At either end of a plane frame, maximum number of possible bending moments, are (A) Zero (B) One (C) Two (D) Three

At either end of a plane frame, maximum number of possible bending moments, are
(A) Zero
(B) One
(C) Two
(D) Three
by

1 Answer

Answer :

(A) Zero
by

Related questions

At either end of a plane frame, maximum number of possible transverse shear forces, are (A) One (B) Two (C) Three (D) Four

Description : At either end of a plane frame, maximum number of possible transverse shear forces, are (A) One (B) Two (C) Three (D) Four

Last Answer : (A) One

A bending moment may be defined as: (A) Arithmetic sum of the moments of all the forces on either side of the section (B) Arithmetic sum of the forces on either side of the section (C) Algebraic sum of the moments of all the forces on either side of the section (D) None of these

Description : A bending moment may be defined as: (A) Arithmetic sum of the moments of all the forces on either side of the section (B) Arithmetic sum of the forces on either side of the section (C) Algebraic sum of the moments of all the forces on either side of the section (D) None of these

Last Answer : (C) Algebraic sum of the moments of all the forces on either side of the section

According to principle of moments (A) If a system of coplanar forces is in equilibrium, then their algebraic sum is zero (B) If a system of coplanar forces is in equilibrium, then the algebraic sum of their moments about any point in their plane is zero (C) The algebraic sum of the moments of any two forces about any point is equal to moment of their resultant about the same point (D) Positive and negative couples can be balanced

Description : According to principle of moments  (A) If a system of coplanar forces is in equilibrium, then their algebraic sum is zero  (B) If a system of coplanar forces is in equilibrium, then the ... of  their resultant about the same point  (D) Positive and negative couples can be balanced

Last Answer : (C) The algebraic sum of the moments of any two forces about any point is equal to moment of  their resultant about the same point 

While using three moments equation, a fixed end of a continuous beam is replaced by an additional span of (A) Zero length (B) Infinite length (C) Zero moment of inertia(D) None of the above

Description : While using three moments equation, a fixed end of a continuous beam is replaced by an additional span of (A) Zero length (B) Infinite length (C) Zero moment of inertia (D) None of the above

Last Answer : (A) Zero length

A shaft is said to be in pure torsion if a. Turning moment is applied at one end and other end is free b. Turning force is applied at one end and other end is free c. Two opposite turning moments are applied to the shaft d. Combination of torsional load and bending load is applied to the shaft

Description : A shaft is said to be in pure torsion if a. Turning moment is applied at one end and other end is free b. Turning force is applied at one end and other end is free c. Two opposite turning moments are applied to the shaft d. Combination of torsional load and bending load is applied to the shaft

Last Answer : c. Two opposite turning moments are applied to the shaft

By applying the static equations i.e. H V M = 0, to a determinate structure, we may determine (A) Supporting reactions only (B) Shear forces only (C) Bending moments only (D) All the above

Description : By applying the static equations i.e. H V M = 0, to a determinate structure, we may  determine  (A) Supporting reactions only  (B) Shear forces only  (C) Bending moments only  (D) All the above

Last Answer : (D) All the above

The areas of cross-section of a square beam and a circular beam subjected to equal bending moments, are same. (A) Circular beam is more economical (B) Square beam is more economical (C) Both the beams are equally strong (D) Both the beams are equally economical

Description : The areas of cross-section of a square beam and a circular beam subjected to equal bending  moments, are same.  (A) Circular beam is more economical  (B) Square beam is more economical  (C) Both the beams are equally strong  (D) Both the beams are equally economical 

Last Answer : (B) Square beam is more economical 

To ensure that the hogging bending moment at two points of suspension of a pile of length L equals the sagging moment at its centre, the distances of the points of suspension from either end, is (A) 0.107 L (B) 0.207 L (C) 0.307 L (D) 0.407 L

Description : To ensure that the hogging bending moment at two points of suspension of a pile of length L equals the sagging moment at its centre, the distances of the points of suspension from either end, is (A) 0.107 L (B) 0.207 L (C) 0.307 L (D) 0.407 L

Last Answer : Answer: Option B

A simply supported beam carries two equal concentrated loads W at distances L/3 from either support. The maximum bending moment (A) WL/3 (B) WL/4 (C) 5WL/4 (D) 3WL/12

