupled to a 50 Hz, three-phase, 4-pole induction machine as shown in

Description : A separately excited d.c. machine is coupled to a 50 Hz, three-phase, 4-pole induction machine as shown in the figure. The Dc machine is energized first and the machines rotate at 1 600 ... three phase source, the phase sequence being consistent with the direction of rotation. In steady state

Last Answer : A separately excited d.c. machine is coupled to a 50 Hz, three-phase, 4-pole induction machine as shown in the figure. The Dc machine is energized first and the machines rotate at 1 600 1pm. ... rotation. In steady state DC machine acts as a motor and the induction machine acts as a generator  

Which of the following statements represents an application of a silicon controlled rectifier? A. To provide DC power for a main propulsion motor. B. For use as a voltage reference diode. C. For sensing flame in an automated burner. D. To eliminate power supply hum.

Description : Which of the following statements represents an application of a silicon controlled rectifier? A. To provide DC power for a main propulsion motor. B. For use as a voltage reference diode. C. For sensing flame in an automated burner. D. To eliminate power supply hum.

Last Answer : Answer: A

What's is the self excited dc motor?

Last Answer : Self excited Dc motor have same source of power to armature and field winding

A three-phase, 440 V, 50 Hz ac mains fed thyristor bridge is feeding a 440 V dc, 15 kW, 1500 rpm separately

Description : A three-phase, 440 V, 50 Hz ac mains fed thyristor bridge is feeding a 440 V dc, 15 kW, 1500 rpm separately excited dc motor with a ripple free continuous current in the dc link under all operating conditions, Neglecting the ... at half the rated speed is  (A) 0.354 (B) 0.372 (C) 0.90 (D) 0.955

Last Answer : A three-phase, 440 V, 50 Hz ac mains fed thyristor bridge is feeding a 440 V dc, 15 kW, 1500 rpm separately excited dc motor with a ripple free continuous current in the dc link under all operating conditions, Neglecting the losses, the power factor of the ac mains at half the rated speed is 0.354

A large dc motor is required to control the speed of the blower from a 3 -phase ac source. The suitable ac to ...

Description : A large dc motor is required to control the speed of the blower from a 3 -phase ac source. The suitable ac to dc converter is, 3 -phase (a) Fully controlled bridge converter ( ... bridge converter with freewheeling diode (c) Half controlled bridge converter (d) Converter pair in sequence control

Last Answer : a fullu control

A separately excited generator as compared to a self-excited generator (a) is amenable to better voltage con-trol (b) is more stable (c) has exciting current independent of load current (d) has all above features

Description : A separately excited generator as compared to a self-excited generator (a) is amenable to better voltage con-trol (b) is more stable (c) has exciting current independent of load current (d) has all above features

Last Answer : Ans: d

In a separately excited generator supplying rated load the armature reaction?

Last Answer : In a separately excited generator supplying rated load the armature reaction is always present.

A separately excited generator as compared to a self-excited generator?

Last Answer : A separately excited generator as compared to a self-excited generator is amenable to better voltage control, more stable, has exciting current independent of load current.

On some diesel-electric ships, the DC propulsion motor will only attain half speed when the generator fields are fully excited. Speeds above this are obtained by _____________. A. rotating brush alignment B. raising the generator engine speed C. lowering the generator engine speed D. decreasing excitation

Description : On some diesel-electric ships, the DC propulsion motor will only attain half speed when the generator fields are fully excited. Speeds above this are obtained by _____________. A. rotating brush ... B. raising the generator engine speed C. lowering the generator engine speed D. decreasing excitation

Last Answer : Answer: B

What is the order of the characteristic equation of an armature controlled DC motor?

Description : What is the order of the characteristic equation of an armature controlled DC motor?  (A) First order equation (B) Second order equation (C) Zero order equation (D) Third order equation 

Last Answer : third order

State the principle of operation of a dc motor.

Last Answer : Principle of operation of a dc motor: When a current carrying conductor is placed in a magnetic field, the conductor experiences the mechanical force. The magnitude of force is given by  F = BIL newton  where F – Force , B – Maximum flux density , I – Current , L – Active length of conductor

An a.c. tachometer is just a ________with one phase excited from the carrier frequency. (A) two-phase A.C. servomotor (B) two-phase induction motor (C) A.C. operated universal motor (D) hybrid stepper motor.

