Description : A 24 volt battery supplies three devices wired in parallel that each have a resistance of 9 ohms. What is the voltage drop across each device?
Last Answer : A simple circuit has three resistors connected in series. The resistors are 14 ohms 12 ohms and 9 ohms. What is the total resistance of the circuit?
Description : 9 leds each of 1 volt drop is series with 9 volt battery , do we need a resistor?(SMD leds) I have seen some smd leds without resistor !
Last Answer : We connect resistor to limit the current. So, it depends upon the current rating of the LED, which is provided by manufacturer.
Description : An LED is operated on a 12 volt automobile circuit. The voltage drop across the LED is 2 volts and the current must be limited to 50 milliamps to prevent its overheating and destruction. What size resistor must be used? w) 60 ohms x) 100 ohms y) 120 ohms z) 200 ohms
Last Answer : ANSWER: Z -- 200 OHMS
Description : A battery is connected to a circuit containing three resistors in parallel. The values of the three resistors are 2 ohms, 3 ohms, and 6 ohms. What is the voltage of the battery if the total circuit current is 12 amps? A. 2 volts B. 6 volts C. 12 volts D. 24 volt
Last Answer : Answer: C
Description : In the illustrated circuit the voltage is 12 VDC and the resistance is 3 ohms. If the battery is rated for 120 amp-hours, how long before the voltage will drop to 1.75 volts per cell? EL-0018 A. 12 hours B. 1.75 days C. 30 hours D. 2.5 days
Description : can a 12 volt battery be connected to the Bushnell sn 9421 22138
Last Answer : Need Answer
Description : In the adjoining circuit, the battery `E_(1)` has an e.m.f me of 12 volt and zero internal resistance while the battery E has an e.m.f me of 2volt . I
Last Answer : In the adjoining circuit, the battery `E_(1)` has an e.m.f me of 12 volt and zero internal resistance while the ... ohm is A. 250 B. 100 C. 50 D. 200
Description : A coil is wound with 400 feet of No. 16 tinned copper wire and connected to a 12 volt battery. What is the current if the resistance per 1000 feet of No. 16 tinned copper wire is 4.26 ohms? A. 4.8 amps B. 7.06 amps C. 10.65 amps D. 11.27 amps
Last Answer : Answer: B
Description : A coil is wound with 200 feet of No. 16 tinned copper wire and connected to a 12 volt battery. What is the current if the resistance per 1000 feet of No. 16 tinned copper wire is 4.26 ohms? A. 1.14 amps B. 7.04 amps C. 10.22 amps D. 14.08 amps
Last Answer : Answer: D
Description : If a 6 volt battery were connected in series with a 24 volt battery by putting their negative terminals together, what would be the result? A. 'Zero' volts B. 12 volts of the opposite polarity C. 18 volts, positive on the 24 volt battery D. 30 volts, negative on the 24 volt battery
Description : The number of cells in a 12 volt lead-acid battery is ________________. A. three cells B. four cells C. six cells D. twelve cells
Description : Battery operated sprayer consists of 10 lit capacity tank and rechargeable battery. b. 10 Volt c. 12 Volt. d. None of above Ans- a. 6 Volt
Last Answer : Ans- a. 6 Volt
Description : What is the voltage drop across the resistor in an RC charging circuit when the charge on the capacitor is equal to the battery voltage?
Last Answer : Zero.
Description : Can you recharge a mostly dead 9 volt battery by plugging a fresh one into the terminals?
Last Answer : you’ll end up ruining both and possibly start a fire.
Description : Where can it be ordered?
Last Answer : You do not state the capacity (Ah), but if 1.3Ah is enough - it could be this: Bosch 14.4 V 1.3 AH LI-ION X ? >> see here: https://baterie-k-aku-naradi.heureka.cz/bosch-14_4-v-1_3-ah-li-ion-x/#
Description : A potentiometer wire of length 10 m and resistance `10 Omega` per meter is connected in serice with a resistance box and a 2 volt battery. If a potent
Last Answer : A potentiometer wire of length 10 m and resistance `10 Omega` per meter is connected in serice with a ... Omega` C. `190 Omega` D. `90 Omega`
Description : The length of a wire of a potentiometer is 100 cm, and the e.m.f. of its standard cell is E volt. It is employed to measure the e.m.f. of a battery wh
Last Answer : The length of a wire of a potentiometer is 100 cm, and the e.m.f. of its standard cell is E ... current in the potentiometer wire D. `(30E)/(100)`
Description : What battery is recommended with a 3 volt DC motor?
Last Answer : Need answer
Description : How many amps is 9 volt battery?
Description : What happens to the current in a circuit if a 1.5-volt battery is removed and is replaced by a 3-volt battery?
Last Answer : The battery cannot be removed quickly! Inductance of the wiring stores energy and keeps the current flowing and decaying smoothly. There will be an opposite polarity, higher voltage pulse on the battery terminals, limited by the circuit capacitance only.
