If the rms voltage drop across a 15 kilt resistor is 16 V, the peak current through the resistor is : - 1.5 mA
Description : In a series RC circuit, 12 V (rms) is measured across.the resistor and 15 V (rms) is measured across the capacitor. The value of rms source voltage is: A. 3 V B. 27 V C. 19.2 V D. 1.9 V
Last Answer : In a series RC circuit, 12 V (rms) is measured across.the resistor and 15 V (rms) is measured across the capacitor. The value of rms source voltage is: 19.2 V
Description : Average power dissipated in resistor if sinusoidal p.d of peak value 25 V is connected across a 20 Ω resistor is A. 15.6 W B. 15 W C. 16 W D. 17 W
Last Answer : 15.6 W
Description : If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω
Last Answer : 500Ω
Description : A resistor of value R/2 is connected in parallel with a resistor of value R/3. The voltage drop across the parallel combination is V. The total current supplied by the voltage source is: w) 2 V/R (read: 2 V over R) x) 3 V/R (read: 3 V over R) y) 4 V/R (read: 4 V over R) z) 5 V/R (read: 5 V over R)
Last Answer : ANSWER: Z -- 5 V/R
Description : In the circuit shown the voltage drop across the `15Omega` resistor is `30 V` having the polarity as indicated. The ratio of potential difference acro
Last Answer : In the circuit shown the voltage drop across the `15Omega` resistor is `30 V` having the ... difference across `5Omega` and resistance `R` is
Description : Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor and 4.2 V rms across the other, the peak source voltage is? A.16.54 V B.1.65 V C.10.60 V D.5.93 V
Last Answer : Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor and 4.2 V rms across the other, the peak source voltage is? A.16.54 V B.1.65 V C.10.60 V D.5.93 V
Last Answer : Req= (1/1200 +1/560 + 1/2.1)^-1 = 2.1 ohms RT= 2.1 + 7.8 = 9.9 ohms IT = V/R = 24/9.9 = 2.4 A Veq= R I = 2.1 2 ... 7.8 = 12.096 w = 44.928 w _________________________________________ By: Ellis-Junior Kamatjipose [email protected]
Description : What is the RMS voltage in a series RL circuit, if the voltage across R and L is 256 V and 192 V respectively? A) 320 V B) 448 V C) 64 V D) None of these
Last Answer : What is the RMS voltage in a series RL circuit, if the voltage across R and L is 256 V and 192 V respectively? A) 320 V B) 448 V C) 64 V D) None of these
Description : Which of the following statements concerning a simple parallel resistance circuit is correct? A. The voltage drop across each resistor is the same. B. The total current flow equals the reciprocal ... resistances. D. The total voltage equals the sum of the individual voltages across each resistance.
Last Answer : Answer: A
Description : If the current was increased to 4 amps, what would be the voltage drop across each resistor in the circuit described in question 17?
Last Answer : E1 = 80 volts. E2 = 240 volts. E3 = 320 volts
Description : An LED is operated on a 12 volt automobile circuit. The voltage drop across the LED is 2 volts and the current must be limited to 50 milliamps to prevent its overheating and destruction. What size resistor must be used? w) 60 ohms x) 100 ohms y) 120 ohms z) 200 ohms
Last Answer : ANSWER: Z -- 200 OHMS
Description : What would be the voltage drop across the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts
Last Answer : Answer: C
Description : In a simple series circuit, the entire source voltage will drop across ______________. A. the resistor next to the negative terminal B. a short circuit C. the resistor next to the positive terminal D. an open circuit
Last Answer : Answer: D
Description : What is the voltage drop across the resistor in an RC charging circuit when the charge on the capacitor is equal to the battery voltage?
Last Answer : Zero.
Description : To determine the polarity of the voltage drop across a resistor, it is necessary to know?
Last Answer : To determine the polarity of the voltage drop across a resistor, it is necessary to know direction of current through the resistor.
Description : An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV
Last Answer : B. 4.0 µV
Description : When the peak output voltage is 100 V the PIV for each diode in a center-tapped full-wave rectifier is (neglecting the diode drop)?
