What Are The Factors Affecting Endurance Strength?

What Are The Factors Affecting Endurance Strength?
by

1 Answer

Answer :

Factors affecting endurance strength are
1. Load ii. Surface finish
2. Size
3. Temperature
4. Impact
5. Reliability
by

Related questions

Explain Size Factor In Endurance Strength?

Description : Explain Size Factor In Endurance Strength?

Last Answer : Size factor is used to consider the effect of the size on endurance strength. A large size object will have more defects compared to a small one. So, endurance strength is reduced. If K is the size factor, then Actual endurance strength = Theoretical endurance limit x K

What Is Endurance Limit?

Description : What Is Endurance Limit?

Last Answer : Endurance limit or fatigue limit is the maximum stress that a member can with stand for an infinite number of load applications without failure when subjected to completely reversed loading.

Define Endurance Limit?

Description : Define Endurance Limit?

Last Answer : Endurance limit is the maximum value of completely reversed stress that the standard specimen can sustain an infinite number (106) of cycles without failure.

What Are The Factors That Affect Notch Sensitivity?

Description : What Are The Factors That Affect Notch Sensitivity?

Last Answer : The factors effecting notch sensitivity are: 1. Material 2. Notch radius 3. Size of component 4. Type of loading 5. Grain Structure

List Out The Factors Involved In Arriving At Factor Of Safety?

Description : List Out The Factors Involved In Arriving At Factor Of Safety?

Last Answer : The factors involved in arriving at factor of safety are: 1. Material properties 2. Nature of loads 3. Presence of localized stresses 4. Mode of failures

What Are The Factors To Be Considered In The Selection Of Materials For A Machine Element?

Description : What Are The Factors To Be Considered In The Selection Of Materials For A Machine Element?

Last Answer : While selecting a material for a machine element, the following factors are to be considered 1. Required material properties 2. Manufacturing ease 3. Material availability 4. Cost

A Bench Vice Has Which Type Of Thread?

Description : A Bench Vice Has Which Type Of Thread?

Last Answer : ACME

For Tight Leakage Joints, Which Type Of Thread Is Best Suited?

Description : For Tight Leakage Joints, Which Type Of Thread Is Best Suited?

Last Answer : NPT( National Pipe Threads)

What Is The Main Purpose Of A Gear Box In A Vehicle?

Description : What Is The Main Purpose Of A Gear Box In A Vehicle?

Last Answer : To vary the torque at the road vehicles.

Rankine’s And Guest’s Theory Of Failure Are Applicable For What Materials?

Description : Rankine’s And Guest’s Theory Of Failure Are Applicable For What Materials?

Last Answer : Rankine’s theory of failure is applicable for brittle materials. Guest’s theory of failure is applicable for ductile materials.

While Taking A Turn, What Action Differential Makes?

Description : While Taking A Turn, What Action Differential Makes?

Last Answer : An increase in the speed of the outer wheel.

How The Size Of The Gearis Usually Specified?

Description : How The Size Of The Gearis Usually Specified?

Last Answer : By pitch circle diameter.

What Is The Empirical Formula Used To Give The Number Of Bolts In Flange Coupling?

Description : What Is The Empirical Formula Used To Give The Number Of Bolts In Flange Coupling?

Last Answer : n = 0.2d + 3

The Critical Speed Of Rotating Shaft Depends Upon What?

Description : The Critical Speed Of Rotating Shaft Depends Upon What?

Last Answer : Mass and stiffness.

In Designing A Clutch Plate, What Assumption Is Made?

Description : In Designing A Clutch Plate, What Assumption Is Made?

Last Answer : Uniform wear condition is assumed because it leads to safer design.

On What Basis A Transmission Shaft Subjected To Bending Loads Must Be Designed?

Description : On What Basis A Transmission Shaft Subjected To Bending Loads Must Be Designed?

Last Answer : Maximum shear stress theory.

What Is The Constant Factor In Case Of R-10 Series Of Preferred Numbers?

Description : What Is The Constant Factor In Case Of R-10 Series Of Preferred Numbers?

Last Answer : 1.25

Why A Sleeve Is Fitted On A Ball Bearing?

Description : Why A Sleeve Is Fitted On A Ball Bearing?