Description : A twelve volt lead-acid battery is constructed of _________. A. one cell B. three cells C. six cells D. twelve cells
Description : Battery capacities are given in _____________. A. volts B. volt-amperes C. volt-hours D. ampere-hours
Description : What is the total resistance of the electrical circuit illustrated if the resistance of R1 is 2 ohms, R2 is 4 ohms, and R3 is 4 ohms with a 6 volt battery? EL-0021 A. 0.01 ohms B. 0.10 ohms C. 1.00 ohms D. 10.00 ohms
Description : What is the current through R2 of the circuit illustrated if the resistances of R1 is 2 ohms, R2 is 4 ohms, and R3 is 4 ohms with a 6 volt battery? EL-0021 A. 0.5 amp B. 1.5 amps C. 3.0 amps D. 6 amps
Description : What is the total current in the illustrated circuit with a 6 volt battery if the resistance of R1 is 2 ohms, R2 is 4 ohms, and R3 is 4 ohms? EL-0021 A. 0.6 amp B. 1 amp C. 4 amps D. 6 amps
Description : The capacity of a battery is expressed in terms of A ampere per hour B current C volt D ampere
Last Answer : A ampere per hour
Description : A 10 volt battery connected to a capacitor delivers a charge of 0.5 coulombs. The capacitance of the capacitor is: w) 2 x 10-2 farads x) 5 x 10-2 farads y) 2 farads z) 5 farads
Last Answer : ANSWER: X -- 5 x 10-2 FARADS
Last Answer : Voltage drop is not caused by this , poor connection and bad conducters and danger parts , They are causes by voltage loss
Description : When 7/0.029 V.I.R cable is carrying 20 A, a drop of 1 V occurs every 12 m. The voltage drop in a 100 m run of this cable when it is carrying 10 A is nearly (a) 4.2 V (b) 3.2 V (c) 1.2 V (d) 0.42 V
Last Answer : When 7/0.029 V.I.R cable is carrying 20 A, a drop of 1 V occurs every 12 m. The voltage drop in a 100 m run of this cable when it is carrying 10 A is nearly 1.2 V
Description : If voltage across a bulb rated 220 volt-100 watt drops by `2.5 %` of its value, the percentage of the rated value by which the power would decrease is
Last Answer : If voltage across a bulb rated 220 volt-100 watt drops by `2.5 %` of its value, the percentage of the rated value ... 20%` B. `2.5%` C. `5%` D. `10%`
Description : IF YOU HAVE A 277 volt circuit IN you go from PHASE 1 to ground what will your voltage be?
Description : The threshold frequency is the frequency below which - (1) photo current is constant (2) photo current increases with voltage (3) photo current decreases with volt (4) photo electric emission is not possible
Last Answer : (4) photo electric emission is not possible
Description : What will be the total output voltage if four 1.5 volt batteries are connected in a series-parallel arrangement as shown in the illustration? EL-0039 A. 1.5 volts B. 3.0 volts C. 4.5 volts D. 6.0 volts
Description : A common-emitter circuit has an input voltage of 0.1 volt, an output voltage of 2.0 volts, an input current of 0.5 milliamps, and an output current of 10 milliamps. What is the power gain? A. 20 B. 40 C. 400 D. 4000
Description : Two 100 watt light bulbs are connected in parallel across a 100 volt power supply. The total power developed in the circuit is _______________. A. 200 watts B. 100 watts C. 50 watts D. equal to the product of the amperes times the voltage in each branch
Last Answer : Answer: A
Description : In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal ... 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC
Description : In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC
Description : In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC
Description : A volt-ohm-millimeter can be used to check for ____________. A. continuity B. grounds C. voltage D. all of the above
Description : A device which can be used to check the calibration of a circuit breaker is a _________________. A. 500 volt megohmmeter B. portable low voltage high current testing unit C. standard digital multimeter D. clamp-on voltmeter
Description : The standard method of controlling the output voltage of a 440 volt, 60 Hz, AC generator is accomplished by adjusting the ____________. A. prime mover speed droop B. number of poles C. alternator field excitation D. load on the alternator
Description : The output voltage of a 440 volt, 60 Hz AC generator is controlled by the ______________. A. load on the alternator B. load on the prime mover C. speed of the prime mover D. exciter output voltage
Description : When the circuit shown in the illustration is operating correctly, the voltage at the reference electrode will be kept in the optimum range of ____________. EL-0090 A. 0.01 - 0.05 volt B. 0.80 - 0.85 volt C. 35 - 60 volts D. 100 - 115 volts
Description : Figure 'D' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts
Description : Figure 'C' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts
Description : Figure 'B' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts
Description : Figure 'A' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts
Description : To properly use a hook-on-type volt/ammeter to check current flow, you must FIRST _____________. A. de-energize the circuit to allow connection of the instrument in series B. hook the jaws ... test leads to the appropriate terminals D. short the test leads and calibrate the instrument to zero
Description : The output voltage of a 440 volt, 60 hertz, AC generator is controlled by the _____________. A. prime mover speed B. exciter output voltage C. load on the alternator D. number of poles