For a light detector, responsivity is measured in: a. amps per watt b. µW per amp c. mA per joule d. µsec per µW

For a light detector, responsivity is measured in:
a. amps per watt b. µW per amp  
c. mA per joule d. µsec per µW
by

1 Answer

Answer :

a. amps per watt
by

Related questions

The minimum optical power a light detector can receive and still produce a usable electrical output signal. ∙ A. light responsivity ∙ B. light sensitivity ∙ C. light collectivity ∙ D. illumination

Description : The minimum optical power a light detector can receive and still produce a usable electrical output signal. ∙ A. light responsivity ∙ B. light sensitivity ∙ C. light collectivity ∙ D. illumination

Last Answer : B. light sensitivity

The term responsivity as it applies to a light detector is best described as ∙ A. the time required for the signal to go from 10 to 90 percent of maximum amplitude ∙ B. the ratio of the diode output current to the input optical power ∙ C. the ratio of the input power to output power ∙ D. the ratio of output current to input current

Description : The term responsivity as it applies to a light detector is best described as ∙ A. the time required for the signal to go from 10 to 90 percent of maximum amplitude ∙ B. the ratio of the diode ... . the ratio of the input power to output power ∙ D. the ratio of output current to input current

Last Answer : the ratio of the diode output current to the input optical power

A measure of conversion efficiency of a photodetector. ∙ A. Efficiency ∙ B. Responsivity ∙ C. Dark current ∙ D. Spectral response

Description : A measure of conversion efficiency of a photodetector. ∙ A. Efficiency ∙ B. Responsivity ∙ C. Dark current ∙ D. Spectral response

Last Answer : B. Responsivity

Name the quantities which are measured by the following units. (i) Newton (ii) Joule (iii) Watt (iv) Volt (v) Light year (vi) Angstrom (vii) Acre-foot (viii) Becquerel (ix) Hertz (x) Cusec

Description : Name the quantities which are measured by the following units. (i) Newton (ii) Joule (iii) Watt (iv) Volt (v) Light year (vi) Angstrom (vii) Acre-foot (viii) Becquerel (ix) Hertz (x) Cusec

Last Answer : Answers: (i) Force (ii) Work Energy (iii) Power of electricity (iv) Potential difference (v) Distance of stars and planets (vi) Length (vii) Volume (viii) Radioactivity (ix) Frequency (x) Rate of flow of water

The term responsivity as it applies to a light detector is best described as.

Description : The term responsivity as it applies to a light detector is best described as.

Last Answer : the ratio of the diode output current to the input optical power

Light intensity is generally described in terms of __________ and measured in _________. ∙ A. Luminous flux density; Lumens per unit area ∙ B. Luminous flux intensity; Lumens per unit area ∙ C. Luminous flux density; Lumens per unit volume ∙ D. Luminous flux intensity; Lumens per unit volume

Description : Light intensity is generally described in terms of __________ and measured in _________. ∙ A. Luminous flux density; Lumens per unit area ∙ B. Luminous flux intensity; Lumens per unit area ∙ C. Luminous flux density; Lumens per unit volume ∙ D. Luminous flux intensity; Lumens per unit volume

Last Answer : Luminous flux density; Lumens per unit area

A ____________________ diode is the usual light detector for single-mode

Description : A ____________________ diode is the usual light detector for single-mode

Last Answer : PIN

How can modal dispersion reduced entirely? ∙ A. Use a graded index fiber ∙ B. Use a single-mode fiber ∙ C. Use a monochromatic light source ∙ D. Use a very sensitive light detector

Description : How can modal dispersion reduced entirely? ∙ A. Use a graded index fiber ∙ B. Use a single-mode fiber ∙ C. Use a monochromatic light source ∙ D. Use a very sensitive light detector

Last Answer : Use a single-mode fiber

Chromatic dispersion can be eliminated by __________. ∙ A. using a monochromatic light source ∙ B. using a very small numerical aperture fiber ∙ C. using a graded-index fiber ∙ D. using a very sensitive photo detector

