Which of the following steel sections should preferably be used at places where torsion occurs? (a) Box-type section (b) Channel section (c) Angle section (d) Any of the above

Which of the following steel sections should preferably be used at places where torsion occurs?
(a) Box-type section (b) Channel section
(c) Angle section (d) Any of the above
by

1 Answer

Answer :

(a) Box-type section
by

Related questions

Pick up the correct statement from the following: (A) In a loaded beam, the moment at which the first yield occurs is called yield moment(B) In a loaded beam, the moment at which the entire section of the beam becomes fully plastic, is called plastic moment (C) In a fully plastic stage of the beam, the neutral axis divides the section in two sections of equal area (D) All the above

Description : Pick up the correct statement from the following:  (A) In a loaded beam, the moment at which the first yield occurs is called yield moment (B) In a loaded beam, the moment at which the ... beam, the neutral axis divides the section in two sections of  equal area  (D) All the above 

Last Answer : (D) All the above 

Which of the following is not an assumption in derivation of torsion equation? a. Circular shaft remains circular after twisting b. Plane section of the shaft remain plane after twisting c. Material of shaft is isotropic d. Angle of twist is proportional to radius

Description : Which of the following is not an assumption in derivation of torsion equation? a. Circular shaft remains circular after twisting b. Plane section of the shaft remain plane after twisting c. Material of shaft is isotropic d. Angle of twist is proportional to radius

Last Answer : d. Angle of twist is proportional to radius

The application of elastic theory to the beams is based on the assumption that (a) At any cross-section, plane sections before bending remain plane after bending (b) All tensile stresses are taken up by reinforcement alone and none by the concrete. (c) Steel reinforcement is free from initial stresses when it is embedded in concrete. (d) All of the above

Description : The application of elastic theory to the beams is based on the assumption that (a) At any cross-section, plane sections before bending remain plane after bending (b) All tensile stresses are taken ... reinforcement is free from initial stresses when it is embedded in concrete. (d) All of the above

Last Answer : (d) All of the above

The following assumption is not true in the theory of pure torsion: (A) The twist along the shaft is uniform (B) The shaft is of uniform circular section throughout (C) Cross-section of the shaft, which is plane before twist remains plane after twist (D) All radii get twisted due to torsion

Description : The following assumption is not true in the theory of pure torsion:  (A) The twist along the shaft is uniform  (B) The shaft is of uniform circular section throughout  (C) Cross- ... , which is plane before twist remains plane after twist  (D) All radii get twisted due to torsion 

Last Answer : (D) All radii get twisted due to torsion 

The torsion resisting capacity of a given reinforced concrete section. (a) Decreases with decrease in stirrups spacing. (b) Decreases with increase in longitudinal bars. (c) Does not depend upon stirrups and longitudinal steels. (d) Increases with increase in stirrups and longitudinal steels.

Description : The torsion resisting capacity of a given reinforced concrete section. (a) Decreases with decrease in stirrups spacing. (b) Decreases with increase in longitudinal bars. (c) Does not depend upon stirrups and longitudinal steels. (d) Increases with increase in stirrups and longitudinal steels.

Last Answer : (d) Increases with increase in stirrups and longitudinal steels.

The flow in a pipe or channel is said to be non-uniform when (A) The liquid particles at all sections have the same velocities (B) The liquid particles at different sections have different velocities (C) The quantity of liquid flowing per second is constant (D) Each liquid particle has a definite path

Description : The flow in a pipe or channel is said to be non-uniform when (A) The liquid particles at all sections have the same velocities (B) The liquid particles at different sections have different ... The quantity of liquid flowing per second is constant (D) Each liquid particle has a definite path

Last Answer : Answer: Option B

The flow in a pipe or channel is said to be uniform when (A) The liquid particles at all sections have the same velocities (B) The liquid particles at different sections have different velocities (C) The quantity of liquid flowing per second is constant (D) Each liquid particle has a definite path

