If Sb, is the average bond stress on a bar of diameter subjected to maximum stress , the length of the embedment is given by (A) l = dt/Sb (B) l = dt/2Sb (C) l = dt/3Sb (D) l = dt/4S

If Sb, is the average bond stress on a bar of diameter subjected to maximum stress , the
length of the embedment is given by
(A) l = dt/Sb
(B) l = dt/2Sb
(C) l = dt/3Sb
(D) l = dt/4S
by

1 Answer

Answer :

Answer: Option D Answer: Option D
by

Related questions

If the average bending stress is 6 kg/cm2 for M 150 grade concrete, the length of embedment of a bar of diameter d according to I.S. 456 specifications, is (A) 28 d (B) 38 d (C) 48 d (D) 58 d

Description : If the average bending stress is 6 kg/cm2 for M 150 grade concrete, the length of embedment of a bar of diameter d according to I.S. 456 specifications, is (A) 28 d (B) 38 d (C) 48 d (D) 58 d

Last Answer : Answer: Option D

The length of lap in tension reinforcement should not be less than the bar diameter × (actual tension / four times the permissible average bond stress) if it is more than (A) 18 bar diameters (B) 24 bar diameters (C) 30 bar diameters (D) 36 bar diameters

Description : The length of lap in tension reinforcement should not be less than the bar diameter × (actual tension / four times the permissible average bond stress) if it is more than (A) 18 bar diameters (B) 24 bar diameters (C) 30 bar diameters (D) 36 bar diameters

Last Answer : Answer: Option C

If d is the diameter of a bar, ft is allowable tensile stress and fb, is allowable bond stress, the bond length is given by (A) ft .d/4fb (B) ( /4). (ft .d/fb) (C) ft .d²/fb (D) ( /4). (ft .d 3 /fb)

Description : If d is the diameter of a bar, ft is allowable tensile stress and fb, is allowable bond stress, the bond length is given by (A) ft .d/4fb (B) ( /4). (ft .d/fb) (C) ft .d²/fb (D) ( /4). (ft .d 3 /fb)

Last Answer : Answer: Option A

The length of the lap in a compression member is kept greater than bar diameter x (Permissible stress in bar / Five times the bond stress) or (A) 12 bar diameters (B) 18 bar diameters (C) 24 bar diameters (D) 30 bar diameters

Description : The length of the lap in a compression member is kept greater than bar diameter x (Permissible stress in bar / Five times the bond stress) or (A) 12 bar diameters (B) 18 bar diameters (C) 24 bar diameters (D) 30 bar diameters

Last Answer : Answer: Option C

In a bar of large length when held vertically and subjected to a load at its lower end, its own￾weight produces additional stress. The maximum stress will be (A) At the lower cross-section (B) At the built-in upper cross-section (C) At the central cross-section (D) At every point of the bar

Description : In a bar of large length when held vertically and subjected to a load at its lower end, its own￾weight produces additional stress. The maximum stress will be (A) At the lower cross-section (B) At the built-in upper cross-section (C) At the central cross-section (D) At every point of the bar

Last Answer : (B) At the built-in upper cross-section

If a solid shaft (diameter 20 cm, length 400 cm, N = 0.8 × 105 N/mm2 ) when subjected to a twisting moment, produces maximum shear stress of 50 N/mm2 , the angle of twist in radians, is (A) 0.001 (B) 0.002 (C) 0.0025 (D) 0.003

Description : If a solid shaft (diameter 20 cm, length 400 cm, N = 0.8 × 105  N/mm2 ) when subjected to a twisting  moment, produces maximum shear stress of 50 N/mm2 , the angle of twist in radians, is  (A) 0.001  (B) 0.002  (C) 0.0025  (D) 0.003 

Last Answer : (C) 0.0025 

The maximum load to which a fillet joint of length can be subjected to, is (A) 0.7 × S × fillet size × L (B) 2 × S × fillet size × L (C) Permissible shear stress × fillet size × L (D) (S × fillet size × L)/3

Description : The maximum load to which a fillet joint of length can be subjected to, is  (A) 0.7 × S × fillet size × L (B) 2 × S × fillet size × L (C) Permissible shear stress × fillet size × L (D) (S × fillet size × L)/3 

