State maximum power transfer theorem for DC circuit.

State maximum power transfer theorem for DC circuit.
by

1 Answer

Answer :

Maximum power transfer theorem for DC circuit: The maximum power transfer theorem states that the source or a network transfers maximum power to load only when the load resistance is equal to the internal resistance of the source or the network. The internal resistance of the network is the Thevenin equivalent resistance of the network seen between the terminals at which the load is connected when: i) The load is removed (disconnected) ii) All internal independent sources are replaced by their internal resistances.

by

Related questions

Maximum Power Transfer Theorem 1

Description : Maximum Power Transfer Theorem 1

Last Answer : Maximum Power Transfer Theorem 1

For maximum transfer of power, internal resistance of the source should be?

Description : For maximum transfer of power, internal resistance of the source should be?

Last Answer : For maximum transfer of power, internal resistance of the source should be equal to load resistance.

The condition for maximum power in case of D.C. motor is?

Last Answer : (b) Clostridium butylicum Lipase Removal of oil stains

In a D.C. shunt motor, under the conditions of maximum power, the current in the armature will be?

Last Answer : In a D.C. shunt motor, under the conditions of maximum power, the current in the armature will be more than full-load current.

Can you apply Thevenin's theorem in an AC circuit?

Description : Can you apply Thevenin's theorem in an AC circuit?

Last Answer : It  can  be  applied  to  AC  circuits

The power factor of a D.C. circuit is always?

Description : The power factor of a D.C. circuit is always?

Last Answer : The power factor of a D.C. circuit is always unity.

State superposition theorem applied to D.C. circuits.

Description : State superposition theorem applied to D.C. circuits.

Last Answer : Superposition Theorem applied to D.C. circuits: Superposition theorem states that in any linear, bilateral, multisource network, the response (voltage across any element or current through any ... each source acting alone, while the other sources are replaced by their internal resistances.

In which fault the maximum short circuit current occurs?

Description : In which fault the maximum short circuit current occurs?

Last Answer : In three phase bolted fault the maximum short circuit occurs.

What is the maximum number of circuit breakers in a panel?

Description : What is the maximum number of circuit breakers in a panel?

Last Answer : It depends on that which type of panel is this.

_______ electric power is the most common method used by electrical grids to transfer power.

Description : _______ electric power is the most common method used by electrical grids to transfer power.  (A) One-phase (B) Two-phase (C) Three-phase (D) None of the above

Last Answer : Three-phase electric power is the most common method used by electrical grids to transfer power. 

An independent voltage source in series with an impedance ZS=R+jXS delivers a maximum average power to

Description :  An independent voltage source in series with an impedance ZS=R+jXS delivers a maximum average power to a load impedance ZL when A) ZL = R B) ZL = jXS C) ZL = R-jXS D) ZL = R+jXS 

Last Answer :  An independent voltage source in series with an impedance ZS=R+jXS delivers a maximum average power to a load impedance ZL when ZL = R-jXS

Define- (i) Node (ii) Loop for a DC circuit

Description : Define- (i) Node (ii) Loop for a DC circuit

Last Answer : Ans: i) Node: A point or junction at which two or more elements of network are connected is called as node. ii) Loop: A closed path for flow of current in an electrical circuit is called loop.

For a DC circuit capacitor is

Description : For a DC circuit capacitor is

Last Answer : For a DC circuit capacitor is virtually an open circuit

A circuit that binds the upper or lower extreme of a waveform to a fixed DC voltage level is called ______

Description : A circuit that binds the upper or lower extreme of a waveform to a fixed DC voltage level is called ______ A) DC voltage restorer B) Clamping circuit C) Both A and B D) None of these

Last Answer : A circuit that binds the upper or lower extreme of a waveform to a fixed DC voltage level is called ______ A) DC voltage restorer B) Clamping circuit C) Both A and B D) None of these

Consider a circuit with three parallel branches connected across a DC supply. What is the ratio of the branch

Description : Consider a circuit with three parallel branches connected across a DC supply. What is the ratio of the branch currents I1 : I2 : I3 if the branch resistances are in the ratio of 2 : 3 : 4 respectively? A) 2 : 3 : 4 B) 6 : 4 : 3 C) 4 : 3 : 2 D) None of these

Last Answer : Consider a circuit with three parallel branches connected across a DC supply. What is the ratio of the branch currents I1 : I2 : I3 if the branch resistances are in the ratio of 2 : 3 : 4 respectively? A) 2 : 3 : 4 B) 6 : 4 : 3 C) 4 : 3 : 2 D) None of these

Which D.C. motor has got maximum self relieving property ?