Description : A simply supported beam carries two equal concentrated loads W at distances L/3 from either support. The maximum bending moment (A) WL/3 (B) WL/4 (C) 5WL/4 (D) 3WL/12

Last Answer : (A) WL/3

If the length of a wall on either side of a lintel opening is at least half of its effective span L, the load W carried by the lintel is equivalent to the weight of brickwork contained in an equilateral triangle, producing a maximum bending moment (A) WL/2 (B) WL/4 (C) WL/6 (D) WL/8

Description : If the length of a wall on either side of a lintel opening is at least half of its effective span L, the load W carried by the lintel is equivalent to the weight of brickwork contained in an equilateral triangle, producing a maximum bending moment (A) WL/2 (B) WL/4 (C) WL/6 (D) WL/8

Last Answer : Answer: Option C

In case of a cantilever beam, bending moment at the fixed end will be (a) Maximum (b) Minimum (c) Zero (d) None

Description : In case of a cantilever beam, bending moment at the fixed end will be (a) Maximum (b) Minimum (c) Zero (d) None

Last Answer : (a) Maximum

In case of a cantilever beam, bending moment at the free end will be (a) Maximum (b) Minimum (c) Zero (d) None

Description : In case of a cantilever beam, bending moment at the free end will be (a) Maximum (b) Minimum (c) Zero (d) None

Last Answer : c) Zero

The algebraic sum of moments of the forces forming couple about any point in their plane is (A) Equal to the moment of the couple (B) Constant (C) Both of above are correct (D) Both of above are wrong

Description : The algebraic sum of moments of the forces forming couple about any point in their plane is  (A) Equal to the moment of the couple  (B) Constant  (C) Both of above are correct  (D) Both of above are wrong 

Last Answer : (A) Equal to the moment of the couple 

A cantilever carrying a uniformly distributed load W over its full length is propped at its free end such that it is at the level of the fixed end. The bending moment will be zero at its free end also at (A) Midpoint of the cantilever (B) Fixed point of the cantilever (C) 1/4th length from free end (D) 3/4th length from free end

Description : A cantilever carrying a uniformly distributed load W over its full length is propped at its free end such that it is at the level of the fixed end. The bending moment will be zero at its free end also at ... point of the cantilever (C) 1/4th length from free end (D) 3/4th length from free end

Last Answer : (D) 3/4th length from free end

In a combined footing for two columns carrying unequal loads, the maximum hogging bending moment occurs at (A) Less loaded column (B) More loaded column (C) A point of the maximum shear force (D) A point of zero shear force

Description : In a combined footing for two columns carrying unequal loads, the maximum hogging bending moment occurs at (A) Less loaded column (B) More loaded column (C) A point of the maximum shear force (D) A point of zero shear force

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) The bending stress in a section is zero at its neutral axis and maximum at the outer fibres (B) The shear stress is zero at the outer fibres and maximum at the neutral axis (C) The bending stress at the outer fibres, is known as principal stress (D) All the above

Description : Pick up the correct statement from the following:  (A) The bending stress in a section is zero at its neutral axis and maximum at the outer fibres  (B) The shear stress is zero at the outer ... (C) The bending stress at the outer fibres, is known as principal stress  (D) All the above 

Last Answer : (D) All the above 

If the shear force along a section of a beam is zero, the bending moment at the section is (A) Zero (B) Maximum (C) Minimum (D) Average of maximum-minimum

Description : If the shear force along a section of a beam is zero, the bending moment at the section is  (A) Zero  (B) Maximum  (C) Minimum  (D) Average of maximum-minimum 

Last Answer : (B) Maximum 

In a loaded beam, the point of contraflexure occurs at a section where (A) Bending moment is minimum (B) Bending moment is zero or changes sign (C) Bending moment is maximum (D) Shearing force is maximum

Description : In a loaded beam, the point of contraflexure occurs at a section where (A) Bending moment is minimum (B) Bending moment is zero or changes sign (C) Bending moment is maximum (D) Shearing force is maximum

Last Answer : Answer: Option B

Introduction of slurry in a plate and frame filter press is done through a plate in each frame. The plate of this filter has a __________ surface. (A) Plane (B) Curved (C) Ribbed (D) Either (A) or (B)

Description : Introduction of slurry in a plate and frame filter press is done through a plate in each frame. The plate of this filter has a __________ surface. (A) Plane (B) Curved (C) Ribbed (D) Either (A) or (B)

