Which is the correct relationship for a centrifugal pump? (Where, D = Impeller diameter, inches H = Head developed, ft of liquid pumped N = Speed of pump, rpm) (A) D = 1840 H0.5 /N (B) D = 1840 N/H0.5 (C) H = 1840 D0.5 /N (D) D = 1840 H/N

Which is the correct relationship for a centrifugal pump? (Where, D =
Impeller diameter, inches H = Head developed, ft of liquid pumped N =
Speed of pump, rpm)
(A) D = 1840 H0.5
/N
(B) D = 1840 N/H0.5
(C) H = 1840 D0.5
/N
(D) D = 1840 H/N
by

1 Answer

Answer :

(A) D = 1840 H0.5
/N
by

Related questions

The head developed by a centrifugal pump is largely determined by the (A) Power of the pump(B) Nature of the liquid being pumped(C) Angle of the vanes and the speed of the tip of the impeller(D) Vapour pressure of the liquid

Description : The head developed by a centrifugal pump is largely determined by the (A) Power of the pump (B) Nature of the liquid being pumped (C) Angle of the vanes and the speed of the tip of the impeller (D) Vapour pressure of the liquid

Last Answer : (C) Angle of the vanes and the speed of the tip of the impeller

Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) NPSH required (B) BHP required by the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Description : Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) ... the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Head developed by a centrifugal pump depends on its (A) Speed (B) Impeller diameter (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Head developed by a centrifugal pump depends on its (A) Speed (B) Impeller diameter (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : C) Both (A) and (B)

In case of a centrifugal pump, the theoretical head developed is dependent on the __________ the impeller. (A) Speed of (B) Diameter of (C) Fluid velocity leaving (D) All (A), (B) and (C)

Description : In case of a centrifugal pump, the theoretical head developed is dependent on the __________ the impeller. (A) Speed of (B) Diameter of (C) Fluid velocity leaving (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Theoretical head developed by a centrifugal pump does not depend upon the __________ the impeller. (A) Radius of (B) Speed of (C) Fluid velocity leaving (D) None of these

Description : Theoretical head developed by a centrifugal pump does not depend upon the __________ the impeller. (A) Radius of (B) Speed of (C) Fluid velocity leaving (D) None of these

Last Answer : (D) None of these

With a constant diameter impeller of a centrifugal pump (A) Its capacity varies directly as the square of speed (B) Head varies as the square of speed (C) Horsepower input varies as the square of speed (D) Head varies as the speed

Description : With a constant diameter impeller of a centrifugal pump (A) Its capacity varies directly as the square of speed (B) Head varies as the square of speed (C) Horsepower input varies as the square of speed (D) Head varies as the speed

Last Answer : (B) Head varies as the square of speed

At a constant speed of the centrifugal pump, it’s __________ the impeller diameter. (A) Capacity varies directly with (B) Head varies as the square of (C) Horsepower varies as the cube of (D) All (A), (B) and (C)

Description : At a constant speed of the centrifugal pump, it’s __________ the impeller diameter. (A) Capacity varies directly with (B) Head varies as the square of (C) Horsepower varies as the cube of (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the power consumed now will be __________ hp. (A) 0.5 (B) 2 (C) 4 (D) 1

Description : A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the power consumed now will be __________ hp. (A) 0.5 (B) 2 (C) 4 (D) 1

Last Answer : (A) 0.5

A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, then the new head will be __________ metres. (A) 2 (B) 4 (C) 8 (D) 5.5

Description : A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, then the new head will be __________ metres. (A) 2 (B) 4 (C) 8 (D) 5.5

Last Answer : (A) 2

A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the new discharge will be __________ litres/minute. (A) 500 (B) 200 (C) 1000 (D) 750

Description : A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the new discharge will be __________ litres/minute. (A) 500 (B) 200 (C) 1000 (D) 750

Last Answer : (A) 500

Centrifugal pump is normally classified on the basis of the (A) rpm (B) Type of casing (C) Impeller blade angle (D) Number of blades in impeller

Description : Centrifugal pump is normally classified on the basis of the (A) rpm (B) Type of casing (C) Impeller blade angle (D) Number of blades in impeller

Last Answer : (B) Type of casing

The capacity of a centrifugal pump Can be increased by increasing the (A) Impeller diameter or speed (B) Number of pumps and joining them in series (C) Number of pumps and joining them in parallel (D) All (A), (B) and (C)

