The presence of these pollutants can cause a series of problems. The main problems that are caused______ • are fouling, • limestone formation, • corrosion and biological • All of the above

The presence of these pollutants can cause a series of problems. The main problems that are caused______
• are fouling,
• limestone formation,
• corrosion and biological
• All of the above
by

1 Answer

Answer :

All of the above
by

Related questions

Pollution caused by cooling tower includes 1. Fouling 2. Limestone formation 3. Corrosion 4. All of above

Description : Pollution caused by cooling tower includes 1. Fouling 2. Limestone formation 3. Corrosion 4. All of above

Last Answer : All of above

Presence of sulphur in gasoline (A) Leads to corrosion (B) Increases lead susceptibility (C) Decreases gum formation (D) Helps during stabilisatio

Description : Presence of sulphur in gasoline (A) Leads to corrosion (B) Increases lead susceptibility (C) Decreases gum formation (D) Helps during stabilisatio

Last Answer : (A) Leads to corrosion

Presence of a certain minimum quantity of fluorine is desirable in potable water to prevent (A) Dental cavities (B) Scale formation (C) Water-borne disease (D) Corrosion

Description : Presence of a certain minimum quantity of fluorine is desirable in potable water to prevent (A) Dental cavities (B) Scale formation (C) Water-borne disease (D) Corrosion

Last Answer : (A) Dental cavities

Presence of volatile compounds like gasoline, oil, alcohol, ether etc. in municipal sewers may cause (A) Explosion(B) Non biodegradable foam(C) Undesirable plant growth(D) Corrosion

Description : Presence of volatile compounds like gasoline, oil, alcohol, ether etc. in municipal sewers may cause (A) Explosion (B) Non biodegradable foam (C) Undesirable plant growth (D) Corrosion

Last Answer : (A) Explosion

The most prominent single cause of corrosion in boiler-tubes, drums, economisers and steam superheaters in a thermal power plant boiler is the (A) Water alkalinity & leakage (B) Hydrazine addition during feed water treatment (C) Release of non-condensable gas from water in the boiler (D) Scale formation

Description : The most prominent single cause of corrosion in boiler-tubes, drums, economisers and steam superheaters in a thermal power plant boiler is the (A) Water alkalinity & leakage (B) Hydrazine addition during ... treatment (C) Release of non-condensable gas from water in the boiler (D) Scale formation

Last Answer : (C) Release of non-condensable gas from water in the boiler

Weld decay will cause which of the following problems? a) A reduced resistance to corrosion b) a lower tensile strength c) The toughness is reduced d) The hardness will increase

Description : Weld decay will cause which of the following problems? a) A reduced resistance to corrosion b) a lower tensile strength c) The toughness is reduced d) The hardness will increase

Last Answer : a) A reduced resistance to corrosion

The presence of pollutants in the environment is usually expressed in ppm, where ppm stands for: (1) particles per mole (2) purity per microgram (3) pollutant prevent measures (4) parts per million

Description : The presence of pollutants in the environment is usually expressed in ppm, where ppm stands for: (1) particles per mole (2) purity per microgram (3) pollutant prevent measures (4) parts per million

Last Answer : (4) parts per million Explanation: PPM is an abbreviation of Parts Per Million. It is commonly used as a measure of small levels of pollutants in air, water, body fluids, etc. Parts per million is the mass ratio between the pollutant component and the solution.

The presence of pollutants in the environment is usually expressed in ppm, where ppm stands for: (1) particles per mole (2) purity per microgram (3) pollutant prevent measures (4) parts per million

Description : The presence of pollutants in the environment is usually expressed in ppm, where ppm stands for: (1) particles per mole (2) purity per microgram (3) pollutant prevent measures (4) parts per million

Last Answer : parts per million

The pollutants that are present depend on __________ building material, as well. • Cooling tower • Water tower • Steam tower • Fire tower

Description : The pollutants that are present depend on __________ building material, as well. • Cooling tower • Water tower • Steam tower • Fire tower

Last Answer : cooling water

Is formation of limestone a physical or chemical change?

