A shunt-type voltage regulator is connected in serial/parallel (which one) with the load resistance.

A shunt-type voltage regulator is connected in serial/parallel (which one) with the load resistance.
by

1 Answer

Answer :

In parallel.
by

Related questions

A shunt type voltage regulator is connected in series/parallel with the load resistance.

Description : A shunt type voltage regulator is connected in series/parallel with the load resistance.

Last Answer : Parallel

The simplest method of controlling the terminal voltage of compound-wound DC generator is with a _____________. A. hand-operated field rheostat connected in series with the shunt field circuit B. separate exciter in a series with the shunt field C. carbon pile regulator in series with the load D. balance coil diverting neutral current through the shunt field

Description : The simplest method of controlling the terminal voltage of compound-wound DC generator is with a _____________. A. hand-operated field rheostat connected in series with the shunt field circuit B. ... in series with the load D. balance coil diverting neutral current through the shunt field

Last Answer : Answer: A

In a full-wave voltage doubler, are the capacitors connected in series or in parallel with the output load?

Description : In a full-wave voltage doubler, are the capacitors connected in series or in parallel with the output load?

Last Answer : In parallel.

When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease (which one) in the resistance of the regulating device.

Description : When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease (which one) in the resistance of the regulating device.

Last Answer : An increase.

When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease in the resistance of the regulating device.

Description : When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease in the resistance of the regulating device.

Last Answer : Increase.

Regarding an AC generator connected to the main electrical bus; as the electric load and power factor vary, a corresponding change is reflected in the generator armature reaction. These changes in armature reaction are compensated for by the __________ A. governor speed droop setting B. voltage regulator C. balance coil D. phase-balance relay

Description : Regarding an AC generator connected to the main electrical bus; as the electric load and power factor vary, a corresponding change is reflected in the generator armature reaction. These changes in ... . governor speed droop setting B. voltage regulator C. balance coil D. phase-balance relay

Last Answer : Answer: B

Which of the methods listed is used to maintain the division of load between two compound-wound, DC generators operating in parallel? A. The shunt fields are interconnected. B. The shunt field rheostats are interconnected. C. The series fields of both generators are connected in series. D. The equalizer connection parallels the series fields of all machines.

Description : Which of the methods listed is used to maintain the division of load between two compound-wound, DC generators operating in parallel? A. The shunt fields are interconnected. B. The shunt ... generators are connected in series. D. The equalizer connection parallels the series fields of all machines.

Last Answer : Answer: D

Which of the following meters uses a shunt connected in series with the load, but parallel with the meter movement? A. voltmeter B. power factor meter C. wattmeter D. ammeter

Description : Which of the following meters uses a shunt connected in series with the load, but parallel with the meter movement? A. voltmeter B. power factor meter C. wattmeter D. ammeter

Last Answer : Answer: D

The shunt of a DC ammeter should be connected in __________. A. series with the load and in parallel with the meter movement B. parallel with the load and in series with the meter movement C. parallel with the load and in parallel with the meter movement D. series with the load and in series with the meter movement

Description : The shunt of a DC ammeter should be connected in __________. A. series with the load and in parallel with the meter movement B. parallel with the load and in series with the meter movement C. ... and in parallel with the meter movement D. series with the load and in series with the meter movement

Last Answer : Answer: A

Which of the listed meters uses a shunt connected in series with the load, but parallel with the meter movement? A. Voltmeter B. Power factor meter C. Ammeter D. Wattmeter

Description : Which of the listed meters uses a shunt connected in series with the load, but parallel with the meter movement? A. Voltmeter B. Power factor meter C. Ammeter D. Wattmeter

Last Answer : Answer: C

Which of the methods listed is used to maintain equal load sharing between two compound wound DC generators operating in parallel? A. The shunt fields are interconnected. B. The shunt field rheostats are interconnected. C. The series fields of both generators are connected in series. D. The series fields of both generators are connected in parallel.

Description : Which of the methods listed is used to maintain equal load sharing between two compound wound DC generators operating in parallel? A. The shunt fields are interconnected. B. The shunt field rheostats ... are connected in series. D. The series fields of both generators are connected in parallel.