Description : An a.c. tachometer is just a ________with one phase excited from the carrier frequency. (A) two-phase A.C. servomotor (B) two-phase induction motor (C) A.C. operated universal motor (D) hybrid stepper motor.

Last Answer : Ans: D This is a special purpose machine whose stator coil can be energized by electronically switched current.

A single-phase induction motor with only the main winding excited would exhibit the following response at

Description : A single-phase induction motor with only the main winding excited would exhibit the following response at synchronous speed  (A) Rotor current is zero (B) Rotor current is non-zero and is ... and backward rotating fields are equal (D) Forward rotating field is more than the backward rotating field

Last Answer : A single-phase induction motor with only the main winding excited would exhibit the following response at synchronous speed  (A) Rotor current is zero (B) Rotor current is non-zero and is ... backward rotating fields are equal (D) Forward rotating field is more than the backward rotating field

Chopper controlled DC motor

Description : Chopper controlled DC motor

Last Answer : Chopper controlled DC motor

In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage

Description : In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage

Last Answer : In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage decreases

A single-phase fully controlled thyristor bridge ac-dc converter is operating at a firing angle of 25 and an

Description : A single-phase fully controlled thyristor bridge ac-dc converter is operating at a firing angle of 25o and an overlap angle of 10o with constant dc output current of 20 A. The fundamental power factor (displacement factor) at input ac mains is  (A) 0.78 (B) 0.827 (C) 0.866 (D) 0.9

Last Answer : A single-phase fully controlled thyristor bridge ac-dc converter is operating at a firing angle of 25o and an overlap angle of 10o with constant dc output current of 20 A. The fundamental power factor (displacement factor) at input ac mains is 0.78

A 3 -phase, fully controlled, converter is feeding power into a DC load at a constant current of 150 A, the rms

Description : A 3 -phase, fully controlled, converter is feeding power into a DC load at a constant current of 150 A, the rms value of the current flowing through each thyristor of the converter is

Last Answer : Please show the solution for this question

A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc

Description : A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is (A) 4.5 V (B) 6.75 V (C) 9 V (D) 13.5 V

Last Answer : A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is 9 V

Give the operation of single phase full wave bridge controlled converter with RL load with a neat diagram. Also draw its waveform.

Description : Give the operation of single phase full wave bridge controlled converter with RL load with a neat diagram. Also draw its waveform.

Last Answer : Single phase fully control bridge converter with RL load: 1. During positive half cycle of input voltage, T1 and T2 are forward biased and during negative half cycle, T3 and T4 are forward biased. Therefore, T1-T2 ... cycle till the firing of next pair of SCRs as shown in the waveform.

The speed of a 4-pole induction motor is controlled by varying the supply frequency while maintaining the

Description : The speed of a 4-pole induction motor is controlled by varying the supply frequency while maintaining the ratio of supply voltage to supply frequency (V/f ) constant. At rated frequency of 50 Hz and rated voltage of 400 V ... load torque is constant  (A) 882 rpm (B) 864 rpm (C) 840 rpm (D) 828 rpm

Last Answer : The speed of a 4-pole induction motor is controlled by varying the supply frequency while maintaining the ratio of supply voltage to supply frequency (V/f ) constant. At rated frequency of 50 Hz and rated voltage of 400 ... torque is constant  (A) 882 rpm (B) 864 rpm (C) 840 rpm (D) 828 rpm

A solar cell of 350 V is feeding power to an ac supply of 440 V, 50 Hz through a 3-phase fully controlled bridge

Description : A solar cell of 350 V is feeding power to an ac supply of 440 V, 50 Hz through a 3-phase fully controlled bridge converter. A large inductance is connected in the dc circuit to maintain the dc current at 20 A ... thyristor will be reverse biased for a period of  (A) 125o (B) 120o (C) 60o (D) 55o