Description : Is formation of limestone a physical or chemical change?

Last Answer : I am not sure but I think it is Physical change.

When limestone is subjected to high temperature and pressure known as Metamorphism, it results in the formation of? a. Granite b. Quicklime c. Sandstone d. Marble

Description : When limestone is subjected to high temperature and pressure known as Metamorphism, it results in the formation of? a. Granite b. Quicklime c. Sandstone d. Marble

Last Answer : d. Marble

The aquifer of a famous artesian formation in the Great Plains is a layer of rock called the: w) Clinton limestone x) Dakota sandstone y) Pierre shale z) Vermont marble

Description : The aquifer of a famous artesian formation in the Great Plains is a layer of rock called the: w) Clinton limestone x) Dakota sandstone y) Pierre shale z) Vermont marble

Last Answer : ANSWER: X -- DAKOTA SANDSTONE

Wrought iron is resistant to rusting and corrosion due to the presence of

Description : Wrought iron is resistant to rusting and corrosion due to the presence of

Last Answer : Wrought iron is resistant to rusting and corrosion due to the presence of A. Cementite `(Fe_(3)C)` B. ... 4)` Slages D. `MnSiO_(3)& FePO_(4)`slages

The presence of which of the following salts in water causes corrosion in steam boilers? (1) Sodium Chloride (2) Magnesium Chloride (3) Calcium bicarbonate (4) Potassium bicarbonate

Description : The presence of which of the following salts in water causes corrosion in steam boilers? (1) Sodium Chloride (2) Magnesium Chloride (3) Calcium bicarbonate (4) Potassium bicarbonate

Last Answer : (2) Magnesium Chloride Explanation: Magnesium chloride is the name for the chemical compound with the formula MgCl2 and its various hydrates MgCl2(H2O)x. These salts are typical ionic halides, being highly soluble in water.

The purpose of an impressed current cathodic protection system aboard ship is to _______________. A. prevent corrosion of the hull, propeller, rudder and line shafting B. neutralize the vessel's stray magnetic fields which would interfere with radar C. protect engine room and deck machinery from oxidation in the presence of salt air D. maintain a minimum constant alternator load to prevent overheating

Description : The purpose of an impressed current cathodic protection system aboard ship is to _______________. A. prevent corrosion of the hull, propeller, rudder and line shafting B. neutralize the vessel's ... the presence of salt air D. maintain a minimum constant alternator load to prevent overheating

Last Answer : Answer: A

Presence of nickel in steel improves its (A) Corrosion resistance (B) Cutting ability (C) Wear resistance (D) All (A), (B) and (C

Description : Presence of nickel in steel improves its (A) Corrosion resistance (B) Cutting ability (C) Wear resistance (D) All (A), (B) and (C

Last Answer : (A) Corrosion resistance

Presence of manganese in alloy steel improves its (A) Corrosion resistance (B) Cutting ability (C) Abrasion resistance & toughness (D) Elasticity & creep resistance

Description : Presence of manganese in alloy steel improves its (A) Corrosion resistance (B) Cutting ability (C) Abrasion resistance & toughness (D) Elasticity & creep resistance

Last Answer : (C) Abrasion resistance & toughness

Presence of cobalt in steel improves its (A) Cutting ability (B) Corrosion resistance (C) Tensile strength

Description : Presence of cobalt in steel improves its (A) Cutting ability (B) Corrosion resistance (C) Tensile strength

Last Answer : (A) Cutting ability

In a gas-liquid shell and tube heat exchanger, the(A) Presence of a non-condensable gas decreases the condensing film co￾efficient (B) Gases under high pressure are routed through the tube side, because high pressure gases are corrosive in nature (C) Gases to be heated/cooled is normally routed through the shell side, because the corrosion caused by the cooling water or steam condensate remain localised to the tubes (D) All 'a', 'b' & 'c'

