Which of the following statements are true about eccentrically loaded circular base? a) All bolts are symmetrically spaced with equal angle on either side of vertical b) Bolts are not preloaded c) Bearing is rigid d) Dowel pins are used to relieve stresses

Which of the following statements are true about eccentrically loaded circular base?

a) All bolts are symmetrically spaced with equal angle on either side of vertical

b) Bolts are not preloaded

c) Bearing is rigid

d) Dowel pins are used to relieve stresses
by

1 Answer

Answer :

a) All bolts are symmetrically spaced with equal angle on either side of vertical
by

Related questions

If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5

Description : If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5

Last Answer : c) 4

If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5

Description : If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5

Last Answer : c) 4

Which of the following is not a function of washer? a) Distributes load over a large area of clamped parts b) Provides bearing surface over large clearance bolts c) Prevents marring of the bolt head and nut surface d) Helps in locking of the fastener

Description : Which of the following is not a function of washer? a) Distributes load over a large area of clamped parts b) Provides bearing surface over large clearance bolts c) Prevents marring of the bolt head and nut surface d) Helps in locking of the fastener

Last Answer : d) Helps in locking of the fastener

The function of an expansion joint in rigid pavements is to (A) Relieve warping stresses (B) Relieve shrinkage stresses (C) Resist stresses due to expansion (D) Allow free expansion

Description : The function of an expansion joint in rigid pavements is to (A) Relieve warping stresses (B) Relieve shrinkage stresses (C) Resist stresses due to expansion (D) Allow free expansion

Last Answer : Answer: Option D

Select the incorrect statement from the following In eccentrically loaded columns, [ A ] The tensile strength of concrete is ignored [ B ] Design stress – strain curve for steel in compression is the same as in tension [ C ] The strain at different points in the section will be same [ D ] Plane section remain plane even after bending

Description : Select the incorrect statement from the following In eccentrically loaded columns, [ A ] The tensile strength of concrete is ignored [ B ] Design stress - strain curve for steel in compression is the ... different points in the section will be same [ D ] Plane section remain plane even after bending

Last Answer : [ C ] The strain at different points in the section will be same

The following bracket is welded to the vertical column. The joint undergoes torsional stresses. a) True b) False

Description : The following bracket is welded to the vertical column. The joint undergoes torsional stresses. a) True b) False

Last Answer : b) False

In symmetrically reinforced sections, shrinkage stresses in concrete and steel are respectively (A) Compressive and tensile (B) Tensile and compressive (C) Both compressive (D) Both tensile

Description : In symmetrically reinforced sections, shrinkage stresses in concrete and steel are respectively (A) Compressive and tensile (B) Tensile and compressive (C) Both compressive (D) Both tensile

Last Answer : Answer: Option D

Angle of obliquity is defined as a. Angle between the plane on which stresses are evaluated and one of the given planes b. Angle between resultant stress and the plane of given normal stress c. Angle between resultant stress and shear stress d. Angle between resultant stress and normal stress

Description : Angle of obliquity is defined as a. Angle between the plane on which stresses are evaluated and one of the given planes b. Angle between resultant stress and the plane of given normal stress c. Angle between resultant stress and shear stress d. Angle between resultant stress and normal stress

Last Answer : d. Angle between resultant stress and normal stress

All the maximum shear stresses are at an angle of (a)45 0 (b) 90 0 (c) 135 0 (d) None

Description : All the maximum shear stresses are at an angle of (a)45 0 (b) 90 0 (c) 135 0 (d) None

Last Answer : (b) 90 0

All the principal stresses are at an angle of (a)90 0 (b) 45 0 (c) 135 0 (d) None

Description : All the principal stresses are at an angle of (a)90 0 (b) 45 0 (c) 135 0 (d) None

Last Answer : (a)90 0

All the principal stresses are at an angle of (a) 45 0 (b) 60 0 (c) 75 0 (d) None

Description : All the principal stresses are at an angle of (a) 45 0 (b) 60 0 (c) 75 0 (d) None