Description : The flow in a pipe or channel is said to be uniform when (A) The liquid particles at all sections have the same velocities (B) The liquid particles at different sections have different ... The quantity of liquid flowing per second is constant (D) Each liquid particle has a definite path

Last Answer : Answer: Option A

Cockroaches live preferably in D A. Cold places B. Warm places C. Dark places D. Warm and dark places

Description : Cockroaches live preferably in D A. Cold places B. Warm places C. Dark places D. Warm and dark places

Last Answer : Warm and dark places

Pick up the correct statement from the following: (A) For channels, the shear centre does not coincide its centroid (B) The point of intersection of the bending axis with the cross section of the beam, is called shear centre (C) For I sections, the shear centre coincides with the centroid of the cross section of the beam (D) All the above

Description : Pick up the correct statement from the following:  (A) For channels, the shear centre does not coincide its centroid  (B) The point of intersection of the bending axis with the cross section ... shear centre coincides with the centroid of the cross section of the beam  (D) All the above

Last Answer : (D) All the above

If h1 and h2 are the differences in level between ground and the formation levels, m is the slope of the sloping sides. D is the distance between the cross sections then, Prismoidal correction for a level section is (A) D/2m(h1 - h2) (B) D/3m(h1 - h2) (C) D/6m(h1 - h2)2(D) D/6m(h1 - h2)3

Description : If h1 and h2 are the differences in level between ground and the formation levels, m is the slope of the sloping sides. D is the distance between the cross sections then, Prismoidal correction for a level section is (A) D/2m(h1 - h2) (B) D/3m(h1 - h2) (C) D/6m(h1 - h2)2 (D) D/6m(h1 - h2)3

Last Answer : (C) D/6m(h1 - h2)2

In the cross-section method of indirect contouring, the spacing of cross-sections depends upon (i) Contour interval (ii) Scale of plan (iii) Characteristics of ground The correct answer is (A) Only (i) (B) (i) and (ii) (C) (ii) and (iii) (D) (i), (ii) and (iii)

Description : In the cross-section method of indirect contouring, the spacing of cross-sections depends upon (i) Contour interval (ii) Scale of plan (iii) Characteristics of ground The correct answer is (A) Only (i) (B) (i) and (ii) (C) (ii) and (iii) (D) (i), (ii) and (iii)

Last Answer : (D) (i), (ii) and (iii)

determining stresses in frames by methods of sections, the frame is divided into two parts by an imaginary section drawn in such a way as not to cut more than (A) Two members with unknown forces of the frame (B) Three members with unknown forces of the frame (C) Four members with unknown forces of the frame (D) Three members with known forces of the frame

Description : determining stresses in frames by methods of sections, the frame is divided into two parts by an imaginary section drawn in such a way as not to cut more than (A) Two members with unknown forces ... C) Four members with unknown forces of the frame (D) Three members with known forces of the frame

Last Answer : (B) Three members with unknown forces of the frame

Pick up the correct statement regarding the centre line method of estimating a building (A) Product of the centre line of the walls and area of cross-section of any item, gives total quantity of the item (B) The centre line is worked out separately for different sections of walls of a building (C) The centre line length is reduced by half the layer of main wall joining the partition wall (D) All the above

Description : Pick up the correct statement regarding the centre line method of estimating a building (A) Product of the centre line of the walls and area of cross-section of any item, gives total quantity of the ... length is reduced by half the layer of main wall joining the partition wall (D) All the above

Last Answer : (D) All the above

In the mid-section formula (A) The mean depth is the average of depths of two consecutive sections (B) The area of mid-sections is calculated by using mean depth (C) The volume of the earth work is calculated by multiplying the mid-section area by the distance between the two original sections (D) All of the above

Description : In the mid-section formula (A) The mean depth is the average of depths of two consecutive sections (B) The area of mid-sections is calculated by using mean depth (C) The volume of the ... multiplying the mid-section area by the distance between the two original sections (D) All of the above

