The length of the lap in a compression member is kept greater than bar diameter x (Permissible stress in bar / Five times the bond stress) or (A) 12 bar diameters (B) 18 bar diameters (C) 24 bar diameters (D) 30 bar diameters

The length of the lap in a compression member is kept greater than bar diameter x (Permissible
stress in bar / Five times the bond stress) or
(A) 12 bar diameters
(B) 18 bar diameters
(C) 24 bar diameters
(D) 30 bar diameters
by

1 Answer

Answer :

Answer: Option C
by

Related questions

The length of lap in tension reinforcement should not be less than the bar diameter × (actual tension / four times the permissible average bond stress) if it is more than (A) 18 bar diameters (B) 24 bar diameters (C) 30 bar diameters (D) 36 bar diameters

Description : The length of lap in tension reinforcement should not be less than the bar diameter × (actual tension / four times the permissible average bond stress) if it is more than (A) 18 bar diameters (B) 24 bar diameters (C) 30 bar diameters (D) 36 bar diameters

Last Answer : Answer: Option C

The development length of bars in compression is taken as [ A ] 30 times bar diameter [ B ] 40 times bar diameter [ C ] 50 times bar diameter [ D ] 12 times bar diameter

Description : The development length of bars in compression is taken as [ A ] 30 times bar diameter [ B ] 40 times bar diameter [ C ] 50 times bar diameter [ D ] 12 times bar diameter

Last Answer : [ A ] 30 times bar diameter

The development length of bars in compression is taken as [ A ] 30 times bar diameter [ B ] 40 times bar diameter [ C ] 50 times bar diameter [ D ] 12 times bar diameter

Description : The development length of bars in compression is taken as [ A ] 30 times bar diameter [ B ] 40 times bar diameter [ C ] 50 times bar diameter [ D ] 12 times bar diameter

Last Answer : [ A ] 30 times bar diameter

End anchorage of bars is taken as the greater of [ A ] Effective depth or 12 times the diameter of bar [ B ] Effective depth or 16 times the diameter of bar [ C ] Effective depth of 24 times the diameter of bar [ D ] Effective depth of 48 times the diameter of bar

Description : End anchorage of bars is taken as the greater of [ A ] Effective depth or 12 times the diameter of bar [ B ] Effective depth or 16 times the diameter of bar [ C ] Effective depth of 24 times the diameter of bar [ D ] Effective depth of 48 times the diameter of bar

Last Answer : [ A ] Effective depth or 12 times the diameter of bar

End anchorage of bars is taken as the greater of [ A ] Effective depth or 12 times the diameter of bar [ B ] Effective depth or 16 times the diameter of bar [ C ] Effective depth of 24 times the diameter of bar [ D ] Effective depth of 48 times the diameter of bar

Description : End anchorage of bars is taken as the greater of [ A ] Effective depth or 12 times the diameter of bar [ B ] Effective depth or 16 times the diameter of bar [ C ] Effective depth of 24 times the diameter of bar [ D ] Effective depth of 48 times the diameter of bar

Last Answer : [ A ] Effective depth or 12 times the diameter of bar

The average permissible stress in bond for plain bars in tension is (A) Increased by 10% for bars in compression (B) Increased by 25% for bars in compression (C) Decreased by 10% for bars in compression (D) Decreased by 25% for bars in compression

Description : The average permissible stress in bond for plain bars in tension is (A) Increased by 10% for bars in compression (B) Increased by 25% for bars in compression (C) Decreased by 10% for bars in compression (D) Decreased by 25% for bars in compression

Last Answer : Answer: Option B

If Sb, is the average bond stress on a bar of diameter subjected to maximum stress , the length of the embedment is given by (A) l = dt/Sb (B) l = dt/2Sb (C) l = dt/3Sb (D) l = dt/4S

Description : If Sb, is the average bond stress on a bar of diameter subjected to maximum stress , the length of the embedment is given by (A) l = dt/Sb (B) l = dt/2Sb (C) l = dt/3Sb (D) l = dt/4S

Last Answer : Answer: Option D Answer: Option D

If d is the diameter of a bar, ft is allowable tensile stress and fb, is allowable bond stress, the bond length is given by (A) ft .d/4fb (B) ( /4). (ft .d/fb) (C) ft .d²/fb (D) ( /4). (ft .d 3 /fb)