Last Answer : (C) Ribbed

.Freely supported beams are assumed to be fixed beams if subjected to a. end loads which makes displacement zero b. end moments c. end couples which makes slope zero d. moments

Description : .Freely supported beams are assumed to be fixed beams if subjected to a. end loads which makes displacement zero b. end moments c. end couples which makes slope zero d. moments

Last Answer : c. end couples which makes slope zero

Independent displacement components at each joint of a rigid-jointed plane frame are (A) Three linear movements (B) Two linear movements and one rotation (C) One linear movement and two rotations (D) Three rotations

Description : Independent displacement components at each joint of a rigid-jointed plane frame are (A) Three linear movements (B) Two linear movements and one rotation (C) One linear movement and two rotations (D) Three rotations

Last Answer : (B) Two linear movements and one rotation

Maximum deflection of a cantilever due to pure bending moment M at its free end, is (A) ML²/3EI (B) ML²/4EI (C) ML²/6EI (D) ML²/2EI

Description : Maximum deflection of a cantilever due to pure bending moment M at its free end, is (A) ML²/3EI (B) ML²/4EI (C) ML²/6EI (D) ML²/2EI

Last Answer : (D) ML²/2EI

In a three hinged arch, the bending moment will be zero (A) At right hinge only (B) At left hinge only (C) At both right and left hinges (D) At all the three hinges

Description : In a three hinged arch, the bending moment will be zero (A) At right hinge only (B) At left hinge only (C) At both right and left hinges (D) At all the three hinges

Last Answer : (D) At all the three hinges

Does a plane of maximum shear stress contain a? (a) Normal stress (b) Bending stress (c) Torsional shear stress (d) None

Description : Does a plane of maximum shear stress contain a? (a) Normal stress (b) Bending stress (c) Torsional shear stress (d) None

Last Answer : (a) Normal stress

A pin-jointed plane frame is unstable if (A) (m + r) < 2j (B) (m + r) = 2j (C) (m + r) > 2j (D) None of the above Where m is number of members, r is reaction components and j is number of joints

Description : A pin-jointed plane frame is unstable if (A) (m + r) < 2j (B) (m + r) = 2j (C) (m + r) > 2j (D) None of the above Where m is number of members, r is reaction components and j is number of joints

Last Answer : (A) (m + r) < 2j

Number of unknown internal forces in each member of a rigid jointed plane frame is (A) 1 (B) 2 (C) 3 (D) 6

Description : Number of unknown internal forces in each member of a rigid jointed plane frame is (A) 1 (B) 2 (C) 3 (D) 6

Last Answer : (C) 3

If there are m unknown member forces, r unknown reaction components and j number of joints, then the degree of static indeterminacy of a pin-jointed plane frame is given by (A) m + r + 2j (B) m - r + 2j (C) m + r - 2j (D) m + r - 3j

Description : If there are m unknown member forces, r unknown reaction components and j number of joints, then the degree of static indeterminacy of a pin-jointed plane frame is given by (A) m + r + 2j (B) m - r + 2j (C) m + r - 2j (D) m + r - 3j

Last Answer : (C) m + r - 2j

A rigid-jointed plane frame is stable and statically determinate if (A) (m + r) = 2j (B) (m + r) = 3j (C) (3m + r) = 3j (D) (m + 3r) = 3j Where m is number of members, r is reaction components and j is number of joints

Description : A rigid-jointed plane frame is stable and statically determinate if (A) (m + r) = 2j (B) (m + r) = 3j (C) (3m + r) = 3j (D) (m + 3r) = 3j Where m is number of members, r is reaction components and j is number of joints

Last Answer : (C) (3m + r) = 3j

Pick up the correct assumption of the theory of simple bending (A) The value of the Young's modulus is the same in tension as well as in compression (B) Transverse section of a beam remains plane before and after bending (C) The material of the beam is homogeneous and isotropic (D) All the above

Description : Pick up the correct assumption of the theory of simple bending  (A) The value of the Young's modulus is the same in tension as well as in compression  (B) Transverse section of a beam remains ... bending  (C) The material of the beam is homogeneous and isotropic  (D) All the above

Last Answer : (D) All the above

In a singly reinforced beam (A) Compression is borne entirely by concrete (B) Steel possesses initial stresses when embedded in concrete (C) Plane sections transverse to the centre line of the beam before bending remain plane after bending (D) Elastic moduli for concrete and steel have different values within the limits of deformation of the beam