Last Answer : Answer: D

The shunt used in an ammeter should be connected in ____________. A. series with the load and in parallel with the meter movement B. parallel with the load and in series with the meter movement C. parallel with the load and in parallel with the meter movement D. series with the load and in series with the meter movement

Description : The shunt used in an ammeter should be connected in ____________. A. series with the load and in parallel with the meter movement B. parallel with the load and in series with the meter movement C. ... in parallel with the meter movement D. series with the load and in series with the meter movement

Last Answer : Answer: A

A good choice of shunt resistance will place the indicating pointer near what part of the meter scale with a normal load?

Description : A good choice of shunt resistance will place the indicating pointer near what part of the meter scale with a normal load?

Last Answer : Midscale.

When a resistor is used as a shunt and is connected in parallel with a meter movement coil, it will provide _____________. A. a measurement of circuit resistance B. an increased accuracy of approximately 1.5 percent C. an extended meter range D. none of the above

Description : When a resistor is used as a shunt and is connected in parallel with a meter movement coil, it will provide _____________. A. a measurement of circuit resistance B. an increased accuracy of approximately 1.5 percent C. an extended meter range D. none of the above

Last Answer : Answer: C

For a diode to act as a rectifier, should it be connected in series or parallel with the load?

Description : For a diode to act as a rectifier, should it be connected in series or parallel with the load?

Last Answer : Series.

Serial-to-parallel and parallel-to-serial conversions are accomplished by what type of circuit?

Description : Serial-to-parallel and parallel-to-serial conversions are accomplished by what type of circuit?

Last Answer : Shift register.

The purpose of a voltage regulator is to provide an output voltage with little or no __

Description : The purpose of a voltage regulator is to provide an output voltage with little or no __

Last Answer : Variation.

The purpose of a voltage regulator is to provide an output voltage with little or no _

Description : The purpose of a voltage regulator is to provide an output voltage with little or no _

Last Answer : Variation.

Three resistors connected in parallel have values of 12 kΩ, 20kΩ, and 30kΩ. What is the equivalent resistance? A37. 6kΩ Q38. Two resistors connected in parallel have values of 10 kΩ and 30kΩ. What is eht equivalent resistance?

Description : Three resistors connected in parallel have values of 12 kΩ, 20kΩ, and 30kΩ. What is the equivalent resistance? A37. 6kΩ Q38. Two resistors connected in parallel have values of 10 kΩ and 30kΩ. What is eht equivalent resistance?

Last Answer : 7.5kΩ

Four equal resistors are connected in parallel, each resistor has an ohmic value of 100 ohms, what is the equivalent resistance?

Description : Four equal resistors are connected in parallel, each resistor has an ohmic value of 100 ohms, what is the equivalent resistance?

Last Answer : 25 ohms

What structurally large, low-resistance conductor is connected in parallel with the meter movement to prevent damage?

Description : What structurally large, low-resistance conductor is connected in parallel with the meter movement to prevent damage?

Last Answer : Shunt.

Current measuring instruments must always be connected in _____________. A. series with a circuit B. parallel with a circuit C. series-parallel with a circuit D. delta with the shunt

Description : Current measuring instruments must always be connected in _____________. A. series with a circuit B. parallel with a circuit C. series-parallel with a circuit D. delta with the shunt

Last Answer : Answer: A

A DC shunt generator has its field windings connected in _____________. A. series with the series windings B. parallel with the field rheostat C. series with the armature windings D. parallel with the armature windings

Description : A DC shunt generator has its field windings connected in _____________. A. series with the series windings B. parallel with the field rheostat C. series with the armature windings D. parallel with the armature windings

Last Answer : Answer: D

Which of the following types of DC motors has its field connected in parallel with its armature? A. Counter EMF B. Shunt C. Salient pole D. Series

Description : Which of the following types of DC motors has its field connected in parallel with its armature? A. Counter EMF B. Shunt C. Salient pole D. Series

Last Answer : Answer: B

When securing an AC generator, you should FIRST ___________. A. open the generator circuit breaker B. switch the voltage regulator to 'manual' C. decrease the field excitation to minimum D. reduce the load on the unit

Description : When securing an AC generator, you should FIRST ___________. A. open the generator circuit breaker B. switch the voltage regulator to 'manual' C. decrease the field excitation to minimum D. reduce the load on the unit

Last Answer : Answer: D

The instantaneous reduction in voltage of an AC generator, resulting from an increase in load, and prior to the automatic voltage regulator correcting the situation, is called voltage ____________. A. droop B. drop C. dip D. regulation