Description : If d is the diameter of a bar, ft is allowable tensile stress and fb, is allowable bond stress, the bond length is given by (A) ft .d/4fb (B) ( /4). (ft .d/fb) (C) ft .d²/fb (D) ( /4). (ft .d 3 /fb)

Last Answer : Answer: Option A

Ratio of permissible stress in direct compression and bending compression is (A) Less than 1 (B) Between 1 and 1.5 (C) Between 1.5 and 2.0 (D) Greater

Description : Ratio of permissible stress in direct compression and bending compression is (A) Less than 1 (B) Between 1 and 1.5 (C) Between 1.5 and 2.0 (D) Greater than 2

Last Answer : Answer: Option A

In doubly reinforced rectangular beam, the allowatte stress in compression steel is___________the permissible stross intension insteel. (a) Greater than (b) Less than (c) Equal to (d) All of these

Description : In doubly reinforced rectangular beam, the allowatte stress in compression steel is___________the permissible stross intension insteel. (a) Greater than (b) Less than (c) Equal to (d) All of these

Last Answer : (b) Less than

If the bond stress developed in a reinforced concrete beam is more than permissible value, it can be brought down by. (a) Increasing the depth of beam (b) Increasing the number of bars. (c) Decreasing the diameter of the bars (d) All of these

Description : If the bond stress developed in a reinforced concrete beam is more than permissible value, it can be brought down by. (a) Increasing the depth of beam (b) Increasing the number of bars. (c) Decreasing the diameter of the bars (d) All of these

Last Answer : (d) All of these

If tensile stress of a steel rod of diameter is 1400 kg/cm2 and bond stress is 6 kg/cm2 , the required bond length of the rod is (A) 30 D (B) 39 D (C) 50 D (D) 59 D

Description : If tensile stress of a steel rod of diameter is 1400 kg/cm2 and bond stress is 6 kg/cm2 , the required bond length of the rod is (A) 30 D (B) 39 D (C) 50 D (D) 59 D

Last Answer : (D) 59 D

In working stress design, permissible bond stress in the case of deformed bars is more than that in plain bars by (A) 10 % (B) 20 % (C) 30 % (D) 40 %

Description : In working stress design, permissible bond stress in the case of deformed bars is more than that in plain bars by (A) 10 % (B) 20 % (C) 30 % (D) 40 %

Last Answer : (D) 40 %

Bottom bars under the columns are extended into the interior of the footing slab to a distance greater than (A) 42 diameters from the centre of the column (B) 42 diameters from the inner edge of the column (C) 42 diameters from the outer edge of the column (D) 24 diameters from the centre of the column

Description : Bottom bars under the columns are extended into the interior of the footing slab to a distance greater than (A) 42 diameters from the centre of the column (B) 42 diameters from the inner edge of ... ) 42 diameters from the outer edge of the column (D) 24 diameters from the centre of the column

Last Answer : Answer: Option C

A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum permissible angle of twist in the shaft is 1o. The inner diameter of the shaft is 0.7 times the outer diameter. The modulus of rigidity is 80 GPa. The outside diameter (in mm) of the shaft is _______. (a) 43 to 45 (b) 50to 60 (c) 70 to 80 (d) 85 to 100

Description : A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum permissible angle of twist in the shaft is 1o. The inner diameter of the shaft is 0.7 times the outer diameter. The modulus of ... shaft is _______. (a) 43 to 45 (b) 50to 60 (c) 70 to 80 (d) 85 to 100

Last Answer : (a) 43 to 45

The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose ends are hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm2 , the permissible maximum crippling load will be (A) 1.288 tonnes (B) 12.88 (C) 128.8 tonnes (D) 288.0

Description : The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose ends are hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm2 , the permissible maximum crippling load will be (A) 1.288 tonnes (B) 12.88 (C) 128.8 tonnes (D) 288.0

Last Answer : (B) 12.88

As per IS: 1139, permissible stress in compression steel reinforcement for High Yield strength deformed bars is [ A ] 140 N/mm2 [ B ] 190 N/mm2 [ C ] 230 N/mm2 [ D ] 415 N/mm2