Description : Chromatic dispersion can be eliminated by __________. ∙ A. using a monochromatic light source ∙ B. using a very small numerical aperture fiber ∙ C. using a graded-index fiber ∙ D. using a very sensitive photo detector

Last Answer : A. using a monochromatic light source

What parameter of light detector determines the range or system length that can be achieved for a given wavelength? ∙ a. Transit time ∙ b. Spectral response ∙ c. Dark current ∙ d. Responsitivity

Description : What parameter of light detector determines the range or system length that can be achieved for a given wavelength? ∙ a. Transit time ∙ b. Spectral response ∙ c. Dark current ∙ d. Responsitivity

Last Answer : ∙ b. Spectral response

Which of the following is NOT a common light detector ∙ a. PIN photodiode ∙ b. Photovoltaic diode ∙ c. Photodiode ∙ d. Avalanche photodiode

Description : Which of the following is NOT a common light detector ∙ a. PIN photodiode ∙ b. Photovoltaic diode ∙ c. Photodiode ∙ d. Avalanche photodiode

Last Answer : ∙ b. Photovoltaic diode

For efficient operation, should a detector have a high or low responsivity at the operating wavelength?

Description : For efficient operation, should a detector have a high or low responsivity at the operating wavelength?

Last Answer : High.

What is the unit of responsitivity? ∙ a. Ampere/volt ∙ b. Ampere/watt ∙ c. Watt/ampere ∙ d. Volts/ampere

Description : What is the unit of responsitivity? ∙ a. Ampere/volt ∙ b. Ampere/watt ∙ c. Watt/ampere ∙ d. Volts/ampere

Last Answer : ∙ a. Ampere/volt

When connector losses, splice losses and coupler losses are added, what is the limiting factor? ∙ A. source power ∙ B. fiber attenuation ∙ C. connector and splice loss ∙ D. detector sensitivity

Description : When connector losses, splice losses and coupler losses are added, what is the limiting factor? ∙ A. source power ∙ B. fiber attenuation ∙ C. connector and splice loss ∙ D. detector sensitivity

Last Answer : D. detector sensitivity

The three major groups of the optical system are ∙ A. the components, the data rate and the response time ∙ B. the source, the link and the receiver ∙ C. the transmitter, the cable and the receiver ∙ D. the source, the link and the detector

Description : The three major groups of the optical system are ∙ A. the components, the data rate and the response time ∙ B. the source, the link and the receiver ∙ C. the transmitter, the cable and the receiver ∙ D. the source, the link and the detector

Last Answer : B. the source, the link and the receiver

Which optical detector is used when high sensitivity and bandwidth are required? ∙ a. PMT ∙ b. APD ∙ c. PIN ∙ d. Phototransistor

Description : Which optical detector is used when high sensitivity and bandwidth are required? ∙ a. PMT ∙ b. APD ∙ c. PIN ∙ d. Phototransistor

Last Answer : a. PMT

One of the following is not a solid-state optical detector ∙ a. APD ∙ b. PIN ∙ c. PMT ∙ d. Phototransistors

Description : One of the following is not a solid-state optical detector ∙ a. APD ∙ b. PIN ∙ c. PMT ∙ d. Phototransistors

Last Answer : . PMT

The _____ of a detector is the fraction of incident photons that produce a photoelectron or electron-hole pair ∙ a. Responsitivity ∙ b. Photon efficiency ∙ c. Aperture ∙ d. Quantum efficiency

Description : The _____ of a detector is the fraction of incident photons that produce a photoelectron or electron-hole pair ∙ a. Responsitivity ∙ b. Photon efficiency ∙ c. Aperture ∙ d. Quantum efficiency

Last Answer : d. Quantum efficiency

APD stands for: a. Avalanche Photodiode b. Advanced Photodiode c. Avalanche Photo Detector d. Advanced Photo Detector