Description : The capacity of a centrifugal pump Can be increased by increasing the (A) Impeller diameter or speed (B) Number of pumps and joining them in series (C) Number of pumps and joining them in parallel (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Which of the following is not the function of a volute casing provided in a centrifugal pump? (A) To reduce the head loss in discharge (B) To increase the pump efficiency (C) To collect liquid from the periphery of the impeller and to transmit it to the delivery pipe at constant velocity (D) To increase the pump discharge rate

Description : Which of the following is not the function of a volute casing provided in a centrifugal pump? (A) To reduce the head loss in discharge (B) To increase the pump efficiency (C) To collect liquid ... and to transmit it to the delivery pipe at constant velocity (D) To increase the pump discharge rate

Last Answer : Option D

Which of the following options will facilitate the achievement of a very high head (say 30 metres) in case of a centrifugal pump? (A) Increasing the impeller speed and the volute area (B) Increasing the number of vanes in the impeller (C) Mounting of two or more impellers in series on a single shaft (D) Either of (A), (B) or (C)

Description : Which of the following options will facilitate the achievement of a very high head (say 30 metres) in case of a centrifugal pump? (A) Increasing the impeller speed and the volute area (B) Increasing the number of vanes ... or more impellers in series on a single shaft (D) Either of (A), (B) or (C)

Last Answer : (C) Mounting of two or more impellers in series on a single shaft

In case of a centrifugal pump, the ratio of total delivered pressure to pressure developed with the impeller is called the __________ efficiency. (A) Manometric (B) Mechanical (C) Volumetric (D) Overall

Description : In case of a centrifugal pump, the ratio of total delivered pressure to pressure developed with the impeller is called the __________ efficiency. (A) Manometric (B) Mechanical (C) Volumetric (D) Overall

Last Answer : (A) Manometric

Design of the casing of centrifugal pump should be such as to minimise the (A) Back flow through impeller (B) Loss of kinetic head (C) Loss of static head (D) None of these

Description : Design of the casing of centrifugal pump should be such as to minimise the (A) Back flow through impeller (B) Loss of kinetic head (C) Loss of static head (D) None of these

Last Answer : (B) Loss of kinetic head

In case of a, centrifugal pump, the ratio h1/h2is termed as the __________ efficiency (where, h1 = actual measured head & h2 = head imparted to the fluid by impeller). (A) Mechanical (B) Overall (C) Volumetric (D) Impeller

Description : In case of a, centrifugal pump, the ratio h1/h2is termed as the __________ efficiency (where, h1 = actual measured head & h2 = head imparted to the fluid by impeller). (A) Mechanical (B) Overall (C) Volumetric (D) Impeller

Last Answer : A) Mechanical

Erosion and pits formation on the impeller of a centrifugal pump may be due to (A) Cavitation (B) Low speed of impeller (C) Its operation with delivery valve closed for considerable time after starting the pump (D) Off centering of pump with motor

Description : Erosion and pits formation on the impeller of a centrifugal pump may be due to (A) Cavitation (B) Low speed of impeller (C) Its operation with delivery valve closed for considerable time after starting the pump (D) Off centering of pump with motor

Last Answer : (A) Cavitation

The maximum head that can be developed by a single impeller is __________ ft(A) 25(B) 100(C) 250-300(D) 1000.

Description : The maximum head that can be developed by a single impeller is __________ ft. (A) 25 (B) 100 (C) 250-300 (D) 1000

Last Answer : (C) 250-300

The peripheral velocity at inlet of a centrifugal pump having inlet diameter of 25 cms and rotating at 950 rpm is __________ m/sec. (A) 1.8 (B) 12.4 (C) 186.2 (D) 736.4

Description : The peripheral velocity at inlet of a centrifugal pump having inlet diameter of 25 cms and rotating at 950 rpm is __________ m/sec. (A) 1.8 (B) 12.4 (C) 186.2 (D) 736.4

Last Answer : (B) 12.4

In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) Discharge of water by a centrifugal pump being run at a constant rpm (B) Water flow in the suction and discharge pipe of a reciprocating pump (C) Water discharge from a vertical vessel in which constant level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe

Description : In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) ... level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe

Last Answer : (B) Water flow in the suction and discharge pipe of a reciprocating pump

Liquid delivery by centrifugal pump starts, only when the head developed by it is equal to the __________ head. (A) Manometric (B) Total (C) Static (D) Friction

Description : Liquid delivery by centrifugal pump starts, only when the head developed by it is equal to the __________ head. (A) Manometric (B) Total (C) Static (D) Friction