Description : As per IS: 1139, permissible stress in compression steel reinforcement for High Yield strength deformed bars is [ A ] 140 N/mm2 [ B ] 190 N/mm2 [ C ] 230 N/mm2 [ D ] 415 N/mm2

Last Answer : [ B ] 190 N/mm2

If the average bending stress is 6 kg/cm2 for M 150 grade concrete, the length of embedment of a bar of diameter d according to I.S. 456 specifications, is (A) 28 d (B) 38 d (C) 48 d (D) 58 d

Description : If the average bending stress is 6 kg/cm2 for M 150 grade concrete, the length of embedment of a bar of diameter d according to I.S. 456 specifications, is (A) 28 d (B) 38 d (C) 48 d (D) 58 d

Last Answer : Answer: Option D

Minimum pitch of transverse reinforcement in a column is (A) The least lateral dimension of the member (B) Sixteen times the smallest diameter of longitudinal reinforcement bar to be tied (C) Forty-eight times the diameter of transverse reinforcement (D) Lesser of the above three values

Description : Minimum pitch of transverse reinforcement in a column is (A) The least lateral dimension of the member (B) Sixteen times the smallest diameter of longitudinal reinforcement bar to be tied (C) Forty-eight times the diameter of transverse reinforcement (D) Lesser of the above three values

Last Answer : Answer: Option D

As per IS :456-1978, the permissible value of bond – stress for M15 grade of concrete is (a) 0.5 N/mm2 (b) 1 N/mm2 (c) 1.5 N/mm2 (d) 2 N/mm2

Description : As per IS :456-1978, the permissible value of bond – stress for M15 grade of concrete is (a) 0.5 N/mm2 (b) 1 N/mm2 (c) 1.5 N/mm2 (d) 2 N/mm2

Last Answer : (b) 1 N/mm2

As per IS: 456, permissible bond stress for plain bars in tension, in working stress method, where M20, is the grade of concrete [ A ] 0.6 N/mm2 [ B ] 0.8 N/mm2 [ C ] 1.0 N/mm2 [ D ] 1.2 N/mm2

Description : As per IS: 456, permissible bond stress for plain bars in tension, in working stress method, where M20, is the grade of concrete [ A ] 0.6 N/mm2 [ B ] 0.8 N/mm2 [ C ] 1.0 N/mm2 [ D ] 1.2 N/mm2

Last Answer : [ B ] 0.8 N/mm2

The radius of a bar bend to form a hook, should not be less than (A) Twice the diameter (B) Thrice the diameter (C) Four times the diameter (D) Five times the diameter

Description : The radius of a bar bend to form a hook, should not be less than (A) Twice the diameter (B) Thrice the diameter (C) Four times the diameter (D) Five times the diameter

Last Answer : Answer: Option A

Lapped splices in tensile reinforcement are generally not used for bars of size larger than (A) 18 mm diameter (B) 24 mm diameter (C) 30 mm diameter (D) 36 mm diameter

Description : Lapped splices in tensile reinforcement are generally not used for bars of size larger than (A) 18 mm diameter (B) 24 mm diameter (C) 30 mm diameter (D) 36 mm diameter

Last Answer : Answer: Option D

The diameter of the column head support a flat slab, is generally kept (A) 0.25 times the span length (B) 0.25 times the diameter of the column (C) 4.0 cm larger than the diameter of the column (D) 5.0 cm larger than the diameter of the column

Description : The diameter of the column head support a flat slab, is generally kept (A) 0.25 times the span length (B) 0.25 times the diameter of the column (C) 4.0 cm larger than the diameter of the column (D) 5.0 cm larger than the diameter of the column

Last Answer : Option A

If d is the diameter of the pipe, p is the total internal pressure, f is the permissible tensile stress and n is the effective of the joint, the thickness t of metal pipe, is (A) n (pd/2f) (B) (1/n) (pd/2f) (C) (1/n) (pd/3f) (D) (1/n) (pf/d

Description : If d is the diameter of the pipe, p is the total internal pressure, f is the permissible tensile stress  and n is the effective of the joint, the thickness t of metal pipe, is  (A) n (pd/2f)  (B) (1/n) (pd/2f)  (C) (1/n) (pd/3f)  (D) (1/n) (pf/d

Last Answer : (B) (1/n) (pd/2f) 

Regarding the working stress design of under reinforced concrete section, (a) The neutral axis depth will be greater than that of a balanced section. (b) The stress in steel intension will reach its maximum permissible value first. (c) The moment of resistance will be less than that of the balanced section. (d) The concrete on the tension side is also be considered for calculating the moment of resistance of the section.

