What are the different methods of contouring? Describe any one method along with sketch . Also write the situation where it is suitable

What are the different methods of contouring? Describe any one method along with sketch . Also write the situation where it is suitable
by

1 Answer

Answer :

There are two methods of contouring:-

1. Direct Method

2. Indirect Method – a. By squares

 b. By cross section

 c. By tacheometric

Direct method of contouring – In this method of contouring, the contours of required reduced level are plotted on ground itself. The procedure of direct method of contouring is as follows

image

Figure No. 1: Direct Method of Contouring


1. Set the level instrument at the center O as shown in figure 1 and do all temporary adjustments like levelling and focusing. 2. Take the first reading on bench mark (Reduced Level i.e. R.L. 100 m) as back sight reading (Say 1.200 m), so that R.L. of instrument axis will become 101.200 m. 3. If the contour of 100 m is required to plot, then reading on staff should be 101.200 – 100 = 1.200 m. 4. This reading of 1.200 m is searched in radial directions (say 300 around instrument station O) by looking through telescope of level instrument. Once these points are found out, then they are marked with red coloured pegs. 5. Similarly, to set 99, 98, and 97 m contour, the reading on staff should be 2.2, 3.2 and 4.2 m respectively. These all contours can be searched in same radial directions and then marked with blue, green and yellow coloured pegs respectively. 6. By joining these identical coloured pegs, we get the required contours on ground by this direct method of contouring. 

by

Related questions

Explain direct method of contouring.

Description : Explain direct method of contouring.

Last Answer : Direct method of contouring - In this method of contouring, the contours of required reduced level are plotted on ground itself. The procedure of direct method of contouring is as follows. ... identical coloured pegs, we get the required contours on ground by this direct method of contouring. 

State Direct & indirect method of contouring.Explain tacheometric method.

Description : State Direct & indirect method of contouring.Explain tacheometric method.

Last Answer : Method of contouring are: 1.Direct method 2 Indirect methods which include a)by cross section b)by squares c) tachometric contouring method. Tachometric contouring method. 1.This method ... calculated by tacheometry formulae. 4 The survey is plotted and then contour lines are interpolated. 

State the component parts of micro optic theodolite . How it is superior to a transit theodolite. Also write the situation where it is suitable.

Description : State the component parts of micro optic theodolite . How it is superior to a transit theodolite. Also write the situation where it is suitable.

Last Answer : Component parts of micro optic theodolite 1) Telescope 2) Magnification with standard eyepiece. 3) Level tube 4) Foot screws. 5) Tribatch & Trivet 6) Optical micrometer 7) Changing nob 8) ... is most suitable 3) This instrument is durable for harsh environments. 4) It is simple in use.

Describe the method of setting out simple curve by using the method of offset from long chord with sketch.

Description : Describe the method of setting out simple curve by using the method of offset from long chord with sketch. 

Last Answer : Given data: Direction of two straights, chainage of point of intersection, radius of curve. Procedure:  1) Set theodolite over B and measure deflection angle Ф  2) Calculate tangent length by ... equal to tangent length.  4) Divide long chord into even number of equal parts.     

Define grade contour. Give the procedure to locate grade contour on contour map with suitable sketch.

Description : Define grade contour. Give the procedure to locate grade contour on contour map with suitable sketch.

Last Answer : Grade Contour - It is the contour established on a specific grade or gradient along the hill side. OR   The line joining the points of equal grade or gradient is termed as grade contour.  ... all the marked points will give us the required grade contour of 1 in 30 accurately. 

Which of the following methods of contouring is most suitable for a hilly terrain? (A) Direct method (B) Square method (C) Cross-sections method (D) Tachometric method

Description : Which of the following methods of contouring is most suitable for a hilly terrain? (A) Direct method (B) Square method (C) Cross-sections method (D) Tachometric method

Last Answer : (D) Tachometric method

State the methods of locating contours and explain direct method.

Description : State the methods of locating contours and explain direct method.

Last Answer : Methods of locating contours :- 1) Direct method 2) Indirect method i) By cross section ii) By Squares (Block Contouring) iii) Tachometric Method Direct method of contouring:- In ... identical coloured pegs, we get the required contours on ground by this direct method of contouring.

Compare theodolite traversing by included angle method with deflection angle method. Which one is suitable?

Description : Compare theodolite traversing by included angle method with deflection angle method. Which one is suitable?

Last Answer : Sr.No. Included angle method of traversing  Deflection angle method of traversing 1 This method is most suitable for closed traverse. This method is most suitable for open traverse. ... is suitable for long narrow strip like survey of roads, rivers, canals, railways, etc.

Explain the principle of techeometry with the help of a neat sketch.

Description : Explain the principle of techeometry with the help of a neat sketch.

