To construct a step down transformer, the condition is: a. Ns > Np b. Np > Ns c. Np = Ns d. Np . Ns = 1

To construct a step down transformer, the condition is:
a. Ns > Np b. Np > Ns c. Np = Ns d. Np . Ns = 1
by

1 Answer

Answer :

c. Np = Ns
by

Related questions

A transformer steps down 220V to 40 volts. If the secondary turns are 40 then primary turns will be: a. 20 b. 40 c. 120 d. 220

Description : A transformer steps down 220V to 40 volts. If the secondary turns are 40 then primary turns will be: a. 20 b. 40 c. 120 d. 220

Last Answer : d. 220V

The transfer function of a system is 10/(1+s) when operating as a unity feedback system, the steady state error to a step input will be a) 0 b) 1/11 c) 10 d) Infinity

Description : The transfer function of a system is 10/(1+s) when operating as a unity feedback system, the steady state error to a step input will be a) 0 b) 1/11 c) 10 d) Infinity

Last Answer : Ans: 1/11

To couple a coaxialline toa parallel-wire line,itisbesttouse a a. slotted line b.balun c. directional coupler d. quarter-wave transformer

Description : To couple a coaxialline toa parallel-wire line,itisbesttouse a a. slotted line b.balun c. directional coupler d. quarter-wave transformer

Last Answer : b.balun

What is a current transformer and voltage transformer?*

Description : What is a current transformer and voltage transformer?*

Last Answer : In electrical engineering, a current transformer (CT) is used for measurement of electric currents. Current transformers, together with voltage transformers (VT) (potential transformers (PT)), ... transformers are commonly used in metering and protective relays in the electrical power industry.

Why are motor ratings given in KW and that of alternator and transformer given in KVA?

Description : Why are motor ratings given in KW and that of alternator and transformer given in KVA?

Last Answer : kW is the output mechanical power of a motor and is expressed in kW. kVA is the net (apparent) power input to the transformer. This input power is the output + losses. kW = kVA x system power factor

Which of the following converts electric energy into mechanical energy: a. Transformer b. DC generator c. Motor d. AC generator

Description : Which of the following converts electric energy into mechanical energy: a. Transformer b. DC generator c. Motor d. AC generator

Last Answer : d. AC generato

The induced current in transformer which produced in the direction perpendicular to flux, is known as: a. Conventional current b. electronic current c. Perpendicular current d. Eddy current

Description : The induced current in transformer which produced in the direction perpendicular to flux, is known as: a. Conventional current b. electronic current c. Perpendicular current d. Eddy current

Last Answer : c. Perpendicular current

The most common source of AC voltage is: a. motor b. generator c. cell d. transformer

Description : The most common source of AC voltage is: a. motor b. generator c. cell d. transformer

Last Answer : c. cell

The loss of energy over each A.C cycle magnetization and demagnetization of transformer, is called: a. Magnetization loss b. Hysteresis loss c. Demagnetization loss d. energy loss

Description : The loss of energy over each A.C cycle magnetization and demagnetization of transformer, is called: a. Magnetization loss b. Hysteresis loss c. Demagnetization loss d. energy loss

Last Answer : c. Demagnetization loss

The application of mutual induction is: a. TV b. Radio c. Transformer d. Motor

Description : The application of mutual induction is: a. TV b. Radio c. Transformer d. Motor

Last Answer : c. Transformer

An ideal transformer always obeys the law of conservation of........: a. energy b. momentum c. charge d. Flux

Description : An ideal transformer always obeys the law of conservation of........: a. energy b. momentum c. charge d. Flux

Last Answer : b. momentum

A transformer: a. Works on A.C. only b. Works on D.C only c. Works on A.C. and D.C d. Has no hysteresis loss

Description : A transformer: a. Works on A.C. only b. Works on D.C only c. Works on A.C. and D.C d. Has no hysteresis loss

Last Answer : a. Works on A.C. only

Turn ratio of a transformer is 5. If 220 V AC is applied to its primary coil, voltage in the secondary coil will be: a. 44V b. 4.4 V c. 220V d. 1100V

Description : Turn ratio of a transformer is 5. If 220 V AC is applied to its primary coil, voltage in the secondary coil will be: a. 44V b. 4.4 V c. 220V d. 1100V

Last Answer : c. 220V

Explain the electrical characteristics of transformer.