Last Answer : (d) None

Clamp coupling employ bolts. a) True b) False

Description : Clamp coupling employ bolts. a) True b) False

Last Answer : a) True

Clamp coupling employ bolts. a) True b) False

Description : Clamp coupling employ bolts. a) True b) False

Last Answer : a) True

In hydrodynamic bearing, (A) The axis of journal is eccentric with respect to axis of bearing (B) The axis of journal is concentric with respect to axis of bearing (C) The axis can be either eccentric or concentric depending upon speed (D) None of the above

Description : In hydrodynamic bearing, (A) The axis of journal is eccentric with respect to axis of bearing (B) The axis of journal is concentric with respect to axis of bearing (C) The axis can be either eccentric or concentric depending upon speed (D) None of the above

Last Answer : (A) The axis of journal is eccentric with respect to axis of bearing

In hydrostatic bearing, (A) The axis of journal is eccentric with respect to axis of bearing (B) The axis of journal is concentric with respect to axis of bearing (C) The axis can be either eccentric or concentric depending upon speed (D) None of the above

Description : In hydrostatic bearing, (A) The axis of journal is eccentric with respect to axis of bearing (B) The axis of journal is concentric with respect to axis of bearing (C) The axis can be either eccentric or concentric depending upon speed (D) None of the above

Last Answer : (B) The axis of journal is concentric with respect to axis of bearing

When comes down to stress reduction, which one is preferred? a) Solid flywheel b) Split flywheel c) Both have equal stresses d) Cannot be determined

Description : When comes down to stress reduction, which one is preferred? a) Solid flywheel b) Split flywheel c) Both have equal stresses d) Cannot be determined

Last Answer : b) Split flywheel

Power is transmitted by only in rigid flange coupling. a) True b) False

Description : Power is transmitted by only in rigid flange coupling. a) True b) False

Last Answer : b) False

Flange coupling is rigid types coupling. A. True B. False

Description : Flange coupling is rigid types coupling. A. True B. False

Last Answer : A. True

Universal coupling is rigid types coupling. A. True B. False

Description : Universal coupling is rigid types coupling. A. True B. False

Last Answer : B. False

Flange coupling is rigid types coupling. A. True B. False

Description : Flange coupling is rigid types coupling. A. True B. False

Last Answer : A. True

Universal coupling is rigid types coupling. A. True B. False

Description : Universal coupling is rigid types coupling. A. True B. False

Last Answer : B. False

Power is transmitted by only in rigid flange coupling. a) True b) False

Description : Power is transmitted by only in rigid flange coupling. a) True b) False

Last Answer : b) False

A clearance bearing is design accurately to keep the radius of journal and bearing equal. a) Journal radius is kept larger b) Journal radius is kept smaller c) True d) Can’t be determined

Description : A clearance bearing is design accurately to keep the radius of journal and bearing equal. a) Journal radius is kept larger b) Journal radius is kept smaller c) True d) Can’t be determined

Last Answer : b) Journal radius is kept smaller

Which of the following help in accomplishing the locking? a) Creating supplementary friction b) Using special locking devices like split pins c) By plastic deformation d) All of the listed

Description : Which of the following help in accomplishing the locking? a) Creating supplementary friction b) Using special locking devices like split pins c) By plastic deformation d) All of the listed

Last Answer : d) All of the listed

Calculate the force acting on the each pin in flexible coupling if torque transmitted is 397N-m and PCD=120mm with number of pins 6. a) 1400.3N b) 1102.8N c) 1320.3N d) None of the listed

Description : Calculate the force acting on the each pin in flexible coupling if torque transmitted is 397N-m and PCD=120mm with number of pins 6. a) 1400.3N b) 1102.8N c) 1320.3N d) None of the listed

Last Answer : b) 1102.8N

If shaft diameter is 30mm and number of pins emplaced are 6, then the diameter of the pin will be? a) 6.4mm b) 5.6mm c) 6.1mm d) 5.9mm

Description : If shaft diameter is 30mm and number of pins emplaced are 6, then the diameter of the pin will be? a) 6.4mm b) 5.6mm c) 6.1mm d) 5.9mm

Last Answer : c) 6.1mm

In case of partial bearing, the angle of contact of the bushing with the journal is (A) 270° (B) More than 180° (C) Less than 180° (D) 360°