Last Answer : A solar cell of 350 V is feeding power to an ac supply of 440 V, 50 Hz through a 3-phase fully controlled bridge converter. A large inductance is connected in the dc circuit to maintain the ... the solar cell resistance is 0.5 Ohm ,then each thyristor will be reverse biased for a period of 125o

A 3-phase induction motor under locked rotor condition and with stator supply, induces

Description : A 3-phase induction motor under locked rotor condition and with stator supply, induces (A) small voltage at slip frequency (B) large voltage at rotor frequency (C) zero voltage at zero frequency (D) large voltage at slip frequency

Last Answer : A 3-phase induction motor under locked rotor condition and with stator supply, induces (A) small voltage at slip frequency (B) large voltage at rotor frequency (C) zero voltage at zero frequency (D) large voltage at slip frequency

A series wound DC motor has its armature and field connected in series with a resistor. When the motor is disconnected from its power supply, this motor will exemplify __________. A. the proper connections for across the line starting B. the proper connections for an automatic strip heater C. a reversing controller circuit D. dynamic braking

Description : A series wound DC motor has its armature and field connected in series with a resistor. When the motor is disconnected from its power supply, this motor will exemplify __________. A. the ... the proper connections for an automatic strip heater C. a reversing controller circuit D. dynamic braking

Last Answer : Answer: D

An open armature connection in a DC propulsion motor could be caused by ____________. A. low-load operation B. clogged ventilation ducts C. sparking at the brushes D. a grounded shunt field coil

Description : An open armature connection in a DC propulsion motor could be caused by ____________. A. low-load operation B. clogged ventilation ducts C. sparking at the brushes D. a grounded shunt field coil

Last Answer : Answer: B

Pick up the correct statement in case of water supply. (A) Pipes laid in trenches and pipes fixed to walls are measured separately (B) Cutting through walls and floors are included with the item (C) Pipes are classified according to their sizes and quality (D) All the above

Description : Pick up the correct statement in case of water supply. (A) Pipes laid in trenches and pipes fixed to walls are measured separately (B) Cutting through walls and floors are included with the item (C) Pipes are classified according to their sizes and quality (D) All the above

Last Answer : (D) All the above

The relative speed between the magnetic fields of stator and rotor under steady state operation is zero for a (A) dc machine. (B) 3 phase induction machine. (C) synchronous machine. (D) single phase induction machine.

Description : The relative speed between the magnetic fields of stator and rotor under steady state operation is zero for a (A) dc machine. (B) 3 phase induction machine. (C) synchronous machine. (D) single phase induction machine.

Last Answer : Ans: all options are correct

Why is it dangerous yo supply power to an unloaded series connected dc motor?

Description : Why is it dangerous yo supply power to an unloaded series connected dc motor?

Last Answer : Need answer

If the supply voltage is 220 volts 60 Hz, what is the operating voltage of the motor controller circuitry illustrated? EL-0011 A. 110 volts DC B. 110 volts AC C. 220 volts DC D. 220 volts AC

Description : If the supply voltage is 220 volts 60 Hz, what is the operating voltage of the motor controller circuitry illustrated? EL-0011 A. 110 volts DC B. 110 volts AC C. 220 volts DC D. 220 volts AC

Last Answer : Answer: D

The most common source of excitation for synchronous motors is a/an _____________. A. low voltage battery B. motor attenuator set C. DC exciter generator D. AC supply

Description : The most common source of excitation for synchronous motors is a/an _____________. A. low voltage battery B. motor attenuator set C. DC exciter generator D. AC supply

Last Answer : Answer: C

Explain what happens if a DC motor is fed with AC supply

Description : Explain what happens if a DC motor is fed with AC supply

Last Answer : Motor will run at low speed, sparking at brushes, heat due to eddy current will finally burn the motor.

A dc shunt generator has a speed of 800 rpm when delivering 20 A to the load at the terminal voltage of 220V. If the same machine is run as a motor it takes a line current of 20A from 220V supply. The speed of the machine as a motor will be (A) 800 rpm. (B) more than 800 rpm. (C) less than 800 rpm. (D) both higher or lower than 800 rpm.