Description : The instantaneous reduction in voltage of an AC generator, resulting from an increase in load, and prior to the automatic voltage regulator correcting the situation, is called voltage ____________. A. droop B. drop C. dip D. regulation

Last Answer : Answer: C

A zener voltage regulator has load requirements of 12 V and 2 A. The zener diode minimum current

Description : A zener voltage regulator has load requirements of 12 V and 2 A. The zener diode minimum current requirement is 0.2 A. The minimum voltage at input is 24 V. What is the required value of series resistance with source? A) 5.45 Ω B) 6 Ω C) 7.2 Ω D) 6.38 Ω  

Last Answer : A zener voltage regulator has load requirements of 12 V and 2 A. The zener diode minimum current requirement is 0.2 A. The minimum voltage at input is 24 V. What is the required value of series resistance with source? A) 5.45 Ω B) 6 Ω C) 7.2 Ω D) 6.38 Ω  

When shipboard electrical distribution circuits are connected in parallel, additional parallel circuits will cause the total circuit resistance to _____________. A. increase, causing a drop in the line current B. increase, causing a decrease in the line voltage C. decrease, causing an increase in the line voltage D. decrease, causing an increase in the line current

Description : When shipboard electrical distribution circuits are connected in parallel, additional parallel circuits will cause the total circuit resistance to _____________. A. increase, causing a drop in the line current B ... an increase in the line voltage D. decrease, causing an increase in the line current

Last Answer : Answer: D

The cycles per second developed by the alternator aboard your vessel is determined by _____________. A. the speed of the engine driving the alternator B. the resistance applied to the field rheostat C. the synchronous speed of induction D. the adjustments made to the voltage regulator

Description : The cycles per second developed by the alternator aboard your vessel is determined by _____________. A. the speed of the engine driving the alternator B. the resistance applied to the field rheostat C. the synchronous speed of induction D. the adjustments made to the voltage regulator

Last Answer : Answer: A

Which of the following statements represents the correct method of connecting the shunt of an ammeter prior to taking a reading? A. In series with the load and in series with the meter movement. B. In series with the load and in parallel with the meter movement. C. In parallel with the load and in series with the meter movement. D. In parallel with the load and in parallel with the meter movement.

Description : Which of the following statements represents the correct method of connecting the shunt of an ammeter prior to taking a reading? A. In series with the load and in series with the meter movement. B. In ... with the meter movement. D. In parallel with the load and in parallel with the meter movement.

Last Answer : Answer: B

An adjustable resistor, whose resistance can be changed without opening the circuit in which it is connected, is called a _____________. A. bleeder resistor B. rheostat C. bridge D. variable shunt strip

Description : An adjustable resistor, whose resistance can be changed without opening the circuit in which it is connected, is called a _____________. A. bleeder resistor B. rheostat C. bridge D. variable shunt strip

Last Answer : Answer: B

A galvanometer of 65 Ω resistance gives full scale deflection with 4 mA current. In order to convert it into ammeter, the range of 10 A is connected with it, the shunt resistance should be a) 0.1 Ω b) 0.2 Ω c) 0.06 Ω d) 0.03 Ω

Description : A galvanometer of 65 Ω resistance gives full scale deflection with 4 mA current. In order to convert it into ammeter, the range of 10 A is connected with it, the shunt resistance should be a) 0.1 Ω b) 0.2 Ω c) 0.06 Ω d) 0.03 Ω

Last Answer : d) 0.03 Ω

To limit the current flow through a DC voltmeter to as low a value as possible, the moving coil circuit is provided with a/an _____________. A. high series resistance B. high parallel resistance C. series inductor D. external shunt

Description : To limit the current flow through a DC voltmeter to as low a value as possible, the moving coil circuit is provided with a/an _____________. A. high series resistance B. high parallel resistance C. series inductor D. external shunt

Last Answer : Answer: A

A d.c. shunt motor runs at no load speed of 1140 r.p.m. At full load, armature reaction weakens the main flux by 5% whereas the armature circuit voltage drops by 10%. The motor full load speed in r.p.m. is (A) 1080 (B) 1203 (C) 1000 (D) 1200

Description : A d.c. shunt motor runs at no load speed of 1140 r.p.m. At full load, armature reaction weakens the main flux by 5% whereas the armature circuit voltage drops by 10%. The motor full load speed in r.p.m. is (A) 1080 (B) 1203 (C) 1000 (D) 1200

Last Answer : (A) 1080

A dc shunt generator has a speed of 800 rpm when delivering 20 A to the load at the terminal voltage of 220V. If the same machine is run as a motor it takes a line current of 20A from 220V supply. The speed of the machine as a motor will be (A) 800 rpm. (B) more than 800 rpm. (C) less than 800 rpm. (D) both higher or lower than 800 rpm.