Description : APD stands for: a. Avalanche Photodiode b. Advanced Photodiode c. Avalanche Photo Detector d. Advanced Photo Detector

Last Answer : a. Avalanche Photodiode

EMD is best described by which statement? ∙ A. 70 percent of the core diameter and 70% of the fiber NA should be filled with light. ∙ B. 70 percent of the fiber diameter and 70% of the cone of acceptance should be filled with light. ∙ C. 70 percent of input light should be measured at the output. ∙ D. 70 percent of the unwanted wavelengths should be attenuated by the fiber.

Description : EMD is best described by which statement? ∙ A. 70 percent of the core diameter and 70% of the fiber NA should be filled with light. ∙ B. 70 percent of the fiber diameter and 70% of the ... be measured at the output. ∙ D. 70 percent of the unwanted wavelengths should be attenuated by the fiber.

Last Answer : 70 percent of the core diameter and 70% of the fiber NA should be filled with light.

If the voltage supplied to the lighting circuit is 110 volts, how much current is used by a 100 watt light bulb? A. 0.08 amps B. 0.91 amps C. 1.10 amps D. 90.9 amps

Description : If the voltage supplied to the lighting circuit is 110 volts, how much current is used by a 100 watt light bulb? A. 0.08 amps B. 0.91 amps C. 1.10 amps D. 90.9 amps

Last Answer : Answer: B

Used normally, a 150-watt, 120 volt light bulb requires how many amps of current?

Description : Used normally, a 150-watt, 120 volt light bulb requires how many amps of current?

Last Answer : ANSWER: 1.25 AMPS 

The force which produces an acceleration of 1 m/sec2 in a mass of 1 kg is called a.100 ergs b.one Newton c.one watt d.One erg e.one joule

Description : The force which produces an acceleration of 1 m/sec2 in a mass of 1 kg is called a.100 ergs b.one Newton c.one watt d.One erg e.one joule

Last Answer : b. one Newton

Which of the following is not a unit of energy? a.Joule b.kW c.N-m d.Electron volt e.Watt-hour

Description : Which of the following is not a unit of energy? a.Joule b.kW c.N-m d.Electron volt e.Watt-hour

Last Answer : b. kW

The unit of power in S.I. units is (A) Newton meter (B) Watt (C) Joule (D) Kilogram meter/sec

Description : The unit of power in S.I. units is (A) Newton meter (B) Watt (C) Joule (D) Kilogram meter/sec

Last Answer : (B) Watt

5. Unit of surface tension in S.I. unit is (A) Watt/m (B) Joule/m2 (C) Newton/m2 (D) Joule/m

Description : 5. Unit of surface tension in S.I. unit is (A) Watt/m (B) Joule/m2 (C) Newton/m2 (D) Joule/m

Last Answer : Option B

_________ is the quantity of heat required to raise the temperature of one pound of water 1 F˚ from 63 ˚F to 64 ˚F.  a. one Joule  b. one calorie  c. one watt  d. one BTU

Description : _________ is the quantity of heat required to raise the temperature of one pound of water 1 F˚ from 63 ˚F to 64 ˚F.  a. one Joule  b. one calorie  c. one watt  d. one BTU

Last Answer : one BTU

The unit of power in S.I. units is  (a) newton  (b) pascal  (c) erg  (d) watt  (e) joule.

Description : The unit of power in S.I. units is  (a) newton  (b) pascal  (c) erg  (d) watt  (e) joule.

Last Answer : Answer : d

The unit of energy in S.I. units is  (a) watt  (b) joule  (c) joule/s  (d) joule/m  (e) joule m.

Description : The unit of energy in S.I. units is  (a) watt  (b) joule  (c) joule/s  (d) joule/m  (e) joule m.

