Elastomers are (A) Thermosetting material (B) Exemplified by protein derivatives (C) Having high flexural strength (D) Having very high tensile strength and heat resistance

Elastomers are
(A) Thermosetting material
(B) Exemplified by protein derivatives
(C) Having high flexural strength
(D) Having very high tensile strength and heat resistance
by

1 Answer

Answer :

(C) Having high flexural strength
by

Related questions

Which of the following types of polymers has the strongest inter particle forces? (A) Elastomers (B) Fibres (C) Thermoplastics (D) Thermosetting polymers

Description : Which of the following types of polymers has the strongest inter particle forces? (A) Elastomers (B) Fibres (C) Thermoplastics (D) Thermosetting polymers

Last Answer : (D) Thermosetting polymers

The approximate value of the ratio between direct tensile strength and flexural strength is (A) 0.33 (B) 0.5 (C) 0.75 (D) 1.0

Description : The approximate value of the ratio between direct tensile strength and flexural strength is (A) 0.33 (B) 0.5 (C) 0.75 (D) 1.0

Last Answer : Answer: Option B

Modulus of rupture of concrete is a measure of (A) Flexural tensile strength (B) Direct tensile strength (C) Compressive strength (D) Split tensile strength

Description : Modulus of rupture of concrete is a measure of (A) Flexural tensile strength (B) Direct tensile strength (C) Compressive strength (D) Split tensile strength

Last Answer : Answer: Option A

Workability of concrete mix with low water cement ratio is determined by (A) Tensile strength test (B) Slump test (C) Compaction factor test (D) Flexural strength test

Description : Workability of concrete mix with low water cement ratio is determined by (A) Tensile strength test (B) Slump test (C) Compaction factor test (D) Flexural strength test

Last Answer : Answer: Option C

Workability of concrete mix with low water cement ratio is determined by [ A ] Tensile strength test [ B ] Slump cone test [ C ] Compaction factor test [ D ] Flexural strength test

Description : Workability of concrete mix with low water cement ratio is determined by [ A ] Tensile strength test [ B ] Slump cone test [ C ] Compaction factor test [ D ] Flexural strength test

Last Answer : [ C ] Compaction factor test

Aluminium as a material of construction suffers from the disadvantage of (A) Very high cost (B) Rather low tensile strength (C) Very low strength to weight ratio (D) Scarce availability

Description : Aluminium as a material of construction suffers from the disadvantage of (A) Very high cost (B) Rather low tensile strength (C) Very low strength to weight ratio (D) Scarce availability

Last Answer : (B) Rather low tensile strength

Liquid crystal elastomers 4D printing material achieve their activation due to a. Light b. Heat c. Electrical d. All of the above

Description : Liquid crystal elastomers 4D printing material achieve their activation due to a. Light b. Heat c. Electrical d. All of the above

Last Answer : Ans:- d. All of the above

Cast iron is having very high (A) Proximity between its elastic limit and ultimate breaking strength (B) Ductility (C) Tensile strength (D) All (A), (B) and (C)

Description : Cast iron is having very high (A) Proximity between its elastic limit and ultimate breaking strength (B) Ductility (C) Tensile strength (D) All (A), (B) and (C)

Last Answer : (A) Proximity between its elastic limit and ultimate breaking strength

Failure of a material is termed as fatigue failure, if it fails below the yield point. The resistance to fatigue failure of a material is measured by the (A) Ultimate tensile strength (U.T.S.) (B) Endurance limit (C) Elastic limit (D) None of these

Description : Failure of a material is termed as fatigue failure, if it fails below the yield point. The resistance to fatigue failure of a material is measured by the (A) Ultimate tensile strength (U.T.S.) (B) Endurance limit (C) Elastic limit (D) None of these

Last Answer : (B) Endurance limit

Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Description : Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Last Answer : (C) Creep resistance

Fatigue resistance of a material is measured by the (A) Elastic limit (B) Ultimate tensile strength (C) Young's modulus (D) Endurance limit

Description : Fatigue resistance of a material is measured by the (A) Elastic limit (B) Ultimate tensile strength (C) Young's modulus (D) Endurance limit

Last Answer : (D) Endurance limit

Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Description : Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Young's modulus of a material is the measure of its (A) Stiffness (B) Malleability (C) Creep resistance (D) Tensile strength

Description : Young's modulus of a material is the measure of its (A) Stiffness (B) Malleability (C) Creep resistance (D) Tensile strength

Last Answer : Option A

Styrene butadiene rubber (SBR) as compared to natural rubber has (A) Poor tensile strength (B) Poorer resistance (C) Greater amount of heat build up heavy loading (D) All (A), (B) and (C)