Description : In case of partial bearing, the angle of contact of the bushing with the journal is (A) 270° (B) More than 180° (C) Less than 180° (D) 360°

Last Answer : (C) Less than 180°

In case of full journal bearing, the angle of contact of the bushing with the journal is (A) 60° (B) 90° (C) 180° (D) 360°

Description : In case of full journal bearing, the angle of contact of the bushing with the journal is (A) 60° (B) 90° (C) 180° (D) 360°

Last Answer : (D) 360°

In case of partial bearing, the angle of contact of the bushing with the journal is usually (A) 120° (B) 180° (C) 45° (D) 360°

Description : In case of partial bearing, the angle of contact of the bushing with the journal is usually (A) 120° (B) 180° (C) 45° (D) 360°

Last Answer : (A) 120°

The shear plane in case of bolts should (a) be across threaded portion of shank (b) be parallel to axis of bolt (c) be normal to threaded portion of shank (d) never be across the threaded portion (e) none of the above.

Description : The shear plane in case of bolts should (a) be across threaded portion of shank (b) be parallel to axis of bolt (c) be normal to threaded portion of shank (d) never be across the threaded portion (e) none of the above.

Last Answer : (d) never be across the threaded portion

The shock absorbing capacity of bolts can be increased by a) Increasing the shank diameter b) Decreasing the length of shank portion of bolt c) Increase the shank diameter and decreasing the length of shank d) None of the listed

Description : The shock absorbing capacity of bolts can be increased by a) Increasing the shank diameter b) Decreasing the length of shank portion of bolt c) Increase the shank diameter and decreasing the length of shank d) None of the listed

Last Answer : d) None of the listed

Which of the following are good for parts that are seldom dismantled. a) Through Bolts b) Tap Bolts c) Studs d) Cannot be stated

Description : Which of the following are good for parts that are seldom dismantled. a) Through Bolts b) Tap Bolts c) Studs d) Cannot be stated

Last Answer : b) Tap Bolts

If there is no place to accommodate the nut, then one would choose the a) Through Bolts b) Tap Bolts c) Studs d) None of the mentioned

Description : If there is no place to accommodate the nut, then one would choose the a) Through Bolts b) Tap Bolts c) Studs d) None of the mentioned

Last Answer : b) Tap Bolts

The connecting rod bolts are tightened up so that the initial tightening stress (A) Approaches yield point (B) Approaches endurance limit (C) Approaches (yield point stress/factor of safety) (D) Approaches (endurance limit stress/factor of safety)

Description : The connecting rod bolts are tightened up so that the initial tightening stress (A) Approaches yield point (B) Approaches endurance limit (C) Approaches (yield point stress/factor of safety) (D) Approaches (endurance limit stress/factor of safety)

Last Answer : (A) Approaches yield point

The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by external cyclic load (C) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three

Description : The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by ... ) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three

Last Answer : (D) All the three

Setscrews are (A) Similar to tap bolts except that a greater variety of shapes of heads are available (B) Slotted for screw driver and generally used with a nut (C) Used to prevent relative motion between parts (D) Similar to studs

Description : Setscrews are (A) Similar to tap bolts except that a greater variety of shapes of heads are available (B) Slotted for screw driver and generally used with a nut (C) Used to prevent relative motion between parts (D) Similar to studs

Last Answer : (C) Used to prevent relative motion between parts

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm

Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm

Last Answer : a) 27mm

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Last Answer : c) 41666.7N

While designing a flange coupling, care is taken so that (A) Shaft is the weakest component (B) Bolts are the weakest component (C) Key is the weakest component (D) The flange is the weakest component

Description : While designing a flange coupling, care is taken so that (A) Shaft is the weakest component (B) Bolts are the weakest component (C) Key is the weakest component (D) The flange is the weakest component

Last Answer : (C) Key is the weakest component

In designing a flange coupling, the pitch circle diameter of bolts is taken as (where d = Diameter of the shaft) (A) 2 d (B) 3 d (C) 4 d (D) 5 d

Description : In designing a flange coupling, the pitch circle diameter of bolts is taken as (where d = Diameter of the shaft) (A) 2 d (B) 3 d (C) 4 d (D) 5 d