Description : In a gas-liquid shell and tube heat exchanger, the (A) Presence of a non-condensable gas decreases the condensing film co￾efficient (B) Gases under high pressure are routed through the tube side, because high pressure ... water or steam condensate remain localised to the tubes (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

Pick out the wrong statement. (A) Addition of methane to the furnace atmosphere reduces decarburising by hydrogen (B) Nitrogen in presence of steam decor-burises high carbon steel, whereas hydrocarbon gases carburise the surface of steel at annealing temperatures (C) Active nitrogen (formed by cracking ammonia at the metal surface) cause nitride formation with increase in surface hardness (D) None of these

Description : Pick out the wrong statement. (A) Addition of methane to the furnace atmosphere reduces decarburising by hydrogen (B) Nitrogen in presence of steam decor-burises high carbon steel, whereas hydrocarbon ... the metal surface) cause nitride formation with increase in surface hardness (D) None of these

Last Answer : (D) None of these

The principal aquifer of the artesian wells of Florida is a: w) porous sandstone x) fissured limestone y) series of clay beds z) mass of pumice

Description : The principal aquifer of the artesian wells of Florida is a: w) porous sandstone x) fissured limestone y) series of clay beds z) mass of pumice

Last Answer : ANSWER: X -- FISSURED LIMESTONE

The process of covering water pipes made of Iron with Zinc layer to prevent corrosion is called – (1) Zinc plating (2) Alloy formation (3) Vulcanization (4) Galvanization

Description : The process of covering water pipes made of Iron with Zinc layer to prevent corrosion is called – (1) Zinc plating (2) Alloy formation (3) Vulcanization (4) Galvanization

Last Answer : (4) Galvanization Explanation: Galvanization is the process of applying a protective zinc coating to steel or iron, in order to prevent rusting.

Yield of urea can be increased with excess ammonia and higher pressure & temperature, but because of __________ this is normally not done. (A) Increased biuret formation (B) High corrosion rate (C) Increased cost of equipment (D) All (A), (B) & (C)

Description : Yield of urea can be increased with excess ammonia and higher pressure & temperature, but because of __________ this is normally not done. (A) Increased biuret formation (B) High corrosion rate (C) Increased cost of equipment (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Use of water having dissolved oxygen in boilers promotes (A) Corrosion (B) Sequestration (C) Scale formation(D) None of these

Description : Use of water having dissolved oxygen in boilers promotes (A) Corrosion (B) Sequestration (C) Scale formation (D) None of these

Last Answer : (A) Corrosion

Which of the following is not a result of the excess of impurity in boiler-feed. a) Scale and sludge formation b) Decomposition c) Corrosion, priming and foaming d) Caustic embrittlement

Description : Which of the following is not a result of the excess of impurity in boiler-feed. a) Scale and sludge formation b) Decomposition c) Corrosion, priming and foaming d) Caustic embrittlement

Last Answer : b) Decomposition

The process of covering water pipes made of Iron with Zinc layer to prevent corrosion is called : (1) Zinc plating (2) Alloy formation (3) Vulcanization (4) Galvanization

Description : The process of covering water pipes made of Iron with Zinc layer to prevent corrosion is called : (1) Zinc plating (2) Alloy formation (3) Vulcanization (4) Galvanization

Last Answer : Galvanization

Which metal does not undergo corrosion due to the formation of oxide layer? (1) Copper (2) Iron (3) Aluminium (4) Zinc

Description : Which metal does not undergo corrosion due to the formation of oxide layer? (1) Copper (2) Iron (3) Aluminium (4) Zinc

Last Answer : Aluminium

Which elements increase the corrosion resistance of steel ?

Description : Which elements increase the corrosion resistance of steel ?

Last Answer : Chromium and nickel.

Which element is added in steel to increase resistance to corrosion ?

Description : Which element is added in steel to increase resistance to corrosion ?

Last Answer : Chromium.