Last Answer : Series motor has got maximum self relieving property.

D.C. generators are normally designed for maximum efficiency around?

Last Answer : D.C. generators are normally designed for maximum efficiency around full-load.

The condition for maximum efficiency for a D.C. generator is?

Last Answer : The condition for maximum efficiency for a D.C. generator is variable losses equal to constant losses.

The reactive power transfer over a line mainly depends on

Description : The reactive power transfer over a line mainly depends on

Last Answer : The reactive power transfer over a line mainly depends on lVsl- lVRl

A DC voltage source is connected across a series RLC circuit. Under steady-state conditions, the applied DC

Description : A DC voltage source is connected across a series RLC circuit. Under steady-state conditions, the applied DC voltage drops entirely across the

Last Answer : A DC voltage source is connected across a series RLC circuit. Under steady-state conditions, the applied DC voltage drops entirely across the C only

A certain power MOSFET has a maximum junction temperature specification of 1500o C, a junction-to-case

Description : A certain power MOSFET has a maximum junction temperature specification of 1500o C, a junction-to-case thermal resistance of 1.00 C/W, and a junction-to ambient thermal resistance of 600 C/W. If the ambient temperature is 300o C ... the device will be A) 1.52 W B) 1.72 W C) 1.92W D) 2.00 W

Last Answer : A certain power MOSFET has a maximum junction temperature specification of 1500o C, a junction-to-case thermal resistance of 1.00 C/W, and a junction-to ambient thermal resistance of  ... 300o C, then the maximum allowable power dissipation in the device will be 2.00 W 

The maximum reluctance power of a salient-pole synchronous motor having direct-axis reactance, 1.0 pu and

Description : The maximum reluctance power of a salient-pole synchronous motor having direct-axis reactance, 1.0 pu and quadrature-axis reactance, 0.5 pu, and input voltage, 1.0 pu is (A) 0.25 pu (B) 0.5 pu (C) 1.0 pu (D) 1.5 pu

Last Answer : The maximum reluctance power of a salient-pole synchronous motor having direct-axis reactance, 1.0 pu and quadrature-axis reactance, 0.5 pu, and input voltage, 1.0 pu is 0.5 pu

"Maximum power output is obtained from a network when the load resistance...

Description : "Maximum power output is obtained from a network when the load resistance is equal to the output resistance of the network as seen from the terminals of the load". The above statement is associated with?

Last Answer : "Maximum power output is obtained from a network when the load resistance is equal to the output resistance of the network as seen from the terminals of the load". The above statement is associated with Maximum power transfer theorem.

The mechanical power developed by a shunt motor will be maximum when the ratio of back e.m.f. to applied voltage is?

Last Answer : The mechanical power developed by a shunt motor will be maximum when the ratio of back e.m.f. to applied voltage is 0.5.

In a power plant if the maximum demand on the plant is equal to the plant capacity, then?

Last Answer : In a power plant if the maximum demand on the plant is equal to the plant capacity, then plant reserve capacity will be zero.

Maximum demand on a power plant is?

Last Answer : Maximum demand on a power plant is the greatest of all "short time interval averaged" demand during a period.

The maximum load that a power transformer can carry is limited by its?

Description : The maximum load that a power transformer can carry is limited by its?

Last Answer : The maximum load that a power transformer can carry is limited by its voltage ratio.

What is the maximum value of power factor?

Description : What is the maximum value of power factor?

Last Answer : 1 is the maximum value of power factor.

The synchronous motor will develop maximum power when the load angle is?

Description : The synchronous motor will develop maximum power when the load angle is?

Last Answer : The synchronous motor will develop maximum power when the load angle is 900.

Explain DC coupled drive circuit with unipolar output.

Description : Explain DC coupled drive circuit with unipolar output.

Last Answer : DC coupled drive circuit with unipolar output: The figure shows the circuit and waveforms

Is the power line voltage available in our homes a dc or an ac voltage?

Description : Is the power line voltage available in our homes a dc or an ac voltage?

Last Answer : The power line voltage available in our homes is AC. Mobile dwellings are the most commonly DC-supplied homes and even then they tend to include AC supply for heavier loads.

A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is ...

Description : A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is (A) 300 W (B) 150 W (C) 45 W (D) 20 W

Last Answer : A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is 150 W

All the rules and laws of D.C. circuit also apply to A.C. circuit containing?

Description : All the rules and laws of D.C. circuit also apply to A.C. circuit containing?