Last Answer : (A) 0.7 × S × fillet size × L

In a beam the local bond stress Sb, is equal to (A) Shear force/(Leaver arm × Total perimeter of reinforcement) (B) Total perimeter of reinforcement/(Leaver arm × Shear force) (C) Leaver arm/(Shear force × Total perimeter of reinforcement) (D) Leaver arm/(Bending moment × Total perimeter of reinforcement)

Description : In a beam the local bond stress Sb, is equal to (A) Shear force/(Leaver arm Total perimeter of reinforcement) (B) Total perimeter of reinforcement/(Leaver arm Shear force) (C) ... force Total perimeter of reinforcement) (D) Leaver arm/(Bending moment Total perimeter of reinforcement)

Last Answer : Answer: Option A

If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque when t attains maximum shear stress fs the ratio of inner diameter to outer diameter, is 17/64 (fs/N) (A) 1/2 (B) 1/3 (C) 1/4 (D) 1/5

Description : If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque  when t attains maximum shear stress fs  the ratio of inner diameter to outer diameter, is 17/64  (fs/N)  (A) 1/2  (B) 1/3  (C) 1/4  (D) 1/5

Last Answer : (C) 1/4 

A solid circular shaft of diameter d is subjected to a torque T. The maximum normal stress induced in the shaft, is (A) Zero (B) 16T/ 3 (C) 32T/ 3 (D) None of these

Description : A solid circular shaft of diameter d is subjected to a torque T. The maximum normal stress induced  in the shaft, is  (A) Zero  (B) 16T/ 3 (C) 32T/ 3 (D) None of these

Last Answer : (B) 16T/ 3

If tensile stress of a steel rod of diameter is 1400 kg/cm2 and bond stress is 6 kg/cm2 , the required bond length of the rod is (A) 30 D (B) 39 D (C) 50 D (D) 59 D

Description : If tensile stress of a steel rod of diameter is 1400 kg/cm2 and bond stress is 6 kg/cm2 , the required bond length of the rod is (A) 30 D (B) 39 D (C) 50 D (D) 59 D

Last Answer : (D) 59 D

A beam of length L is pinned at both ends and is subjected to a concentrated bending couple of moment M at its centre. The maximum bending moment in the beam is (A) M (B) M/2 (C) M/3 (D) ML/2

Description : A beam of length L is pinned at both ends and is subjected to a concentrated bending couple of  moment M at its centre. The maximum bending moment in the beam is  (A) M (B) M/2  (C) M/3  (D) ML/2 

Last Answer : (A) M

A triangular section having base b, height h, is placed with its base horizontal. If the shear stress at a depth y from top is q, the maximum shear stress is (A) 3S/bh (B) 4S/bh (C) 4b/Sh (D) 3b/bS

Description : A triangular section having base b, height h, is placed with its base horizontal. If the shear stress at a depth y from top is q, the maximum shear stress is (A) 3S/bh (B) 4S/bh (C) 4b/Sh (D) 3b/bS

Last Answer : (A) 3S/bh

A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending strain energy stored in the bar, is (A) 411 N mm (B) 511 N mm (C) 611 N mm (D) 711 N mm

Description : A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a  load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending  strain energy stored in the ... (A) 411 N mm  (B) 511 N mm  (C) 611 N mm  (D) 711 N mm 

Last Answer : (C) 611 N mm 

A bar L metre long and having its area of cross-section A, is subjected to a gradually applied tensile load W. The strain energy stored in the bar is (A) WL/2AE (B) WL/AE (C) W²L/AE (D) W²L/2AE

Description : A bar L metre long and having its area of cross-section A, is subjected to a gradually applied tensile  load W. The strain energy stored in the bar is  (A) WL/2AE (B) WL/AE (C) W²L/AE (D) W²L/2AE

Last Answer : (D) W²L/2AE

A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 Mpa. It is further subjected to a torque of 10 kNm. The maximum principal stress experienced on the shaft is closest to (a) 41Mpa (b) 82 Mpa (c) 164 Mpa (d) 204 Mpa

Description : A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 Mpa. It is further subjected to a torque of 10 kNm. The maximum principal stress experienced on the shaft is closest to (a) 41Mpa (b) 82 Mpa (c) 164 Mpa (d) 204 Mpa

