At either end of a plane frame, maximum number of possible transverse shear forces, are (A) One (B) Two (C) Three (D) Four

At either end of a plane frame, maximum number of possible transverse shear forces, are
(A) One
(B) Two
(C) Three
(D) Four
by

1 Answer

Answer :

(A) One
by

Related questions

At either end of a plane frame, maximum number of possible bending moments, are (A) Zero (B) One (C) Two (D) Three

Description : At either end of a plane frame, maximum number of possible bending moments, are (A) Zero (B) One (C) Two (D) Three

Last Answer : (A) Zero

When equal and opposite forces applied to a body, tend to elongate it, the stress so produced, is called (A) Shear stress (B) Compressive stress (C) Tensile stress (D) Transverse stress

Description : When equal and opposite forces applied to a body, tend to elongate it, the stress so produced, is called (A) Shear stress (B) Compressive stress (C) Tensile stress (D) Transverse stress

Last Answer : (C) Tensile stress

The shear force on a simply supported beam is proportional to (A) Displacement of the neutral axis (B) Sum of the forces (C) Sum of the transverse forces (D) Algebraic sum of the transverse forces of the section

Description : The shear force on a simply supported beam is proportional to (A) Displacement of the neutral axis (B) Sum of the forces (C) Sum of the transverse forces (D) Algebraic sum of the transverse forces of the section

Last Answer : (D) Algebraic sum of the transverse forces of the section

Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension. a) True b) False

Description : Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension. a) True b) False

Last Answer : b) False

Number of unknown internal forces in each member of a rigid jointed plane frame is (A) 1 (B) 2 (C) 3 (D) 6

Description : Number of unknown internal forces in each member of a rigid jointed plane frame is (A) 1 (B) 2 (C) 3 (D) 6

Last Answer : (C) 3

If there are m unknown member forces, r unknown reaction components and j number of joints, then the degree of static indeterminacy of a pin-jointed plane frame is given by (A) m + r + 2j (B) m - r + 2j (C) m + r - 2j (D) m + r - 3j

Description : If there are m unknown member forces, r unknown reaction components and j number of joints, then the degree of static indeterminacy of a pin-jointed plane frame is given by (A) m + r + 2j (B) m - r + 2j (C) m + r - 2j (D) m + r - 3j

Last Answer : (C) m + r - 2j

If three forces acting in one plane upon a rigid body, keep it in equilibrium, then they must either (A) Meet in a point (B) Be all parallel (C) At least two of them must meet (D) All the above are correct

Description : If three forces acting in one plane upon a rigid body, keep it in equilibrium, then they must either (A) Meet in a point (B) Be all parallel (C) At least two of them must meet (D) All the above are correct

Last Answer : (D) All the above are correct

A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Last Answer : a) PSinθ(Sinθ+Cosθ)/hl

A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Last Answer : a) PSinθ(Sinθ+Cosθ)/hl

If the maximum shear stress at the end of a simply supported R.C.C. beam of 6 m effective span is 10 kg/cm2 , the share stirrups are provided for a distance from either end where, is (A) 50 cm (B) 100 cm(C) 150 cm (D) 200 cm

Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 6 m effective span is 10 kg/cm2 , the share stirrups are provided for a distance from either end where, is (A) 50 cm (B) 100 cm (C) 150 cm (D) 200 cm

Last Answer : Answer: Option C

If L is the effective span of a R.C.C. beam which is subjected to maximum shear qmax at the ends, the distance from either end over which stirrups for the shear, are provided, is (A) (L/2) (1 - 3/qmax) (B) (L/3) (1 - 5/qmax) (C) (L/2) (1 - 5/qmax) (D) (L/2) (1 - 2/qmax)

Description : If L is the effective span of a R.C.C. beam which is subjected to maximum shear qmax at the ends, the distance from either end over which stirrups for the shear, are provided, is (A) (L/2) (1 - 3/qmax) (B) (L/3) (1 - 5/qmax) (C) (L/2) (1 - 5/qmax) (D) (L/2) (1 - 2/qmax)

Last Answer : Answer: Option C

determining stresses in frames by methods of sections, the frame is divided into two parts by an imaginary section drawn in such a way as not to cut more than (A) Two members with unknown forces of the frame (B) Three members with unknown forces of the frame (C) Four members with unknown forces of the frame (D) Three members with known forces of the frame

Description : determining stresses in frames by methods of sections, the frame is divided into two parts by an imaginary section drawn in such a way as not to cut more than (A) Two members with unknown forces ... C) Four members with unknown forces of the frame (D) Three members with known forces of the frame

Last Answer : (B) Three members with unknown forces of the frame

For shear strength, triaxial shear test is suitable because (A) It can be performed under all three drainage conditions (B) Precise measurement of the pore pressure and volume change during the test is possible (C) Stress distribution on the failure plane, is uniform (D) All the above