Last Answer : (D) All of the above

The thickness of a laminar boundary layer over a flat plate at two different sections P and Q are 0.8 cm and 2.4 cm respectively. If the section Q is 3.6 m downstream of P, the distance of section P from the leading edge of the plate is (a) 0.32 m (b) 0.22 m (c) 0.40 m (d) 0.53 m

Description : The thickness of a laminar boundary layer over a flat plate at two different sections P and Q are 0.8 cm and 2.4 cm respectively. If the section Q is 3.6 m downstream of P, the distance of section P from the leading edge of the plate is (a) 0.32 m (b) 0.22 m (c) 0.40 m (d) 0.53 m

Last Answer : Ans: (c) Correct Answer is: 0.45 m

A doubly reinforced section is used (a) When the members are subjected to alternate external loads and the bending moment in the sections reverses. (b) When the member are subjected to loading eccentric in either side of the axis. (c) When the members are subjected to accidental lateral loads . (d) All of the above

Description : A doubly reinforced section is used (a) When the members are subjected to alternate external loads and the bending moment in the sections reverses. (b) When the member are subjected to loading eccentric in ... . (c) When the members are subjected to accidental lateral loads . (d) All of the above

Last Answer : (d) All of the above

Pick up the correct statement from the following: (A) Long tangent sections exceeding 3 km in length should be avoided (B) Curve length should be at least 150 metres for a deflection angle of 5 degree (C) For every degree decrease in the deflection angle, 30 metre length of curve to be increased (D) All the above

Description : Pick up the correct statement from the following: (A) Long tangent sections exceeding 3 km in length should be avoided (B) Curve length should be at least 150 metres for a deflection angle of 5 ... decrease in the deflection angle, 30 metre length of curve to be increased (D) All the above

Last Answer : Answer: Option D

The cross-sections for a highway is taken at (A) Right angle to the centre line (B) 30 metres apart (C) Intermediate points having abrupt change in gradient (D) All the above

Description : The cross-sections for a highway is taken at (A) Right angle to the centre line (B) 30 metres apart (C) Intermediate points having abrupt change in gradient (D) All the above

Last Answer : (D) All the above

Steel channel sleepers are provided in bridges with superstructure of a) PSC slab b) PSC girder c) Steel girder* d) RCC Box

Description : Steel channel sleepers are provided in bridges with superstructure of a) PSC slab b) PSC girder c) Steel girder* d) RCC Box

Last Answer : c) Steel girder*

Two shafts in torsion will have equal strength if a. Only diameter of the shafts is same b. Only angle of twist of the shaft is same c. Only material of the shaft is same d. Only torque transmitting capacity of the shaft is same

Description : Two shafts in torsion will have equal strength if a. Only diameter of the shafts is same b. Only angle of twist of the shaft is same c. Only material of the shaft is same d. Only torque transmitting capacity of the shaft is same

Last Answer : d. Only torque transmitting capacity of the shaft is same

In a singly reinforced beam (A) Compression is borne entirely by concrete (B) Steel possesses initial stresses when embedded in concrete (C) Plane sections transverse to the centre line of the beam before bending remain plane after bending (D) Elastic moduli for concrete and steel have different values within the limits of deformation of the beam

Description : In a singly reinforced beam (A) Compression is borne entirely by concrete (B) Steel possesses initial stresses when embedded in concrete (C) Plane sections transverse to the centre line ... Elastic moduli for concrete and steel have different values within the limits of deformation of the beam

Last Answer : Answer: Option C

In symmetrically reinforced sections, shrinkage stresses in concrete and steel are respectively (A) Compressive and tensile (B) Tensile and compressive (C) Both compressive (D) Both tensile

Description : In symmetrically reinforced sections, shrinkage stresses in concrete and steel are respectively (A) Compressive and tensile (B) Tensile and compressive (C) Both compressive (D) Both tensile

Last Answer : Answer: Option D

Steel Beam theory is the method of analysis and a design of [ A ] Singly reinforced sections [ B ] Doubly reinforced sections [ C ] Both (a) and (b) [ D ] Steel structures only