Description : Explain the electrical characteristics of transformer.

Last Answer : Transformer electrical characteristics: Area of primary and secondary conductors, Apri and Asec: Winding loss Pw: Flux density and core loss: Leakage inductance: ... transformer span. The rise in temperature may breakdown insulation which may cause failure of the transformer.

is efficiency of transformer is greater than electrical machine and why?

Last Answer : The efficiency of transformer is Greater than electrical Machine because there is no rotational losses in transformer and there is no air gap losses in transformer so losses is less in transformer compare to electrical machine so efficiency is higher in case of transformer.

Explain the condition for Paralleling of Alternators?

Description : Explain the condition for Paralleling of Alternators?

Last Answer : The following conditions must be fulfilled for proper synchronizing of alternators. The terminal voltage of the incoming machine must be approximately equal to bus-bar voltage. The frequency of the incoming ... sequence of the incoming machine voltages must be the same as that of the bus-bars.

Find the false statement: (A) The relationship construct known as the weak relationship type was defined by Dey, Storey & Barron (1999). (B) A weak relationship occurs when two relationship types are linked by either Event-Precedent sequence or Condition-Precedent sequence (C) Conceptual model is not accurate representation of "Universe of interest". (D) Ternary, Quaternary and Quintary relationships are shown through a series of application scenario's and vignette's

Description : Find the false statement: (A) The relationship construct known as the weak relationship type was defined by Dey, Storey & Barron (1999). (B) A weak relationship occurs when two ... Ternary, Quaternary and Quintary relationships are shown through a series of application scenario's and vignette's

Last Answer : (C) Conceptual model is not accurate representation of "Universe of interest".

In a semiconductor diode, p-side is earthed and to n-side is applied a potential of -2 volt; the diode shall (a) Conduct (b) Not conduct (c) Conduct partially (d) Break down

Description : In a semiconductor diode, p-side is earthed and to n-side is applied a potential of -2 volt; the diode shall (a) Conduct (b) Not conduct (c) Conduct partially (d) Break down

Last Answer : a) Conduct

Which quantity remains constant in a step-down transformer? -Do You Know?

Description : Which quantity remains constant in a step-down transformer? -Do You Know?

Last Answer : answer:

Which quantity remains constant in a step-down transformer? -Do You Know?

Description : Which quantity remains constant in a step-down transformer? -Do You Know?

Last Answer : answer:

Which quantity remains constant in a step-down transformer? -Do You Know?

Description : Which quantity remains constant in a step-down transformer? -Do You Know?

Last Answer : answer:

Which quantity remains constant in a step-down transformer? -Do You Know?

Description : Which quantity remains constant in a step-down transformer? -Do You Know?

Last Answer : answer:

Which quantity remains constant in a step-down transformer? -Do You Know?

Description : Which quantity remains constant in a step-down transformer? -Do You Know?

Last Answer : answer:

Which quantity remains constant in a step-down transformer? -Do You Know?

Description : Which quantity remains constant in a step-down transformer? -Do You Know?

Last Answer : answer:

What is the way to understand transformer step up or step down ?

Description : What is the way to understand transformer step up or step down ?

Last Answer : How to understand the step-up or step-down of a transformer: If the number of patches on the secondary side is more than the primary side of the transformer, then that transformer is a step-up ... than the primary side of the transformer, then that transformer is a step down transformer.

How do I step down a step up transformer ?

Description : How do I step down a step up transformer ?

