Description : If the total source voltage of the three-wire distribution system shown in the illustration is 240 volts, what is the voltage across load L5? [ NOTE: Kirchhoff's voltage and current laws apply ] EL-0075 A. 110.4 volts B. 112.2 volts C. 113.0 volts D. 114.8 volts
Last Answer : Answer: D
Description : If the total source voltage of the three-wire distribution system shown in the illustration is 240 volts, what is the voltage across load L2? [NOTE: Kirchhoff's voltage and current laws apply.] EL-0075 A. 110.4 volts B. 112.2 volts C. 113.0 volts D. 114.8 volts
Last Answer : Answer: C
Description : If the total source voltage of the three-wire distribution system shown in the illustration is 240 volts, what is the voltage across load L3? [NOTE: Kirchhoff's voltage and current laws apply.] EL-0075 A. 110.4 volts B. 112.2 volts C. 113.0 volts D. 114.8 volts
Last Answer : Answer: B
Description : If the total source voltage of the three-wire distribution system shown in the illustration is 240 volts, what is the voltage across load L1? [NOTE: Kirchhoff's voltage and current laws apply.] EL-0075 A. 110.4 volts B. 112.2 volts C. 113.3 volts D. 114.8 volts
Description : Figure 'D' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts
Last Answer : Answer: A
Description : Figure 'C' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts
Description : Figure 'B' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts
Description : Figure 'A' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts
Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 110 ohms, and R2 is 10 kohms what is the voltage measured across R1 EL-0036 A. 11.86 volts B. .131 volts C. 12 volts D. .673 volts
Description : If the line voltage to the controller shown in the illustration is 440 volts, what is applied across the control circuit? EL-0080 A. 110 volts B. 220 volts C. 440 volts D. 660 volts
Description : If the line voltage to the controller shown in the illustration is 440 volts, what voltage is applied across the motor when contacts 'S' close? EL-0080 A. 110 volts B. 220 volts C. 440 volts D. 660 volts
Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 220 volts were applied to terminals 'H1' & 'H2', what would be indicated across 'X1' & 'X4' with 'X2' & 'X3' connected and isolated? EL-0082 A. 55 volts B. 110 volts C. 220 volts D. 440 volts
Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 110 volts were applied to terminals 'X1,3' and 'X2,4', what would be indicated across 'H1' and 'H2'? EL-0082 A. 27.5 volts B. 55 volts C. 220 volts D. 440 volts
Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 440 volts were applied to terminals 'H1' & 'H2', what would be indicated across 'X1' & 'X4' with 'X2' & 'X3' connected and isolated? EL-0082 A. 110 volts B. 220 volts C. 880 volts D. 1760 volts
Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 220 volts were applied to terminals 'H1' and 'H2', what would be indicated across 'X3' and 'X4'? EL-0082 A. 55 volts B. 110 volts C. 440 volts D. 880 volts
Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 440 volts were applied to terminals 'H1' and 'H2', what would be indicated across 'X1,3' and 'X2,4'? EL-0082 A. 55 volts B. 110 volts C. 220 volts D. 880 volts
Description : The turns ratio of transforme 'A' shown in the illustration is four to one and all taps are evenly spaced. If 110 volts were applied to terminals 'X1' and 'X3', what would be indicated across 'H1' and 'H2'? EL-0082 A. 37.5 volts B. 55 volts C. 220 volts D. 440 volts
Description : The turns ratio of device 'A' shown in the illustration is four to one and all taps are evenly spaced. If 110 volts were applied to terminals 'X1' and 'X3', what would be indicated across 'H1' and 'H2'? EL-0082 A. 37.5 volts B. 55 volts C. 220 volts D. 440 volts
Description : The turns ratio of device 'A' shown in the illustration is four to one and all taps are equally spaced. If 440 volts were applied between 'H1' and 'H4', what would appear across 'X1' and 'X4'? EL-0082 A. 110 volts B. 220 volts C. 440 volts D. 1760 volts
Description : What would be the voltage drop across the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts
Description : What would be the voltage drop across the parallel branches of the circuit shown in the illustration if the source is 30 volts the resistance for R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts
Description : If 450 volts AC were measured across the load as shown in the illustration it would indicate a/an _______________. EL-0083 A. open winding between 'H1' and 'X1' B. properly operating circuit C. open winding between 'X1' and 'X4' D. ground on one side of 'Ep'
Description : If fuse #1 shown in the illustration is defective, a voltage tester connected across points 'C' and 'B' will ____________. EL-0062 A. show a reading of 55 volts B. show full line voltage ... C. give positive indication that fuse #2 is good D. give positive indication that fuse #1 is defective
Description : In the illustration, if the device in figure 'A' has a step-up ratio of 10 to 1, what voltage should be measured at the secondary shortly after the primary of the device is connected to 110 volts DC? EL-0059 A. 0 volts B. 110 volts C. 11 volts D. 1100 volts
Description : What will be the total output voltage if four 1.5 volt batteries are connected in a series-parallel arrangement as shown in the illustration? EL-0039 A. 1.5 volts B. 3.0 volts C. 4.5 volts D. 6.0 volts
Description : What is the load voltage 'Es' as shown in the illustration? EL-0083 A. 292 volts B. 360 volts C. 450 volts D. 810 volts
Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 110 ohms, and R2 is 10 kohms what is the total power consumed by the circuit? EL-0036 A. 3.6 watts B. 72 watts C. .0011286 watts D. .014243 watts
Description : What would be the total power consumed in the circuit shown in the illustration if the source is 30 volts the resistance for R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms? EL-0032 A. 10 watts B. 40 watts C. 45 watts D. 60 watts
Description : What would be the total current flowing in the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 1 amp B. 2 amps C. 5 amps D. 15 amps
Description : The distance between a generator and its load is 100 feet. What would be the approximate total voltage drop across a two wire supply cable if the current were 5.5 amperes and the resistance of the wire were 2.525 ohms per 1,000 feet? A. 0.5 volts B. 1.38 volts C. 1.90 volts D. 2.77 volts
Description : What is the calculated voltage at the positive and negative terminals of the battery shown in the illustration if each cell has a voltage of 1.5 volts? EL-0034 A. 1.5 volts B. 3.0 volts C. 6.0 volts D. 12.0 volts
Description : When the circuit shown in the illustration is operating correctly, the voltage at the reference electrode will be kept in the optimum range of ____________. EL-0090 A. 0.01 - 0.05 volt B. 0.80 - 0.85 volt C. 35 - 60 volts D. 100 - 115 volts
Description : The turns ratio of device 'A' shown in the illustration is four to one and all the taps are equally spaced. If 120 volts were applied between 'X1' and 'X2', what would be indicated across 'H1' and 'H4'? EL-0082 A. 30 volts B. 120 volts C. 480 volts D. 1440 volts
Description : What is the median of 112 145 146 165 163 141 112 134 113 114 125.?
Last Answer : The median is 134.
Description : What is the median of 112 135 124 115 119 90 112 134 113 114 115.?
Last Answer : The median is 115.
Description : In the illustration, 12 volts is applied to the circuit where the resistance of R1 is 10 ohms and R2 is 10 ohms. what is the voltage across R2? EL-0036 A. 1.2 volts B. 2 volts C. 6 volts D. 12 volts
Description : In the illustration, the diode between terminals 16 and 17 is to _________. EL-0046 A. act as a short circuit for the sensing coil when CEMF is applied B. insure that the voltage across the coil does not exceed 9 volts C. improve response time D. act as a filter to prevent hunting
Description : Considering the function of the circuit shown in the illustration, what is the purpose of supplying the thrust lever potentiometers with both (+) and (-) 15 volts? EL-0095 A. To select which ... alternate voltage supply if the other fails. D. So as to automatically select the position of Relay #
Description : What would be the power consumed in the combined parallel section of the circuit shown in the illustration if the source were 30 volts and the resistance for R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts
Description : What power would be consumed by the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts
Description : What power would be consumed in EACH of the branch resistors of the circuit shown in the illustration if the source is 30 volts, the resistance for R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts
Description : What is the purpose of each of the 'signal conditioners' (6000F085 / AH170 / F125) shown in the illustration? EL-0094 A. Convert the varying signal from its particular sensor and deliver a ... the 'setpoint module' in order to keep the pressure or temperature at its sensor at set limits.
Description : When a voltage of 112 VDC is applied to the circuit illustrated with a resistance of 110 ohms the current will be________. EL-0018 A. .982 amps B. 1.018 amps C. 2.018 amps D. .222 amps
Description : If the illustrated device has a step-up ratio of 10 to 1 what voltage be measured at the secondary shortly after the primary of the device is connected to 110 volts DC with a current of 12 amps? EL-0055 A. 0 volts B. 110 volts C. 1000 volts D. 1100 volts
Description : The purpose of the automatic bus transfer shown in the illustration is to ___________. EL-0014 A. stepdown voltage to the lighting distribution panel B. provide emergency power to ... emergency switchboard from the main switchboard D. provide overcurrent protection to the lighting distribution panel
Description : As shown in the illustration, which set of conditions, evident to the operator and the 'setpoint module' respectively, will result in a high exhaust temperature alarm on the 'starboard main engine'? EL-0094 A. 50°F and 3.3 volts B. 180°F and 6.0 volts C. 750°F and 0-10 volts D. 900°F and 7.5 volts
Description : What is the purpose of either 'setpoint module' (6000F090/030) shown in the illustration? EL-0094 A. Program the 'signal conditioner' as to how to vary its input. B. Supply 0 - 10 volts to ... . Obtain an input from the 'signal conditioner' and, if outside set limits, signals the 'annunciator'.
Description : A load with an impedance of 440 ohms is connected across the secondary of the transformer illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given
Description : A load with an impedance of 440 ohms is connected across the secondary of the device illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given
Description : Money bill has been defined in - (1) (1) Article 110 (2) (2) Article 111 (3) Article 112 (4) Artcle 113
Last Answer : (1) Article 110 Explanation: Article 110 - definition of money bills Article 111 - Assent to Bills Article 112 - Annual financial statement Article 113 - Procedure in Parliament with respect to estimates