Description : For shear strength, triaxial shear test is suitable because (A) It can be performed under all three drainage conditions (B) Precise measurement of the pore pressure and volume change during the test is possible (C) Stress distribution on the failure plane, is uniform (D) All the above

Last Answer : (D) All the above

A triaxial shear test is preferred to direct shear test, because (A) It can be performed under all three drainage conditions with complete control (B) Precise measurement of pore pressure and change in volume during test, is not possible (C) Stress distribution on the failure plane, is non uniform (D) None of these

Description : A triaxial shear test is preferred to direct shear test, because (A) It can be performed under all three drainage conditions with complete control (B) Precise measurement of pore pressure and change in ... possible (C) Stress distribution on the failure plane, is non uniform (D) None of these

Last Answer : Answer: Option A

Struts are load carrying members of a frame structure which are subjected to (A) Axial tension loads (B) Axial compressive loads (C) Torsional loads (D) Transverse loads

Description : Struts are load carrying members of a frame structure which are subjected to  (A) Axial tension loads  (B) Axial compressive loads  (C) Torsional loads  (D) Transverse loads 

Last Answer : (B) Axial compressive loads 

Ties are load carrying members of a frame, which are subjected to (A) Transverse loads (B) Axial tension loads (C) Axial compressive loads (D) Torsional loads

Description : Ties are load carrying members of a frame, which are subjected to  (A) Transverse loads  (B) Axial tension loads  (C) Axial compressive loads  (D) Torsional loads 

Last Answer : (B) Axial tension loads 

Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Description : Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Last Answer : b) 1.21P/hl

Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Description : Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Last Answer : b) 1.21P/hl

The maximum shear stress occurs on the filament which makes an angle with the horizontal plane equal to (A) 30° (B) 45° (C) 60° (D) 90

Description : The maximum shear stress occurs on the filament which makes an angle with the horizontal plane equal to (A) 30° (B) 45° (C) 60° (D) 90

Last Answer : (B) 45°

Pick up the correct statement from the following: (A) An unconfined compression test is a special case of triaxial compression test (B) An unconfined compression test is a special case of direct shear test (C) The confining pressure is maximum during an unconfined compression test (D) The cylindrical specimen of a soil is subjected to major principal stress till it fails due to shearing along the plane of the failure

Description : Pick up the correct statement from the following: (A) An unconfined compression test is a special case of triaxial compression test (B) An unconfined compression test is a special case of direct ... subjected to major principal stress till it fails due to shearing along the plane of the failure

Last Answer : Option A

Pick up the correct statement from the following: (A) Failure plane carries maximum shear stress (B) Failure plane does not carry maximum shear stress (C) Failure plane carries shear stress equal to maximum shear stress (D) None of these

Description : Pick up the correct statement from the following: (A) Failure plane carries maximum shear stress (B) Failure plane does not carry maximum shear stress (C) Failure plane carries shear stress equal to maximum shear stress (D) None of these

Last Answer : Option B

A joint of a frame is subjected to three tensile forces P, Q and R equally inclined to each other. If P is 10 tonnes, the other forces will be (A) Q = 10 tonnes and R = zero (B) R + 10 tonnes and Q = zero (C) Q + R = 10 tonnes (D) Q and R each is equal to 10 tonnes

Description : A joint of a frame is subjected to three tensile forces P, Q and R equally inclined to each other. If P is 10 tonnes, the other forces will be (A) Q = 10 tonnes and R = zero (B) R + 10 tonnes and Q = zero (C) Q + R = 10 tonnes (D) Q and R each is equal to 10 tonnes

Last Answer : (D) Q and R each is equal to 10 tonnes

Introduction of slurry in a plate and frame filter press is done through a plate in each frame. The plate of this filter has a __________ surface. (A) Plane (B) Curved (C) Ribbed (D) Either (A) or (B)

Description : Introduction of slurry in a plate and frame filter press is done through a plate in each frame. The plate of this filter has a __________ surface. (A) Plane (B) Curved (C) Ribbed (D) Either (A) or (B)

Last Answer : (C) Ribbed

Pick up the correct assumption of the theory of simple bending (A) The value of the Young's modulus is the same in tension as well as in compression (B) Transverse section of a beam remains plane before and after bending (C) The material of the beam is homogeneous and isotropic (D) All the above

Description : Pick up the correct assumption of the theory of simple bending  (A) The value of the Young's modulus is the same in tension as well as in compression  (B) Transverse section of a beam remains ... bending  (C) The material of the beam is homogeneous and isotropic  (D) All the above

Last Answer : (D) All the above

In a singly reinforced beam (A) Compression is borne entirely by concrete (B) Steel possesses initial stresses when embedded in concrete (C) Plane sections transverse to the centre line of the beam before bending remain plane after bending (D) Elastic moduli for concrete and steel have different values within the limits of deformation of the beam