Last Answer : Answer : b

The steam engine was invented by (1) James Watt (2) James Prescott Joule (3) New Commen (4) Isaac Newton

Description : The steam engine was invented by (1) James Watt (2) James Prescott Joule (3) New Commen (4) Isaac Newton

Last Answer : (1) James Watt

Which of the following is NOT an SI unit of measure? w) watt x) newton y) joule z) erg e) second

Description : Which of the following is NOT an SI unit of measure? w) watt x) newton y) joule z) erg e) second

Last Answer : ANSWER: Z -- ERG

Unit of Power is_____________. A. Watt B. Joule C. Ampere D. Coulomb

Description : Unit of Power is_____________. A. Watt B. Joule C. Ampere D. Coulomb 

Last Answer : Unit of Power is Watt. 

The sound intensity received from the nearby jet plane is 12.6 µW/m2 and that from another jet plane some distance away is 0.45 µW/m2 . Find the relative loudness of the two. A. 14.0 dB B. 14.5dB C. 12.5 D. 14.5

Description : The sound intensity received from the nearby jet plane is 12.6 µW/m2 and that from another jet plane some distance away is 0.45 µW/m2 . Find the relative loudness of the two. A. 14.0 dB B. 14.5dB C. 12.5 D. 14.5

Last Answer : B. 14.5dB

When attempting to measure a current of less than 10 amps with the device shown, the range switch should be set to ___________. EL-0047 A. 500 MA B. 10 MA / AMPS with leads in the (-COMMON) and (+) jacks C. 10 MA / AMPS with leads in the (-COMMON) and (+10 A) jacks D. 10 MA / AMPS with leads in the (-10 A) and (+10 A) jacks

Description : When attempting to measure a current of less than 10 amps with the device shown, the range switch should be set to ___________. EL-0047 A. 500 MA B. 10 MA / AMPS with leads in the (-COMMON) and (+) jacks C. 10 MA ... ) and (+10 A) jacks D. 10 MA / AMPS with leads in the (-10 A) and (+10 A) jacks

Last Answer : Answer: D

When attempting to measure AC current with the device shown and you are unsure of the range, the range switch should be set to __________. EL-0047 A. 10 MA / AMPS with leads in the (-10 A) and (+10 A) jacks B. 10 MA / AMPS with leads in the (-COMMON) and (+) jacks C. 10 MA / AMPS with leads in the (-COMMON) and (+10 A) jacks D. unable to accurately measure AC current with this device as illustrated

Description : When attempting to measure AC current with the device shown and you are unsure of the range, the range switch should be set to __________. EL-0047 A. 10 MA / AMPS with leads in the (-10 A) and ... (-COMMON) and (+10 A) jacks D. unable to accurately measure AC current with this device as illustrated

Last Answer : Answer: D

If reading the AC voltage from a typical wall outlet, the range switch of the device illustrated should be set to ___________. EL-0047 A. 1,000 V B. 250 V C. R X 10,000 D. 10 ma/amps

Description : If reading the AC voltage from a typical wall outlet, the range switch of the device illustrated should be set to ___________. EL-0047 A. 1,000 V B. 250 V C. R X 10,000 D. 10 ma/amps

Last Answer : Answer: B

How many amps does a 1500 watt heater need?

Description : How many amps does a 1500 watt heater need?

Last Answer : Feel Free to Answer

The rate of energy transfer from a higher temperature to a lower temperature is measured in a) kcal b) Watt c) Watts per second d) none of the above.

Description : The rate of energy transfer from a higher temperature to a lower temperature is measured in a) kcal b) Watt c) Watts per second d) none of the above.