Last Answer : (B) 3 d

The helical spring ad wire of helical torsion spring, both are subjected to torsional shear stresses. a) True b) False

Description : The helical spring ad wire of helical torsion spring, both are subjected to torsional shear stresses. a) True b) False

Last Answer : b) False

Stress concentration is defined as the localization of high stresses due to irregularities present in the component and no changes of the cross section. a) True b) False

Description : Stress concentration is defined as the localization of high stresses due to irregularities present in the component and no changes of the cross section. a) True b) False

Last Answer : b) False

In hydrodynamic bearing, when the shaft begins to rotate in clockwise direction, (A) The journal climbs to the right side of the bearing without metal to metal contact (B) The journal climbs to the left side of the bearing without metal to metal contact (C) The journal sinks down to the bottom of the bearing (D) The journal is at the center of the bearing

Description : In hydrodynamic bearing, when the shaft begins to rotate in clockwise direction, (A) The journal climbs to the right side of the bearing without metal to metal contact (B) The journal climbs to the left ... sinks down to the bottom of the bearing (D) The journal is at the center of the bearing

Last Answer : (A) The journal climbs to the right side of the bearing without metal to metal contact

Consider the following statements: [IES 2007] For a journal rotating in a bearing under film lubrication conditions, the frictional resistance is- 1. Proportional to the area of contact 2. Proportional to the viscosity of lubricant 3. Proportional to the speed of rotation 4. Independent of the pressure Which of the statements given above are correct? (a) 1, 2, 3 and 4 (b) 1 and 4 only (c) 2, 3 and 4 only (d) 2 and 3 only

Description : Consider the following statements: [IES 2007] For a journal rotating in a bearing under film lubrication conditions, the frictional resistance is- 1. Proportional to the area of contact 2. Proportional to the viscosity of lubricant 3. ... 4 (b) 1 and 4 only (c) 2, 3 and 4 only (d) 2 and 3 only

Last Answer : (a) 1, 2, 3 and 4

Consider tile following statements: [IES-1993; 2002; 2006] Radius of friction circle for a journal bearing depends upon 1. Coefficient of friction 2. Radius of the journal 3. Angular speed of rotation of the shaft Which of the statements given above are correct? (a) 1,2 and 3 (b) Only 1 and 2 (c) Only 2 and 3 (d) Only 1 and 3

Description : Consider tile following statements: [IES-1993; 2002; 2006] Radius of friction circle for a journal bearing depends upon 1. Coefficient of friction 2. Radius of the journal 3. Angular speed of rotation of the shaft Which of the ... ) 1,2 and 3 (b) Only 1 and 2 (c) Only 2 and 3 (d) Only 1 and 3

Last Answer : (b) Only 1 and 2

Spiral spring is quite rigid. a) Yes b) No it is flexible c) It is of moderate rigidity d) Rigidity can’t be determined

Description : Spiral spring is quite rigid. a) Yes b) No it is flexible c) It is of moderate rigidity d) Rigidity can’t be determined

Last Answer : b) No it is flexible

Welded joints are a. Hinged joint b. Rigid joint c. Freely supported joint

Description : Welded joints are a. Hinged joint b. Rigid joint c. Freely supported joint

Last Answer : b. Rigid joint

Find the shear stress in a flange at the junction of hub in rigid flanged coupling if torsional moment is 2980N-m and diameter of hub being 125mm. Also the thickness of flange is 25mm. a) 6.77N/mm2 b) 10.24N/mm2 c) 4.84N/mm2 d) 4.22N/mm2

Description : Find the shear stress in a flange at the junction of hub in rigid flanged coupling if torsional moment is 2980N-m and diameter of hub being 125mm. Also the thickness of flange is 25mm. a) 6.77N/mm2 b) 10.24N/mm2 c) 4.84N/mm2 d) 4.22N/mm2

Last Answer : c) 4.84N/mm2

Flange coupling is ............ types of coupling. A. Flexible B. Rigid

Description : Flange coupling is ............ types of coupling. A. Flexible B. Rigid

Last Answer : B. Rigid