Description : Pin #6 of the ahead valve position sensor as shown in the illustration is connected _______________. EL-0099 A. to (-) 50 volts D.C. B. in parallel with PCOM C. to (+) 50 volts D.C. D. to analog common
Last Answer : Answer: C
Description : Pin #8 of the astern valve position sensor shown in the illustration is connected _______________. EL-0099 A. to analog common B. in series with PCOM C. to (-) 50 volts D.C. D. to (+) 50 volts D.C.
Last Answer : Answer: A
Description : The signal to the circuit on card 'A0AA2' at coordinate '29Q' shown in the illustration is on the ____________. EL-0099 A. non-inverting input at pin '20' B. inverting input at pin '16' C. non-inverting input at pin '14' D. inverting input at pin '46'
Last Answer : Answer: B
Description : As shown in the illustration, when the 'speed control' system is in 'SPLIT' _______________. EL-0096 A. Relays #1, #5 and #8 are not used B. the 'slew rated controller' is grounded through Relay ... E/P converters' are bypassed and air is fed directly to the governors via the 'load sharing valve'
Description : What is the value of the capacitor in the astern valve position circuit shown in the illustration? EL-0099 A. 100 kFarad B. 0.5 microfarad C. 0.5 millifarad D. 50 kFarad
Description : Peripheral components for the operation of the astern valve position amplifier circuit shown in the illustration are _____________. EL-0099 A. resistors B. operated on +28 volts D.C. C. located on a separate circuit card D. all of the above
Description : What do the arrow-like symbols at coordinate '33J' shown in the illustration represent? EL-0099 A. Connection to ground. B. Connection to the analog common bus. C. Plug-in connection. D. Screw connection on a terminal board.
Description : The sensor connected to 'signal conditioner' (6000F125) shown in the illustration is a/an ______________. EL-0094 A. thermocouple B. transducer C. inverter D. RTD
Description : The sensor connected to 'signal conditioner' (6000F085) shown in the illustration is a/an ______________. EL-0094 A. thermocouple B. transducer C. inverter D. RTD
Last Answer : Answer: D
Description : In the schematic diagram of the DC compound generator shown in the illustration, the positive ammeter reading is 500 amps and the negative ammeter reading is 475 amps. What is the current flow through the neutral bus? EL-0037 A. 0 amp B. 12.5 amp C. 25 amp D. 975 amp
Description : In the illustration, moving the engine room reference in the direction indicated will _________. SE-0002 A. cause a positive signal to be sent to the ahead function generator creating a more ... the ahead valve to open until the negative signal exceeds the low lube oil pressure override signal
Description : In the illustration, the function generators will accept only a signal of a given polarity, if negative is used for ahead and positive for astern, moving the bridge reference in the direction ... cause a speed change until the output voltage exceeds the value of the lube oil pressure override
Description : The 'pitch controller module' shown in the illustration is fed the actual pitch position of the propeller from the _____________. EL-0095 A. 'pitch meter' B. 'pitch feedback potentiometer' C. #5 relay position D. pitch error signal
Description : In order to decrease the resistance of the 50K pot located at '21Q/R' shown in the illustration, the wiper of the actual component must be moved ____________. EL-0099 A. to the left B. to the right C. clockwise D. counterclockwise
Description : The power requirements for operating the circuits shown in the illustration are ____________. EL-0099 A. (+) and (-) 50 volts D.C. B. (+) 28 and (+) 50 volts D.C. C. (+) 28 volts D.C. and 115 volts A.C. D. (+) 28 volts and (-) 50 volts D.C.
Description : What type of circuit is on card 'A0AA2' at coordinate '29Q' shown in the illustration? EL-0099 A. Operational amplifier B. Digital logic inverter C. Square wave pulse generator D. Binary counter
Description : What does the arrangement at coordinates '62E' shown in the illustration represent? EL-0099 A. Position recording drum and stylus B. Temperature compensating thyristor C. Miniature bridge rectifier D. Twisted wire pair within a shield
Description : What is the polarity of voltage at point 'Z' in the circuit shown in the illustration? EL-0085 A. It will always be positive. B. It will always be negative. C. It depends on the instantaneous polarity at point 'W'. D. It cannot be determined without a voltmeter.