Description : In a singly reinforced beam (A) Compression is borne entirely by concrete (B) Steel possesses initial stresses when embedded in concrete (C) Plane sections transverse to the centre line ... Elastic moduli for concrete and steel have different values within the limits of deformation of the beam

Last Answer : Answer: Option C

Pick up the assumption for the design of a pre-stressed concrete member from the following: (A) A transverse plane section remains a plane after bending (B) During deformation limits, Hook's law is equally applicable to concrete as well as to steel (C) Variation of stress in reinforcement due to changes in external loading is negligible (D) All the above

Description : Pick up the assumption for the design of a pre-stressed concrete member from the following: (A) A transverse plane section remains a plane after bending (B) During deformation limits, Hook's ... of stress in reinforcement due to changes in external loading is negligible (D) All the above

Last Answer : Answer: Option D

In a R.C section under flexure, the assumption that “a plane section before bending remains plane after bending” leads to (a) Strain distribution being linear across the depth (b) Stress distribution being linear across the depth (c) Both stress and strain distribution being linear across the depth (d) Shear stress distribution being uniform along the depth

Description : In a R.C section under flexure, the assumption that a plane section before bending remains plane after bending leads to (a) Strain distribution being linear across the depth (b) ... strain distribution being linear across the depth (d) Shear stress distribution being uniform along the depth

Last Answer : (a) Strain distribution being linear across the depth

The application of elastic theory to the beams is based on the assumption that (a) At any cross-section, plane sections before bending remain plane after bending (b) All tensile stresses are taken up by reinforcement alone and none by the concrete. (c) Steel reinforcement is free from initial stresses when it is embedded in concrete. (d) All of the above

Description : The application of elastic theory to the beams is based on the assumption that (a) At any cross-section, plane sections before bending remain plane after bending (b) All tensile stresses are taken ... reinforcement is free from initial stresses when it is embedded in concrete. (d) All of the above

Last Answer : (d) All of the above

Select the incorrect statement from the following In eccentrically loaded columns, [ A ] The tensile strength of concrete is ignored [ B ] Design stress – strain curve for steel in compression is the same as in tension [ C ] The strain at different points in the section will be same [ D ] Plane section remain plane even after bending

Description : Select the incorrect statement from the following In eccentrically loaded columns, [ A ] The tensile strength of concrete is ignored [ B ] Design stress - strain curve for steel in compression is the ... different points in the section will be same [ D ] Plane section remain plane even after bending

Last Answer : [ C ] The strain at different points in the section will be same

A joint of a frame is subjected to three tensile forces P, Q and R equally inclined to each other. If P is 10 tonnes, the other forces will be (A) Q = 10 tonnes and R = zero (B) R + 10 tonnes and Q = zero (C) Q + R = 10 tonnes (D) Q and R each is equal to 10 tonnes

Description : A joint of a frame is subjected to three tensile forces P, Q and R equally inclined to each other. If P is 10 tonnes, the other forces will be (A) Q = 10 tonnes and R = zero (B) R + 10 tonnes and Q = zero (C) Q + R = 10 tonnes (D) Q and R each is equal to 10 tonnes

Last Answer : (D) Q and R each is equal to 10 tonnes

Transition curves are introduced at either end of a circular curve, to obtain (A) Gradually decrease of curvature from zero at the tangent point to the specified quantity at the junction of the transition curve with main curve (B) Gradual increase of super-elevation from zero at the tangent point to the specified amount at the junction of the transition curve with main curve (C) Gradual change of gradient from zero at the tangent point to the specified amount at the junction of the transition curve with main curve (D) None of these

Description : Transition curves are introduced at either end of a circular curve, to obtain (A) Gradually decrease of curvature from zero at the tangent point to the specified quantity at the junction of the ... specified amount at the junction of the transition curve with main curve (D) None of these

Last Answer : (B) Gradual increase of super-elevation from zero at the tangent point to the specified amount at the junction of the transition curve with main curve

A doubly reinforced section is used (a) When the members are subjected to alternate external loads and the bending moment in the sections reverses. (b) When the member are subjected to loading eccentric in either side of the axis. (c) When the members are subjected to accidental lateral loads . (d) All of the above