Description : Styrene butadiene rubber (SBR) as compared to natural rubber has (A) Poor tensile strength (B) Poorer resistance (C) Greater amount of heat build up heavy loading (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Styrene-butadiene-rubber (SBR) as compared to natural rubber has (A) Poorer tensile strength (B) Poorer resistance to oxidation (C) Greater amount of heat build-up under heavy loading (D) All (A), (B) and (C)

Description : Styrene-butadiene-rubber (SBR) as compared to natural rubber has (A) Poorer tensile strength (B) Poorer resistance to oxidation (C) Greater amount of heat build-up under heavy loading (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Wrought iron is having very high (A) Hardness (B) Strength (C) Corrosion resistance (D) Susceptibility to changes in its properties by heat treatment

Description : Wrought iron is having very high (A) Hardness (B) Strength (C) Corrosion resistance (D) Susceptibility to changes in its properties by heat treatment

Last Answer : (C) Corrosion resistance

Polymers are classified into four categories namely thermosetting, thermoplastic, elastomer and fibre depending upon their (A) Molecular sizes (B) Magnitude of intermolecular forces (C) Resistance to heat (D) Polymerisation mechanism

Description : Polymers are classified into four categories namely thermosetting, thermoplastic, elastomer and fibre depending upon their (A) Molecular sizes (B) Magnitude of intermolecular forces (C) Resistance to heat (D) Polymerisation mechanism

Last Answer : (B) Magnitude of intermolecular forces

The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Description : The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Last Answer : (d) endurance limit

While the thermosetting polymers are amorphous in nature, the thermoplastic polymers are either amorphous or crystalline. The crystalline polymers are characterised by the (A) Low impact strength (B) High flexibility (C) Better finish and surface appearance (D) High plastic deformation

Description : While the thermosetting polymers are amorphous in nature, the thermoplastic polymers are either amorphous or crystalline. The crystalline polymers are characterised by the (A) Low impact strength (B) High flexibility (C) Better finish and surface appearance (D) High plastic deformation

Last Answer : A) Low impact strength

Shock resisting steels should possess high (A) Hardness (B) Toughness (C) Tensile strength (D) Wear resistance

Description : Shock resisting steels should possess high (A) Hardness (B) Toughness (C) Tensile strength (D) Wear resistance

Last Answer : (B) Toughness

I need ways to test/get data about homemade plastics. What can I do with Flexural Strength and Flexural Modulus...

Description : I need ways to test/get data about homemade plastics. What can I do with Flexural Strength and Flexural Modulus...

Last Answer : answer:Strength is how strong a material is – basically breaking load. Modulus is how flexible or stretchy a material is. Does not matter if the test coupon breaks or not. Think of uncooked spaghetti vs rubber band.

According to IS: 4561978, the flexural strength of concrete is (A) Directly proportional to compressive strength (B) Inversely proportional to compressive strength (C) Directly proportional to square root of compressive strength (D) Inversely proportional to square root of compressive strength

Description : According to IS: 4561978, the flexural strength of concrete is (A) Directly proportional to compressive strength (B) Inversely proportional to compressive strength (C) Directly proportional to square root of compressive strength (D) Inversely proportional to square root of compressive strength

Last Answer : Answer: Option C

For lime concrete, (A) Slump is 50 to 75 mm (B) Flexural strength at 90 days is 0.2 N/mm2 (C) Compressive strength at 90 days is 1.5 N/mm2 (D) All the above

Description : For lime concrete, (A) Slump is 50 to 75 mm (B) Flexural strength at 90 days is 0.2 N/mm2 (C) Compressive strength at 90 days is 1.5 N/mm2 (D) All the above

Last Answer : Answer: Option D

Elastomers are:** A. Hydrophilic B. Hydrophobic C. Water-loving impression material D. Potassium alginates E. None of the above

Description : Elastomers are:** A. Hydrophilic B. Hydrophobic C. Water-loving impression material D. Potassium alginates E. None of the above

Last Answer : B. Hydrophobic

Cast iron has (A) Very high tensile strength (B) High ductility (C) High malleability (D) Elastic limit close to ultimate breaking strength

Description : Cast iron has (A) Very high tensile strength (B) High ductility (C) High malleability (D) Elastic limit close to ultimate breaking strength

Last Answer : (D) Elastic limit close to ultimate breaking strength

Cast iron has (A) High ductility (B) High malleability (C) Very high tensile strength (D) Its elastic limit very close to ultimate breaking strength

Description : Cast iron has (A) High ductility (B) High malleability (C) Very high tensile strength (D) Its elastic limit very close to ultimate breaking strength

Last Answer : (D) Its elastic limit very close to ultimate breaking strength

Sacrificial anode method is used in the protection of pipelines which are buried underground. Sacrificial anode (A) Occurs higher in the electro-chemical series of metals (B) Is exemplified by magnesium plate (C) Is much cheaper than the cathodic base material to be guarded against corrosion (D) All (A), (B) & (C)