Steel Tank in the power sprayer is used to avoid a) Moisturisation b) Corrosion c) Leakages d) Stability

Description : Steel Tank in the power sprayer is used to avoid a) Moisturisation b) Corrosion c) Leakages d) Stability

Last Answer : Corrosion

In cooling tower ,higher temperature __________ corrosion potential • Decrease • Increase • Temperature has no effect on corrosion

Description : In cooling tower ,higher temperature __________ corrosion potential • Decrease • Increase • Temperature has no effect on corrosion

Last Answer : Increase

Dynamite is a tool that can be used to cut down trees. To cut a tree 18 inches in diameter requires five sticks of dynamite: one on the north, south, east and west sides of the tree, and the fifth stick on the side to which the tree should fall. During construction of a dam, a tree 18 inches in diameter was completely covered by water. Since the treetop was fouling the boat's propellers, it had to be cut down. A diver went down and put a stick of dynamite on the four sides of the tree. Since the current is flowing south at 2 knots per hour, on which side of the tree would you instruct the diver to put the fifth stick of dynamite if you wanted the tree to fall north? -Riddles

Description : Dynamite is a tool that can be used to cut down trees. To cut a tree 18 inches in diameter requires five sticks of dynamite: one on the north, south, east and west sides of the tree, and the ... you instruct the diver to put the fifth stick of dynamite if you wanted the tree to fall north? -Riddles

Last Answer : It doesn't matter where the fifth stick is placed, since the tree won't fall in any direction. Being wood, it will float and rise to the surface.

1985 305 bad fuel order and my plugs are fouling out.

Description : 1985 305 bad fuel order and my plugs are fouling out.

Last Answer : Need Answer

Fouling factor' used in the design of a multipass shell and tube heat exchanger is a (A) Non-dimensional factor (B) Factor of safety

Description : Fouling factor' used in the design of a multipass shell and tube heat exchanger is a (A) Non-dimensional factor (B) Factor of safety

Last Answer : (B) Factor of safety

Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger, the shell pressure drop is maximum for orifice baffles (C) S.I. unit of fouling factor is Watt/m2 .°K (D) Longitudinal fins are used in extended surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Description : Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger ... surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Last Answer : (C) S.I. unit of fouling factor is Watt/m2 .°K

Baffles are provided in heat exchangers to increase the (A) Fouling factor (B) Heat transfer area (C) Heat transfer co-efficient (D) Heat transfer rate

Description : Baffles are provided in heat exchangers to increase the (A) Fouling factor (B) Heat transfer area (C) Heat transfer co-efficient (D) Heat transfer rate

Last Answer : (C) Heat transfer co-efficient

Fouling factor (A) Is a dimensionless quantity (B) Does not provide a safety factor for design (C) Accounts for additional resistances to heat flow (D) None of these

Description : Fouling factor (A) Is a dimensionless quantity (B) Does not provide a safety factor for design (C) Accounts for additional resistances to heat flow (D) None of these

Last Answer : (C) Accounts for additional resistances to heat flow

Which characteristic of a fluid is not important in deciding its route in a shell and tube heat exchanger? (A) Corrosiveness (B) Fouling characteristic (C) Viscosity (D) None of these

Description : Which characteristic of a fluid is not important in deciding its route in a shell and tube heat exchanger? (A) Corrosiveness (B) Fouling characteristic (C) Viscosity (D) None of these

Last Answer : (D) None of these

In SI units, fouling factor is expressed in (A) m2°K/W (B) W/m2°K (C) m2°K (D) m°K/W

Description : In SI units, fouling factor is expressed in (A) m2°K/W (B) W/m2°K (C) m2°K (D) m°K/W

Last Answer : (A) m2°K/W

The overall heat transfer co-efficient for a shell and tube heat exchangerfor clean surfaces is U0 = 400 W/m2.K. The fouling factor after one year ofoperation is found to be hd0 = 2000 W/m2.K. The overall heat transfer co￾efficient at this time is(A) 1200 W/m2.K(B) 894 W/m2.K(C) 333 W/m2.K(D) 287 W/m2.K