Last Answer : Feel Free to Answer
Description : If the peak value of a sine wave is 30 V, the rms value is? A.19.08 V B.7.07 V C.0.707 V D.23.10 V
Last Answer : If the peak value of a sine wave is 30 V, the rms value is? A.19.08 V B.7.07 V C.0.707 V D.23.10 V
Description : A voltage of 30 V is applied across a colour coded carbon resistor with first, second and third rings of blue, black and yellow colurs. What is the cu
Last Answer : A voltage of 30 V is applied across a colour coded carbon resistor with first, second and ... What is the current flowing through the resistor ?
Description : With a 12 V supply, a silicon diode, and a 370 - ohm resistor in series, what voltage will be dropped across the diode? a) 0.3V b) 0.7V c) 0.9V d) 1.4V
Last Answer : 0.7V
Description : When there is 12 mA of current through a 1.2 k ohms resistor, the voltage across the resistor is? A.14.4 V B.1.4 V C.100 V D.10 V
Last Answer : When there is 12 mA of current through a 1.2 k ohms resistor, the voltage across the resistor is? A.14.4 V B.1.4 V C.100 V D.10 V
Description : Four amperes of current are measured through a 24 ohms resistor connected across a voltage source. How much voltage does the source produce? A.960 V B.9.6 V C.96 V D.8 V
Last Answer : Four amperes of current are measured through a 24 ohms resistor connected across a voltage source. How much voltage does the source produce? A.960 V B.9.6 V C.96 V D.8 V
Description : AC voltmeters are generally calibrated to read the ________. A. instantaneous voltage B. average voltage C. RMS voltage D. peak voltage
Description : The voltage at any point in an ac circuit will be a) Peak voltage b) RMS voltage c) Average voltage d) Source voltage
Last Answer : b) RMS voltage
Description : An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak Envelope Power? A) 49.98 W B) 79.98 W C) 99.96 W D) 199.93 W
Last Answer : An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak Envelope Power? A) 49.98 W B) 79.98 W C) 99.96 W D) 199.93 W
Description : In the circuit shown in Fig. 4.63, the terminal voltage of the battery is 6.0 V. Find the current I through the `18 Omega` resistor.
Last Answer : In the circuit shown in Fig. 4.63, the terminal voltage of the battery is 6.0 V. Find the current I through the `18 Omega` resistor.
Description : A single-phase ac voltage source has 200 V rms and a system connected consumes an active power of 300 W. What is the reactive power consumed by the system if 2.5 A rms current is drawn ? (a) 100 VAR (b) 200 VAR (c) 300 VAR (d) 400 VAR
Last Answer : A single-phase ac voltage source has 200 V rms and a system connected consumes an active power of 300 W. What is the reactive power consumed by the system if 2.5 A rms current is drawn ? 400 VAR
Description : Alternating current measured in a transmission line will be a) Peak value b) Average value c) RMS value d) Zero
Last Answer : c) RMS value
Description : Determine the voltage drop across the resistance `R_(1)` in the circuit given in Fig. 4.55 with `epsilon=90 V, R_(1)=5 k Omega, R_(2)=5k Omega, R_(3)=
Last Answer : Determine the voltage drop across the resistance `R_(1)` in the circuit given in Fig. 4.55 with `epsilon=90 V, ... k Omega " and " R_(4)=10 k Omega`.
Description : As shown in the illustration, if 'R1' and 'R2' have unequal values, the ____________. EL-0019 A. voltage drop across 'R1' will not be equal to the voltage drop across 'R2' B. current flow ... energy dissipated in 'R2' D. current flow through 'R1' will differ from the current flow through 'R2'
Description : In a DC series circuit, all the conductors have the same ____________. A. power expended in them B. voltage drop across them C. resistance to current flow D. current passing through them
Description : how is (a) the current through R2 and (b) the voltage drop across R2 computed?
Last Answer : (a) By adding the bleeder current (IR1) and the current through load 1(b) By subtracting the voltage of load 1 from the voltage of load 2.