Last Answer : (b) 82 Mpa

A solid shaft has diameter 80 mm. It is subjected to a torque of 4 KNm. The maximum shear stress induced in the shaft would be (a) 75/p N/mm2 (b) 250/p N/mm2 (c) 125/p N/mm2 (d) 150/p N/mm2

Description : A solid shaft has diameter 80 mm. It is subjected to a torque of 4 KNm. The maximum shear stress induced in the shaft would be (a) 75/p N/mm2 (b) 250/p N/mm2 (c) 125/p N/mm2 (d) 150/p N/mm2

Last Answer : (c) 125/p N/mm2

Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm

Description : Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm

Last Answer : c. 587.1 mm

What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2

Description : What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2

Last Answer : b. 14.69 N/mm2

What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2

Description : What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2

Last Answer : c. 50.57 N/mm2

A circular pipe is subjected to maximum shear force of 60 kN. What is the diameter of the pipe if maximum allowable shear stress is 5 Mpa? a. 27.311 mm b. 75.56 mm c. 142.72 mm d. 692.10 mm

Description : A circular pipe is subjected to maximum shear force of 60 kN. What is the diameter of the pipe if maximum allowable shear stress is 5 Mpa? a. 27.311 mm b. 75.56 mm c. 142.72 mm d. 692.10 mm

Last Answer : c. 142.72 mm

If a steel rod of 20 mm diameter and 5 metres long elongates by 2.275 mm when subjected to an axial pull of 3000 kg, the stress developed, is (A) 9.5541 kg/cm2 (B) 95.541 kg/cm2 (C) 955.41 kg/cm2 (D) 9554.1 kg/cm

Description : If a steel rod of 20 mm diameter and 5 metres long elongates by 2.275 mm when subjected to an  axial pull of 3000 kg, the stress developed, is  (A) 9.5541 kg/cm2 (B) 95.541 kg/cm2 (C) 955.41 kg/cm2 (D) 9554.1 kg/cm

Last Answer : (C) 955.41 kg/cm2

If a steel rod of 20 mm diameter and 5 metres long elongates by 2.275 mm when subjected to an axial pull of 3000 kg, the stress developed, is (A) 9.5541 kg/cm2 (B) 95.541 kg/cm2 (C) 955.41 kg/cm2 (D) 9554.1 kg/cm

Description : If a steel rod of 20 mm diameter and 5 metres long elongates by 2.275 mm when subjected to an  axial pull of 3000 kg, the stress developed, is  (A) 9.5541 kg/cm2 (B) 95.541 kg/cm2 (C) 955.41 kg/cm2 (D) 9554.1 kg/cm

Last Answer : (C) 955.41 kg/cm2

A simply supported uniform rectangular bar breadth b, depth d and length L carries an isolated load W at its mid-span. The same bar experiences an extension e under same tensile load. The ratio of the maximum deflection to the elongation, is (A) L/d (B) L/2d (C) (L/2d)² (D) (L/3d)²

Description : A simply supported uniform rectangular bar breadth b, depth d and length L carries an isolated  load W at its mid-span. The same bar experiences an extension e under same tensile load. The  ratio of the maximum deflection to the ... (A) L/d (B) L/2d (C) (L/2d)² (D) (L/3d)²

Last Answer : (C) (L/2d)

A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2 MN/mm2 and Eb = 0.1 MN/mm2 , the stresses developed are: (A) b = 10 N/mm2s = 20 N/mm2(B) b = 8 N/mm2s = 16 N/mm2(C) b = 6 N/mm2s = 12 N/mm2(D) b = 5 N/mm2s = 10 N/mm

Description : A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that  of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2  MN/mm2  and Eb = 0.1 ... 6 N/mm2 s  = 12 N/mm2 (D) b = 5 N/mm2 s  = 10 N/mm

Last Answer : (A) b = 10 N/mm2 s  = 20 N/mm

To pump water from a water reservoir 3 m deep and maximum water level at 135 m, a pump is installed to lift water up to R.L. 175 m at a constant rate of 36,00,000 litres per hour. If the length of the pipe is 1506 m and f = 0.01, ignoring other minor losses and assuming the economical diameter from Lea's formula D = 1.2 Q, the water horse power of the pump is (A) 400 (B) 450 (C) 500(D) 600