Description : Sacrificial anode method is used in the protection of pipelines which are buried underground. Sacrificial anode (A) Occurs higher in the electro-chemical series of metals (B) Is exemplified by magnesium plate (C) ... cathodic base material to be guarded against corrosion (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

High copper amalgam lasts longer than low copper amalgam because of:** A. Increased compressive strength B. Increased corrosion resistance C. High creep D. Increased tensile strength E. Decreased setting expansion

Description : High copper amalgam lasts longer than low copper amalgam because of:**  A. Increased compressive strength  B. Increased corrosion resistance  C. High creep  D. Increased tensile strength  E. Decreased setting expansion 

Last Answer : A. Increased compressive strength 

Vulcanisation of rubber (A) Decreases its tensile strength (B) Increases its ozone & oxygen reactivity (C) Increases its oil & solvent resistance (D) Converts its plasticity into elasticity

Description : Vulcanisation of rubber (A) Decreases its tensile strength (B) Increases its ozone & oxygen reactivity (C) Increases its oil & solvent resistance (D) Converts its plasticity into elasticity

Last Answer : (D) Converts its plasticity into elasticity

Addition of plasticisers to polymers results in partial neutralisation of intermolecular forces of attraction between the macro-molecules thereby increasing its (A) Tensile strength (B) Chemical resistance (C) Flexibility (D) All (A), (B) & (C)

Description : Addition of plasticisers to polymers results in partial neutralisation of intermolecular forces of attraction between the macro-molecules thereby increasing its (A) Tensile strength (B) Chemical resistance (C) Flexibility (D) All (A), (B) & (C)

Last Answer : (C) Flexibility

Vulcanisation of rubber decreases its (A) Tensile strength (B) Resistance to organic solvents (C) Tackiness (D) Working temperature range

Description : Vulcanisation of rubber decreases its (A) Tensile strength (B) Resistance to organic solvents (C) Tackiness (D) Working temperature range

Last Answer : (C) Tackiness

Plasticisers are added to polymers to improve their (A) Tensile strength (B) Softness & flexibility (C) Acid resistance (D) Alkali resistance

Description : Plasticisers are added to polymers to improve their (A) Tensile strength (B) Softness & flexibility (C) Acid resistance (D) Alkali resistance

Last Answer : (B) Softness & flexibility

Addition of lead, sulphur and phosphorus to low carbon steel helps in improving its (A) Corrosion resistance (B) Tensile strength (C) Machinability (D) Compressive strength

Description : Addition of lead, sulphur and phosphorus to low carbon steel helps in improving its (A) Corrosion resistance (B) Tensile strength (C) Machinability (D) Compressive strength

Last Answer : (C) Machinability

Presence of cobalt in steel improves its (A) Cutting ability (B) Corrosion resistance (C) Tensile strength

Description : Presence of cobalt in steel improves its (A) Cutting ability (B) Corrosion resistance (C) Tensile strength

Last Answer : (A) Cutting ability

Vulcanisation of rubber (A) Decreases its tensile strength (B) Increases its ozone & oxygen reactivity (C) Increases its oil & solvent resistance (D) Converts its plasticity into elasticity

Description : Vulcanisation of rubber (A) Decreases its tensile strength (B) Increases its ozone & oxygen reactivity (C) Increases its oil & solvent resistance (D) Converts its plasticity into elasticity

Last Answer : (D) Converts its plasticity into elasticity

__________ of rubber decreases after its vulcanisation. (A) Resistance to the action of organic solvent (B) Tackiness (C) Maximum service temperature (D) Tensile strength

Description : __________ of rubber decreases after its vulcanisation. (A) Resistance to the action of organic solvent (B) Tackiness (C) Maximum service temperature (D) Tensile strength

Last Answer : (B) Tackiness

__________ functions are exemplified by heat and work. (A) Path (B) Point (C) State (D) None of these

Description : __________ functions are exemplified by heat and work. (A) Path (B) Point (C) State (D) None of these

Last Answer : (A) Path

Metalloids (A) Are good conductor of heat & electricity (B) Act as electron donors with metals & as electron acceptor with non metals (C) Are not necessarily solids at room temperature (D) Are compounds that exhibit both metallic & non-metallic properties to some extent and are exemplified by elements like germanium, silicon & boron

Description : Metalloids (A) Are good conductor of heat & electricity (B) Act as electron donors with metals & as electron acceptor with non metals (C) Are not necessarily solids at room temperature ... & non-metallic properties to some extent and are exemplified by elements like germanium, silicon & boron