Description : A doubly reinforced section is used (a) When the members are subjected to alternate external loads and the bending moment in the sections reverses. (b) When the member are subjected to loading eccentric in ... . (c) When the members are subjected to accidental lateral loads . (d) All of the above

Last Answer : (d) All of the above

If three forces acting in one plane upon a rigid body, keep it in equilibrium, then they must either (A) Meet in a point (B) Be all parallel (C) At least two of them must meet (D) All the above are correct

Description : If three forces acting in one plane upon a rigid body, keep it in equilibrium, then they must either (A) Meet in a point (B) Be all parallel (C) At least two of them must meet (D) All the above are correct

Last Answer : (D) All the above are correct

The 'fix' of a plane table from three known points, is good, if (A) Middle station is nearest (B) Middle station is farthest (C) Either the right or left station is nearest (D) None of these

Description : The 'fix' of a plane table from three known points, is good, if  (A) Middle station is nearest  (B) Middle station is farthest  (C) Either the right or left station is nearest  (D) None of these 

Last Answer : (A) Middle station is nearest 

The operation of resection involves the following steps 1. Rough orientation of the plane table 2. The three lines form a triangle of error 3. Drawing lines back through the three control points 4. Select a point in the triangle of error such that each ray is equally rotated either clockwise or anti clockwise 5. The points obtained by three rays are the correct location. The correct sequence is (A) 1, 3, 2, 4, 5 (B) 1, 2, 3, 4, 5 (C) 1, 4, 3, 2, 5 (D) 1, 3, 2, 4, 5

Description : The operation of resection involves the following steps 1. Rough orientation of the plane table 2. The three lines form a triangle of error 3. Drawing lines back through the three control points 4. Select a point in the triangle of error ... 2, 3, 4, 5 (C) 1, 4, 3, 2, 5 (D) 1, 3, 2, 4, 5

Last Answer : (A) 1, 3, 2, 4, 5

Degree of static indeterminacy of a rigid-jointed plane frame having 15 members, 3 reaction components and 14 joints is (A) 2 (B) 3 (C) 6 (D) 8

Description : Degree of static indeterminacy of a rigid-jointed plane frame having 15 members, 3 reaction components and 14 joints is (A) 2 (B) 3 (C) 6 (D) 8

Last Answer : (C) 6

Degree of kinematic indeterminacy of a pin-jointed plane frame is given by (A) 2j - r (B) j - 2r (C) 3j - r (D) 2j + r

Description : Degree of kinematic indeterminacy of a pin-jointed plane frame is given by (A) 2j - r (B) j - 2r (C) 3j - r (D) 2j + r

Last Answer : (A) 2j - r

If in a pin-jointed plane frame (m + r) > 2j, then the frame is (A) Stable and statically determinate (B) Stable and statically indeterminate (C) Unstable (D) None of the above

Description : If in a pin-jointed plane frame (m + r) > 2j, then the frame is (A) Stable and statically determinate (B) Stable and statically indeterminate (C) Unstable (D) None of the above

Last Answer : (B) Stable and statically indeterminate

The reaction at the supports will be vertical to the plane of the support if the frame structure rests on (A) Roller supports (B) Free supports (C) Hinged supports (D) All the above

Description : The reaction at the supports will be vertical to the plane of the support if the frame structure rests  on  (A) Roller supports  (B) Free supports  (C) Hinged supports  (D) All the above 

Last Answer : (D) All the above 

When loads are applied proportionately to a frame structure containing its members in one plane, the structure is called (A) Grid frame (B) Plane frame (C) Space frame (D) Truss frame

Description : When loads are applied proportionately to a frame structure containing its members in one plane, the structure is called (A) Grid frame (B) Plane frame (C) Space frame (D) Truss frame

Last Answer : (C) Space frame

The algebraic sum of moments of the forces forming couple about any point in their plane is?

Description : The algebraic sum of moments of the forces forming couple about any point in their plane is?

Last Answer : The algebraic sum of moments of the forces forming couple about any point in their plane is equal to the moment of the couple.

In continuous beam if it is end is fixed supported the bending moment will be a. zero b. neglected c. infinite

Description : In continuous beam if it is end is fixed supported the bending moment will be a. zero b. neglected c. infinite

Last Answer : a. zero

In continuous beam if it is end simply supported the bending moment will be a. zero b. neglected c. infinite

Description : In continuous beam if it is end simply supported the bending moment will be a. zero b. neglected c. infinite

Last Answer : a. zero