Description : In a singly reinforced beam (A) Compression is borne entirely by concrete (B) Steel possesses initial stresses when embedded in concrete (C) Plane sections transverse to the centre line ... Elastic moduli for concrete and steel have different values within the limits of deformation of the beam

Last Answer : Answer: Option C

Pick up the assumption for the design of a pre-stressed concrete member from the following: (A) A transverse plane section remains a plane after bending (B) During deformation limits, Hook's law is equally applicable to concrete as well as to steel (C) Variation of stress in reinforcement due to changes in external loading is negligible (D) All the above

Description : Pick up the assumption for the design of a pre-stressed concrete member from the following: (A) A transverse plane section remains a plane after bending (B) During deformation limits, Hook's ... of stress in reinforcement due to changes in external loading is negligible (D) All the above

Last Answer : Answer: Option D

What is the maximum number of open bays if transverse zig zag bracing is installed along the width of a birdcage scaffold? a. Four b. Three c. Five d. Six

Description : What is the maximum number of open bays if transverse zig zag bracing is installed along the width of a birdcage scaffold? a. Four b. Three c. Five d. Six

Last Answer : b. Three

Independent displacement components at each joint of a rigid-jointed plane frame are (A) Three linear movements (B) Two linear movements and one rotation (C) One linear movement and two rotations (D) Three rotations

Description : Independent displacement components at each joint of a rigid-jointed plane frame are (A) Three linear movements (B) Two linear movements and one rotation (C) One linear movement and two rotations (D) Three rotations

Last Answer : (B) Two linear movements and one rotation

A pin-jointed plane frame is unstable if (A) (m + r) < 2j (B) (m + r) = 2j (C) (m + r) > 2j (D) None of the above Where m is number of members, r is reaction components and j is number of joints

Description : A pin-jointed plane frame is unstable if (A) (m + r) < 2j (B) (m + r) = 2j (C) (m + r) > 2j (D) None of the above Where m is number of members, r is reaction components and j is number of joints

Last Answer : (A) (m + r) < 2j

A rigid-jointed plane frame is stable and statically determinate if (A) (m + r) = 2j (B) (m + r) = 3j (C) (3m + r) = 3j (D) (m + 3r) = 3j Where m is number of members, r is reaction components and j is number of joints

Description : A rigid-jointed plane frame is stable and statically determinate if (A) (m + r) = 2j (B) (m + r) = 3j (C) (3m + r) = 3j (D) (m + 3r) = 3j Where m is number of members, r is reaction components and j is number of joints

Last Answer : (C) (3m + r) = 3j

At the supports of a simply supported beam, shear forces will be (a) Maximum (b) Minimum (c) Zero (d) None

Description : At the supports of a simply supported beam, shear forces will be (a) Maximum (b) Minimum (c) Zero (d) None

Last Answer : (a) Maximum

By applying the static equations i.e. H V M = 0, to a determinate structure, we may determine (A) Supporting reactions only (B) Shear forces only (C) Bending moments only (D) All the above

Description : By applying the static equations i.e. H V M = 0, to a determinate structure, we may  determine  (A) Supporting reactions only  (B) Shear forces only  (C) Bending moments only  (D) All the above

Last Answer : (D) All the above

Choose the wrong statement (A) Fluids are capable of flowing (B) Fluids conform to the shape of the containing vessels (C) When in equilibrium, fluids cannot sustain tangential forces (D) When in equilibrium, fluids can sustain shear forces

Description : Choose the wrong statement (A) Fluids are capable of flowing (B) Fluids conform to the shape of the containing vessels (C) When in equilibrium, fluids cannot sustain tangential forces (D) When in equilibrium, fluids can sustain shear forces

Last Answer : Answer: Option D

Fluid is a substance that (A) Cannot be subjected to shear forces (B) Always expands until it fills any container (C) Has the same shear stress at a point regardless of its motion (D) Cannot remain at rest under action of any shear force

Description : Fluid is a substance that (A) Cannot be subjected to shear forces (B) Always expands until it fills any container (C) Has the same shear stress at a point regardless of its motion (D) Cannot remain at rest under action of any shear force

Last Answer : Answer: Option D

Transverse fillet welds are under (i) Bending and shear stresses (ii)Compressive and torsion shear stresses (iii)Tensile and compressive stresses (iv)None

Description : Transverse fillet welds are under (i) Bending and shear stresses (ii)Compressive and torsion shear stresses (iii)Tensile and compressive stresses (iv)None

Last Answer : (iv)None

Transverse fillet welds are under (i) Shear stress (ii) Compressive stress (iii) Tensile stress

Description : Transverse fillet welds are under (i) Shear stress (ii) Compressive stress (iii) Tensile stress

