Description : Land shaping becomes essential where often the following implement is used a) M.B. Plough b) Disc Harrow c) Cultivator d) All of the above
Last Answer : a) M.B. Plough
Description : .Land shipping become necessary often the following implments is used: a. MB plough b. Disc harrow c. Cultivator d. All of these
Last Answer : a. MB plough
Description : .Laying out of field in lands is essential when working with a. Two way plough b. One way plough c. Disc harrow d. Cultivator
Last Answer : b. One way plough
Description : Which one of the below is a multipurpose tool a) Indigenous plough b) Cultivator c) Multipurpose tool bar carrier d) M.B plough
Last Answer : c) Multipurpose tool bar carrier
Description : For maximum moisture conservation ploughing is done with A. mb plough b. cultivator c. chisel plough d. dice harrow
Last Answer : c. chisel plough
Description : Which plough will be used for maximum moisture conservation ? a. M B Plugh b. Cultivator c. Chisel plough d. Disc harrow
Last Answer : c. Chisel plough
Description : 1Heavy draft of a disc plough is due to: A. Blunt disc B. Furrows too wide C. Loose bearings D. All are currect
Last Answer : D. All are currect
Description : In a disc plough with the increase in the disk angle, the transverse component of reaction will a)Increase b) Decrease c) Unaffected d) None of the above
Last Answer : a)Increase
Description : The two primery tillage equipment a. MB plough and disc harrow b. Disc plough and disc harrow c. Disc harrow and cultivetor d. MB plough and subsoiler
Last Answer : d. MB plough and subsoiler
Description : Dead furrow is made by: a. One way MB plough b. Two way MB plough c. Ridger d. Disc harrow
Last Answer : a. One way MB plough
Description : A coulter attachment is used with: a. Disc harrow b. Seed drill c. MB plough d. Sub soiler
Last Answer : c. MB ploug
Description : Heavy draft of a disc plough is due to: a) Blunt disc b) Furrows too wide c) Loose bearings d) All of the above
Last Answer : d) All of the above
Description : The type of bearing generally used to support the discs on a standard disc plough is: A. Ball bearing. B. Tapered roller bearing. C. Plain roller bearing. D. Bush bearing.
Last Answer : B. Tapered roller bearing.
Description : Penetration of disc plough can be improved by a) Increase disc angle b) Decreasing tilt angle c) Both (a) and (b) d) None of the above
Last Answer : b) Decreasing tilt angle
Description : At smaller disc angles , the draft tends to increase in disc plough because of a) Greater contact area between furrow wall and the convex side of the disc b) Increase in the side draft c) Greater throw of the soil d) All of the above
Last Answer : a) Greater contact area between furrow wall and the convex side of the disc
Description : The implement which can work in offset position a)offset disc harrow b) mower c) both (a) and (b) d) none of the above
Last Answer : c) both (a) and (b)
Description : 0ff-set disc harrows are best suitable to work for a) primary implement b) breaking clods c) orchard cultivation d) surface finishing
Last Answer : c) orchard cultivation
Description : The two primary tillage equipments are 1. MB and disc harrow 2. Disc plough and disc harrow 3. Disc harrow and cultivator 4. MB and subsoiler
Last Answer : ans 4
Description : The two primary tillage equipments are A. MB and disc harrow B. Disc plough and disc harrow C. Disc harrow and cultivator. D. MB and. Subscriber
Last Answer : MB and disc harrow
Description : .The land side of a mould board plough is made of: A. Malleable iron B. Forged steel C. C45 steel D. Soft Centre steel
Last Answer : D. Soft Centre steel
Description : .Increase length of a land slide of a one bottom right hand mould board plough will a) Increase the amount of offset on tractor b) Decrease the amount of offset c) No affect d) Affect Completely
Last Answer : c) No affect
Description : A power tiller is relatively more suitable for : A. Puddling of low land paddy fields with a rotary tiller B. Primary tillage of upland paddy fields with a rotary tillers C. Primary tillage with a mould board plough D. Farm transportation work
Last Answer : A. Puddling of low land paddy fields with a rotary tiller
Description : An indigenous plough cuts a _________furrow cross sect
Last Answer : Trapizoidal
Description : Subsoiler plough is best suited for a. breaking hard pan b. deep ploughing c. making ditches d. inter cultivation
Last Answer : a. breaking hard pan
Description : Vetical suction of plough influences: a. Pulverization b. Depth of cut c. Width of cut d. Direction of cut