Last Answer : (A) Manometric

Cavitation occurs in a centrifugal pump when the suction pressure is (A) Less than the vapour pressure of the liquid at that temperature (B) Greater than the vapour pressure of the liquid at that temperature (C) Equal to the vapour pressure (D) Equal to the developed head

Description : Cavitation occurs in a centrifugal pump when the suction pressure is (A) Less than the vapour pressure of the liquid at that temperature (B) Greater than the vapour pressure of the liquid at that temperature (C) Equal to the vapour pressure (D) Equal to the developed head

Last Answer : (A) Less than the vapour pressure of the liquid at that temperature

Pick up the correct statement from the following regarding radial flow centrifugal pumps: (A) These are provided with volute type or turbine type casings (B) In involute type of radial flow centrifugal pump, the impeller discharges into a gradually expanding spiral casing (C) The efficiency of turbine type of radial flow centrifugal pump, is always higher than that of volute type (D) All the above

Description : Pick up the correct statement from the following regarding radial flow centrifugal pumps:  (A) These are provided with volute type or turbine type casings  (B) In involute type of radial flow ... centrifugal pump, is always higher than that of  volute type  (D) All the above 

Last Answer : (D) All the above 

The most important factor, which determines the maximum height to which water can be lifted by a pump at standard temperature is the (A) Barometric pressure (B) Speed of the impeller (C) Diameter of the impeller (D) Both (B) and (C)

Description : The most important factor, which determines the maximum height to which water can be lifted by a pump at standard temperature is the (A) Barometric pressure (B) Speed of the impeller (C) Diameter of the impeller (D) Both (B) and (C)

Last Answer : (A) Barometric pressure

Priming of a centrifugal pump is done to (A) Increase the mass flow rate of fluid (B) Develop effective pressure rise by the pump (C) Avoid chances of separation inside the impeller (D) None of these

Description : Priming of a centrifugal pump is done to (A) Increase the mass flow rate of fluid (B) Develop effective pressure rise by the pump (C) Avoid chances of separation inside the impeller (D) None of these

Last Answer : (C) Avoid chances of separation inside the impeller

A centrifugal pump is called a turbine pump, if it is having a (A) Turbine type impeller (B) Vaned diffusion casing (C) Rotating vaned volute (D) None of these

Description : A centrifugal pump is called a turbine pump, if it is having a (A) Turbine type impeller (B) Vaned diffusion casing (C) Rotating vaned volute (D) None of these

Last Answer : (B) Vaned diffusion casing

A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Description : A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Last Answer : (A) Employs such an impeller, through which the flow is a combination of radial & axial flow

Crude oil is pumped by a __________ pump. (A) Gear (B) Centrifugal

Description : Crude oil is pumped by a __________ pump. (A) Gear (B) Centrifugal

Last Answer : (B) Centrifugal

Medium viscosity lubricating oil can be most ideally pumped by a __________ pump. (A) Vane (B) Piston (C) Centrifugal (D) Plunger

Description : Medium viscosity lubricating oil can be most ideally pumped by a __________ pump. (A) Vane (B) Piston (C) Centrifugal (D) Plunger

Last Answer : (A) Vane

rpm of a trommel at critical speed is given by (where, D = Diameter of trommel in ft) (A) 76.65/D (B) 76.65/√D (C) 76.65/D2 (D) 76.75 √D

Description : rpm of a trommel at critical speed is given by (where, D = Diameter of trommel in ft) (A) 76.65/D (B) 76.65/√D (C) 76.65/D2 (D) 76.75 √D

Last Answer : (B) 76.65/√D

A liquid is pumped at the rate of 600 litres using 1000 rpm. If the rpm is changed to 1100, the liquid pumped is __________ litres. (A) 600(B) 660 (C) 1.1 (D) 60

Description : A liquid is pumped at the rate of 600 litres using 1000 rpm. If the rpm is changed to 1100, the liquid pumped is __________ litres. (A) 600 (B) 660 (C) 1.1 (D) 60

Last Answer : (B) 660

At low Reynold's number, the power (P) required for agitating a fluid in a stirred tank becomes independent of inertial forces. In this limit, indicate which of the following relations is satisfied: Po = ρ/ρN3 D5 : Power number Re = ρ N D2 /μ: Reynold's number N is the impeller rotational speed, and D is the impeller diameter. (A) Po ∝ Re -1.0 (B) Po ∝ Re 0.0 (C) Po ∝ Re 0.5 (D) Po ∝ Re 1.0