Description : A dc shunt generator has a speed of 800 rpm when delivering 20 A to the load at the terminal voltage of 220V. If the same machine is run as a motor it takes a line current of 20A from 220V supply. The speed of ... . (B) more than 800 rpm. (C) less than 800 rpm. (D) both higher or lower than 800 rpm.

Last Answer : (C) less than 800 rpm.

Which of the listed sections of an emergency switchboard is used to supply power for alarm signals under emergency conditions? A. The generator and bus transfer section B. The 450 volt, 60 cycle, 3 phase bus C. The 120 volt, 3 phase, 60 cycle bus D. The 24 volt DC bus

Description : Which of the listed sections of an emergency switchboard is used to supply power for alarm signals under emergency conditions? A. The generator and bus transfer section B. The 450 volt, 60 cycle, 3 phase bus C. The 120 volt, 3 phase, 60 cycle bus D. The 24 volt DC bus

Last Answer : Answer: D

AC and DC generators are similar in that they _____________. A. both generate alternating voltages B. both rectify the voltage before delivery C. are constructed at the same physical size for the same kilowatt rating D. both supply three-phase power

Description : AC and DC generators are similar in that they _____________. A. both generate alternating voltages B. both rectify the voltage before delivery C. are constructed at the same physical size for the same kilowatt rating D. both supply three-phase power

Last Answer : Answer: A

A three phase slip ring induction motor with chopper controlled resistance has its torque

Description : A three phase slip ring induction motor with chopper controlled resistance has its torque proportional to   (a) Rotor current (b) Stator resistance (c) Square of rotor current (d) Square root of rotor current 

Last Answer : A three phase slip ring induction motor with chopper controlled resistance has its torque proportional to Square of rotor current

The speed of a three-phase induction motor is controlled by variable voltage variable frequency control

Description : The speed of a three-phase induction motor is controlled by variable voltage variable frequency control (i.e. keeping V/f constant). As the frequency is reduced, the slip at maximum torque  (1) Decreases (2) Increases (3) Remains constant (4) None of the above

Last Answer : The speed of a three-phase induction motor is controlled by variable voltage variable frequency control (i.e. keeping V/f constant). As the frequency is reduced, the slip at maximum torque Increases 

As shown in the illustration, the generator field is excited with DC current provided by ____________. EL-0016 A. conductors '1', '2' and '3' B. inductor 'L1' C. rectifier 'CR1' D. winding 'S-2'

Description : As shown in the illustration, the generator field is excited with DC current provided by ____________. EL-0016 A. conductors '1', '2' and '3' B. inductor 'L1' C. rectifier 'CR1' D. winding 'S-2'

Last Answer : Answer: C

The slight curvature at the lower end of the O.C.C. of a self-excited dc generator is due to

Description : The slight curvature at the lower end of the O.C.C. of a self-excited dc generator is due to  1. residual pole flux 2. high armature speed 3.magnetic inertia 4. high field circuit resistance

Last Answer : The slight curvature at the lower end of the O.C.C. of a self-excited dc generator is due to magnetic inertia

Erratic operation of the devices represented in the diagrams shown in the illustration could be traced to ____________. EL-0092 A. improper contact at 'R' slip rings or 'S' connections B. a low three-phase voltage supply C. improper contact at 'S' slip rings or 'R' connections D. a high three-phase voltage supply

Description : Erratic operation of the devices represented in the diagrams shown in the illustration could be traced to ____________. EL-0092 A. improper contact at 'R' slip rings or 'S' connections B. a low three- ... . improper contact at 'S' slip rings or 'R' connections D. a high three-phase voltage supply

Last Answer : Answer: A

Ward - Leonard controlled DC drives are generally used for:

Last Answer : Ward - Leonard controlled DC drives are generally used for:  Heavy duty excavators

The torque, in a _____________is proportional to the square of the armature current (A) DC shunt motor (B) stepper motor (C) 2-phase servomotor (D) DC series motor

Description : The torque, in a _____________is proportional to the square of the armature current (A) DC shunt motor (B) stepper motor (C) 2-phase servomotor (D) DC series motor

Last Answer : (D) DC series motor