Description : verticalsuctioninmouldboardploughis______whereashorizontalsuctionis______
Last Answer : .0.3to0.5cm,0.5cm
Description : Byincreasingdiskangle,depthpenetration_____beoverwithofcut_______
Last Answer : .decreases,increases
Description : A paddy transplanter uses either root wash type seedlings or __________ seedlings.
Last Answer : soil bearing
Description : An indigenous plough cuts a _________furrow cross sect
Last Answer : Trapizoidal
Description : The unit of filter medium resistance is________
Last Answer : L^-1
Description : The average working speed of a hand operated chaff fitted with two knives is _________ rev/min.
Last Answer : 35
Description : In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.
Last Answer : 1200 to 1500
Description : In sprayers , operating pressures below ___________Kpa are undesirable for hydraulic nozzles other than flooding type
Last Answer : 140
Description : Optimum speed for grains like gram,pea,etc.,thresher using power is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm
Last Answer : a) 300-400rpm
Description : Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm
Last Answer : d) 1100-1200rpm
Description : Optimum operating cylinder speed for the power operated maize sheller is a) 200-400rpm b) 400-600rpm c) 600-800rpm d) 1000-1200rpm
Last Answer : c) 600-800rpm
Description : Air output of a duster is given by formula a) Q= 60×A×V b)Q= 60×A×(2GH/Y) c) Q= 240×A×h d) all of the above
Last Answer : d) all of the above
Description : Lewis formula is used in the design of a) gears b) clutch c) chain drive d) belt drives
Last Answer : a) gears
Description : Transplanter using soil bearing seedlings are more popular than washed root seedling transplanter because of a) less labour requirement b) lesser plant missing percentage c) higher work rates d) all of the above
Description : Superchargers are driven by A. Electric current from the battery B. Exhaust gases from engine C. Direct connection with the engine power D. None of the above
Last Answer : C. Direct connection with the engine power
Description : Turbo chargers are driven by A. Direct connection with engine power B. Exhaust gases from engine C. Electric current from the battery D. None of the above
Last Answer : B. Exhaust gases from engine
Description : Turbo chargers or super chargers increases engine power by A. 10-20% C. 50-60% B. 20-30% D. 90-100%
Last Answer : A. 10-20%
Description : .When the valves are carried in engine bioel at one side of each cylinder is called A. Valves in head arrangements B. L-head C. I-head D. None of the above
Last Answer : B. L-head
Description : Utility index is a indication of A. Work machine contact hours B. Wear out life of machine C. Operating cost of machine D. Reliability of machine working
Last Answer : A. Work machine contact hours
Description : Alternators are preferred over dynamo because A. Alternators can produce a strong current of 30-40 amperes. B. Alternators don’t required cutout reiny C. Alternators don’t have commutaters D. All of the above
Last Answer : D. All of the above
Description : main function of the current regulator is A. To prevent the reversal flow of current from the battery when dynamo speed is drops. B. To safeguard against flow of high currents to battery when armature develops ... . C. To prevent building up of high voltage in a circuit. D. None of the above
Last Answer : B. To safeguard against flow of high currents to battery when armature develops more current.
Description : Main function of cutout relay in electrical circuit is A. To prevent the reversal of current flow from the battery when dynamo speed (engine speed) reduces. B. To restrict the maximum output at ... deliver current to the battery or to the lightening and ignition circuit. D. None of the above
Last Answer : A. To prevent the reversal of current flow from the battery when dynamo speed (engine speed) reduces.
