Description : If h is the loss due to friction in a pipe. Total losses in strainer and bends may be taken as (A) 0.01 h (B) 0.45 h (C) 0.20 h (D) 0.25 h
Last Answer : Answer: Option D
Description : In case of flow through parallel pipes, (A) The head loss for all the pipes is same (B) The total discharge is equal to the sum of discharges in the various pipes (C) The total head loss is the sum of head losses in the various pipes (D) Both (A) and (B)
Description : In parallel pipe problems, the (A) Head loss is the same through each pipe (B) Discharge is the same through all the pipes (C) Total head loss is equal to the sum of the head losses through each pipe (D) None of these
Last Answer : (A) Head loss is the same through each pipe
Description : The minimum design speed for hairpin bends in hill roads is taken as (A) 20 kmph (B) 30 kmph (C) 40 kmph (D) 50 kmph
Last Answer : Answer: Option A
Description : When a number of hair pin bends are introduced, a minimum intervening distance in between is kept (A) 20 m (B) 40 m (C) 60 m (D) 100 m
Last Answer : Answer: Option C
Description : A pressure conduit laid underground, may not be subjected to (A) Internal pressure of water (B) Pressure due to external load (C) Longitudinal temperature stress (D) Longitudinal stresses due to unbalanced pressure to bends
Last Answer : (C) Longitudinal temperature stress
Description : Total mechanical losses ( frictional losses , pumping loss in intake and exhaust and power accessories) will amount to a.10-20 % ihp b.2-10 % ihp c.20-30 % ihp d.30 -50 % ihp
Last Answer : a.10-20 % ihp
Description : The armature of a dc machine is laminated to reduce: (A) Eddy current loss (B) Hysteresis loss (C) copper losses (D) friction and windage losses
Last Answer : Ans: A Thinner the laminations, greater is the resistance offered to the induced e.m.f., smaller the current and hence lesser the I2R loss in the core.
Description : 14. When the pipes are in series, the total head loss is equal to the sum of the head loss in each pipe A) Yes B) No
Last Answer : A
Description : In case of Venturimeter, friction losses are about __________ percent of maximum velocity head. (A) 2 (B) 8 (C) 12 (D) 20
Last Answer : (A) 2
Description : While designing hair pin bends on highways, the minimum (A) Designed speed is 20 km/hour (B) Gradient is 1 in 40 (C) Gradient is 1 in 200 (D) All the above
Description : A 10 cm dia steam pipe, carrying steam at 180°C, is covered with an insulation (conductivity = 0.6 W/m.°C). It losses heat to the surroundings at 30°C. Assume a heat transfer co-efficient of 0 ... that of the un-insulated steam pipe (D) Less than the steam pipe with 5 cms insulation
Last Answer : (B) Less than that of the un-insulated steam pipe
Description : A tree breaks due to storm and the broken part bends so that the top of the tree touches the ground making an angle 30° with it. The distance between the foot of the tree to the point where the top touches the ground is 8 m. Find the height of the tree. -Maths 9th
Last Answer : The broken part bends so that the top of the tree touches the ground making an angle 30 °. The distance between the foot of the tree to the point where the top touches the ground is 8 m. Original height of ... After rationalising Now we have , A`BC = AB + BC Take LCM So , original height of tree is
Description : The loss of head due to viscosity for laminar flow in pipes is (where d = Diameter of pipe, l = Length of pipe, v w = Specific weight of the flowing liquid) (A) 4 (B) 8 (C) 16 (D) 32
Description : The term power budgeting refers to ∙ A. the cost of cable, connectors, equipment and installation ∙ B. the loss of power due to defective components ∙ C. the total power available minus the attenuation losses ∙ D. the comparative costs of fiber and copper installations
Last Answer : C. the total power available minus the attenuation losses
Description : Pick up the correct statement from the following: A. The sewer pipes of sizes less than 0.4 m diameter are designed as running full at maximum discharge B. The sewer pipes of sizes greater than 0.4 m ... discharge C. The minimum design velocity of sewer pipes is taken as 0.8 m/sec D. All the above
Last Answer : ANS: D
Description : Which of the following losses of pre-stress occurs only in pre-tensioning and not in posttensioning? (A) Elastic shortening of concrete (B) Shrinkage of concrete (C) Creep of concrete (D) Loss due to friction