Description : Regarding the working stress design of under reinforced concrete section, (a) The neutral axis depth will be greater than that of a balanced section. (b) The stress in steel intension will reach ... on the tension side is also be considered for calculating the moment of resistance of the section.

Last Answer : both b&c

If the depth of actual neutral axis is greater than the depth of critical neutral axis, then [ A ] Concrete attains its permissible stress earlier [ B ] Steel attains its permissible stress earlier [ C ] Both concrete and steel reaches its permissible stresses simultaneously [ D ] None of the above

Description : If the depth of actual neutral axis is greater than the depth of critical neutral axis, then [ A ] Concrete attains its permissible stress earlier [ B ] Steel attains its permissible stress earlier [ C ] Both concrete and steel reaches its permissible stresses simultaneously [ D ] None of the above

Last Answer : [ A ] Concrete attains its permissible stress earlier

The diameter of earth is 12,757 kilometers the diameter of satum is 120,664 the diameters of uranus is 51,499 is the sum of these three plantes diameters more or less than jupiter diameter of 142,804 kilometers by how much answer?

Description : The diameter of earth is 12,757 kilometers the diameter of satum is 120,664 the diameters of uranus is 51,499 is the sum of these three plantes diameters more or less than jupiter diameter of 142,804 kilometers by how much answer?

Last Answer : 2

A simply supported wooden beam 150 cm long and having a cross section 16 cm × 24 cm carries a concentrated load, at the centre. If the permissible stress ft = 75 kg/cm2 and fs= 10 kg/cm2 the safe load is (A) 3025 kg (B) 3050 kg (C) 3075 kg (D) 3100 kg

Description : A simply supported wooden beam 150 cm long and having a cross section 16 cm × 24 cm carries a  concentrated load, at the centre. If the permissible stress ft = 75 kg/cm2  and fs= 10 kg/cm2  the safe  load is  (A) 3025 kg  (B) 3050 kg  (C) 3075 kg  (D) 3100 kg 

Last Answer : (C) 3075 kg 

The bond stress for plain bars in compression is more than that for bars in tension by [ A ] 25% [ B ] 40% [ C ] 60% [ D ] 50%

Description : The bond stress for plain bars in compression is more than that for bars in tension by [ A ] 25% [ B ] 40% [ C ] 60% [ D ] 50%

Last Answer : [ A ] 25%

Minimum spacing between horizontal parallel reinforcement of the same size should not be less than (A) One diameter (B) 2.5 diameters (C) 3 diameters (D) 3.5 diameters

Description : Minimum spacing between horizontal parallel reinforcement of the same size should not be less than (A) One diameter (B) 2.5 diameters (C) 3 diameters (D) 3.5 diameters

Last Answer : Answer: Option A

The diameter of pipes in bath rooms and lavatories in domestic water supply, is (A) 6 mm (B) 12 mm (C) 18 mm (D) 24 mm

Description : The diameter of pipes in bath rooms and lavatories in domestic water supply, is (A) 6 mm (B) 12 mm (C) 18 mm (D) 24 mm

Last Answer : (B) 12 mm

According to IS: 456 -2000, the spacing of links in a Column should be less than [ A ] 16 x diameter of smallest longitudinal bar [ B ] 24 x diameter of smallest longitudinal bar [ C ] 48 x diameter of smallest longitudinal bar [ D ] 48 x diameter of greatest longitudinal bar

Description : According to IS: 456 -2000, the spacing of links in a Column should be less than [ A ] 16 x diameter of smallest longitudinal bar [ B ] 24 x diameter of smallest longitudinal bar [ C ] 48 x diameter of smallest longitudinal bar [ D ] 48 x diameter of greatest longitudinal bar