Last Answer : b. Depth of cut
Description : the time taken to plough one acre farm with 35 hp tractor is : A)60 minutes b)75 minutes C)90 minutes d)120 minutes
Last Answer : b)75 minutes
Description : The landside of a mould board plough is made of: a) Malleable iron b) Forged steel c) C45 steel d) Soft centre steel
Last Answer : d) Soft centre steel
Description : owest specific energy requirement for the operation of rotavator is about _______ times as great as a mould board plough working in the same soil. a) Equal b) Twice c) Three d) Four
Last Answer : c) Three
Description : …………………………... moves the trash and roots from ahead of shin towords the main furrow so as 10 ensure complete coverage by the plough bottom a. Coulter b. Jointer c. Mould board d. Shin
Last Answer : b. Jointer
Description : A mould board plough bottom acts as a a. Single sided wedge b. Double sided wedge c. Three sided wedge d. All of the above
Last Answer : c. Three sided wedg
Description : Total force exerted upon the implement by a power unit called a)pull. B) draft C)side draft. D)unit draft
Last Answer : a)pull
Description : Depth of working of a tillage implement is controlled by a) Furrow Wheel b) Gauge Wheel c) Cage Wheel d) Star Wheel
Last Answer : d) Star Wheel
Description : The virtual hitch point of a directional implement is located at: a) Near the front axle b) 40 mm towards the rear axle c) At the power take off shaft d) Between two lower links
Last Answer : d) Between two lower links
Description : The type of restrained three point linkage system in which the depth of implement is automatically adjusted to maintain a pre selected constant draft is called : E. Automatic draft control system F. Precision control system G. Depth control system H. None of the above
Last Answer : E. Automatic draft control system
Description : raft increases with increase in forward speed for most of the implement, mainly due to a) More rapid acceleration of any soil particles that is moved appreciably b) More working width c) Increased working depth d) Draft decreases with increase in speed of implement
Last Answer : a) More rapid acceleration of any soil particles that is moved appreciably
Description : Under a given set of operating conditions, the designer and operator has some control of a)Useful soil resistance b) Parasitic Force c)Draft of implement d) Pull of implement
Last Answer : b) Parasitic Force
Description : Force ( including rolling resistance friction ) that acts upon the stabilising surfaces such landslide and sole of bottom are called a) Useful soil resistance b) Parasitic force d) Draft of implement. d) Pull of implement
Last Answer : b) Parasitic force
Description : Forces which a tool must overcome in cutting, breaking and moving the soil is called a) Useful soil resistance b) Parasitic force c) Draft of implement d) Pull of implement
Last Answer : a) Useful soil resistance
Description : A Tillage implement moving at a constant velocity is subjected to a) Force of gravity b) Soil force (resistance) c) Pull of mower d) All of the above
Description : Which of the following is not a tractor drawn tillage tool? 1. Cultivator 2. Augar plough 3. Harrow 4. Plank
Description : is not a tractor drawn tillage tool A. Cultivator B. Augar plough C. Narrow D. Plank
Last Answer : Plank
Description : is not a tractor drawn tillage tool: a) Cultivator c) Augar plough b) Harrow d) Plank
Description : is implement for churning the soil with water. a. Mixer b. Cultivator d. None of the above
Last Answer : Ans - c. Puddler
Description : In an offset disc harrow the angle between two gang is a) less than 90 degree b) 90 degree c) greater than 90 degree d) 180degree
Last Answer : a) less than 90 degre
Description : n single action disc harrow the two gangs are at set single a) less than 90 degree b) at 90 degree c) greater than 90 degree d) at 180 degree
Last Answer : c) greater than 90 degree
Description : Which end of the disc harrow penetrates deeply a) Concave b) Convex c) Rear d) Front
Last Answer : a) Concave
Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type c) Spike tooth d) Hammer mill
Last Answer : a) Raspbar type cylinder
Description : In standard disc plow the tilk angel varies between: A.30-40 ° B.40-45° C.20-25° D.2-3°
Last Answer : C.20-25°
Description : Width of cut of disc plow is increased by a)Increasing disc angle b)Increasing tilt angle c)addition of more weight d)Decreasing disc angle
Last Answer : a)Increasing disc angle