Last Answer : Principle of tacheometry is based on principle of similar triangle in which corresponding sides & altitudes are proportional The ratio of distance of base from apex and length of base is always constant. ... S3=f/i=Constant Where f=focal length of objective and i =stadia intercept  

Define tacheometry. State the principle of tacheometry with sketch.

Description : Define tacheometry. State the principle of tacheometry with sketch.

Last Answer : Tacheometry : It is the branch of angular surveying in which horizontal and vertical distances are determined from instrumental observations only, is known as tacheometry. Principle of tacheometry : ... to corresponding staff intercept remains constant as shown below in figure 3

In a contour map, if contours are crossing each other, what will be nature of topography? Draw the sketch to support your answer.

Description : In a contour map, if contours are crossing each other, what will be nature of topography? Draw the sketch to support your answer.

Last Answer : If contours are crossing or intersecting each other, then there is overhanging cliff as shown in figure 1 below.

Draw a neat sketch of simple curve showing all elements.

Description : Draw a neat sketch of simple curve showing all elements.

Last Answer : Simple curve

State the principle of EDM with sketch.

Description : State the principle of EDM with sketch.

Last Answer : Principle of EDM:- The fig shows a survey line AB, the length D of which is to be measured using EDM equipment placed at ends A. Let a transmitter be placed at A to propagate electromagnetic waves towards B ... measured at A. This will require EDM timing devices with an accuracy of 1 10-9s.  

sketch of simple circular curve and show notation there on

Description : sketch of simple circular curve and show notation there on

Last Answer : Let the distance between P and Q be D' which is to be measured. A wave transmitted from the transmitter at station P' with certain phase angle. There is a ... phase angle. For finding the distance, the phase difference between transmitted wave is measured and converted into distance.

Draw neat sketch of simple circular curve and show notation there on.

Description : Draw neat sketch of simple circular curve and show notation there on.

Last Answer : Sketch of simple circular curve and show notation there on :

Explain the working principal of EDM with a neat sketch.

Description : Explain the working principal of EDM with a neat sketch. 

Last Answer : Let the distance between P and Q be D' which is to be measured. A wave is transmitted from the transmitter at station P' with certain phase angle. . There ... finding the distance, the phase difference between transmitted wave and reflected wave is measured and converted into distance.

Draw neat sketch of contour for the following i)Hill ii) Valley iii)Gentle Slope iv) Ridge Line

Description : Draw neat sketch of contour for the following i)Hill ii) Valley iii)Gentle Slope iv) Ridge Line 

Last Answer : i)Hill ii) Valley iii)Gentle Slope iv) Ridge Line 

Describe any one method of orientation of plane table surveying

Description : Describe any one method of orientation of plane table surveying

Last Answer : Orientation by back sighting method: This method is accurate and is always preferred. Procedure: 1.Suppose A and B are two stations.The plane table is set up over A. The table is leveled by spirit level ... are perfect and needle is exactly at 0-0 , the orientation is said to be perfect.

Describe the method of locating contours by square method.

Description : Describe the method of locating contours by square method. 

Last Answer : 1) The method of square is indirect method of locating contours. 2) The method of squares is used where the area to be surveyed is small and not much undulating. 3) The area to be surveyed ... points are written on the respective corners. 6) The contours are then interpolated between them. 

Write principle of stadia method.

Description : Write principle of stadia method.

Last Answer : Principle of stadia method: The stadia method is based on the principle that the ratio of the perpendicular to the base is constant in similar isosceles triangles. In figure, let two ... stadia interval factor and the constant (f + d) is known as the additive constant of the instrument

Compare radiation and intersection methods of plane table surveying on any two parameters.

Description : Compare radiation and intersection methods of plane table surveying on any two parameters. 

Last Answer : Radiation method Intersection method 1. It requires the plane table to occupy a single station.  1. This method requires setting the table up at minimum of two stations.  ... for locating inaccessible points by the intersection of the rays drawn from two instruments stations. 

State the methods of contour interpolation and explain in brief any one.

Description : State the methods of contour interpolation and explain in brief any one.

Last Answer : Methods of interpolation:- i) By Arithmetic calculations ii) By Estimation iii) By Graphical method i) By Arithmetic Calculation: This is very tedious but accurate method and is used for small areas ... in fig.) may now be pricked through the position of the contour points on line PQ.

State the two methods of setting out curves.

Description : State the two methods of setting out curves.

Last Answer : Methods of setting out curves :- 1) Method of offsets or ordinates from the long chord 2) By successive bisection of arcs 3) By offsets from tangents 4) By offsets from chords produced 5) Rankine’s method of tangential angles 6) Two Theodolite method

State methods of locating contours and explain any one.