Last Answer : All the rules and laws of D.C. circuit also apply to A.C. circuit containing resistance only.

Application of Norton's theorem to a circuit yields?

Description : Application of Norton's theorem to a circuit yields?

Last Answer : Application of Norton's theorem to a circuit yields equivalent current source and impedance in series.

Briefly explain how the power factor of an inductive circuit can be improved.

Description : Briefly explain how the power factor of an inductive circuit can be improved.

Last Answer : As we know that power factor should be corrected to ensure that the current supplied is cost friendly. Meaning the power factor should be around one but not greater than one(0.8-0.9) in a ... an inductive circuit due to the inductive reactance which oppose the change of current in the ac circuit. 

List any two methods of reactive power measurement in 3 phase circuit.

Description : List any two methods of reactive power measurement in 3 phase circuit.

Last Answer : Methods of reactive power measurement in 3 phase circuit: (i) Two single phase wattmeter method (ii) One single phase wattmeter method

In an A.C. circuit power is dissipated in?

Description : In an A.C. circuit power is dissipated in?

Last Answer : In an A.C. circuit power is dissipated in resistance only.

The apparent power drawn by an A.C. circuit is 10 kVA and active power is 8 kW. The reactive power in the circuit is?

Description : The apparent power drawn by an A.C. circuit is 10 kVA and active power is 8 kW. The reactive power in the circuit is?

Last Answer : The apparent power drawn by an A.C. circuit is 10 kVA and active power is 8 kW. The reactive power in the circuit is 6 kVAR.

The input of an A.C. circuit having power factor of 0.8 lagging is 40 kVA The power drawn by the circuit is?

Description : The input of an A.C. circuit having power factor of 0.8 lagging is 40 kVA The power drawn by the circuit is?

Last Answer : The input of an A.C. circuit having power factor of 0.8 lagging is 40 kVA The power drawn by the circuit is 32 kW.

Pure inductive circuit takes power from the A.C. line when?

Description : Pure inductive circuit takes power from the A.C. line when?

Last Answer : It takes power when voltage decreases and current increases.

The power factor at resonance in R-L- C parallel circuit is?

Description : The power factor at resonance in R-L- C parallel circuit is?

Last Answer : since a rlc circuit at resonance behaves like a pure resistive circuit, i.e there is no phase difference between current and voltage, hence the power factor is unity.

Power factor of an inductive circuit is usually improved by connecting capacitor to it in?

Description : Power factor of an inductive circuit is usually improved by connecting capacitor to it in?

Last Answer : Power factor of an inductive circuit is usually improved by connecting capacitor to it in parallel.

Power factor of an electrical circuit is equal to?

Description : Power factor of an electrical circuit is equal to?

Last Answer : Power factor of an electrical circuit is equal to R/Z, cosine of phase angle difference between current and voltage, kW/kVA.

What is the power factor of purely resistive circuit?

Description : What is the power factor of purely resistive circuit.

Last Answer : Unity that is 1

what is drive circuit in power electronics ?

Description : What is drive circuit in power electronics?

Last Answer : Driver is used for Motion Control through the use of power electronics.

State the Thevenin’s theorem. Also write stepwise procedure for applying Thevenin’s theorem to simple circuits.

Description : State the Thevenin’s theorem. Also write stepwise procedure for applying Thevenin’s theorem to simple circuits.

Last Answer : Thevenin's Theorem: Any two terminal circuit having number of linear impedance and sources (voltage, current, dependent, independent) can be represented by a simple equivalent circuit consisting of a single voltage ... 's equivalent circuit: Step V: Determination of Load current:

State Thevenin’s Theorem.

Description : State Thevenin’s Theorem.

Last Answer : Any two terminal circuit having number of linear impedances and sources (voltage, current, dependent, independent) can be represented by a simple equivalent circuit consisting of a single voltage ... circuit across the two terminals, when the sources are replaced by their internal impedances. 

State Superposition Theorem.

Description : State Superposition Theorem.

Last Answer : Superposition Theorem: In any linear, bilateral, multisource network the voltage across or the current through any branch is given by algebraic sum of all individual voltages or currents caused ... sources acting alone with all other sources replaced by their internal resistances if any.

A 3 -phase, fully controlled, converter is feeding power into a DC load at a constant current of 150 A, the rms

Description : A 3 -phase, fully controlled, converter is feeding power into a DC load at a constant current of 150 A, the rms value of the current flowing through each thyristor of the converter is

Last Answer : Please show the solution for this question