Description : To pump water from a water reservoir 3 m deep and maximum water level at 135 m, a pump is  installed to lift water up to R.L. 175 m at a constant rate of 36,00,000 litres per hour. If the length  of the ... the water horse power of the pump is  (A) 400  (B) 450  (C) 500 (D) 600

Last Answer : (D) 600

If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span of a square flat slab, should not be less than (A) WL/12 (L - 2D/3)² (B) WL/10 (L + 2D/3)² (C) WL/10 (L - 2D/3)² (D) WL/12 (L - D/3)²

Description : If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span ... (L + 2D/3)² (C) WL/10 (L - 2D/3)² (D) WL/12 (L - D/3)²

Last Answer : Answer: Option C

The ratio of the length and diameter of a simply supported uniform circular beam which experiences maximum bending stress equal to tensile stress due to same load at its mid span, is (A) 1/8 (B) 1/4 (C) 1/2 (D) 1/3

Description : The ratio of the length and diameter of a simply supported uniform circular beam which  experiences maximum bending stress equal to tensile stress due to same load at its mid span, is  (A) 1/8  (B) 1/4  (C) 1/2  (D) 1/3 

Last Answer : (C) 1/2 

In a cantilever subjected to a concentrated load (W) at the free end and having length =l, Maximum bending moment is (a) Wl at the free end (b) Wl at the fixed end (c) Wl/2 at the fixed end (d) Wl at the free end

Description : In a cantilever subjected to a concentrated load (W) at the free end and having length =l, Maximum bending moment is (a) Wl at the free end (b) Wl at the fixed end (c) Wl/2 at the fixed end (d) Wl at the free end

Last Answer : (b) Wl at the fixed end

In a simply supported beam subjected to uniformly distributed load (w) over the entire length (l), total load=W, maximum Bending moment is (a) Wl/8 or wl2/8 at the mid-point (b) Wl/8 or wl2/8 at the end (c) Wl/4 or wl2/4 (d) Wl/2

Description : In a simply supported beam subjected to uniformly distributed load (w) over the entire length (l), total load=W, maximum Bending moment is (a) Wl/8 or wl2/8 at the mid-point (b) Wl/8 or wl2/8 at the end (c) Wl/4 or wl2/4 (d) Wl/2

Last Answer : (a) Wl/8 or wl2/8 at the mid-point

Shear deflection of a cantilever of length L, cross sectional area A and shear modulus G, subjected to w/m u.d.l., is (A) (3/4) (L²w/GA) (B) (3/2) (L²w/GA) (C) (2/3) (L3w/GA) (D) (3/2) (Lw/GA²)

Description : Shear deflection of a cantilever of length L, cross sectional area A and shear modulus G, subjected to w/m u.d.l., is (A) (3/4) (L²w/GA) (B) (3/2) (L²w/GA) (C) (2/3) (L3w/GA) (D) (3/2) (Lw/GA²)

Last Answer : (A) (3/4) (L²w/GA)

A circular shaft subjected to torsion undergoes a twist of 10in a length of 120 cm. If the maximum shear stress induced is limited to 1000 kg/cm2and if modulus of rigidity G = 0.8 x 106then the radius of the shaft should be (a) p/8 (b) p/27 (c) 18/p (d) 27/p

Description : A circular shaft subjected to torsion undergoes a twist of 10in a length of 120 cm. If the maximum shear stress induced is limited to 1000 kg/cm2and if modulus of rigidity G = 0.8 x 106then the radius of the shaft should be (a) p/8 (b) p/27 (c) 18/p (d) 27/p

Last Answer : (d) 27/p

A compound pipe of diameter d1, d2 and d3 having lengths l1, l2 and l3 is to be replaced by an equivalent pipe of uniform diameter d and of the same length (l) as that of the compound pipe. The size of the equivalent pipe is given by (A) l/d² = + + (B) l/d³ = + ) + (C) = + + (D)

Description : A compound pipe of diameter d1, d2 and d3 having lengths l1, l2 and l3 is to be replaced by an equivalent pipe of uniform diameter d and of the same length (l) as that of the compound pipe. The size of the equivalent pipe is given by (A) l/d² = + + (B) l/d³ = + ) + (C) = + + (D)