Last Answer : If we want to step up a transformer, we need to punch more of the secondary coil than the number of punches of the primary coil of the transformer. And in order to determine the number of these ... already been written on our electronics site, I did not repeat it. Read the article from this link.

What is a descending or step down transformer ?

Description : What is a descending or step down transformer ?

Last Answer : A transformer that converts a low current of high voltage to a high current of low voltage is called a descending or step down transformer.

What is a step down transformer ?

Description : What is a step down transformer ?

Last Answer : If you get low voltage with high voltage supply, it is called step down transformer.

When used for taking resistance measurements, a volt-ohm-milliammeter is normally powered by _____________. A. a hand cranked generator B. internal storage batteries C. the current in the circuit being tested D. a step down transformer

Description : When used for taking resistance measurements, a volt-ohm-milliammeter is normally powered by _____________. A. a hand cranked generator B. internal storage batteries C. the current in the circuit being tested D. a step down transformer

Last Answer : Answer: B

What can be used to replace the exciter in the circuit shown in the illustration? EL-0101 A. A step-up transformer. B. A rectifier. C. A step-down transformer. D. An operational amplifier.

Description : What can be used to replace the exciter in the circuit shown in the illustration? EL-0101 A. A step-up transformer. B. A rectifier. C. A step-down transformer. D. An operational amplifier.

Last Answer : Answer: B

When a transformer is used to step down voltage, the low voltage winding is _____________. A. part of the core B. the primary coil C. not insulated D. the secondary coil

Description : When a transformer is used to step down voltage, the low voltage winding is _____________. A. part of the core B. the primary coil C. not insulated D. the secondary coil

Last Answer : Answer: D

What is the maximum current allowed to be drawn from the secondary of a 2 KVA step-down transformer with a turns ratio of four to one if connected across a 440 volt line? A. 1.1 amps B. 4.5 amps C. 18.1 amps D. 22.7 amps

Description : What is the maximum current allowed to be drawn from the secondary of a 2 KVA step-down transformer with a turns ratio of four to one if connected across a 440 volt line? A. 1.1 amps B. 4.5 amps C. 18.1 amps D. 22.7 amps

Last Answer : Answer: C

What is the maximum allowable primary current of a 2 KVA step-down transformer with a four to one turns ratio if connected across a 440 volt line? A. 1.1 amps B. 4.5 amps C. 18.1 amps D. 27.7 amps

Description : What is the maximum allowable primary current of a 2 KVA step-down transformer with a four to one turns ratio if connected across a 440 volt line? A. 1.1 amps B. 4.5 amps C. 18.1 amps D. 27.7 amps

Last Answer : Answer: B

What are the applications of step-up & step-down transformer?

Description : What are the applications of step-up & step-down transformer?

Last Answer : A:Step-up transformers are used in generating stations. Normally the generated voltage will be either 11kV. This voltage (11kV) is stepped up to 110kV or 220kV or ... and made available at consumer premises. The transformers used at generating stations are called power transformers.

What is transformation ratio for step up, step down and isolation transformer?

Description : What is transformation ratio for step up, step down and isolation transformer?

Last Answer : K>1 for step up transformer K

Which quantity remains constant in a step-down transformer?

Description : Which quantity remains constant in a step-down transformer?

Last Answer : Power

What is a step down transformer?

Description : What is a step down transformer?

Last Answer : A transformer which decreases the input voltage of the AC source is called step down transformer.

If output voltage is greater than input voltage, then transformer is A. step up B. step down C. faulty D. fatal

Description : If output voltage is greater than input voltage, then transformer is A. step up B. step down C. faulty D. fatal

Last Answer :  step up

In step down transformer, the AC output gives the current _________ than the input current.

Description : In step down transformer, the AC output gives the current _________ than the input current.