Description : An ammeter has a full-scale deflection current of 100mA. If the same ammeter is used to measure a full-scale current of 1.0ampere, what is the value of the shunt resistor in ohms if the voltage across the meter is 9.0 volts?
Last Answer : 10 ohms
Description : The voltage induced across a certain coil is 200 mV. A 1200 resistor is connected to the coil terminals. The induced current will be: A. 1.7 mA B. 16 mA C. 12 mA D. 120 mA
Last Answer : The voltage induced across a certain coil is 200 mV. A 1200 resistor is connected to the coil terminals. The induced current will be: 1.7 mA
Description : The potential drop across the `3 Omega` resistor is
Last Answer : The potential drop across the `3 Omega` resistor is A. 1 V B. `1.5 V` C. 2 V D. 3 V
Description : 9 leds each of 1 volt drop is series with 9 volt battery , do we need a resistor?(SMD leds) I have seen some smd leds without resistor !
Last Answer : We connect resistor to limit the current. So, it depends upon the current rating of the LED, which is provided by manufacturer.
Description : The noise output of a resistor is amplified by a noiseless amplifier having a gain of 60 and a bandwidth of 20 kHz. A meter connected at the output of the amplifier reads 1mV RMS. If the bandwidth of the amplifier is reduced to ... does the meter read now? A. 0.5 mV B. 0.5 µV C. 5.0 mV D. 5.0 µV
Last Answer : A. 0.5 mV
Description : The distance between a generator and its load is 100 feet. What would be the approximate total voltage drop across a two wire supply cable if the current were 5.5 amperes and the resistance of the wire were 2.525 ohms per 1,000 feet? A. 0.5 volts B. 1.38 volts C. 1.90 volts D. 2.77 volts
Description : A conducting bar is slid at a constant velocity v along two conducting rods. The rods ar seprated by a distance l and connected across a resistor R. T
Last Answer : A conducting bar is slid at a constant velocity v along two conducting rods. The rods ar ... to determine the direction and nature of the current
Last Answer : A conducting bar is slid at a constant velocity v along two conducting rods. The rods ar seprated by a distance l ... apparatus? A. v B. l C. R D. B
Last Answer : A conducting bar is slid at a constant velocity v along two conducting rods. The rods ar seprated by a ... i generated by the apparantus? B. C. D.
Description : In an experiment on studying the dependence of current flowing through a given resistor on the potential difference applied across it, list two ways how a student would change the values of current in the circuit?
Last Answer : Answer. There are two ways in which a student can change the values of current in the circuit: By increasing or decreasing the number of cells. By changing the value of resistance.
Description : Can I use eurometer calibrated in RMS to measure HWDC in peak?
Last Answer : No
Description : In AC circuits, AC meters measure – (1) mean values (2) rms values (3) peak values (4) mean square values
Last Answer : (2) rms values Explanation: Voltages and currents for AC circuits are generally expressed as rms (root mean square) values. For a sine wave, the relationship between the peak and the rms average is: rms value = 0.707 peak value.
Description : What does the Voltmeter in AC mode show? Is it RMS value or peak value?
Last Answer : Multimeter in AC mode shows RMS value of the voltage or current. Also when it is DC mode it will show the RMS value only.
Description : External noise fields are measured in terms of _______. A. rms values B. dc values C. average values D. peak values
Last Answer : D. peak values
Description : In AC circuits, AC meters measure (1) mean values (2) rms values (3) peak values (4) mean square values
Last Answer : rms values
Description : What voltage would be measured across the 45 ohm resistor?
Last Answer : Not enough information. But if you know the current, you can useOhm's Law (just multiply the resistance times the current).
Description : For practical purposes, in a simple series circuit, the source voltage will be dropped across one resistor if it has ______________. A. half the resistance of the other resistor B. a resistance equal to the other C. at least ten times the resistance of the other D. a partial short circuit
Description : In general, polyphase induction motors can be started on full line voltage by means of ______________. A. compensator starters B. autotransformer starters C. across-the-line starters D. primary-resistor starters