Last Answer : D) Are compounds that exhibit both metallic & non-metallic properties to some extent and are exemplified by elements like germanium, silicon & boron

Which of the following mechanical properties of a material is most structure insensitive? (A) Modulus of elasticity (young's modulus) (B) Toughness (C) Percentage reduction of area (D) Tensile strength

Description : Which of the following mechanical properties of a material is most structure insensitive? (A) Modulus of elasticity (young's modulus) (B) Toughness (C) Percentage reduction of area (D) Tensile strength

Last Answer : (A) Modulus of elasticity (young's modulus)

Work hardening of a material (A) Decreases its tensile strength (B) Decreases its ductility (C) Increases its ductility (D) Does not affect its ductility

Description : Work hardening of a material (A) Decreases its tensile strength (B) Decreases its ductility (C) Increases its ductility (D) Does not affect its ductility

Last Answer : (B) Decreases its ductility

On decreasing the grain size of a polycrystalline material, the property most likely to deteriorate is (A) Creep (B) Toughness (C) Tensile strength (D) Fatigue

Description : On decreasing the grain size of a polycrystalline material, the property most likely to deteriorate is (A) Creep (B) Toughness (C) Tensile strength (D) Fatigue

Last Answer : (B) Toughnes

Which of the following has high tensile strength? (A) Plain hot rolled wires (B) Cold drawn wires (C) Heat treated rolled wires (D) All have same tensile strength

Description : Which of the following has high tensile strength? (A) Plain hot rolled wires (B) Cold drawn wires (C) Heat treated rolled wires (D) All have same tensile strength

Last Answer : Answer: Option B

Linear polymers are normally (A) Thermosetting (B) Thermoplastic (C) Elastometric (D) Having extremely high softening poin

Description : Linear polymers are normally (A) Thermosetting (B) Thermoplastic (C) Elastometric (D) Having extremely high softening poin

Last Answer : (B) Thermoplastic

Copper has very low (A) Malleability (B) Ductility (C) Tensile strength (D) Thermal & electrical conductivity

Description : Copper has very low (A) Malleability (B) Ductility (C) Tensile strength (D) Thermal & electrical conductivity

Last Answer : (C) Tensile strength

Cast iron is (A) Used for making shock resisting parts (B) Manufactured in cupola and is brittle (C) Having compressive strength more than its tensile strength(D) All (A), (B) & (C)

Description : Cast iron is (A) Used for making shock resisting parts (B) Manufactured in cupola and is brittle (C) Having compressive strength more than its tensile strength (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Wrought iron is not (A) Ductile & resistant to corrosion/rusting (B) Weldable easily (C) Having uniform strength in all directions (D) Having maximum tensile strength along the lines of slag distribution

Description : Wrought iron is not (A) Ductile & resistant to corrosion/rusting (B) Weldable easily (C) Having uniform strength in all directions (D) Having maximum tensile strength along the lines of slag distribution

Last Answer : Option C

A chain growth polymerisation reaction consists of three different types of reaction namely initiation reaction, propagation reaction & termination reaction. Chain growth polymerisation reaction is not involved in the manufacture of (A) Siloxane elastomers (B) Polyamides (C) Vinyl polymers (D) Urea-formaldehyde resins

Description : A chain growth polymerisation reaction consists of three different types of reaction namely initiation reaction, propagation reaction & termination reaction. Chain growth polymerisation reaction is not involved ... Siloxane elastomers (B) Polyamides (C) Vinyl polymers (D) Urea-formaldehyde resins

Last Answer : (D) Urea-formaldehyde resins

Out of all the elastomers, natural rubber has the longest elongation range & flexibility of the order of __________ percent. (A) 1-1000 (B) 1000-1500 (C) 1500-2000 (D) 2000-2500

Description : Out of all the elastomers, natural rubber has the longest elongation range & flexibility of the order of __________ percent. (A) 1-1000 (B) 1000-1500 (C) 1500-2000 (D) 2000-2500

Last Answer : (A) 1-1000

Interchain forces are the weakest in case of (A) Plastics (B) Fibres (C) Elastomers (D) Both rubber & elastomers

Description : Interchain forces are the weakest in case of (A) Plastics (B) Fibres (C) Elastomers (D) Both rubber & elastomers

Last Answer : (D) Both rubber & elastomers

The maximum deflection due to a load W at the free end of a cantilever of length L and having flexural rigidity EI, is (A) WL²/2EI (B) WL²/3EI (C) WL3 /2EI (D) WL3 /3EI

Description : The maximum deflection due to a load W at the free end of a cantilever of length L and having  flexural rigidity EI, is  (A) WL²/2EI (B) WL²/3EI (C) WL3 /2EI (D) WL3 /3EI

Last Answer : (D) WL3 /3EI