Description : Weight per unit of drawbar power is generally ranges between a)50-120kg/kw b)120-150kg/kw c)150-250kg/kw d)250-300kg/kw
Last Answer : a)50-120kg/kw
Description : .Fandem wheels are preferred over dual wheels because a) they tends to reduce load on an area by50% b)they tends to reduce soil contact pressure c)reduces sub soil compact ness pressure d)none of the above
Last Answer : a) they tends to reduce load on an area by50%
Description : Dual wheels have disadvantage of a)reducing soil contact pressure and sub soil compact negative pressure b) concentrating load over an area c)reduces load on area by 50% d) none of the above
Last Answer : b) concentrating load over an area
Description : Suggested or recommended difference in mass to power ratio between ballasted and unballasted tractor is of the order a)10kg/PTO KW b)6kg/PTO kw c)20kg/PTO kw d)30kg/PTO kw
Last Answer : b)6kg/PTO kw
Description : Formula for adding weight (ballast) on tractor tyres working in loose wet soil for good traction a)(km/hr × kg/PTO kw)=540 b)( km/hr × kg/PTO kw)=670 c)( km/hr × kg/PTO HP)=540 d)( km/hr × kg/PTO HP)=670
Last Answer : a)(km/hr × kg/PTO kw)=540
Description : Optimum operating speed of rotavator is a)20-150rpm b)150-350rpm c)350-500rpm d) >500rpm
Last Answer : d) >500rpm
Description : For optimum working the slip should not exceed a) 15% b) 20% c) 25% d) 30%
Last Answer : a) 15%
Description : Curved twisted blades are specially suited for m. Minimum tillage of trashy land at shallow depths n. Dried hard soils o. Cutting and pulverisation in wet sticky clay soil p. For operating on the sides of plant bed
Last Answer : p. For operating on the sides of plant bed
Description : shaped blades are best suited for i. Minimum tillage of trashy land at shallow depths j. Dried hard soils k. Cutting and pulverisation in wet sticky clay soil l. Working under normal field conditions
Last Answer : i. Minimum tillage of trashy land at shallow depths
Description : Hook type blades best suited for e. Minimum tillage of trashy land at shallow depths f. Dried hard soils g. Cutting and pulverisation especially in wet sticky clay soil h. Working under normal field conditions
Last Answer : f. Dried hard soils
Description : Total mechanical losses ( frictional losses , pumping loss in intake and exhaust and power accessories) will amount to a.10-20 % ihp b.2-10 % ihp c.20-30 % ihp d.30 -50 % ihp
Last Answer : a.10-20 % ihp
Description : Detonation is favoured by a. Low crankshaft speed at full throttle b. .Higher loads c. Both (a) and (b) d. None of the above
Last Answer : c. Both (a) and (b)
Description : A traction fitted with diesel engine will have good slogging ability as lugging ability if it has a reserve of a.500 rpm d.200 rpm c.300 rpm e.1000 rpm
Last Answer : a.500 rpm
Description : Volumetric efficiency is affected by (A) Turbulence velocity and temperature of intake manifold (B) Efficiency of exhaust stroke (C) Valve timing overlap (D) All the above
Last Answer : (D) All the above
Description : Rated speed of an engine is the speed at which an engine devlopes (A) Maximum crankshaft torque (B) Maximum brake horse power output (C) Maximum thermal efficiency (D) Maximum drawback pull
Last Answer : (B) Maximum brake horse power output
Description : Brass is an alloy of copper and zinc having the relative percentage (A) 60-70% Cu and 30-40% Zn (B) 50-60% Cu and 40-50% Zn (C) 40-50 % Cu and 60-50% Zn (D) 30-40 % Cu and 60-70% Zn
Last Answer : A) 60-70% Cu and 30-40% Zn
Description : Bronze is an alloy of copper, zinc , and tin having composition (A) 60% - 30% - 10% (B) 70% - 20% - 10% (C) 88% - 2% - 10% (D) 50% -30% - 20%
Last Answer : (C) 88% - 2% - 10%
Description : High carbon steel having carbon content about (A) 0.25 % (B) 0.25 – 0.50 % (C) 0.50 – 1.5 % (D) 2.5 - 4.5 %
Last Answer : (C) 0.50 – 1.5 %
Description : Medium Carbon steel was carbon content about (A) 0.25 % (B) 0.25 – 0.50 % (C) 0.50 – 1.5 % (D) 2.5 – 4.5 %
Last Answer : (B) 0.25 – 0.50 %
Description : Carbon content in the cast iron is (A) 2.5 – 4.5 % (B) 0 – 0.25 % (C) 0.25 – 0.50 % (D) 0.50 – 1.5 %
Last Answer : (B) 0 – 0.25 %
Description : Worm gear are used for transmitting power between two Shaft Inclined at e. At right angle to each other and axes can intersect f. At right angle to each other but axis cannot intersect each other g. At right angle to each other and in different planes h. None of the above
Last Answer : f. At right angle to each other but axis cannot intersect each other
Description : Spiral gear are used for transmitting power between two shaft Inclined at a. Right angle to each other and axes can intersect b. Right angle to each other and axes cannot intersect c. At angle slightly lesser or greater than 90 of axles can meet d. None of the above
Last Answer : c. At angle slightly lesser or greater than 90 of axles can meet
Description : ears commonly used on fuel injection pumps are a. Spur gears b. helical gears c. rack and pinion d. spiral gears
Last Answer : c. rack and pinion
Description : V -belt are most suitable for a. less space requirements b. use with adjustable pulley foe speed change c. both (a) and (b) d. none of the above
Last Answer : c. both (a) and (b)
Description : Length of open belt is given by formula a. L=[2C+( 2) (DI+D2)] + [ /4C] b. L=[2C+( 2) (DI+D2)] + [ /4C] c. L=[2C+( 2) (DI+D2)] + [ ] d. L=[2C+( 2) (DI D2)] + [ ]
Last Answer : a. L=[2C+( 2) (DI+D2)] + [ /4C]
Description : Function of idler pully are a. to increase the angle of contact of belt on pully b. maintain belt tension as belt stretches c. canter to centre distance remain same d. all the above
Last Answer : d. all the above
Description : Belt Tension can be adjusted by a. idler pulley b. slide rails c. tilting plate drive d. all the above
Description : Slip of belt is responsible for A. Reduction is speed B. Reduction in power C. Reduction in belt life D. All of the above