Last Answer : more

Which of the following devices will receive voltage surge first travelling on the transmission line ? (a) Lightning arresters (b) Relays (c) Step-down transformer (d) Switchgear

Description : Which of the following devices will receive voltage surge first travelling on the transmission line ? (a) Lightning arresters (b) Relays (c) Step-down transformer (d) Switchgear

Last Answer : (a) Lightning arresters

Does 1:5 indicate a step-up or step-down transformer?

Description : Does 1:5 indicate a step-up or step-down transformer?

Last Answer : Step up.

Does 1:5 indicate a step-up or step-down transformer?

Description : Does 1:5 indicate a step-up or step-down transformer?

Last Answer : Step up

The doorbell on your house requires a 12 volt alternating current. A transformer having a primary winding of 1,600 turns is to be used to step down your house's 110-volt alternating current. How many turns are there on the secondary winding?

Description : The doorbell on your house requires a 12 volt alternating current. A transformer having a primary winding of 1,600 turns is to be used to step down your house's 110-volt alternating current. How many turns are there on the secondary winding?

Last Answer : ANSWER: 175 TURNS 

A generator is connected through a 20 MVA, 13.8/138 kV step down transformer, to a transmission line.

Description : A generator is connected through a 20 MVA, 13.8/138 kV step down transformer, to a transmission line. At the receiving end of the line a load is supplied through a step down transformer of 10 MVA, 138/69 kV rating. A 0.72 ... load (in per unit) in generator will be (A) 36 (B) 1.44 (C) 0.72 (D) 0.18

Last Answer : A generator is connected through a 20 MVA, 13.8/138 kV step down transformer, to a transmission line. At the receiving end of the line a load is supplied through a step down transformer of 10 MVA, 138/ ... MVA and 69 kV in load circuit, the value of the load (in per unit) in generator will be 36 

A single-phase, 230 V, 50 Hz ac mains fed step down transformer (4:1) is supplying power to a half-wave

Description : A single-phase, 230 V, 50 Hz ac mains fed step down transformer (4:1) is supplying power to a half-wave uncontrolled ac-dc converter used for charging a battery (12 V dc) with the series current limiting resistor being 19.04 Ohm. The charging current is  (A) 2.43 A (B) 1.65 A (C) 1.22 A (D) 1.0 A

Last Answer : A single-phase, 230 V, 50 Hz ac mains fed step down transformer (4:1) is supplying power to a half-wave uncontrolled ac-dc converter used for charging a battery (12 V dc) with the series current limiting resistor being 19.04 Ohm. The charging current is 1.0 A

In a step-up or step-down transformer, electrical power is transferred from one circuit to another without change in

Description : In a step-up or step-down transformer, electrical power is transferred from one circuit to another without change in

Last Answer : In a step-up or step-down transformer, electrical power is transferred from one circuit to another without change in frequency

Step-down transformer converts high voltage and low current into:

Description : Step-down transformer converts high voltage and low current into:  (A) How voltage and high current (B) High voltage and low current (C) Low voltage and high current (D) None of the above

Last Answer : Step-down transformer converts high voltage and low current into: Low voltage and high current

A 1100 kVA, 11 kV/1.1 kV conventional two-winding transformer is connected as a 12.1 kV/11 kV step-down ...

Description : A 1100 kVA, 11 kV/1.1 kV conventional two-winding transformer is connected as a 12.1 kV/11 kV step-down auto-transformer. The rating of the auto-transformer is (A) 1000 kVA (B) 1100 kVA (C) 11000 kVA (D) 12100 kVA

Last Answer : A 1100 kVA, 11 kV/1.1 kV conventional two-winding transformer is connected as a 12.1 kV/11 kV step-down auto-transformer. The rating of the auto-transformer is 12100 kVA

In a step-down transformer, there is a change of 15 A in the load current. This results in change of supply current of?

Description : In a step-down transformer, there is a change of 15 A in the load current. This results in change of supply current of?

Last Answer : In a step-down transformer, there is a change of 15 A in the load current. This results in change of supply current of less than 15A.