Description : Steel Beam theory is the method of analysis and a design of [ A ] Singly reinforced sections [ B ] Doubly reinforced sections [ C ] Both (a) and (b) [ D ] Steel structures only

Last Answer : [ B ] Doubly reinforced sections

Steel Beam theory is the method of analysis and a design of [ A ] Singly reinforced sections [ B ] Doubly reinforced sections [ C ] Both (a) and (b) [ D ] Steel structures only

Description : Steel Beam theory is the method of analysis and a design of [ A ] Singly reinforced sections [ B ] Doubly reinforced sections [ C ] Both (a) and (b) [ D ] Steel structures only

Last Answer : [ B ] Doubly reinforced sections

Steel Beam theory is a method of designing [ A ] Balanced sections [ B ] Critical sections [ C ] Singly reinforced beams [ D ] Doubly reinforced beams

Description : Steel Beam theory is a method of designing [ A ] Balanced sections [ B ] Critical sections [ C ] Singly reinforced beams [ D ] Doubly reinforced beams

Last Answer : [ D ] Doubly reinforced beams

Suitability of steel for its use in cable is judged by its strength in (A) Tension (B) Compression (C) Torsion (D) Shear

Description : Suitability of steel for its use in cable is judged by its strength in (A) Tension (B) Compression (C) Torsion (D) Shear

Last Answer : (A) Tension

The material used for making torsion bar is (a) Steel (b) Cast iron (c) High carbon steel (d) All of the above

Description : The material used for making torsion bar is (a) Steel (b) Cast iron (c) High carbon steel (d) All of the above

Last Answer : (a) Steel

Boundary layer separation occurs when the (A) Pressure reaches a minimum (B) Cross-section of the channel is reduced (C) Valve is closed in a pipeline (D) Velocity of sound is reached

Description : Boundary layer separation occurs when the (A) Pressure reaches a minimum (B) Cross-section of the channel is reduced (C) Valve is closed in a pipeline (D) Velocity of sound is reached

Last Answer : (B) Cross-section of the channel is reduced

It originates from a Song Dynasty slang term meaning ‘convenient’ or ‘convenience’. What name is given to a Japanese meal, usually served in a lacquered or elaborately decorated box that is divided into sections for holding individual portions of food?

Description : It originates from a Song Dynasty slang term meaning ‘convenient’ or ‘convenience’. What name is given to a Japanese meal, usually served in a lacquered or elaborately decorated box that is divided into sections for holding individual portions of food?

Last Answer : Bento.

Carrier is A. One or more conductors that serve as a common connection for a related group of devices B. a continuous frequency capableof being modulated or impressed witha second signal C. the condition whentwo or more sections attempt to use the same channel at the same time D. a collection of interconnected functional units that provides a data communications service among stations attached tothe network E. None of the above

Description : Carrier is A. One or more conductors that serve as a common connection for a related group of devices B. a continuous frequency capableof being modulated or impressed witha second signal C. ... that provides a data communications service among stations attached tothe network E. None of the above

Last Answer : a continuous frequency capableof being modulated or impressed witha second signa

Pick up the correct statement from the following: (A) Mcg = M M 2 + r2 ) where letters carry their usual meanings (B) Tcp = m 2 + T2 )where letters carry their usual meanings (C) The torque which when acting alone would produce maximum shear stress equal to the maximum shear stress caused by the combined bending and torsion, is called equivalent torque (D) All the above

Description : Pick up the correct statement from the following:  (A) Mcg = M M 2  + r2 ) where letters carry their usual meanings  (B) Tcp = m 2  + T2 )where ... maximum shear stress caused by the combined bending and torsion, is called equivalent  torque  (D) All the above 

Last Answer : (D) All the above 

The ratio of strengths of solid to hollow shafts, both having outside diameter D and hollow having inside diameter D/2, in torsion, is (A) 1/4 (B) 1/2 (C) 1/16 (D) 15/15

Description : The ratio of strengths of solid to hollow shafts, both having outside diameter D and hollow having  inside diameter D/2, in torsion, is  (A) 1/4  (B) 1/2  (C) 1/16  (D) 15/15 