Description : At low Reynold's number, the power (P) required for agitating a fluid in a stirred tank becomes independent of inertial forces. In this limit, indicate which of the following relations is satisfied: Po = ρ/ρN3 D5 : Power number Re = ρ N D2 ... Re -1.0 (B) Po ∝ Re 0.0 (C) Po ∝ Re 0.5 (D) Po ∝ Re 1.0

Last Answer : (B) Po ∝ Re 0.0 (C) Po ∝ Re 0.5

In centrifugal pumps, cavitation occurs, when pressure of the impeller eye or vane becomes (A) Less than atmospheric pressure (B) More than liquid vapor pressure (C) Less than liquid vapor pressure (D) More than atmospheric pressure

Description : In centrifugal pumps, cavitation occurs, when pressure of the impeller eye or vane becomes (A) Less than atmospheric pressure (B) More than liquid vapor pressure (C) Less than liquid vapor pressure (D) More than atmospheric pressure

Last Answer : (C) Less than liquid vapor pressure

Which one of the following statements is correct? A. Reciprocating compressors are used to supply large quantities of air at a lower pressure ratio B. Centrifugal compressors are used to supply large quantities of air at a lower pressure ratio C. Centrifugal compressors are used to supply small quantities of air at a lower pressure ratio D. Centrifugal compressors cannot be run at high speed because of impeller, diffuser and casing.

Description : Which one of the following statements is correct? A. Reciprocating compressors are used to supply large quantities of air at a lower pressure ratio B. Centrifugal compressors are used to supply ... . Centrifugal compressors cannot be run at high speed because of impeller, diffuser and casing.

Last Answer : ANSWER : B

The pump impeller and the turbine runner in a hydraulic torque converter (A) Have the same diameter (B) Have different diameters (C) Are directly coupled (D) None of these

Description : The pump impeller and the turbine runner in a hydraulic torque converter (A) Have the same diameter (B) Have different diameters (C) Are directly coupled (D) None of these

Last Answer : (B) Have different diameters

Power required by a centrifugal pump is proportional to (where, D = diameter, N = r.p.m) (A) N2D3 (B) ND2 (C) N2D (D) N3D5

Description : Power required by a centrifugal pump is proportional to (where, D = diameter, N = r.p.m) (A) N2D3 (B) ND2 (C) N2D (D) N3D5

Last Answer : (D) N3D5

Maximum theoretical suction lift for water at 15°C by a centrifugal pump is 34 ft. The same for water at 90°C will be __________ ft. (A) 40 (B) 34 (C) 8 (D) 37

Description : Maximum theoretical suction lift for water at 15°C by a centrifugal pump is 34 ft. The same for water at 90°C will be __________ ft. (A) 40 (B) 34 (C) 8 (D) 37

Last Answer : (C) 8

Net positive suction head (NPSH) of a centrifugal pump must be (A) Greater than the vapour pressure of the liquid (B) Less than the vapour pressure of the liquid(C) Equal to the vapour pressure of the liquid(D) Less than barometric pressure

Description : Net positive suction head (NPSH) of a centrifugal pump must be (A) Greater than the vapour pressure of the liquid (B) Less than the vapour pressure of the liquid (C) Equal to the vapour pressure of the liquid (D) Less than barometric pressure

Last Answer : (A) Greater than the vapour pressure of the liquid

The net positive suction head (NPSH) of a centrifugal pump is defined as the sum of the velocity head and the pressure head at the (A) Discharge (B) Suction (C) Suction minus vapor pressure of the liquid at suction temperature (D) Discharge minus vapor pressure of the liquid at the discharge temperature

Description : The net positive suction head (NPSH) of a centrifugal pump is defined as the sum of the velocity head and the pressure head at the (A) Discharge (B) Suction (C) Suction minus vapor ... of the liquid at suction temperature (D) Discharge minus vapor pressure of the liquid at the discharge temperature

Last Answer : (C) Suction minus vapor pressure of the liquid at suction temperature

The net positive suction head (NPSH) of a centrifugal pump is defined as the sum of the velocity head and the pressure head at the (A) Discharge (B) Suction (C) Suction minus vapor pressure of the liquid at suction temperature (D) Discharge minus vapor pressure of the liquid at the discharge temperature