Last Answer : [ A ] 16 x diameter of smallest longitudinal bar

18.The total extension of a taper rod of length ‘L’ and end diameters ‘D1’ and ‘D2’, subjected to a load (P), is given of a. 4PL/ΠE. D1D2 b. 3PL/ΠE. D1D2 c. 2PL/ΠE. D1D2 d. PL/ΠE.D1D2 Where E=Young’s modulus of elasticity

Description : 18.The total extension of a taper rod of length ‘L’ and end diameters ‘D1’ and ‘D2’, subjected to a load (P), is given of a. 4PL/ΠE. D1D2 b. 3PL/ΠE. D1D2 c. 2PL/ΠE. D1D2 d. PL/ΠE.D1D2 Where E=Young’s modulus of elasticity

Last Answer : a. 4PL/ΠE. D1D2

The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose endsare hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm2, the permissible maximumcrippling load will be (a) 1.288 tonnes (b) 12.88 (c) 128.8 tonnes (d) 288.0

Description : The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose endsare hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm2, the permissible maximumcrippling load will be (a) 1.288 tonnes (b) 12.88 (c) 128.8 tonnes (d) 288.0

Last Answer : (b) 12.88

The length of the straight portion of a bar beyond the end of the hook, should be at least (A) Twice the diameter (B) Thrice the diameter (C) Four times the diameter (D) Seven times the diameter

Description : The length of the straight portion of a bar beyond the end of the hook, should be at least (A) Twice the diameter (B) Thrice the diameter (C) Four times the diameter (D) Seven times the diameter

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) All pipes and fittings are classified according to their diameters (B) The diameter of the pipes is the nominal diameter of internal bore (C) All pipes are measured along the centre line of the pipes in metres (D) All the above

Description : Pick up the correct statement from the following: (A) All pipes and fittings are classified according to their diameters (B) The diameter of the pipes is the nominal diameter of internal bore (C) All pipes are measured along the centre line of the pipes in metres (D) All the above

Last Answer : (D) All the above

According to IS: 4561978, the column or the strut is the member whose effective length is greater than (A) The least lateral dimension (B) 2 times the least lateral dimension (C) 3 times the least lateral dimension (D) 4 times the least lateral dimension

Description : According to IS: 4561978, the column or the strut is the member whose effective length is greater than (A) The least lateral dimension (B) 2 times the least lateral dimension (C) 3 times the least lateral dimension (D) 4 times the least lateral dimension

Last Answer : Answer: Option C

The cross sections of the beams of equal length are a circle and a square whose permissible bending stress is same under same maximum bending. The ratio of their flexural weights is, (A) 1.118 (B) 1.338 (C) 1.228 (D) 1.108

Description : The cross sections of the beams of equal length are a circle and a square whose permissible bending stress is same under same maximum bending. The ratio of their flexural weights is, (A) 1.118 (B) 1.338 (C) 1.228 (D) 1.108

Last Answer : (A) 1.118

The maximum load to which a fillet joint of length can be subjected to, is (A) 0.7 × S × fillet size × L (B) 2 × S × fillet size × L (C) Permissible shear stress × fillet size × L (D) (S × fillet size × L)/3

Description : The maximum load to which a fillet joint of length can be subjected to, is  (A) 0.7 × S × fillet size × L (B) 2 × S × fillet size × L (C) Permissible shear stress × fillet size × L (D) (S × fillet size × L)/3 

Last Answer : (A) 0.7 × S × fillet size × L

Area of steel required per metre width of pavement for a length of 20 m for design wheel load 6300 kg and permissible stress in steel 1400 kg/cm2 , is (A) 70 kg/sq cm (B) 80 kg/sq cm (C) 90 kg/sq cm (D) 100 kg/sq cm

Description : Area of steel required per metre width of pavement for a length of 20 m for design wheel load 6300 kg and permissible stress in steel 1400 kg/cm2 , is (A) 70 kg/sq cm (B) 80 kg/sq cm (C) 90 kg/sq cm (D) 100 kg/sq cm

Last Answer : Answer: Option C

A rod, 120cm long and of diameter 3.0 cm is subjected to an axial pull of 18 kN. The stress in N/mm2 is. a. 22.57 b. 23.47 c. 24.57 d. 25.47

Description : A rod, 120cm long and of diameter 3.0 cm is subjected to an axial pull of 18 kN. The stress in N/mm2 is. a. 22.57 b. 23.47 c. 24.57 d. 25.47