Description : A dc shunt generator has a speed of 800 rpm when delivering 20 A to the load at the terminal voltage of 220V. If the same machine is run as a motor it takes a line current of 20A from 220V supply. The speed of ... . (B) more than 800 rpm. (C) less than 800 rpm. (D) both higher or lower than 800 rpm.

Last Answer : (C) less than 800 rpm.

Shunt generator gives full voltage on load and the voltage drop as the load on the generator

Description : Shunt generator gives full voltage on load and the voltage drop as the load on the generator a. Decreases b. Increases c. Remains the same d. None of above 

Last Answer : Shunt generator gives full voltage on load and the voltage drop as the load on the generator a. Decreases b. Increases c. Remains the same d. None of above 

The terminal voltage of a DC shunt generator drops on load because of all of the following

Description : The terminal voltage of a DC shunt generator drops on load because of all of the following except : (A) Armature reaction (B) Armature resistance drop (C) Commutation (D) Field weakening due to armature reaction and armature resistance drop

Last Answer : (D) Field weakening due to armature reaction and armature resistance drop

A permanent magnet moving coil instrument gives full scale deflection of 25mA when a voltage of 75mV is applied across it. Calculate: (i) Resistance of shunt required for full scale deflection of 150 A. (ii) Series resistance for full scale deflection of 500 V.

Description : A permanent magnet moving coil instrument gives full scale deflection of 25mA when a voltage of 75mV is applied across it. Calculate: (i) Resistance of shunt required for full scale deflection of 150 A. (ii) Series resistance for full scale deflection of 500 V.

Last Answer : Answer :

Is an ammeter connected in series or in parallel with the circuit under test?

Description : Is an ammeter connected in series or in parallel with the circuit under test?

Last Answer : . In series.

When the axes of two connected fibers are no longer in parallel, the two connected fibers are in what kind of misalignment?

Description : When the axes of two connected fibers are no longer in parallel, the two connected fibers are in what kind of misalignment?

Last Answer : Angular misalignment.

Why will an ammeter be damaged if connected in parallel with the circuit to be measured?

Description : Why will an ammeter be damaged if connected in parallel with the circuit to be measured?

Last Answer : Since the ammeter has a small resistance compared to the load, it will have very high current if it is connected in parallel. This high current will damage the meter.

What is the purpose of the regulator section?

Description : What is the purpose of the regulator section?

Last Answer : To maintain a constant voltage to the load.

What is the purpose of the amperite regulator?

Description : What is the purpose of the amperite regulator?

Last Answer : Current regulation.

In an electron tube regulator, the electron tube replaces what component?

Description : In an electron tube regulator, the electron tube replaces what component?

Last Answer : Variable resistor.

What is the purpose of the regulator?

Description : What is the purpose of the regulator?

Last Answer : To maintain a constant voltage to the load.

If an ac voltmeter is connected between the S2 and S3 windings on a TX, at what two rotor positions should the voltmeter read maximum voltage?

Description : If an ac voltmeter is connected between the S2 and S3 windings on a TX, at what two rotor positions should the voltmeter read maximum voltage?

Last Answer : . 150º and 330º

If the reference point in question 25 were connected to ground, what would be the voltage level of the reference point?

Description : If the reference point in question 25 were connected to ground, what would be the voltage level of the reference point?

Last Answer : Zero volts.

A circuit has a source voltage of 100 volts and two 50-ohm resistors connected in series. If the reference point for this circuit is placed between the two resistors, what would be the voltage at the reference point?

Description : A circuit has a source voltage of 100 volts and two 50-ohm resistors connected in series. If the reference point for this circuit is placed between the two resistors, what would be the voltage at the reference point?

Last Answer : 50 volts.

In what manner are voltage-measuring instruments connected to the circuit to be measured?

Description : In what manner are voltage-measuring instruments connected to the circuit to be measured?

Last Answer : In parallel.

In a capacitor filter, is the capacitor in series or in parallel with the load?

Description : In a capacitor filter, is the capacitor in series or in parallel with the load?

Last Answer : Parallel.