Last Answer : b) Watt

A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC+ve polarity, and a ROL:of 180mm per min. What would be the arc energy? a) Insufficient information given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm

Description : A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC ... given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm

Last Answer : d) 2.0 kJ/mm

When reading AC current with the multimeter shown in the illustration and you are unsure of the range, the range switch should be set to ___________. EL-0047 A. 10 MA/ 10 AMP with leads in the (-10 A) and (+10 A) jacks B. 10 MA/ 10 AMP with leads in the (-COMMON) and (+) jacks C. 10 MA/ 10 AMP with leads in the (-COMMON) and (+10 A) jacks D. unable to measure AC current with this multimeter

Description : When reading AC current with the multimeter shown in the illustration and you are unsure of the range, the range switch should be set to ___________. EL-0047 A. 10 MA/ 10 AMP with leads in the (-10 A ... leads in the (-COMMON) and (+10 A) jacks D. unable to measure AC current with this multimeter

Last Answer : Answer: D

If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω

Description : If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω

Last Answer : 500Ω

Op-amp can provide maximum output current of A. 25 mA B. 30 mA C. 35 mA D. 40 mA

Description : Op-amp can provide maximum output current of A. 25 mAB. 30 mA C. 35 mA D. 40 mA

Last Answer :  25 mA

Calculate the resistance of shunt required to make a milliammeter which gives maximum deflection for a current of 15 mA and which has a resistance of 5 Ω; read up to 10 Amp.

Description : Calculate the resistance of shunt required to make a milliammeter which gives maximum deflection for a current of 15 mA and which has a resistance of 5 Ω; read up to 10 Amp.

Last Answer : Answer :

What is the phase delay of an 800 Hz voice signal if the phase shift is 15 degrees? A. 1.25 µsec B. 52 µsec C. 83.33 µsec D. 26 µsec

Description : What is the phase delay of an 800 Hz voice signal if the phase shift is 15 degrees? A. 1.25 µsec B. 52 µsec C. 83.33 µsec D. 26 µsec

Last Answer : B. 52 µsec

The access time of ROM using bipolar transistors is about (A) 1 sec (B) 1 msec (C) 1 µsec (D) 1 nsec.

Description : The access time of ROM using bipolar transistors is about (A) 1 sec (B) 1 msec (C) 1 µsec (D) 1 nsec.

Last Answer : Ans: C The access time of ROM using bipolar transistors is about 1 µ sec.

Cable attenuation is usually expressed in terms of ∙ A. loss per foot ∙ B. dB/km ∙ C. intensity per mile ∙ D. voltage drop per inch

Description : Cable attenuation is usually expressed in terms of ∙ A. loss per foot ∙ B. dB/km ∙ C. intensity per mile ∙ D. voltage drop per inch

Last Answer : . dB/km

The _____ is equal to the number of electrons emitted per second times the electron charge ∙ a. Intensity ∙ b. Optical power ∙ c. Photocurrent ∙ d. Responsitivity

Description : The _____ is equal to the number of electrons emitted per second times the electron charge ∙ a. Intensity ∙ b. Optical power ∙ c. Photocurrent ∙ d. Responsitivity

Last Answer : c. Photocurrent

Cable attenuation is usually expressed in terms of ∙ a. Loss per foot ∙ b. dB/km ∙ c. intensity per mile ∙ d. voltage drop per inch

Description : Cable attenuation is usually expressed in terms of ∙ a. Loss per foot ∙ b. dB/km ∙ c. intensity per mile ∙ d. voltage drop per inch

Last Answer : ∙ b. dB/km

The loss in single-mode fiber-optic cable due to the glass is about: a. 40 dB per km b. 4 db per km c. 0.4 dB per km d. zero loss

Description : The loss in single-mode fiber-optic cable due to the glass is about: a. 40 dB per km b. 4 db per km c. 0.4 dB per km d. zero loss

Last Answer : c. 0.4 dB per km

How many 1500 watt heaters can you run on a 20 amp circuit?

Description : How many 1500 watt heaters can you run on a 20 amp circuit?

Last Answer : As you did not specify the voltage of the circuit, I will I will assume your heaters are 110 volt portable heaters not 220 volt baseboard heaters.Each heater will draw 1500 watts / 110 volts = 13.64 ... more than half of the 20 ampere rating of the circuit, you can only run one of these heater.