Last Answer : Answer: Option D

The maximum longitudinal pitch in bolted joints, subjected to tensile forces, wherein t = thickness of the plate and D = diameter of bolt, is (a) 32 D (b) 16 D (c) 32 t (d) 16 t

Description : The maximum longitudinal pitch in bolted joints, subjected to tensile forces, wherein t = thickness of the plate and D = diameter of bolt, is (a) 32 D (b) 16 D (c) 32 t (d) 16 t

Last Answer : (d) 16 t

If the bond stress developed in a reinforced concrete beam is more than permissible value, it can be brought down by. (a) Increasing the depth of beam (b) Increasing the number of bars. (c) Decreasing the diameter of the bars (d) All of these

Description : If the bond stress developed in a reinforced concrete beam is more than permissible value, it can be brought down by. (a) Increasing the depth of beam (b) Increasing the number of bars. (c) Decreasing the diameter of the bars (d) All of these

Last Answer : (d) All of these

If L is the effective span of a R.C.C. beam which is subjected to maximum shear qmax at the ends, the distance from either end over which stirrups for the shear, are provided, is (A) (L/2) (1 - 3/qmax) (B) (L/3) (1 - 5/qmax) (C) (L/2) (1 - 5/qmax) (D) (L/2) (1 - 2/qmax)

Description : If L is the effective span of a R.C.C. beam which is subjected to maximum shear qmax at the ends, the distance from either end over which stirrups for the shear, are provided, is (A) (L/2) (1 - 3/qmax) (B) (L/3) (1 - 5/qmax) (C) (L/2) (1 - 5/qmax) (D) (L/2) (1 - 2/qmax)

Last Answer : Answer: Option C

18.The total extension of a taper rod of length ‘L’ and end diameters ‘D1’ and ‘D2’, subjected to a load (P), is given of a. 4PL/ΠE. D1D2 b. 3PL/ΠE. D1D2 c. 2PL/ΠE. D1D2 d. PL/ΠE.D1D2 Where E=Young’s modulus of elasticity

Description : 18.The total extension of a taper rod of length ‘L’ and end diameters ‘D1’ and ‘D2’, subjected to a load (P), is given of a. 4PL/ΠE. D1D2 b. 3PL/ΠE. D1D2 c. 2PL/ΠE. D1D2 d. PL/ΠE.D1D2 Where E=Young’s modulus of elasticity

Last Answer : a. 4PL/ΠE. D1D2

What is the value of shear stress acting on a plane of circular bar which is subjected to axial tensile load of 100 kN? (Diamet a. 58.73 Mpa b. 40.23 Mpa c. 39.60 Mpa d. Insufficient data

Description : What is the value of shear stress acting on a plane of circular bar which is subjected to axial tensile load of 100 kN? (Diamet a. 58.73 Mpa b. 40.23 Mpa c. 39.60 Mpa d. Insufficient data

Last Answer : c. 39.60 Mpa

When a bar is subjected to increase in temperature and its deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) None of the above

Description : When a bar is subjected to increase in temperature and its deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) None of the above

Last Answer : (b) Compressive

When a bar is subjected to a change of temperature and its longitudinal deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) Temperature

Description : When a bar is subjected to a change of temperature and its longitudinal deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) Temperature

Last Answer : (d) Temperature

A shaft is subjected to bending moment M and a torque T simultaneously. The ratio of the maximum bending stress to maximum shear stress developed in the shaft, is (A) M/T (B) T/M (C) 2M/T (D) 2T/M

Description : A shaft is subjected to bending moment M and a torque T simultaneously. The ratio of the  maximum bending stress to maximum shear stress developed in the shaft, is  (A) M/T (B) T/M (C) 2M/T (D) 2T/M

Last Answer : (C) 2M/T

shaft subjected to a bending moment M and a torque T, experiences (A) Maximum bending stress = 32M d 3 (B) Maximum shear stress = 16 T d 3 (C) Both (a) and (b) (D) Neither (a) nor (b)

Description :  shaft subjected to a bending moment M and a torque T, experiences  (A) Maximum bending stress = 32M d 3 (B) Maximum shear stress = 16 T d 3 (C) Both (a) and (b)  (D) Neither (a) nor (b)