Description : From distribution main of 50 mm size, number of service pipes of 15 mm size can be taken off are ------ a) 6 b)10 c) 12 e):20*
Last Answer : e):20*
Description : The strainer type tube well, is unsuitable for (A) Coarse gravels (B) Fine sandy strata (C) Clean gravels (D) None of these
Last Answer : (B) Fine sandy strata
Description : Abyssinian tube well is a special type of (A) Slotted type wells (B) Cavity type wells (C) Strainer type well (D) None of these
Last Answer : (C) Strainer type well
Description : A strainer type well sunk through three previous layers intervened by three impervious aquicludes, draws water from (A) Top most pervious layer (B) Central pervious layer (C) Lowest pervious layer (D) All the pervious layer
Last Answer : (D) All the pervious layers
Description : The most important and widely used tube well in India, is (A) Strainer well (B) Cavity well (C) Slotted well (D) Perforated pipe well
Last Answer : (A) Strainer well
Description : Pick up the incorrect statement from the following: (A) The flow in strainer type wells is radial (B) The flow in cavity type wells in spherical (C) In strainer type wells, area of flow ... pipe (D) In cavity type wells, area of flow depends upon the size of the cavity
Last Answer : (C) In strainer type wells, area of flow depends upon the length of the strainer pipe
Description : Shrouding' is essentially provided in (A) Strainer type wells (B) Cavity type wells (C) Slotted type well (D) All the above
Last Answer : (C) Slotted type well
Description : Shrouding is provided in (A) Cavity type tube wells (B) Slotted type tube wells (C) Strainer type tube wells (D) Perforated type tube wells
Last Answer : Answer: Option B
Description : Which of the following statement(s) is/are true concerning protein/amino acid metabolism in man? a. The major source of amino acids is breakdown of circulating proteins b. The recommended daily ... balance refers to a decrease in nitrogen taken into the body versus the amount of nitrogen lost
Last Answer : Answer: b, d About 15% of the total body weight is made up of proteins, about half of which are intracellular and half extracellular. In man and other animals, dietary protein is the source of ... is exceeded by the amount of nitrogen lost in the urine, stool, skin, wounds, and fistula drainage
Description : According to Darcy's formula, the loss of head due to friction in the pipe is (where f = Darcy's coefficient, l = Length of pipe, v = Velocity of liquid in pipe, and d = Diameter of pipe) (A) flv²/2gd (B) flv²/gd (C) 3flv²/2gd (D) 4flv²/2gd
Description : The loss of head due to friction in a pipe of uniform diameter in which a viscous flow is taking place, is (where RN = Reynold number) (A) 1/RN (B) 4/RN (C) 16/RN (D) 64/RN
Description : Pre-stress loss due to friction occurs (A) Only in post-tensioned beams (B) Only in pre-tensioned beams (C) In both post-tensioned and pre-tensioned beams (D) None of the above
Description : Which one of the following statements is not correct with respect to PSC beams? (a) Loss due to shrinkage is proportional to water-cement ratio used in concrete (b) Loss due to creep is ... to the modulus of elasticity of concrete (d) Loss due to friction occurs in post tensioned concrete members
Last Answer : (c) Loss due to elastic deformation is directly proportionally to the modulus of elasticity of concrete
Description : A pipe of I.D. 4 m is bifurcated into two pipes of I.D. 2 m each. If the average velocity of water flowing through the main pipe is 5 m/sec, the average velocity through the bifurcated pipes is (A) 20 m/sec (B) 10 m/sec (C) 5 √2 m/sec (D) 5 m/sec
Last Answer : (B) 10 m/sec
Description : A block of weight 20 kg slides with an initial velocity of 2 m sec down an inclined plane on to a spring of stiffness 10 kg/cm. If the co--efficient of friction is 0.2, angle ? = 30 the ratio of ... be a.More than one b.One c.Less than one d.Depends on the stiffness of spring e.None of the above
Last Answer : a. More than one
Description : The maximum pressure to which cast iron pipes may be subjected to, is (A) 3 kg/cm2 (B) 5 kg/cm2 (C) 7 kg/cm2 (D) 10 kg/cm
Last Answer : (C) 7 kg/cm
Description : Which of the following pipe bends will incur the largest head loss? (A) U-bend (B) 30° bend (C) 45° bend (D) 90° bend
Last Answer : (A) U-bend
Description : Microbend loss is caused by microscopic bends of the fiber axis. List three sources of microbend loss.
Last Answer : Uneven coating applications, improper cabling procedures, and external force.