Description : If power were lost to the winch shown in the illustration while in 'second point hoist' the winch would stop. When power is restored the winch would ______________. EL-0102 A. continue to run at ' ... switch' is returned to 'off' closing the 'reset' contacts and then moved to any 'run' position
Description : The only point in the steering stand shown in the illustration which needs periodic lubrication is the ______________. EL-0098 A. repeater assembly ball bearings B. steering wheel bearing C. operation selector switch D. course selector pointer
Description : When the motor shown in the illustration is running and the stop button is pushed, which of the following statements will hold true? EL-0010 A. Coil 'M' will now be energized. B. Coil 'CR' will now be energized. C. Contact 'M' will close as contact 'CR' opens. D. Contacts 'M' and 'CR' will open.
Description : As shown in the illustration, which of the operations listed will happen when the 'jog button' is pushed? EL-0010 A. Coil 'CR' closes the normally open 'CR' contacts. B. Coil 'M' opens contact 'M'. C. Coil 'M' closes contact 'M'. D. Contact 'M' remains open despite the jog button being pushed.
Description : As shown in the illustration, which listed action will occur first when push button 'Q' is depressed? EL-0017 A. Contacts 'H-1', 'H-2' and 'H-3' close. B. Contact 'H-4' closes. C. Operating coil 'C' energizes. D. Switch 'R' opens.
Description : As shown in the illustration, the same indication occurs when 'C' opens as when ____________. EL-0058 A. 'E2' burns out B. 'H2' opens C. 'G' opens D. 'F' burns out
Description : As shown in the illustration, what happens when 'A' is closed, 'B' is in position '2' and component 'E2' burns out? EL-0058 A. 'H' energizes and 'D' makes contact. B. 'F' goes out allowing 'G' to disconnect. C. 'G' sounds an alarm and 'F' illuminates. D. 'C' opens causing 'A' to also open.
Description : Which sensor shown in the illustration develops its own conditioning and point setting and 'reports' directly to the 'annunciator'? EL-0094 A. Transducer B. Resistance Temperature Detector (RTD) C. Pressure Switch D. Thermocouple
Description : What is the calculated voltage at the positive and negative terminals of the battery shown in the illustration if each cell has a voltage of 1.5 volts? EL-0034 A. 1.5 volts B. 3.0 volts C. 6.0 volts D. 12.0 volts
Description : Batteries 'A' and 'B' shown in the illustration are 6 volts each and batteries 'C' and 'D' are 24 volts each. If 'A' were connected in series-opposing to 'C' and 'B' was similarly ... the top terminal C. 30 volts, negative at the bottom terminal D. 30 volts, positive at the bottom terminal
Description : Batteries 'A' and 'B' shown in the illustration are 6 volts each and batteries 'C' and 'D' are 24 volts each. If 'A' and 'B' were reconnected to be in series-opposing to 'C' and 'D' ... at the top terminal C. 30 volts, negative at the bottom terminal D. 30 volts, positive at the bottom terminal
Description : Considering the function of the circuit shown in the illustration, what is the purpose of supplying the thrust lever potentiometers with both (+) and (-) 15 volts? EL-0095 A. To select which ... alternate voltage supply if the other fails. D. So as to automatically select the position of Relay #
Description : The wiring diagram for the motor starting circuit shown in the illustration indicates ______________. EL-0007 A. resistance starting B. reduced voltage starting C. low voltage protection D. low voltage release
Description : As shown in the illustration, the function of the switch labeled 'PFSW' is to determine the ______________. EL-0003 A. bus frequency B. reactive volt amperes of the bus C. frequency of either generator D. power factor of either generator
Description : As shown in the illustration, the motor generator(M-G) set's three-phase motor drives the ______________. EL-0101 A. motor and the generator B. motor and the exciter C. generator and the exciter D. main field and the interpole field
Description : The reading at 'K' on the megger scale shown in the illustration, is ______________. EL-0044 A. 400 ohms B. 4,000 ohms C. 40,000 ohms D. 400,000 ohms