Last Answer : (C) Both (a) and (b) 

Along the principal plan subjected to maximum principal stress (A) Maximum shear stress acts (B) Minimum shear stress acts(C) No shear stress acts (D) None of these

Description : Along the principal plan subjected to maximum principal stress (A) Maximum shear stress acts (B) Minimum shear stress acts (C) No shear stress acts (D) None of these

Last Answer : (C) No shear stress acts

If a shaft is simultaneously subjected to a toque T and a bending moment M, the ratio of maximum bending stress and maximum shearing stress is (A) M/T (B) T/M (C) 2M/T (D) 2T/M

Description : If a shaft is simultaneously subjected to a toque T and a bending moment M, the ratio of maximum bending stress and maximum shearing stress is (A) M/T (B) T/M (C) 2M/T (D) 2T/M

Last Answer : (C) 2M/T

A rectangular beam 20 cm wide is subjected to a maximum shearing force of 10,000 kg, the corresponding maximum shearing stress being 30 kg/cm2 . The depth of the beam is (A) 15 cm (B) 20 cm (C) 25 cm (D) 30 cm

Description : A rectangular beam 20 cm wide is subjected to a maximum shearing force of 10,000 kg, the corresponding maximum shearing stress being 30 kg/cm2 . The depth of the beam is (A) 15 cm (B) 20 cm (C) 25 cm (D) 30 cm

Last Answer : (C) 25 cm

A cast iron T section beam is subjected to pure bending. For maximum compressive stress to be three times the maximum tensile stress, centre of gravity of the section from flange side is (A) h/4 (B) h/3 (C) h/2 (D) 2/3 h

Description : A cast iron T section beam is subjected to pure bending. For maximum compressive stress to be  three times the maximum tensile stress, centre of gravity of the section from flange side is  (A) h/4  (B) h/3  (C) h/2  (D) 2/3 h

Last Answer : (A) h/4 

Pick up the correct statement from the following: (A) Isotropic consolidation of clay can be obtained in the triaxial apparatus under equal all￾round pressure (B) If the present effective stress is the maximum to which the clay has ever been subjected, it is called normally consolidated clay (C) If the present effective stress in the past was more than present effective stress, it is called over-consolidated clay (D) All the above

Description : Pick up the correct statement from the following: (A) Isotropic consolidation of clay can be obtained in the triaxial apparatus under equal all￾round pressure (B) If the present effective stress is the ... more than present effective stress, it is called over-consolidated clay (D) All the above

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) An unconfined compression test is a special case of triaxial compression test (B) An unconfined compression test is a special case of direct shear test (C) The confining pressure is maximum during an unconfined compression test (D) The cylindrical specimen of a soil is subjected to major principal stress till it fails due to shearing along the plane of the failure

Description : Pick up the correct statement from the following: (A) An unconfined compression test is a special case of triaxial compression test (B) An unconfined compression test is a special case of direct ... subjected to major principal stress till it fails due to shearing along the plane of the failure

Last Answer : Option A

is the pre-stressed force applied to the tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The maximum stress in the beam, subjected to a maximum bending moment , is (A) f = (P/A) + (Z/M) (B) f = (A/P) + (M/Z) (C) f = (P/A) + (M/Z) (D) f = (P/A) + (M/6Z)

Description : is the pre-stressed force applied to the tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The maximum stress in the beam, subjected to a maximum bending moment , is (A) f = (P/A) + (Z/M) ... ) + (M/Z) (C) f = (P/A) + (M/Z) (D) f = (P/A) + (M/6Z)

Last Answer : Answer: Option C

is the pre-stressed force applied to tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The minimum stress on the beam subjected to a maximum bending moment is (A) f = (P/A) - (Z/M) (B) f = (A/P) - (M/Z) (C) f = (P/A) - (M/Z) (D) f = (P/A) - (M/6Z)

Description : is the pre-stressed force applied to tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The minimum stress on the beam subjected to a maximum bending moment is (A) f = (P/A) - (Z/M) (B) f = (A/P) - (M/Z) (C) f = (P/A) - (M/Z) (D) f = (P/A) - (M/6Z)

Last Answer : Answer: Option C