Description : State methods of locating contours and explain any one.

Last Answer : Following are the methods of locating contours 1. Direct Method. 2. Indirect method.  a) By Square / Block Contouring  b) By Cross Section  c) Tacheometric Contouring ... squares are plotted and reduced levels are written at their corners and the contours lines are then interpolated.

Define interpolation of contour and state its methods.

Description : Define interpolation of contour and state its methods. 

Last Answer : The process of spacing the contours proportionately between the ground points is known as “Interpolation of Contours”. The contours may be interpolated by: 1. Estimation 2. Arithmetical calculations. 3. Graphical method.

List three methods of fuel injection. Describe sequential method with suitable sketch.

Description : List three methods of fuel injection. Describe sequential method with suitable sketch.

Last Answer : Methods of petrol injection 1. Sequential fuel injection. (SFI) 2. Grouped fuel injection. 3. Simultaneous fuel injection 4. Continuous injection.  Sequential Injection: Each injector ... to crank/ camshaft position and pulse width, can be optimized for each individual cylinder.

Direct method of contouring is (A) A quick method (B) Adopted for large surveys only(C) Most accurate method (D) Suitable for hilly terrains

Description : Direct method of contouring is (A) A quick method (B) Adopted for large surveys only (C) Most accurate method (D) Suitable for hilly terrains

Last Answer : (C) Most accurate method

Give the simplest method of finding the area of zero of a zero circle from manufacturers table.

Description : Give the simplest method of finding the area of zero of a zero circle from manufacturers table.

Last Answer : The area of zero circle can be find out simply by using following formula. A = M x C Where, A = Area of zero circle  M = Multiplier or multiplying constant provided in manufacturers table C = Constant of planimeter provide in manufacturers table

Explain the setting of curve by Rankine’s deflection angle method.

Description : Explain the setting of curve by Rankine’s deflection angle method.

Last Answer : Rankine's deflection angle Method:-  1) Set up theodolite at first tangent point, T1 and level it carefully, set the vernier A to 3600 2) bisect the ranging rod at the point of ... . The angle thus obtained will be set on the vernier of the theodolite for setting out the curve.

State the errors eliminated by repetition method.

Description : State the errors eliminated by repetition method. 

Last Answer : The errors eliminated by repetition method are : 1) Errors due to eccentricity of verniers and centers are eliminated by taking the both vernier readings and averaging them. 2) Errors due to ... bisection of object may compensate each other. 5) Errors due to improper levelling can be minimized 

State the procedure of measurement of horizontal angle by repetition method.

Description : State the procedure of measurement of horizontal angle by repetition method. 

Last Answer : The horizontal angle is measured very precisely using method of repetition as follows : 1) Set-up the theodolite over station O and level it properly. 2) Set the vernier A and vernier B at 0°0'0 ... repeat the same procedure. 9) The mean of both angles gives the horizontal angle AOB. 

Explain the procedure of curve setting by method of offsets from long chord

Description : Explain the procedure of curve setting by method of offsets from long chord

Last Answer : Procedure: 1. Divide the long chord into an even number of equal parts say 8,10,12 etc. 2. Set out the offset as calculated from the formula  and obtain the required points on the ... ED, the offset for the right half of the curve will be the same as those on the left half side. 

State the procedure for measuring a horizontal angle by method of repetition.

Description : State the procedure for measuring a horizontal angle by method of repetition.

Last Answer : Procedure : 1. Set up the instrument over Q and level it accurately with the telescope in the normal position. 2. Set the vernier A to 360o. Loosen the lower clamp direct the telescope ... final reading by three. 14. By taking average of both the face, horizontal angle PQR is obtained.

Explain the method of repetition to measure horizontal angle using transit theodolite.

Description : Explain the method of repetition to measure horizontal angle using transit theodolite. 

Last Answer : Procedure: 1 Suppose the angle AOB is to be measured by the repetition process. The theodolite is set over O. The instrument is centered and levelled properly.Vernier A is set at 00 and vernier is at 1800 ... 8 The mean of the two angles obtained from two faces gives the actual angle AOB. 

Describe stepwise procedure to prepare the layout of a small building using total station.

Description : Describe stepwise procedure to prepare the layout of a small building using total station.

Last Answer : Layout of small building by using total station: 1. On the plan supplied by an architect, number the column serially from left to right and top to bottom starting from top left ... of setting out by comparing the diagonal distance between the extreme column centres to their calculated values.

Describe the procedure to determine co-ordinates of a station using GPS.

Description : Describe the procedure to determine co-ordinates of a station using GPS. 

Last Answer : The following are some general GPS field survey procedures that should be performed at each station, observation, and/or session on a GPS survey. A. Receiver setup : GPS receiver shall be set up ... is to identify any problem that may exist which can be corrected before returning from the field.  