Description : The advantage(s) of the method of D.C. motor speed control shown in the illustration is/are ______________. EL-0101 A. elimination of armature starting resistor losses B. elimination of speed instability with variable loads C. the ease of reversing motor direction D. all of the above
Description : The purpose of resistor bank 'R1-R5' in the winch circuit shown in the illustration is to ______________. EL-0102 A. limit armature current in lower and 'series field' current in hoist to ... required speeds D. regulate the strength of the brake solenoid 'B1-B2' in both directions of operation
Description : As shown in the illustration, operating the reversing switch will change the polarity of the ______________. EL-0101 A. generator field B. generator armature C. motor armature D. all of the above
Description : When 'selector switch' 'SEL8' shown in the illustration is in the 'ON' position, contacts '3,4' and '7,8' are respectively ______________. EL-0100 A. open; closed B. closed; open C. open; open D. closed; closed
Description : The 'reset' contacts of the master switch shown in the illustration are ______________. EL-0102 A. closed only when the master switch is 'off' B. closed only when the master switch selects a 'run' condition C. opened separately by the winch operator D. opened when line voltage drops 10%
Description : As shown in the illustration, the M-G set's three-phase motor drives the ______________. EL-0101 A. motor and the generator B. motor and the exciter C. generator and the exciter D. main field and the interpole field
Description : The voltage at the reference electrode of the circuit shown in the illustration is applied to the input of a/an ______________. EL-0090 A. class A detector whose output drives an ... drives an 2-stage isolation transformer D. magnetic amplifier whose output controls a saturable reactor
Description : The purpose of a 'slew rate controller' in a circuit such as shown in the illustration is to ______________. EL-0096 A. limit the rate of change of a signal B. introduce a 'live zero' ... linear input into a non-linear output D. reduce air pressure to a value required by a combination circuit
Description : The device in figure 'B' shown in the illustration can be used to control an AC load yet maintain its high gain by ______________. EL-0091 A. connecting the load to the output side of the ... connecting the load to the input side of the bridge D. reversing the current flow through the bias winding
Description : In actual applications, electrical connections to 'R1-R2' of figure 'A' and to 'R1-R2- R3' of figure 'B' shown in the illustration are made by ______________. EL-0092 A. soldered contacts B. spliced and taped connections C. slip rings and brushes D. solderless crimp-on connectors
Description : The horizontal line which cuts across 'L1' shown in figure 'A' of the illustration indicates a/an ______________. EL-0091 A. iron core B. saturable core C. air gap D. capacitive coupling
Description : If the 'E/P converter' shown in the illustration operated on a range of 1-9 volts and 6-30 PSI, a 5 volt input would yield ______________. EL-0096 A. 9 PSI B. 15 PSI C. 18 PSI D. 24 PSI
Description : Figure 'A' of the diagram shown in the illustration represents a ______________. EL-0092 A. differential transformer B. saturable reactor C. synchro system D. magnetic amplifier
Description : For console circuit card 'LLEA' as shown in the illustration at coordinates '63R/S', the input(s) and output(s) are respectively on pin numbers ____________. EL-0100 A. '5' and '3' & '4' B. '2' & '3' and '5' & '6' C. '5' & '6' and '2' & '3' D. '3' & '4' and '5'
Description : The sensor connected to 'signal conditioner' (6000AH170) shown in the illustration is a/an _____________. EL-0094 A. thermocouple B. transducer C. inverter D. RTD
Description : What is the purpose of each of the 'signal conditioners' (6000F085 / AH170 / F125) shown in the illustration? EL-0094 A. Convert the varying signal from its particular sensor and deliver a ... the 'setpoint module' in order to keep the pressure or temperature at its sensor at set limits.