Last Answer : (iii) Tensile stress

he transverse fillet welded joints are designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength

Description : he transverse fillet welded joints are designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength

Last Answer : (a) tensile strength

When a body is subjected to transverse vibrations, the stress induced in a body will be A Shear stress B Bending stress C Tensile stress D Compressive stress

Description : When a body is subjected to transverse vibrations, the stress induced in a body will be A Shear stress B Bending stress C Tensile stress D Compressive stress

Last Answer : B Bending stress

During transverse vibrations, shaft is subjected to which type of stresses? A) Tensile stresses B) Torsional shear stress C) Bending stresses D) All of the above

Description : During transverse vibrations, shaft is subjected to which type of stresses? A) Tensile stresses B) Torsional shear stress C) Bending stresses D) All of the above

Last Answer : C) Bending stresses

When a body is subjected to transverse vibrations, the stress induced in a body B will be (A) Shear stress (B) Bending stress (C) Tensile stress (D)Compressive stress

Description : When a body is subjected to transverse vibrations, the stress induced in a body B will be (A) Shear stress (B) Bending stress (C) Tensile stress (D)Compressive stress

Last Answer : (B) Bending stress

When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) bending stress c) tensile stress d) compressive stress

Description : When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) bending stress c) tensile stress d) compressive stress

Last Answer : b) bending stress

During transverse vibrations, shaft is subjected to which type of stresses? a. Tensile stresses b. Torsional shear stress c. Bending stresses d. All of the above

Description : During transverse vibrations, shaft is subjected to which type of stresses? a. Tensile stresses b. Torsional shear stress c. Bending stresses d. All of the above

Last Answer : c. Bending stresses

When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) bending stress c) tensile stress d) compressive stress

Description : When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) bending stress c) tensile stress d) compressive stress

Last Answer : b) bending stress

When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) tensile stress c) compressive stress d) none of the mentioned

Description : When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) tensile stress c) compressive stress d) none of the mentioned

Last Answer : b) tensile stress

Wahl suggested the correction in the stress factor to account for a. the additional transverse shear stress b. stress concentration c. fatigue stress d. axial stress

Description : Wahl suggested the correction in the stress factor to account for a. the additional transverse shear stress b. stress concentration c. fatigue stress d. axial stress

Last Answer : b. stress concentration

A rectangular log of wood is floating in water with a load of 100 N at its centre. The maximum shear force in the wooden log is (A) 50 N at each end (B) 50 N at the centre (C) 100 N at the centre (D) None of these

Description : A rectangular log of wood is floating in water with a load of 100 N at its centre. The maximum shear force in the wooden log is (A) 50 N at each end (B) 50 N at the centre (C) 100 N at the centre (D) None of these

Last Answer : (C) 100 N at the centre

If the maximum shear stress at the end of a simply supported R.C.C. beam of 16 m effective span is 10 kg/cm2 , the length of the beam having nominal reinforcement, is (A) 8 cm (B) 6 m (C) 8 m (D) 10 m

Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 16 m effective span is 10 kg/cm2 , the length of the beam having nominal reinforcement, is (A) 8 cm (B) 6 m (C) 8 m (D) 10 m

Last Answer : Answer: Option C

The 'fix' of a plane table from three known points, is good, if (A) Middle station is nearest (B) Middle station is farthest (C) Either the right or left station is nearest (D) None of these

Description : The 'fix' of a plane table from three known points, is good, if  (A) Middle station is nearest  (B) Middle station is farthest  (C) Either the right or left station is nearest  (D) None of these 

Last Answer : (A) Middle station is nearest 

The operation of resection involves the following steps 1. Rough orientation of the plane table 2. The three lines form a triangle of error 3. Drawing lines back through the three control points 4. Select a point in the triangle of error such that each ray is equally rotated either clockwise or anti clockwise 5. The points obtained by three rays are the correct location. The correct sequence is (A) 1, 3, 2, 4, 5 (B) 1, 2, 3, 4, 5 (C) 1, 4, 3, 2, 5 (D) 1, 3, 2, 4, 5

Description : The operation of resection involves the following steps 1. Rough orientation of the plane table 2. The three lines form a triangle of error 3. Drawing lines back through the three control points 4. Select a point in the triangle of error ... 2, 3, 4, 5 (C) 1, 4, 3, 2, 5 (D) 1, 3, 2, 4, 5

Last Answer : (A) 1, 3, 2, 4, 5

Degree of static indeterminacy of a rigid-jointed plane frame having 15 members, 3 reaction components and 14 joints is (A) 2 (B) 3 (C) 6 (D) 8

Description : Degree of static indeterminacy of a rigid-jointed plane frame having 15 members, 3 reaction components and 14 joints is (A) 2 (B) 3 (C) 6 (D) 8

Last Answer : (C) 6