Description : The overall heat transfer co-efficient for a shell and tube heat exchangerfor clean surfaces is U0 = 400 W/m2 .K. The fouling factor after one year of operation is found to be hd0 = 2000 W/m2 .K. The overall heat transfer co￾efficient ... 1200 W/m2 .K (B) 894 W/m2 .K (C) 333 W/m2 .K (D) 287 W/m2 .K

Last Answer : (C) 333 W/m2 .K

Which of the following parameters of the fluid is not very important, while deciding its route in a shell and tube heat exchanger? (A) Corrosiveness & fouling characteristics (B) Pressure (C) Viscosity (D) Density

Description : Which of the following parameters of the fluid is not very important, while deciding its route in a shell and tube heat exchanger? (A) Corrosiveness & fouling characteristics (B) Pressure (C) Viscosity (D) Density

Last Answer : (D) Density

Which is the best tube arrangement (in a shell and tube heat exchanger) if the fluids are clean and non-fouling? (A) Square pitch (B) Triangular pitch (C) Diagonal square pitch

Description : Which is the best tube arrangement (in a shell and tube heat exchanger) if the fluids are clean and non-fouling? (A) Square pitch (B) Triangular pitch (C) Diagonal square pitch chemical-engineering

Last Answer : (B) Triangular pitch

Fouling factor for a heat exchanger is given by (where, U1 = heat transfer co-efficient of dirty surface U2 = heat transfer co-efficient of clean surface). (A) U1 - U2 (B) 1/U1 - 1/U2 (C) 1/U2 - 1/U1 (D) U2 - U1

Description : Fouling factor for a heat exchanger is given by (where, U1 = heat transfer co-efficient of dirty surface U2 = heat transfer co-efficient of clean surface). (A) U1 - U2 (B) 1/U1 - 1/U2 (C) 1/U2 - 1/U1 (D) U2 - U1

Last Answer : (B) 1/U1 - 1/U2

Which of the following performance characteristics of a S.I engine is not affected by the front end volatility of the petrol used? (A) Vapour locking (B) Hot starting (C) Spark plug fouling (D) All 'a', 'b' & 'c'

Description : Which of the following performance characteristics of a S.I engine is not affected by the front end volatility of the petrol used? (A) Vapour locking (B) Hot starting (C) Spark plug fouling (D) All 'a', 'b' & 'c'

Last Answer : (C) Spark plug fouling

Baffles provided on the shell side of a shell and tube heat exchanger are meant for (A) Providing support for the tubes (B) Improving heat transfer (C) Both 'a' & 'b' (D) Preventing the fouling of tubes & stagnation of shell side fluid

Description : Baffles provided on the shell side of a shell and tube heat exchanger are meant for (A) Providing support for the tubes (B) Improving heat transfer (C) Both 'a' & 'b' (D) Preventing the fouling of tubes & stagnation of shell side fluid

Last Answer : C) Both 'a' & 'b'

When is spark plug fouling most likely to occur? a. In the climb if you have not adjusted the mixture b. Cruise power c. In the descent if you have not adjusted the mixture d. Max take-off power

Description : When is spark plug fouling most likely to occur? a. In the climb if you have not adjusted the mixture b. Cruise power c. In the descent if you have not adjusted the mixture d. Max take-off power

Last Answer : a. In the climb if you have not adjusted the mixture

When is spark plug fouling most likely to occur? a. In the climb if you have not adjusted the mixture b. Cruise power c. In the descent if you have not adjusted the mixture d. Max take-off power

Description : When is spark plug fouling most likely to occur? a. In the climb if you have not adjusted the mixture b. Cruise power c. In the descent if you have not adjusted the mixture d. Max take-off power

Last Answer : a. In the climb if you have not adjusted the mixture

Factors responsible for membrane fouling

Description : Factors responsible for membrane fouling

Last Answer : Factors responsible for membrane fouling: Membrane fouling in almost all membrane processes is normally caused by precipitation and deposition of molecules or particulates on the membrane surface or membrane pores. The consequences of ... 4.Floc size 5. Alkalinity and pH 6.Salinity