Describe the use of digital theodolite for measurement of horizontal and vertical angle.

Description : Describe the use of digital theodolite for measurement of horizontal and vertical angle.

Last Answer : I) Procedure for measurement of horizontal angle with digital theodolite: 1) Taking out digital theodolite for box and fix it on tripod over required station. 2) Approximate leveling by leg adjustment and ... and take the reading at B. 9) Difference of two angle gives required vertical angle AOB

Describe the temporary adjustment of digital level.

Description : Describe the temporary adjustment of digital level.

Last Answer : Temporary adjustment of digital level:- 1) Setup stability:- The digital level should be fixed by rotating its screw head on top of tripod stand. Set tripod legs wide apart to increase the stability ... several times if required. 5) Focus the telescope properly to get clear image of cross hairs .

Describe the procedure for setup of total station.

Description : Describe the procedure for setup of total station.

Last Answer : Following steps are followed for the set up of total station 1. Set up the tripod approximately over the station point. 2. Remove the plastic cap from tripod and make tripod nearly level by stretching ... 7.Focusing of object glass. 8.Check the plate level from time to time during measurement .

Describe the procedure to locate grade contour in field

Description : Describe the procedure to locate grade contour in field 

Last Answer : Line joining the point along the same gradient is called contour gradient or grade contour. All the points on a contour have the same elevation. But all the points on a contour gradient do not ... on contour of RL 64. Similarly others points are established to obtain the grade contour on field.

Describe layout of small building by using total station.

Description : Describe layout of small building by using total station. 

Last Answer : Layout of small building by using total station: 1. On the plan supplied by an architect, number the column serially from left to right and top to bottom starting from top left corner ... setting out by comparing the diagonal distance between the extreme column centres to their calculated values. 

Describe the temporary adjustment of theodolite

Description : Describe the temporary adjustment of theodolite

Last Answer : Temporary adjustment of theodolite:- The following operations should be done as temporary adjustments before taking readings on any theodolite. 1. Setting of theodolite on tripod stand - The theodolite ... .e. cross hairs and object) simultaneously focussing of telescope is said to be completed. 

Write the use of Gale’s table.

Description : Write the use of Gale’s table.

Last Answer : Gale’s traverse table is useful to find out independent coordinates of theodolite traverse by applying necessary corrections to consecutive co-ordinates of the same traverse. Further these independent co-ordinates are useful to draw the accurate traverse without linear and angular errors.

What is a contour map? Write any two objects of preparing contour map.

Description : What is a contour map? Write any two objects of preparing contour map.

Last Answer : Contour map : It the map showing nature of topography of any particular field with the help of contour lines indicating reduced levels of ground. Objects of preparing contour map : Contour map ... . 4. To excavate the canal and contour cut trenches along hillside under watershed management works.

Write down the procedure for determination of tacheometric constants.

Description : Write down the procedure for determination of tacheometric constants.

Last Answer : Method of determining tacheometric constants in the field1) A fairly level ground is selected. The tacheometer is set up at O and pegs are fixed at A, B & C, known distances apart. 2) The staff ... 5) By solving the equations in pairs, find tacheometric constants (f/i) and (f+d)

Write four applications of GIS.

Description : Write four applications of GIS.

Last Answer : Applications of GIS:- 1) Map making 2) Site selection 3) Mineral Exploration 4) Land use planning and management 5) Environmental Impact studies 6) Natural Hazard mapping or assessment 7) Water Resources availability.

Enlist any eight components of transit theodolite and write their functions.

Description : Enlist any eight components of transit theodolite and write their functions.

Last Answer : Components of transit theodolite and their functions - Sr.No. Component Function 1 Leveling head  To support the main working parts of the instrument and screws on to a tripod.  ... movement of upper plate.  14 Spindles Inner spindle and outer spindles are coaxial. 

Mention different sources of errors in theodolite surveying.

Description : Mention different sources of errors in theodolite surveying.

Last Answer : Sources of errors in theodolite surveying:- i) Instrumental errors1) Non adjustment of plate bubble. 2) Line of collimation not being perpendicular to horizontal axis. 3) Line of collimation ... causes error due to irregular refraction. 2) High winds cause vibration in instrument.

What are the different fundamental axes of theodolite?

Description : What are the different fundamental axes of theodolite?

Last Answer : line of collimation

State different relationship between fundamental lines of theodolite.

Description : State different relationship between fundamental lines of theodolite.

Last Answer : When the instrument is in perfect adjustment, the following relations should exists: 1) The axis of the plate level must be perpendicular to the vertical axis. 2) The line of collimation ... collimation. 5) The vernier of vertical circle must read zero when the telescope is perfectly horizontal.