Description : Band loss is ∙ a. A reduction in transmitter power caused by earth’s surface curvature ∙ b. A reduction in strength of the signal caused by folded dipole bends ∙ c. An attenuation increase caused by bends radiating from the side of the fiber ∙ d. All of these
Last Answer : c. An attenuation increase caused by bends radiating from the side of the fiber
Description : The efficiency of power transmission through pipe is (where H = Total supply head, and hf = Head lost due to friction in the pipe) (A) (H - hf )/H (B) H/(H - hf ) (C) (H + hf )/H (D) H/(H + hf )
Description : The power transmitted through the nozzle is maximum when the head lost due to friction in the pipe is __________ of the total supply head. (A) One-half (B) One-third (C) Two-third (D) None of these
Description : The power transmitted through the pipe is maximum when the head lost due to friction is equal to (A) One-fourth of the total supply head (B) One-third of the total supply head (C) One-half of the total supply head (D) Two-third of the total supply head
Description : Consider the following statements: The total head against which a pump has to work must include, besides any other items, 1. the suction lift. 2. the delivery head. 3. the head lost due to friction at entrance in the rising main. 4. the ... 2 & 3 only (b) 2 & 3 only (c) 1, 2, 3 & 4 (d) 3 & 4 only
Last Answer : (c) 1, 2, 3 & 4
Description : Pipes P, Q and R which fill the tank together in 12 hours are opened for 2hours after which pipe R was closed. Find the number of hours taken by pipe R to fill the tank if the remaining tank is filled in 14 hours. A) 16 B) 14 C) 20 D) 42
Last Answer : D 1/P + 1/Q + 1/R = 1/12 Now given that first all open for 2hours, then R closed and P+Q completes in 14 hours, so (1/P + 1/Q + 1/R) *2 + (1/P + 1/Q)*14 = 1 Put 1/P + 1/Q = 1/12 – 1/R (1/12 – 1/R + 1/R) *2 + (1/12 – 1/R)*14 = 1 1/6+ 14/12 – 14/R = 1 Solve, R = 42
Description : Pick up the incorrect statement from the following: (A) No deduction is made for the volume occupied by reinforcement (B) No deduction is made for the openings upto 0.1 sq.m (C) No deduction is made for volumes occupied by pipes, not exceeding 100 sq.cm in crosssection (D) None of these
Last Answer : (D) None of these
Description : During ageing of fluid carrying pipes, the (A) Pipe becomes smoother with use (B) Friction factor increases linearly with time (C) Absolute roughness decreases with time (D) Absolute roughness increases linearly with time
Last Answer : (D) Absolute roughness increases linearly with time
Description : In case of hydraulically smooth pipe, the resistance to flow depends only on the Reynolds number, whereas for a hydraulically rough pipe, the resistance to flow is governed by the relative roughness. Two pipes are said ... co-efficient for flows at equal Reynold number (D) All (A), (B) & (C)
Last Answer : (C) Friction co-efficient for flows at equal Reynold number
Description : Consider two pipes of same length and diameter through which water is passed at the same velocity. The friction factor for rough pipe is f1 and that for smooth pipe is f2 . Pick out the correct statement. (A) f1 = f2 (B) f1 < f2 (C) f1 > f2 (D) Data not sufficient to relate f1 & f2
Last Answer : (C) f1 > f2
Description : In the complete turbulence zone (in rough pipes), the (A) Rough and smooth pipes have the same friction factor (B) Laminar film covers the roughness projections (C) Friction factor depends upon NRe only (D) Friction factor is independent of the relative roughness
Last Answer : (D) Friction factor is independent of the relative roughness
Description : A 50 kilogram ice skater glides across the ice in a straight line at 7 meters per second. If she bends down and scoops up a 20 kilogram child standing on the ice, what will be the final speed of the skater ... w) 1 meter per second x) 3 meters per second y) 5 meters per second z) 7 meters per second
Last Answer : ANSWER: Y -- 5 METERS PER SECOND
Description : To pump water from a water reservoir 3 m deep and maximum water level at 135 m, a pump is installed to lift water up to R.L. 175 m at a constant rate of 36,00,000 litres per hour. If the length of the ... the water horse power of the pump is (A) 400 (B) 450 (C) 500 (D) 600
Last Answer : (D) 600
Description : In case of end to end connection of two or more pipes in series, the __________ each pipe. (A) Same rate of flow passes through (B) Head loss is same through (C) Rate of flow in each pipe is proportional to the length of (D) Total flow rate is the sum of flow rate in
Last Answer : (A) Same rate of flow passes through
Description : Partial bearing is preferred over journal bearing. a) True b) No c) More friction losses d) Can’t be determined
Last Answer : a) True