Last Answer : (D) 15/15 

In a ring beam subjected to uniformly distributed load (i) Shear force at mid span is zero (ii) Shear force at mid span is maximum (iii) Torsion at mid span is zero (iv) Torsion at mid span is maximum The correct answer is (A) (i) and (iii) (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv)

Description : In a ring beam subjected to uniformly distributed load (i) Shear force at mid span is zero (ii) Shear force at mid span is maximum (iii) Torsion at mid span is zero (iv) Torsion at mid span is maximum The correct answer ... and (iii) (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv)

Last Answer : Option A

A beam curved in plan is designed for (A) Bending moment and shear (B) Bending moment and torsion (C) Shear and torsion (D) Bending moment, shear and torsion

Description : A beam curved in plan is designed for (A) Bending moment and shear (B) Bending moment and torsion (C) Shear and torsion (D) Bending moment, shear and torsion

Last Answer : Answer: Option D

In prestressed concrete members, the shear force depends upon (a) Distributed load (b) Torsion (c) Concentrated load (d) Variation in net bending moment

Description : In prestressed concrete members, the shear force depends upon (a) Distributed load (b) Torsion (c) Concentrated load (d) Variation in net bending moment

Last Answer : (d) Variation in net bending moment

The size of the mesh at each corner meant for torsion reinforcement in a rectangular slab of size (Lx ´ Ly) is Lx = shorter span Lx = Longer span [ A ] 0.1 Ly x 1 Ly [ B ] 0.2 Ly x 0.2 Ly [ C ] 0.1 Lx x 0.1 Lx [ D ] 0.2 Lx x 0.2 Lx

Description : The size of the mesh at each corner meant for torsion reinforcement in a rectangular slab of size (Lx ´ Ly) is Lx = shorter span Lx = Longer span [ A ] 0.1 Ly x 1 Ly [ B ] 0.2 Ly x 0.2 Ly [ C ] 0.1 Lx x 0.1 Lx [ D ] 0.2 Lx x 0.2 Lx

Last Answer : [ D ] 0.2 Lx x 0.2 Lx

On earth roads, the camber should preferably be (A) 1 in 20 to 1 in 24 (B) 1 in 30 to 1 in 48 (C) 1 in 15 to 1 in 20 (D) 1 in 10 to 1 in 15

Description : On earth roads, the camber should preferably be (A) 1 in 20 to 1 in 24 (B) 1 in 30 to 1 in 48 (C) 1 in 15 to 1 in 20 (D) 1 in 10 to 1 in 15

Last Answer : Answer: Option A

Pick up the correct statement from the following: (A) Various geometric design features and generally guided by ruling design speed (B) The design speed for a given highway should preferably be uniform (C) Abrupt change in the design speed should not be permitted (D) All the above

Description : Pick up the correct statement from the following: (A) Various geometric design features and generally guided by ruling design speed (B) The design speed for a given highway should preferably be uniform (C) Abrupt change in the design speed should not be permitted (D) All the above

Last Answer : Answer: Option D

Pick up the incorrect statement from the following: (A) Space between the exterior walls of a warehouse and bag piles should be 30 cm (B) Cement bags should preferably be piled on wooden planks (C) Width and height of the pile should not exceed 3 m and 2.70 m respectively (D) None of these

Description : Pick up the incorrect statement from the following: (A) Space between the exterior walls of a warehouse and bag piles should be 30 cm (B) Cement bags should preferably be piled on wooden planks (C) Width and height of the pile should not exceed 3 m and 2.70 m respectively (D) None of these

Last Answer : Answer: Option D

For a channel section, the shear centre lies at a distance of (A) dbt/2I (B) d²bt/3I (C) d²b²t/4I (D) db²t/5I

Description : For a channel section, the shear centre lies at a distance of  (A) dbt/2I (B) d²bt/3I (C) d²b²t/4I (D) db²t/5I