Last Answer : To prevent relative axial movement between the shaft and the bearing.

A Wire Rope Is Designated As 6 X 19 Standard Hoisting. What Do The Numbers 6 X 19 Represent?

Description : A Wire Rope Is Designated As 6 X 19 Standard Hoisting. What Do The Numbers 6 X 19 Represent?

Last Answer : Number of strands x number of wires in each strand.

What Do You Mean By Allowance In Limits And Fits?

Description : What Do You Mean By Allowance In Limits And Fits?

Last Answer : Allowance in limits and fits refers to maximum clearance between shaft and hole.

Why Slenderness Ratio Is Considered In Design Of Members?

Description : Why Slenderness Ratio Is Considered In Design Of Members?

Last Answer : When length of the member is increased, the member may fail due to buckling even though the member is symmetrical in all respects and the load is concentric.

Can You Tell Something About Hazop Study?

Description : Can You Tell Something About Hazop Study?

Last Answer : In Hazop (Hazards and operatibility) study each and every conceivable process deviation from normal operating condition of a system having identical design intention, is thoroughly analysed for ... to mitigate hazard/operability problems are suggested on the basis of available protective system.

How Computer Helps In Designing?

Description : How Computer Helps In Designing?

Last Answer : Computer is able to store lot of information and same can be retrieved fast. It performs calculations very fast. The design can be visualized on screen and any alterations made and its effects ... . Thus optimum designs can be achieved much faster and these are thoroughly tested from all angles.

What Type Of Threads Are Used For Pressure Tight Joints And For Power Transmission?

Description : What Type Of Threads Are Used For Pressure Tight Joints And For Power Transmission?

Last Answer : Pipe threads are used for pressure tight joints and square threads for power transmission.

What Are The Common Profiles Used For Splines In Machine Elements?

Description : What Are The Common Profiles Used For Splines In Machine Elements?

Last Answer : The profiles used for splines in machine elements are straight sided splines, triangular splines and in volute splines.

Write The Torsion Equation?

Description : Write The Torsion Equation?

Last Answer : The torsional equation is, T/J = q/r = GӨ/L Where, T - Torsional moment (T is in N-mm) J - Polar moment of inertia (J is in mm⁴) q - Shear stress in the element (q is in N/mm²) r - Distance of element from ... (G is in N/mm²) Ө - Angle of twist (Ө is in radians) L - Length of the shaft (L is in mm)

Write The Bending Equation?

Description : Write The Bending Equation?

Last Answer : The bending moment equation is, M/I = f/y= E/R, Where, M – Bending moment (M is in N-mm) I - Moment of inertia about centroidal axis (I is in mm⁴) f – Bending Stress (f is in N/mm²) y - Distance from neutral axis (y is in mm) E - Young’s modulus (E is in N/mm²) R - Radius of curvature (R is in mm)

What Is Principle Stress And Principle Plane?

Description : What Is Principle Stress And Principle Plane?

Last Answer : A plane which has no shear stress is called principle plane the corresponding stress is called principle stress.

Give Some Example For Curved Beam?

Description : Give Some Example For Curved Beam?

Last Answer : C frame, crane hook.

What Is Curved Beam?

Description : What Is Curved Beam?

Last Answer : In curved beam the neutral axis does not coincide with the centroidal axis.

What Is An S-n Curve?

Description : What Is An S-n Curve?

Last Answer : N curve has fatigue stress on ‘Y’ axis and number of loading cycles in ‘X’ axis. It is used to find the fatigue stress value corresponding to a given number of cycles.

Define Mach Inability?

Description : Define Mach Inability?

Last Answer : It is the property of the material, which refers to a relative ease with which a material can be cut. It is measured in a number of ways such as comparing the tool life for cutting different material.

What Is The Use Of Goodman & Soderberg Diagrams?

Description : What Is The Use Of Goodman & Soderberg Diagrams?

Last Answer : They are used to solve the problems of variable stresses.

Explain Notch Sensitivity. State The Relation Between Stress Concentration Factor And Notch Sensitivity?

Description : Explain Notch Sensitivity. State The Relation Between Stress Concentration Factor And Notch Sensitivity?