Description : The net positive suction head (NPSH) of a centrifugal pump is defined as the sum of the velocity head and the pressure head at the (A) Discharge (B) Suction (C) Suction minus vapor ... of the liquid at suction temperature (D) Discharge minus vapor pressure of the liquid at the discharge temperature

Last Answer : (C) Suction minus vapor pressure of the liquid at suction temperature

Specific speed of a centrifugal pump depends upon the __________ head. (A) Suction (B) Delivery (C) Manometric (D) None of these

Description : Specific speed of a centrifugal pump depends upon the __________ head. (A) Suction (B) Delivery (C) Manometric (D) None of these

Last Answer : (D) None of these

Height of liquid in agitation tank is normally maintained equal to the tank diameter. However, if the tank is too tall and a large liquid hold up is desired, then two or more impellers mounted on the same shaft may be used. The clearance between the tank bottom and the bottom most impeller should be about (where, D = impeller diameter) (A) 0.5 D (B) D (C) 1.5 D (D) 2 D

Description : Height of liquid in agitation tank is normally maintained equal to the tank diameter. However, if the tank is too tall and a large liquid hold up is desired, then two or more impellers mounted on the same shaft may be used. The ... where, D = impeller diameter) (A) 0.5 D (B) D (C) 1.5 D (D) 2 D

Last Answer : (B) D

The Sieder-Tate correlation for heat transfer in turbulent flow in pipe gives Nu α Re 0.8 , where, Nu is the Nusselt number and Re is the Reynolds number for the flow. Assuming that this relation is valid, the heat transfer co-efficient varies with the pipe diameter (D) as (A) D-1.8 (B) D-0.2 (C) D0.2 (D) D1.8

Description : The Sieder-Tate correlation for heat transfer in turbulent flow in pipe gives Nu α Re 0.8 , where, Nu is the Nusselt number and Re is the Reynolds number for the flow. Assuming that this relation is valid, the heat transfer co-efficient ... pipe diameter (D) as (A) D-1.8 (B) D-0.2 (C) D0.2 (D) D1.8

Last Answer : (B) D-0.2

Power required for mixing Newtonian fluids is a function of the (A) Speed of impeller, diameter of impeller & viscosity (B) Density & viscosity of fluid only (C) Density of fluid, viscosity of fluid & impeller dia only (D) None of these

Description : Power required for mixing Newtonian fluids is a function of the (A) Speed of impeller, diameter of impeller & viscosity (B) Density & viscosity of fluid only (C) Density of fluid, viscosity of fluid & impeller dia only (D) None of these

Last Answer : (D) None of these

A fluid is pumped at the rate of 10 lb/sec to a height of 55 ft. The horse power required is __________ hp. (A) 1 (B) 10/55 (C) 5.5 (D) 1/55

Description : A fluid is pumped at the rate of 10 lb/sec to a height of 55 ft. The horse power required is __________ hp. (A) 1 (B) 10/55 (C) 5.5 (D) 1/55

Last Answer : (A) 1

The blades of a centrifugal impeller are said to be curved forward, if the __________ of the motion of impeller blades. (A) Inlet tip of a blade curves in a direction opposite to that (B) Outlet tip of a blade curves in a direction opposite to that (C) Inlet tip of a blade is towards the direction (D) Outlet tip of a blade is towards the direction

Description : The blades of a centrifugal impeller are said to be curved forward, if the __________ of the motion of impeller blades. (A) Inlet tip of a blade curves in a direction opposite to that (B) Outlet tip ... Inlet tip of a blade is towards the direction (D) Outlet tip of a blade is towards the direction

Last Answer : (D) Outlet tip of a blade is towards the direction

Delivery of insufficient quantity of liquid by a pump may be caused by (A) Air leak in the inlet (B) Low rpm (C) Too high a lift (D) All (A), (B) and (C)

Description : Delivery of insufficient quantity of liquid by a pump may be caused by (A) Air leak in the inlet (B) Low rpm (C) Too high a lift (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Pick up the correct statement from the following: (A) At a particular speed of operation, the head produced decreases with the increase of discharge (B) At zero discharge, discharge valve remaining closed, the head developed is maximum which is known as shut-off head (C) At a particular speed the discharge at which efficiency of a pump is maximum, is known as normal discharge (D) All the above

Description : Pick up the correct statement from the following: (A) At a particular speed of operation, the head produced decreases with the increase of discharge (B) At zero discharge, discharge valve remaining closed ... which efficiency of a pump is maximum, is known as normal discharge (D) All the above

Last Answer : (D) All the above