Last Answer : (C) d²b²t/4I

20. The velocity of flow is same at all points in the cross-section of a channel. A) True B) False

Description : 20. The velocity of flow is same at all points in the cross-section of a channel. A) True B) False

Last Answer : B

The most efficient section of a channel is (A) Triangular (B) Rectangular (C) Square (D) Trapezoidal

Description : The most efficient section of a channel is (A) Triangular (B) Rectangular (C) Square (D) Trapezoidal

Last Answer : Answer: Option D

channel is said to be of most economical cross-section, if (A) It gives maximum discharge for a given cross-sectional area and bed slope (B) It has minimum wetted perimeter (C) It involves lesser excavation for the designed amount of discharge (D) All of the above

Description : channel is said to be of most economical cross-section, if (A) It gives maximum discharge for a given cross-sectional area and bed slope (B) It has minimum wetted perimeter (C) It involves lesser excavation for the designed amount of discharge (D) All of the above

Last Answer : Answer: Option D

The highest efficiency is obtained with a channel of __________ section. (A) Circular (B) Square (C) Rectangular (D) Trapezoidal

Description : The highest efficiency is obtained with a channel of __________ section. (A) Circular (B) Square (C) Rectangular (D) Trapezoidal

Last Answer : Answer: Option D

The discharge through a channel of circular section will be maximum when the depth of water is __________ the diameter of the circular channel. (A) 0.34 times (B) 0.67 times (C) 0.81 times (D) 0.95 times

Description : The discharge through a channel of circular section will be maximum when the depth of water is __________ the diameter of the circular channel. (A) 0.34 times (B) 0.67 times (C) 0.81 times (D) 0.95 times

Last Answer : Answer: Option D

The discharge through a channel of rectangular section will be maximum, if (A) Its depth is twice the breadth (B) Its breadth is twice the depth (C) Its depth is thrice the breadth (D) Its breadth is thrice the depth

Description : The discharge through a channel of rectangular section will be maximum, if (A) Its depth is twice the breadth (B) Its breadth is twice the depth (C) Its depth is thrice the breadth (D) Its breadth is thrice the depth

Last Answer : Answer: Option B

The discharge through a channel of trapezoidal section is maximum when (A) Width of channel at the top is equal to twice the width at the bottom (B) Depth of channel is equal to the width at the bottom (C) The sloping side is equal to half the width at the top (D) The sloping side is equal to the width at the bottom

Description : The discharge through a channel of trapezoidal section is maximum when (A) Width of channel at the top is equal to twice the width at the bottom (B) Depth of channel is equal to the width at the bottom ... equal to half the width at the top (D) The sloping side is equal to the width at the bottom

Last Answer : Answer: Option C

The velocity through a channel of circular section will be maximum when the depth of water is __________ the diameter of the circular channel. (A) 0.34 times (B) 0.67 times (C) 0.81 times (D) 0.95 times

Description : The velocity through a channel of circular section will be maximum when the depth of water is __________ the diameter of the circular channel. (A) 0.34 times (B) 0.67 times (C) 0.81 times (D) 0.95 times

Last Answer : Answer: Option C

The most economical section of a trapezoidal channel is one which has hydraulic mean depth equal to (A) 1/2 × depth (B) 1/2 × breadth (C) 1/2 × sloping side (D) 1/4 × (depth + breadth)

Description : The most economical section of a trapezoidal channel is one which has hydraulic mean depth equal to (A) 1/2 × depth (B) 1/2 × breadth (C) 1/2 × sloping side (D) 1/4 × (depth + breadth)

Last Answer : Answer: Option A

The most economical section of a rectangular channel is one which has hydraulic mean depth or hydraulic radius equal to (A) Half the depth (B) Half the breadth (C) Twice the depth (D) Twice the breadth

Description : The most economical section of a rectangular channel is one which has hydraulic mean depth or hydraulic radius equal to (A) Half the depth (B) Half the breadth (C) Twice the depth (D) Twice the breadth

Last Answer : Answer: Option A