Last Answer : d. 25.47

An R.C.C. column of 30 cm diameter is reinforced with 6 bars 12 mm placed symmetrically along the circumference. If it carries a load of 40, 000 kg axially, the stress is (A) 49.9 kg/cm2 (B) 100 kg/cm2 (C) 250 kg/cm2 (D) 175 kg/cm

Description : An R.C.C. column of 30 cm diameter is reinforced with 6 bars 12 mm placed symmetrically along the circumference. If it carries a load of 40, 000 kg axially, the stress is (A) 49.9 kg/cm2 (B) 100 kg/cm2 (C) 250 kg/cm2 (D) 175 kg/cm

Last Answer : Answer: Option A

If permissible working stresses in steel and concrete are respectively 1400 kg/cm2 and 80 kg/cm2 and modular ratio is 18, in a beam reinforced in tension side and of width 30 cm and having effective depth 46 cm, the lever arms of the section, is (A) 37 cm (B) 38 cm (C) 39 cm (D) 40 cm

Description : If permissible working stresses in steel and concrete are respectively 1400 kg/cm2 and 80 kg/cm2 and modular ratio is 18, in a beam reinforced in tension side and of width 30 cm and having effective depth 46 cm, the lever arms of the section, is (A) 37 cm (B) 38 cm (C) 39 cm (D) 40 cm

Last Answer : Answer: Option D

The Minimum bar spacing should not be less than [ A ] Diameter of the largest bar [ B ] Maximum size of aggregate [ C ] Greater of diameter of the largest bar and maximum size of aggregate [ D ] Greater of diameter of the largest bar and maximum size of aggregate plus 5 mm

Description : The Minimum bar spacing should not be less than [ A ] Diameter of the largest bar [ B ] Maximum size of aggregate [ C ] Greater of diameter of the largest bar and maximum size of aggregate [ D ] Greater of diameter of the largest bar and maximum size of aggregate plus 5 mm

Last Answer : [ D ] Greater of diameter of the largest bar and maximum size of aggregate plus 5 mm

Pick up the correct statement from the following: (A) The structural member subjected to compression and whose dimensions are small as compared to its length, is called a stmt (B) The vertical compression members are generally known as columns or stanchions (C) Deflection in lateral direction of a long column, is generally known as buckling (D) All the above

Description : Pick up the correct statement from the following:  (A) The structural member subjected to compression and whose dimensions are small as  compared to its length, is called a stmt  (B) The ... in lateral direction of a long column, is generally known as buckling  (D) All the above

Last Answer : (D) All the above

A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending strain energy stored in the bar, is (A) 411 N mm (B) 511 N mm (C) 611 N mm (D) 711 N mm

Description : A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a  load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending  strain energy stored in the ... (A) 411 N mm  (B) 511 N mm  (C) 611 N mm  (D) 711 N mm 

Last Answer : (C) 611 N mm 

At the time of marriage, a man was 6 years older to his wife. 12 years after their marriage, his age is 6/5 times the age of his wife. What was wife’s age at the time of marriage? a) 18 years b) 24 years c) 30 years d) 36 years e) None of these

Description : At the time of marriage, a man was 6 years older to his wife. 12 years after their marriage, his age is 6/5 times the age of his wife. What was wife’s age at the time of marriage? a) 18 years b) 24 years c) 30 years d) 36 years e) None of these

Last Answer : ratio of their ages, 12 years hence = 6 : 5  Difference in ages = 1 ratio = 6 years wife’s age (12 years hence) = 5 ratio = 5 × 6 years = 30 years wife’s age at the time of marriage = 30 – 12 = 18 years Answer: a)

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm

Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm

Last Answer : a) 27mm

A water main 1 m in diameter contains a fluid having pressure 1 N/mm2. If the maximum permissible tensile stress in the metal is 20 N/mm2, th thickness of the metal required would be a) 2 cm b) 2.5cm c) 1 cm d) 0.5 cm

Description : A water main 1 m in diameter contains a fluid having pressure 1 N/mm2. If the maximum permissible tensile stress in the metal is 20 N/mm2, th thickness of the metal required would be a) 2 cm b) 2.5cm c) 1 cm d) 0.5 cm

Last Answer : b) 2.5cm