Last Answer : Notch sensitivity (q) is the degree to which the theoretical effect of stress concentration is actually reached. The relation is, Kf = 1 + q (Kt-1)

Give Some Methods Of Reducing Stress Concentration?

Description : Give Some Methods Of Reducing Stress Concentration?

Last Answer : Some of the methods are: 1. Avoiding sharp corners. 2. Providing fillets. 3. Use of multiple holes instead of single hole 4. Undercutting the shoulder parts.

What Are Various Theories Of Failure?

Description : What Are Various Theories Of Failure?

Last Answer : The failure theories are: 1. Maximum principal stress theory. 2. Maximum shear stress theory. 3. Maximum principal strain theory.

What Are The Modes Of Fracture?

Description : What Are The Modes Of Fracture?

Last Answer : The different the modes of fractures are: 1. Mode I (Opening mode) – Displacement is normal to crack surface. 2. Mode II (Sliding mode) – Displacement is in the plane of the plate. 3. Mode III (Tearing mode) – Out of plane shear.

Explain Griffith Theory. (or) State The Condition For Crack Growth?

Description : Explain Griffith Theory. (or) State The Condition For Crack Growth?

Last Answer : A crack can propagate if the energy release rate of crack is greater than crack resistance.

Define Stress Concentration And Stress Concentration Factor?

Description : Define Stress Concentration And Stress Concentration Factor?

Last Answer : Stress concentration is the increase in local stresses at points of rapid change in cross section or discontinuities. Stress concentration factor is the ratio of maximum stress at critical section to the nominal stress.

Distinguish Between Brittle Fracture And Ductile Fracture?

Description : Distinguish Between Brittle Fracture And Ductile Fracture?

Last Answer : In brittle fracture, crack growth is up to a small depth of the material. In ductile fracture large amount of plastic deformation is present to a higher depth.

What Are The Types Of Fracture?

Description : What Are The Types Of Fracture?

Last Answer : The two types of fracture are 1. Ductile fracture 2. Brittle fracture

Differentiate Between Repeated Stress And Reversed Stress?

Description : Differentiate Between Repeated Stress And Reversed Stress?

Last Answer : Repeated stress refers to a stress varying from zero to a maximum value of same nature. Reversed stress of cyclic stress varies from one value of tension to the same value of compression.

What Are The Types Of Variable Stresses?

Description : What Are The Types Of Variable Stresses?

Last Answer : Types of variable stresses are: 1. Completely reversed or cyclic stresses 2. Fluctuating stresses 3. Repeated stresses

What Are The Different Types Of Loads That Can Act On Machine Components?

Description : What Are The Different Types Of Loads That Can Act On Machine Components?

Last Answer : Different loads on machine components are: 1. Steady load. 2. Variable load. 3. Shock load 4. Impact load.

What Are The Various Phases Of Design Process?

Description : What Are The Various Phases Of Design Process?

Last Answer : The various phases of design process are: 1. Recognition of need. 2. Definition of problem 3. Synthesis 4. Analysis and optimization 5. Evaluation 6. Presentation

What Is Impact Load?

Description : What Is Impact Load?

Last Answer : If the time of load application is less than one third of the lowest natural period of vibration of the part, it is called an impact load.

Define Factor Of Safety?

Description : Define Factor Of Safety?

Last Answer : The ratio between maximum stresses to working stress is known as factor of safety. Factor of safety = Maximum stress /Working stress

Define Fatigue?

Description : Define Fatigue?

Last Answer : When a material is subjected to repeated stress, it fails at stresses below the yield point stress; such type of failure of the material is called fatigue.

Define Ductility?

Description : Define Ductility?

Last Answer : It is the property of the material enabling it to be drawn into wire, with the application of tensile force. It must be both strong and plastic. It is usually measured in terms of percentage elongation and reduction in area, (e.g.) Ni, Al, and Cu.

I am an athlete and do plenty of strength training but am looking for a way to increase my speed and endurance when it comes to running. Any advice?

Description : I am an athlete and do plenty of strength training but am looking for a way to increase my speed and endurance when it comes to running. Any advice?

Last Answer : yeah I play football and what u should really work on your explosion get a runnig parachute and maybe a weighted vest and literally in no time your endurance stamina and every thing will have greatly improved